Search Documents

By David R. Mitchell

IF you are the owner of a mine, or a mine executive, or just an ordinary miner, and have a son about to go to college, do you urge him to take up mining engineering or do you try to dissuade him from such a course? If you live in the East, or the Middle West and your interest has been in coal rather than metal mining, the chances are that your young hopeful will be urged to do almost anything else rather than follow in father's footsteps.

Jan 1, 1939

By L. G. Marshall

WHILE surveying in a small Western mine, the following problem was encountered: Two traverses had to be connected by running a traverse line down the main hoisting shaft, which was the only connection between the two levels. The shaft was inclined at about 80 deg. from the horizontal and measured 8 by 10 ft. The distance between levels was about 110 ft., measured on one side of the shaft. The surveying equipment consisted of a transit, tripod, level rod, 100-ft. chain, and plumb bobs. There were no side or top the- scope attachments with which to take large, vertical angles. Therefore, we were confronted with the problem of taking readings between two points, one of which could not be seen through the instrument when set up under the other point, owing to the obstruction of the horizontal plate, and of measuring the distance between these points with a chain that was too short. The method of a line of plumb bobs down the shaft was impractical because a setup would be needed part way down the shaft, which would call a halt to all hoisting operations for some time. After considerable experimentation the following method was used.

Jan 1, 1936

By B. K. Loveday

A Colloquium on 'Control and Simulation in the Minerals Industry' was held at the Holiday Inn, Milner Park, on 20th September, 1984, in conjunction with the Electra Mining Exhibition. A total of 170 persons attended the very full morning programme, which began with an opening address by the President, The South African Institute of Mining and Metallurgy, Mr l.D. Austin. He outlined the reasons why computers were being used to an ever-increasing extent for control and simulation in the minerals industry. The computer was even used to check, among other things, the validity of the signals it was receiving by mass-balance calculations.

Jan 1, 1985

The dust exposure of the longwall shearer operator is usually determined by his position relative to the cutting drums. The dust generated during cutting may travel up-wind, against the primary airflow, and be carried out into the walkway where it can contaminate the intake air for as much as 10 feet outby the shearer operator's controls. Thus, both head and tail drum operators are exposed to un-acceptably high levels of air-borne respirable dust. One Solution The latest generation of long-wall shearers has features that make the use of radio remote or umbilical (hard wire) remote control relatively easy to implement. Remote control can enable shearer operators to control machines from positions that are less dusty than normal control stations. With either type, the head-drum operator can now control the shearer from a position up to 20 feet on the intake-air side of the shearer, while the tail-drum operator's station is now located across from the head drum.

Jan 1, 1984

By George C. Riley

While the general public has little knowledge or appreciation of either the mining or explosives industries, modern civilization could not exist without them. They are to-day the key industries of the world. In common with many other industries the demands of the war greatly stimulated the production of explosives and the research necessary for such increased production. Production, supplies of all kinds, munitions of all sorts and then again production, practically regardless of cost, were the first reactions to the imperative war demands of the governments of the world. Following the war there was a momentary lull, then first gradually but with quickening acceleration, particularly in a recent slump, the situation was reversed - cost and not production was the dominant factor. Some industries readjusted themselves very rapidly and completely. Others were but partially re-adjusted and others again only carried out the process of deflation in certain departments. The explosives industry in Canada has not only thoroughly deflated itself, but has learned to apply to commercial disruptive explosives, the best, most efficient and most economical methods of manufacturing developed during the war. As a consequence, miners have at their disposal to-day better and more different kinds of compressed energy than ever before in all the long history of mining.

Jan 1, 1925

By Scott Turner

OUR Institute, in its annual Directory, states the following: The purpose of each Technical Committee is to further the development of the special mineral industries in its field, chiefly through obtaining and discussing papers suitable for publication by the Institute. The proper field of the new Health and Safety in Mines Committee is judged to include the entire mining industry, and involves the multitude of health and safety problems arising in all kinds of mining operations. The mining industry in the United States has made much progress during recent years in reducing accidents. This advance has been widespread, and has been especially notable in the mining of iron ore. Yet the statistics of the U. S. Bureau of Mines, when compared with figures of the National Safety Council for other industries, show that mining still has a higher personal mishap rate than any other major industry in this country. In addition, studies of dollars-and-cents cost of casualty occurrences indicate that an important part of our mining cost, held by various authorities to be as much as 10 per cent of the total, is due to accidents.

