Search Documents

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By Manish Uttarwar, Rajendra Yerpude

India is the third largest producer of coal and the fourth largest in terms of coal reserves in the world. However, new research quite ironically projects that despite the continuing growth in domestic coal production, the country’s exploding economic growth will position it to be the biggest coal importer by 2020. India’s inability to meet the domestic coal demand is mainly attributed to low rate of production, increasing stripping ratio, non use of appropriate technology etc. of coal mining operations here. Presently Indian surface mines which have to shoulder the onerous responsibility of augmenting the coal extraction rate at an even brisker pace are mulling bigger, better and more efficient operations ensuring commensurate rise in stripping work as well. This mammoth task can be accomplished only by deploying smart technologies. In this perspective, cast blasting of overburden emerges on the horizon as a promising alternative for enhancement of the production and productivity of Indian open-pit coal mines.

Jan 1, 2009

Investigation on Comprehensive Utilisation of Nickel Slag from JNMC

Sep 13, 2010

By Dairo E. Chaverra, Carlos Argumedo‑Jimenez, Oscar J. Restrepo‑Baena

This paper presents the results obtained by processing a gold and silver telluride mineral concentrate from a mine in Colombia. An acid wash, also known as acidification, was carried out, followed by oxidation with nitric acid as a pretreatment. Cyanidations of the pretreatment residues were carried out and the results were compared with results from cyanidations of base materials. The removal of carbonates in the acidification, a tellurium extraction close to 90% during the pretreatment, and a 30% improvement in the gold recovery compared to the conventional process were achieved.

Nov 8, 2023

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By S. Lin

A new hydrogen production process, named the HyPr-RING, has been proposed. Fundamental concept of the HyPr-RING is integration of water carbon reaction, water-gas shift reaction and CO2 absorbing reaction in a single reactor. Firstly, thermodynamic analysis was done to judge the possibility to realize the process. It was found that high pressure and temperature condition, such as 20 MPa and 1000 K, is required to promote this integrated reaction. Next, experimental verification of the new process was done under the high pressure and temperature reaction conditions. As the results, integration of above three reactions in a single reactor can be done successfully and produced a large amount of hydrogen as estimated by thermodynamic analysis. Experiments showed that organic materials including coal, heavy oil, biomass, plastics can be used in this process. In the gaseous phase, no pollutants such asH2S, SO2, COS are detected so that gas cleanup system is not required for power generation when this process is used. Finally, a process design was made to estimate process efficiency. Theoretically, 1 mole of carbon can generate 2 moles of hydrogen and cold gas efficiency of this process estimated as more than 80 per cent. The process potentially reduces hydrogen production cost compared with the conventional hydrogen production methods. Keywords: Hydrogen, Fossil fuel, Energy, Process, Supercritical water

Jan 1, 2001

By William S. Sanner

A demonstrated reserve base (DRB) of bituminous coal suitable for cokemaking has been estimated based on the latest published information on U.S. coal reserves. Bureau of Mines analyses of raw coalbed samples were used to classify the coals as low-, medium-, and high-volatile bituminous and grade them as premium, marginal, and latent coking coals. Coal rank was used as the basis for identifying coking coals, and ash and sulfur content were used to determine coking coal grade. The demonstrated reserve base of coking coal for the entire United States is 162.67 billion tons. However, only 18.96 billion tons are premium (metallurgical) grade, and between 80 and 99 percent occurs in the Eastern States. The demonstrated reserve base of marginal-grade coking coal is 31.3 billion tons; more than half the marginal reserve base is in the Eastern States, and most of the medium- and low-volatile marginal coals are in the Eastern States. The Eastern and Midwestern States contain most of the latent-grade DRB of 112.4 billion tons; most (106.6 billion tons) is high-volatile coal, and 98 percent of the medium- and low-volatile latent coals occur in the Eastern States. Based on the worst assumption, which assumes that only premium-grade coals are used for cokemaking, the DRB for high-volatile coal would suffice for 127 years, the medium-volatile coal for 80 years, and the low-volatile coal for 83 years.

Jan 1, 1979

By Keith S. McIntosh

The fire assay process for the quantitative recovery of platinum group elements (PGE?s) prior to subsequent analysis traditionally is a time-consuming process. Samples derive from various ore types and contain PGE?s at the ppm or ppb levels, making concentration of the elements mandatory before assaying. Traditionally sample turn-around times are of the order of 24 hours. The whole sequence of sample preparation, fire assay and subsequent analysis of PGE?s have been automated by Anglo Platinum. Some of the major challenges on the road to automation will be discussed and the novel solutions that were implemented. The engineered solution included robotic automation of the whole sequence, from sample preparation, up to the final element by element assay. The final system allowed for rapid (less than one hour) and accurate analysis of PGE?s even in streams containing very low levels, such as flotation tailing streams and drill core samples.

