Search Documents

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

By Joseph A. Hrabik

The Bureau of Mines compared the feasibility of mining deep phosphate deposits by a borehole mining system with mining by proven conventional techniques. An economic comparison of the borehole mining system with conventional dragline and bucket wheel excavator mining systems was completed at various mining depths and production rates. Hypothetical phosphate deposits, with various overburden thicknesses and reserve tonnages, were defined. Geologic conditions necessary for the application of the borehole system were identified. Discounted cash flow analyses based on derived capital and operating costs were used to generate rates of return and product prices. Borehole mining was found to be more economical where overburden thickness was 150 ft or greater; however, at 50- and 100-ft thicknesses, conventional surface mining was more economical. Overburden thickness has a great effect on the economic feasiblity of the conventional mining systems but less effect on the economics of borehole mining. Economies of scale are only realized in conventional mining, since larger equipment is employed to achieve greater production, whereas increased production from borehole mining is achieved using additional equipment units. A comparison of the environmental effects of borehole and conventional surface mining systems showed that borehole mining is environmentally more desirable.

Jan 1, 1983

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By I. A. Mutemererwa

This paper investigates the role of vertical integration between chrome ore mines and ferrochromium smelters in the location of ferrochromium production capacity in South Africa and Zimbabwe. Vertical integration is important in understanding the increasing competitive position of these two countries as observations show that an increasingly larger share of the global market has been coming from integrated producers. The paper argues that the increased vertical integration between mines and smelters in South Africa and Zimbabwe has led to a lower cost of chrome ore as an input compared with other producers. Underlying this hypothesis is the basic tenet that, more likely than not, production will take place where the costs are lowest. The paper concentrates on high carbon ferrochromium (HCFC) production in market economy countries (MEC). Using an ordinary least squares model, the study tests the relationship between low chrome ore costs and vertical integration shows a statistically significant relationship. These findings partially support the view that the control of sources of chrome ore is a major source of competitiveness. Keywords: competitiveness, ferrochromium (ferrochrome), ordinary least squares, dummy variables, vertical integration, southern Africa.

Jan 1, 2000

By Luis-Fernando Contreras, Juliano Maran, Richard LeSueur

A risk study was carried out at the Cerrejon coal mine in order to assess the impacts of pit slope failure in terms of safety of personnel and destruction of equipment with economic consequences. Results of the assessment enabled the definition of risk treatment requirements and the identification of key aspects to consider in a risk treatment plan. The approach included the following tasks: (1) Assessment of the total probability of failure (POF) representative of the stability conditions of typical footwall and highwall slopes. For this purpose, stability analyses were carried out to define the Design POF, which accounts for the variability of strength parameters and represents the normal conditions considered for slope design. Strength parameters for highwall slope analysis were derived from borehole data obtained with a geotechnical drilling campaign. The Total POF was estimated through the use of Source Response Diagrams (SRD) in order to incorporate other sources of uncertainty not accounted for, like changes in geometry, variability of rock conditions due to geological or operational factors, changes in groundwater conditions and occurrence of seismic events. (2) Assessment of the consequences of footwall and highwall slope failure on safety of personnel. The assessment was performed through the use of event tree analysis to establish the probability of fatality caused by slope failures, from the Total POF defined in the previous task. This analysis required the evaluation of personal exposure to slope failures. Also, the assessment included benchmarking of acceptability criteria in terms of probability of fatality and the evaluation of options of risk mitigation to comply with these criteria. (3) Assessment of the consequences of footwall and highwall slope failure in terms of economic losses associated with impact on equipment. The analysis included the evaluation of equipment exposure to slope failures, and it was performed through event tree analysis to establish the probability of an economic loss associated to total or partial lost of equipment, from the total POF value defined in the first task. The magnitude of the economic losses was estimated from the costs of damaged equipment, lost production and site restoration. Options of risk mitigation were also examined in terms of economic losses. The risk assessment process applied to the Cerrejón mine showed how the system can be applied to evaluate the consequences of failure in terms of personnel safety and economics and to identify the more adequate risk mitigation options. The system can be an extremely powerful tool in the mine design process and provides the opportunity to rationalize the geotechnical information requirements, once the risk criteria have been defined by management. The main purpose of this paper is to present the process; therefore, the emphasis has been put on the methodology followed rather than on the actual results obtained.