Jan 1, 1933

By Wesley G. Josephson

THE MINING PROPERTY of the Argonaut Mining Co., Jackson, Calif., is one of the oldest on the Mother Lode. A vein outcropping on a hill in this section could not long elude the eye of the forty-niner, so it was first discovered in 1850. From that time until 1893 the Pioneer mine, as it was then called, limped along under various poorly equipped and financed operators who tried tapping it by trenching and tunneling. Then the Argonaut Mining Co. took over the property and sank the present 65° inclined shaft in the hanging wall of the vein. The mine workings have now reached the 6000-ft. level, which is 5283 ft. vertically below the surface, or just 3 ft. over a mile. The total production of the mine is uncertain, because of lack of early records, but from 1893 to 1932 it is known to have produced in excess of $17,000,000.

Jan 1, 1932

By M. D. Cooper

UNDERGRADUATES in mining engineering may be prepared for work by giving them sound instruction in the courses generally considered essential to the profession. The industry is not deeply concerned about the details of those courses. The average man in the coal industry does not wish to insist upon a rigid program. Therefore, he differs little from those in the teaching profession-who evidently are not unanimous in their opinions, or all college catalogs would be alike. For the good of the profession, it is just as well that there should be differences in regard to details. It appears that students graduating in mining engineering from the accredited institutions receive similar instruction.

Jan 1, 1950

James Gayley, Braddock, Pa. (communication to the Secretary) : Mr. Potter has made reference to our practice at the Edgar Thomson works in the direction of increasing the life of the lining, and mentions the product of one of our furnaces as having reached a total of 370,000 tons. It may be interesting to know that this furnace has been put out of blast with a record of 452,685 tons, after a run of three years and nine months. A companion-furnace to this will produce, hefore the present year is ended, half a million tons. As Mr. Potter has quite correctly designated this as " the newest problem in furnace-practice," a description of the construction of this furnace lining may be Welcome to members. The bricks used in the lining are 9 and 134 inches long, with the requisite quantity of straight and key-shapes to turn the circle. There bricks are well suited for enclosing the numerous bosh-plates used for cooling. The bosh-plates (the efficient fortress of the lining) extend from the top of the tuyere arch to the mantel, and are inserted in rows, 18 inches to 2 feet apart. These form a perfect defence against encroachment on the bosh-lining, and leave the bosh at the end of the blast of the same thickness as at the beginning. The protection afforded by these bosh plates is the principal cause of the increased duration of the furnace-lining. But it must be noted that the shape and material of the plate are essential elements. The most serviceable plate is that made of bronze or copper. We have tried every form of iron plates without obtaining satisfactory results. These were replaced with bronze plates, built into the lining, which gave excellent results so long as they did not leak; but when this occurred, as it did in time, the water was shut off, and, since the plates could only be removed with difficulty, they were allowed to burn off. This permitted encroachment on the bosh-walls, which thus became enlarged beyond the limit required for economical practice. With the introduction of the removable plate, made tapering on the sides, with plain surfaced top and bottom, these troubles have

Jan 1, 1895

By K. Hajmrle

The production of nickel coated mica composite powder by hydrogen reduction of a nickel ammine sulphate solution, followed by the production of molded plastic samples containing Ni/Mica is described. Sample preparation by injection or compression molding is outlined and the better results in compression molding are explained by the combination of better particle-to-particle contact, less particle breakage during processing, and more random particle distribution in the plastic. Three volume resistivity measurement techniques are described and compared. Two of them (conductive paint and silver-rubber electrodes) are found reliable and are used throughout the work. The influence of nickel content and particle size of Ni/Mica on volume resistivity is evaluated and the optimum product defined. One of the most important assets of Ni/Mica, its ease of injection molding, is demonstrated by the good electrical properties obtained with little optimization of the injection molding process. Surface roughness of molded plastics with and without Ni/Mica is briefly discussed. Shielding effectiveness of Ni/Mica in four plastics (PP, ABS, PBT and PC) is presented and correlated to volume resistivity data for the same materials. The addition of 15 to 50 weight % Ni/Mica (3 to 16 volume %) to plastics and subsequent injection or compression molding produces composite materials having low volume resistivities (0.03 to 1 ohm.cm) and high shielding effectiveness (40 to 70 dB).