Jan 1, 2006

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

The following record of the important responsibilities already shouldered by Dr. Ricketts will give some indication of the trust and confidence reposed in him by his colleagues. The Institute is to be congratulated that a man who is already so much engaged should be willing to assume the further responsibility of guiding the Institute's Ship of state during the ensuing year. Louis Davidson Ricketts, who is brother of Professor Palmer or Chamberlaine Ricketts, President of Rensselaer Polytechnic Institute, was born at Elkton, Md., Dec. 19. 1859, was graduated from Princeton University in 1881 with the degree, Bachelor of Science, chosen a Fellow in Chemistry and W. S. Ward Fellow in Economic Geology, and after two years' study given the degree Doctor of Science. Following the completion of Iris work at Princeton, Dr. Ricketts went to Colorado and started to work as a mine surveyor. For the 15 years following, his time was chiefly occupied in reconnaissance work, geological work and mine examination. From 1887 to 1890 Dr. Ricketts was Geologist for Wyoming, and at, the end of that period transferred his operations to the Southwest. where he has since been steadily engaged in large mining projects. He was identified with the acquisition of the property now owned by the Moctezuma Copper Co., a , subsidiary of Phelps, Dodge & Co., at Nacozari, Sonora, Mex. From 1899 to 1901 he was General Manager of the property and during his administration the concentrator and reduction works were completed and the mines put on a dividend-paying basis

Jan 3, 1916

By Jorge Meza

El presente texto señala la aplicación del sistema de gestión de demanda y consumo de energía eléctrica en la fundición de Southern Perú. El sistema está compuesto por un módulo predictor de demanda eléctrica y un módulo de simulación del sistema eléctrico de la planta. El primero, se construyó utilizando redes neuronales con algoritmos de aprendizaje backpropagation, capaz de pronosticar la evolución horaria de la demanda eléctrica con un porcentaje de error cercano. Mientras que el segundo está basado en técnicas de estimación paramétrica, redes neuronales y ecuaciones matemáticas obtenidas por regresión estadística, que simula el comportamiento del sistema de energía eléctrica de la fundición. En ese sentido, los módulos facilitan una adecuada planificación, ya que permiten conocer el comportamiento de la demanda horaria y los patrones de consumo de la planta, incluyendo los componentes de la facturación. Así como las deficiencias energéticas y oportunidades de mejora, sobre la base del análisis de la información acerca de los equipos, procesos y planes de producción, así como programas de mantenimiento.

Sep 24, 2008

By K. E. Stanfield

[Asphalt and road oil are the principal products manufactured from Wyoming ?clack oils? which, because of their high asphalt an high sulfur content, are difficult and costly to refine into high-grade motor fuels, burning oils, and lubricants by pre sent methods. Accordingly, the remand for these asphaltic residuums for the construction of roads and other uses is a controlling- factor in the quantity of crude oil produced. The increasing utilization of special asphalts as inexpensive bonding, insulating, and waterproofing materials indicates the desirability of obtaining information on the yield and properties, of asphalts from Wyoming black oil to promote a wider and more stable caret for these asphaltic materials.]

Jan 1, 1941

By Jiulong Cheng

Underground coal mining causes overburden deformation and failure, one major form of which is bed separation in the overburden. Surface subsidence can be controlled by injecting grout into the bed separations. For a long time, the grouting results of bed separation can not be validated. This is the problem in the application of this technique. This paper analyzes the conditions leading to bed separation, develops mathematical models for seismic wave fields generated before and after bed separation, and bed separations grouted with different materials, and computes the seismic wave field characteristics using the finite difference method. The results show that the existence of bed separation causes changes in the characteristics of seismic wave field, and that different grouting materials generate different seismic wave field characteristics. Intact strata, bed separation, and bed separation filled with air or water all display distinctive seismic wave field in amplitude and frequency spectra. After mining, the original location that provides strong seismic reflection wave no long exists. It is replaced by a weak and syncline-shaped reflection wave. The area, where the seam wave disappears, is larger than that of the mined area. The location, where a bed separation occurs, generates a set of reflection waves stronger than the normal one. The energy of the reflection waves varies with the materials filling the separations. Bed separations filled with air generate stronger reflection waves than those filled with water. The major frequencies for those filled with air are lower than those filled with water. Therefore, it is possible to determine the property of filling materials by analyzing and comparing the amplitude and frequency spectra of the reflection waves. Case studies of application of seismic method for exploring bed separations and grouting were analyzed. The results show that it is feasible to use seismic technique for exploring bed separations and grouting.