Jan 1, 2006

By Luo Yang

It has been known that after initial pile driving, pile capacity gain over time (set-up) could constitute a significant portion of the total pile capacity. In the past, there has been very little guidance for incorporating pile set-up capacity in design. This may be due to large uncertainties involved in predicting the pile set-up. A comprehensive statistical database is developed to describe the increase of pile axial capacity with time, known as set-up, when piles are driven into sand. Based on the collected pile testing data, pile set-up is significant and continues to develop for a long time after pile installation. The statistical database shows that a lognormal distribution can be used to describe the probabilistic characteristics of the predicted set-up capacity using Skov and Denver?s equation. The main objective of this paper is to incorporate the set-up effect into a reliability-based Load and Resistance Factor Design (LRFD) of driven piles in sand. A First Order Reliability Method (FORM) is used to derive separate resistance factors that would account for different degrees of uncertainties associated with the measured short-term capacity and the predicted set-up capacity from the proposed semi-empirical equations. The incorporation of set-up effects in the LRFD helps improve the prediction of the total capacity of driven piles, resulting in more economical design. A practical design procedure within LRFD framework to incorporate the pile set-up effect is outlined at the end of the paper.

Jan 1, 2006

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By E Hollinger, J L. Mauk

Gold-silver mineralised veins at Favona, represent a new low-sulfidation epithermal vein discovery that occurs less than 1 km southeast of the world-class Waihi deposit. The Favona vein is hosted in Late Miocene andesitic lava flows and local dacitic tuffs that are intensely altered to quartz, adularia, chlorite, illite or interstratified illite-smectite (with ten to 70 per cent smectite) and pyrite. Adularia is widespread and envelops the veins, whereas chlorite and illite are mostly restricted to the footwall, and illite-smectite is confined to the hanging wall of the Favona vein. At shallow levels, kaolinite, cristobalite and rare alunite overprint the above minerals. A polymict hydrothermal breccia also occurs above and in the hanging wall of the Favona vein and contains clasts of altered andesite and various quartz vein fragments. Fluid inclusions in quartz veins sampled over a 300 m vertical interval have a homogenisation temperature range of 175¦ to 266¦C and dilute apparent salinities of 220¦C and grading into illite-smectite and local smectite which formed at 2. In contrast, late kaolinite, cristobalite and alunite formed from descending steam-heated acid-sulfate waters. Overall, the Favona and Waihi deposits are interpreted to have formed at similar levels in a single low relief hydrothermal system, with each deposit representing a distinct zone of fluid upflow.

Jan 1, 2002

By Craig Bournes, David Chapman, Michael DiPonio

Historically, boulders are a frequent source of problems in soft ground tunneling. During tunnel construction, the need to manually break and remove boulders as obstructions causes delays to the project. Repairs to a tunnel boring machine (TBM) can also be a source of delays. Managing these problems is difficult since normal soil investigation techniques do not accurately predict the presence or frequency of boulders. This has lead to considerable number of claims for extra costs and delays during the construction of soft ground tunneling projects. These issues are exacerbated in pressurized face tunneling systems where there is limited access to the TBM cutterhead for obstruction removal and/or cutterhead maintenance. The project team that built the Big Walnut Augmentation/Rickenbacker Interceptor (BWARI) Project for the City of Columbus successfully managed the design and construction of a 4,267 mm (14 ft) diameter soft ground tunnel with high boulder concentrations in a complex geologic setting. The management of the boulder issue tookplace during several phases of the project.

Jan 1, 2007

By José Díaz Barrios

El proceso de la explotación minera de la veta Oroya Techo, perteneciente a la mina Casapalca, ha generado un desequilibrio del macizo rocoso, donde la energía que la roca de la caja, piso y techo (volcánicos de la formación Carlos Francisco) no pueden soportar mas allá del límite de su resistencia y deformabilidad natural, es liberada o “compensada” con el estrujamiento plástico de la veta Oroya Techo (estructura carbonatada). En ese sentido, el presente texto describe una manera de cuantificar dicha deformación a través del monitoreo de convergencias, donde se emplea un simple extensómetro de cinta manual y asímediante una análisis estadístico, seleccionar estaciones de convergencia por rangos de mediciones.