Jan 1, 1988

By F. W. Pereira

The Montana Talc ore body was discovered in the summer of 1983, in the Gravelly Range, approximately 25 miles south of Ennis, Montana. Initial drilling indicated a plus-million-ton ore body of high-purity talc. Preliminary analyses were performed on the ore cuttings, .including chemical analysis, brightness measurements, and microscopic evaluations of the structure of the talc. The results indicated the talc was similar to that currently being marketed from Montana and probably would have good commercial value.

Jan 1, 1989

By George S. Rice

"The successful use of the gas mask by the American Army it France in combatting the poisonous gases of German .shells caused many Army men to feel that the as masks were proof against any kind of gas which might be encountered. The result has been that from time to time there have been reported in the press, deaths of former army men through using their masks to enter various kinds of gases such as illuminating gas, gasoline vapor, and the gaseous atmospheres produced by mine fire. Such a case has just been reported from a mine, in Copperopolis, California, where a former Army man lost his life in descending a mine shaft filled with the fumes of a mine fire. Another man who, in attempting to rescue him, merely used a dust respirator, lost his life also.While the American type of the Army gas mask was developed by the Bureau of Mines for the War Department, and since the war a section of the Bureau's in¬vestigative force has been developing industrial gas masks for certain specificgases, the Bureau has repeatedly called to the attention of the public the fact that such masks have serious limitations and in no case should a gas mask be used in underground workings for the reason that there may be an insufficient amount of oxygen to breathe, (and the gas mask does not supply oxygen) or there may be present carbon monoxide, which the Army mask will not remove, and there always is some carbon monoxide produced by a mine fire or by a coal-mine explosion, or by a blast of dynamite or other explosive.It is true that the Bureau has been developing a mask which may take care of a small percentage of carbon monoxide, that is, one per cent and under, but in mine fires and after explosions, there may be, and frequently is, a much larger percentage of carbon monoxide in the mine atmosphere. Masks such as these, for small percentages of carbon monoxide and associated gases are for use in connection with industrial surface plants, as for example, on the top of a blast furnace or around gas producers in the open air."

Oct 1, 1920

By Fred J. Miller

FRED J. MILLER was born in Ohio, in 1857. He had a common and high school education, supplemented by personal study and special instruction. After serving a 4-year apprenticeship and working in various capacities in machine shops, he became a contributor to mechanical journals and finally a member of the editorial staff of The American Machinist, where he remained for twenty years, the last ten years as editor-in-chief of the magazine, and vice-president of the publishing company. On retiring from journalism, he was for nine years general manager of a group of typewriter factories, and was then commissioned Major of Ordnance in the U. S. Army, being stationed during most of his service at Rock Island Arsenal, where he organized the Civilian Service Division of the Arsenal. He is now a member of the Technical Advisory Committee of the War Claims Board at Washington. Major Miller became a member of the American Society of Mechanical Engineers in 1890, and has always taken an active interest in its affairs, having served on a number of important committees, and as a member of Council from 1904 to 1907, inclusive. He was elected President in December, 1919.

Jan 1, 1920

By I. Spector, A. J. Smith

In 1967, BACM Industries Limited started producing walboard at Saskatchewan's first gypsum products plant, located in Saskatoon, using, as a basic raw material, gyp-sum rock supplied from the company's mine near Amaranth, Manitoba. This paper describes the geology of the Amaranth gypsum deposit, the method of mining the rock and the manufacturing facilities used to produce wall-board.

Jan 1, 1970

By Charles F. Park

CORRECTLY speaking, iron ore is limited to any naturally occurring rock from which iron may be extracted at a profit, but in practice the term is frequently used to indicate borderline material or inaccessible material that may in the future become commercially profitable. This distinction is much more than quibbling about terminology. When a layman hears that there are about 45 billion tons of iron ore in the world he naturally thinks that sounds like quite a bit of rock, and what is the use of worrying about the depletion of so plentiful a material. He does not realize, nor does he stop to analyze. why iron ore in Europe and Japan may carry no more than 30 per cent iron while tremendous quantities of 50-60 per cent iron ore in Brazil are not exploited. To people in the iron industry the answer is obvious: the Brazilian material is inaccessible, and there is no suitable fuel near-by. In places closer to home, submarginal ore in considerable quantity contains undesired impurities, such as sulphur, phosphorus, or titanium.