Jan 1, 2006

By Seong- Rin Lim

Light-emitting diodes (LEDs) are regarded as environmentally friendly light sources due to their high energy efficiency and lack of mercury content. LEDs are used for a variety of domestic and commercial lighting systems, where they are replacing incandescent and fluorescent lamps at a rapid rate. Incandescent lamps inefficiently consume energy because electricity is mostly converted to heat rather than light. This causes unnecessary environmental impacts and energy consumption associated with power generation and transmission from a life cycle perspective. Although fluorescent lamps are more energy-efficient than incandescent lamps, their disposal at end-of-life presents special challenges because of the presence of toxic mercury. Despite the seemingly apparent advantages of LED, very few studies have rigorously addressed potential environmental consequences of their disposal. Specifically, LEDs are designed with III-V semiconductors that presumably consist of toxic and rare materials, including arsenic, gallium, and indium. We hypothesize that, depending on their concentrations and leachability, these constituents may also contribute to render LEDs as hazardous waste at the end of their useful life.

Jan 1, 2010

By Claude Cunningham

The primary reason for blasting is to fragment rock. In production blasting, the fragment sizes produced are known to exercise an overwhelming influence over working costs: handling costs and tonnage throughput are directly affected by secondary breaking, loading and crushing, all functions of fragmentation. In addition, particular size fractions are frequently of intense interest in terms of market or process requirements.

Jan 1, 1995

By Philip K. Hopke

A systematic study of the mechanism of interaction of 218Po(RaA) armed by the decay of 222Rn with airborne particulate matter has been made. The rate of attachment of RaA to particles in the diameter range of 0.1 µm to 10.0 µm has been measured as a function of particle size, concentration, and composition, radon concentration, time of interaction, relative humidity and temperature. It was found that under the conditions in these experiments the attachment rate was proportional to the square of the particle diameter and varied with temperature and relative humidity. The composition of the particles apparently has no effect on the attachment. The variation in attachment rate was related to a sticking probability coefficient of approximately 0.02 that varies systematically with temperature and humidity. In addition, the rate of deposition of RaA on the wall of the attachment kinetics system was measured and also found to change with temperature and relative humidity.

Jan 1, 1980

By J. E. Chilton, T. Mal

Methane monitoring at the mine face is essential to assure a safe work environment in underground coal mines. Machine-mounted methane monitors must be used to continuously monitor methane levels during mining. Monitors used on mining machines must be approved by MSHA and properly maintained to provide protection for workers (30 CFR 75.342). To provide protection the instrument must give accurate readings of current methane levels. Accuracy is maintained by calibrating the instrument with a standard gas at least once every 31 days. Instrument “response time” determines how quickly measurements will change to reflect current concentrations. At present there are no criteria for measuring the response time for a ma-chine-mounted methane monitor while underground. This study examined a procedure for measuring the response time of a machine-mounted methane monitor. Response times were measured using methanometers obtained from three different manufacturers. The effects of the measurement technique and methanometer sensor head design on response time measurements are investigated. Techniques for reducing variation in response time measurements are discussed.

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Steve C. Albrecht

The objective of this study is "to assess the impact of surface mining on soil compaction in the Midwest". The study revolves around a unique field sampling program targeted at four mine sites utilizing four distinct types of soil movement of midwestern prime land. Through the preparation of a final report for use as a guidebook, an assessment is made of the degree to which surface mining operations contribute to the soil compaction problem. The final report is formulated through the use of field study data as well as information gathered in an intense literature review. The final report centers on applying collected data to practical field applications. Soil sampling on the four mine sites centers on a comparison of natural and replaced soils for moist bulk density. This characterization evaluates changes in density and texture throughout the soil profile to a depth of 48 inches. Fertility of the topsoil is also assessed for natural and replaced soils. During field sampling and observations, a base of information has been gathered to compile a case study on each mine site. The report accesses the regulations in the prime farmland areas through the use of a matrix. The regulatory matrix allows easy access of mining personnel to State and Federal regulations.

Jan 1, 1982