Sep 12, 2005

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

By John Frostiak

"Kahama Mining Corporation Limited, a wholly owned subsidiary of Barrick Gold Corporation, poured the first dore bar and filtered the first concentrate produced at the Bulyanhulu mine on February 28, 2001. This event marked the completion of the initial development of the Bulyanhulu Mine – Barrick’s first mine located outside of the Americas.Bulyanhulu is a 2,500 tpd underground mine located in the Lake Victoria gold belt of northern Tanzania. Gold is recovered as a gravity concentrate and smelted on site to produce dore bars or collected in copper concentrate that is shipped to offshore smelters. The facilities were constructed to meet Canadian standards. Unit operations include single stage crushing, SAG milling, gravity recovery, flotation, thickening and dewatering. Tailings are converted to paste and returned underground as paste backfill or pumped to the surface tailing site. The surface paste tailing disposal system is believed to be first of its kind in the gold industry. Paste disposal has several advantages over slurry, including lower dam construction costs, reduced water losses, and lower reclamation costs. This paper describes the facilities and discusses the challenges faced during development and construction including logistics, lack of infrastructure, recruiting and training, security, and social issues as well as initial operating results.INTRODUCTIONBarrick Gold Corporation completed the Bulyanhulu mine development in 2001. Capital cost of the project was US$280 million. The mine produced 241,575 ounces from start of milling to year end at a total cash cost of $197 per ounce. Numerous challenges were overcome in the mine’s development due to the general lack of infrastructure in Tanzania and the mine’s location some 1200 km inland by road from the port of Dar es Salaam."

Jan 1, 2003

The mercury, gold, silver, copper, lead and zinc values of soils over altered and mineralised rock were determined to establish the potential use of mercury as an indicator element in geochemical prospecting. The results are presented to show that mercury can be used successfully in prospecting for precious metal mineralization in the Thames-Waihi area.

Jan 1, 1979

A computerised cataloguing system for geological specimens is described. The catalogue is designed for use with a compactus-type storage system. The information stored in the catalogue for each specimen includes the type of specimen, locality information in terms of standard ~ap sheets and descriptive location, geological age, stratIgraphy, and specimen descriptions. The catalogue can be interrogated at any level of detail on the basis of any combination of these specimen parameters.Other information stored for each specimen 'is the compactus address, collection date, reference information and the type of analyses performed on that specimen:Any mterrogatlon produces a listing of those specimens which satisfy the search criteria.

Jan 1, 1974

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

By Charles De Witt

The ore treated at the reduction plant (called Yangdei) of the Chiksan -Mining Co., Korea, is brought from four of the company mines, and from the small tribute mines. The largest shipments conic from Sajunkohl mule, situated about a mile and a half from the mill (Fig. 1). The ore is quartz of medium hardness. The overage assay value in gold is $6.95 per ton. At the mine the ore is put into bin,, and is Mien trammed over an 8 per cent. grade to the tipple bins above the mill, where the ore is drawn through the hull holes as desired. The capacity of the tipple bins is about 3,500 tons. On, from Moonsukohl, Chung Tarrie, Yang Chun, and the tribute mines is brought in by bulls and bull wagons. The bulls carry from 350 to 800 lb.; the average wagon load is about 1,200 lb. (Fig. 2). One shovelful of ore out of every ten is taken as a sample. Considerable ore

Jan 5, 1915

By S. M. Bradshaw

The principles of microwave heating are discussed with reference to dielectric properties, heating phenomena and microwave equipment. Microwave regeneration of granular activated carbon for the carbon-in-pulp process is examined on a laboratory scale, with special attention being given to highlight the problem areas and specific considerations related to microwave heating. Results indicate that microwave regeneration of carbon with 40% moisture on a wet basis by heating to 650°C with steam addition regenerates the carbon to virgin carbon activity levels but with a higher abrasion resistance. A preliminary economic assessment showed that the capital cost for 120 kg/h microwave unit would be R540 000 with an annual operating cost of R 320/t carbon. These figures yield a return on investment of 12%. The aim of this paper is to provide an introduction to microwave heating and to illustrate its application to the microwave regeneration of granular activated carbon for the carbon-in-pulp (CIP) process.

Jan 1, 1998

By R. Flatabø, K-E. Johansen, L. Hunsbedt, P. M. Cowx, J. A. Bustnes

Eramet and Tinfos are two producers of manganese alloys in Norway, which have worked hard for several decades to improve both the internal and external environment. Furnaces producing ferro- and silico- manganese alloys generate large amounts of off-gas that contains substantial amounts of dust, heavy metals and organic by-products. The dust is separated from the gas in venturi scrubbers by washing with water. The water is cleaned and recirculated, and the surplus water coming from moisture in the raw materials, is discharged to the adjacent fjords after further treatment. Emission figures show that the discharge of suspended solids, manganese, zinc and PAH (polycyclic aromatic hydrocarbons) have been reduced substantially over the last three decades as a result of process improvements and installation of state of the art environmental control measures. The two plants were the first world wide to install mercury cleaning of the off-gases from the furnaces. Mercury emission reduction has exceeded 90%. Concerning other environmental issues, such as utilisation of off-gases for energy recovery and chemical purposes, both plants have achieved good results. Major effort in the environmental work has come from the plants themselves, but other players like FFF, The Norwegian Ferroalloy Producers Research Association, and SFT, The Norwegian Pollution Control Authority, have contributed to the achieved results.

Jan 1, 2007