Jan 1, 1947

By Barbara J. Arnold

Combat Infantrymen’s Badge and Bronze Star Medal. Following his discharge from the Army, he re-entered SDSM&T in 1946 and earned a B.S. degree in Metallurgical Engineering in 1948. He then received an M.S. from Montana Tech (MT), worked several years in industry and then as an Assistant Professor at the University of Washington (Seattle). He joined his Montana Tech colleague, Douglas W. Fuerstenau, at The Massachusetts Institute of Technology (MIT), receiving his doctorate in 1957. While at MIT, he married Clare M. Donaghue of Dorchester, Massachusetts, in 1955

Jan 3, 2022

By James R. Jones

"The General Leasing Law, which provides for the leasing of deposits of coal, oil, oil shale, gas, phosphate, and sodium in public lands, was approved February 25, 1920.One of the outstanding features of this legislation is the fact that it opens for prospecting and exploitation lands and deposits which have been withdrawn from public use, some of them for several years, pending enactment of legislation better fitted to control the mining and utilization of the particular mineral deposits referred to. These lands are not only made available to the public, but they are opened up under a system which defines better than was ever done in the pas the rights which may be acquired under it.The oil operator, for example, under this legislation will know definitely the extent of the rights he has acquired, as well as the legal conditions under which his expensive drilling and other work of exploration are to be conducted. No longer will he be harassed by the possibility that while he is spending his capital in drilling operations in an effort to make a discovery of oil, his legal rights be contested, in which event the superiority of his claim can only be upheld -- if at all -- after long and expensive litigation. By the same token the coal operator will now be free from the embarrassing restrictions of the old coal-land laws respecting the amount of such land which may be purchased by one person.At the same time that these advantages are being enjoyed by the operators, the public will be guarded against wasteful methods of drilling and mining the oil and gas, and coal deposits, and the other mineral substances enumerated in the act, to the end that these products of Nature, which can not be replaced, may be utilized with a minimum of loss."

Mar 1, 1920

By D. A. Smith

The successful integration of overburden casting techniques into the mine production cycle can be an extremely cost effective use of explosives. The entire mining cycle revolves around the cast blasting and to be successful requires a great deal of planning and cooperation. Several operations of Cyprus Coal Company in the Appalachian coal fields have successfully integrated blast casting into their mine plan. This paper will detail the parameters and necessary controls to integrate an overburden casting program into a surface coal operation.

Jan 1, 1993

By Hollis Peacock

THE Bingham area in the West Mountain mining district on the eastern slope of the Oquirrh range, some 28 miles southwest of Salt Lake City, has been the most consistent producer for the United States Smelting Refining and Mining Company, production having been continuous, except for minor interruptions, since the organization of the United States Mining Co. in 1899. This production has come from fissures and mantos largely within limestone members aggregating something less than 10 per cent of a thick quartzite sequence of Pennsylvanian age which has been warped into an open syncline plunging northwesterly. Bedding on the easterly limb dips 10°-45° but steep-ens to 90° and even overturns on the westerly limb. Ore bodies cluster about the more northerly of two elongate interconnecting stocks of monzonite which have risen in an axial position within this syncline. Largely within the more northerly of these stocks is the low-grade copper ore body exploited in the Utah Copper open cut of the Kennecott Copper Corp. The values, in seams, minute fracture fillings, and disseminations of pyrite and silica, pervade not only the stock but adjacent sediments, and form a nebulous, sprawling mass which both mineralogically and geographically is the center of the district. The more southerly of the twin stocks appears to be comparatively inert and without obvious relation to mineralization. which

Jan 1, 1948

By W. E. Cockfield

"The Stump Lake mining camp is in Nicola mining division of southern British Columbia. It lies about halfway between the cities of Kamloops and Merritt.The deposits at Stump Lake are among the earliest lode discoveries of British Columbia, many of the claims having been staked between 1882 and 1885. A considerable amount of work was done prior to 189Cl, after which very little was done until 1916. Since that time mining has been carried on at intervals, much of it on the same deposits, by a number of companies, including the Donahue Mines Corporation, the Planet Mines and Reduction Company, the Nicola Mines and Metals Company, the Consolidated Nicola Goldfields, Limited, and others. According to the British Columbia Department of Mines, total production from the area has been: gold, 8,520 oz.; silver, 259,413 oz.; copper, 40,822 lb.; lead, 2,208,859 lb.; and zinc, 367,869 lb. Most of the production has come from the Enterprise vein and a branch of the Enterprrsethe King William vein."

Jan 1, 1954