Search Documents

By N. M. Parikh, T. J. Koppenaal

The strengthening mechanism of fiber-reinforced silver has been investigated as a function of fiber density and fiber material. Stress-strain curves were determined in the range 2 x 10-6 to 2 x 10-3 plastic styain and slip lines were examined. The yield strength at 0.2 pct permanent strain is markedly dependent upon fiber density but the stress necessary to initiate plastic deformation is independent of fiber density. The strengthening mechanism of the fibers is shown to be malogous to grain boundary strengthening in poly crystalline metals. The variation in strengthening with different types of fibers is also noted and discussed. In recent years, considerable progress has been made in the understanding of the mechanical properties of two-phase systems, particularly in the classical dispersed-phase alloys where the separation between the dispersed phases is 0.01-0.1µ. However, little work has been done on fiber-reinforced metals where the dispersed-phase separation is considerably larger than this. Parikh1 investigated the mechanical properties of many fiber-reinforced metals and found that two general relationships are always observed, as follows: 1) A fibrous network incorporated into a second weaker metal strengthens the latter, and the amount of strengthening increases with fiber concentration. 2) At a corrstant fiber concentration, the amount of strengthening in a given matrix can vary considerably, depending upon the type of fiber employed. The object of the present investigation was to examine the fuiidamental factors controlling these two observations. procedure: Fig. 1 shows the initial step in the fabrication of the specimens. The sieve is shaken so that the fibers fall into a mold with the longitudinal axes of most fibers in the X-Z plane. The fibers are then compressed to a predetermined density, thus forming a "felt", and the necessary amount of matrix metal is added to the top of the felt. The mold is heated, in vacuum or hydrogen, to above the melting point of the matrix metal; the molten metal flows into the felt, and the entire assembly is cooled. This produces a "composite" that is essentially free of voids. A number of composites were prepared in this manner using 1/4-in. kinked lengths of mild steel

Jan 1, 1962

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

By T. Olrog

Dissemination of technical data on developments in rock-blasting techniques in Sweden initially takes place as personal contacts and contacts between companies. In addition to these informal contacts, contacts occur in Sweden in a somewhat more organized form. There exists an informal working group--the Rock Blasting Committee--which consists of a number of personal representatives from various companies that perform rock blasting on a large scale and from firms manufacturing the equipment that is used. This means that people from both mining and construction companies get together, plus the manufacturers of explosives, drill steel, drilling machines, and loading equipment. This working group has, so far, succeeded very well in ignoring the purely commercial interests of the companies concerned. Cooperation in this form was started in the 1940's when the tungsten-carbide drill steel was invented-the group originally concentrated entirely on the development of that product. Their activities have been broadened since that time and now a meeting is held every year, at which practical experiences are reported. Only in the past five years have subjects relating to blasting procedures to avoid rock damage been treated at such meetings. This, of course, does not mean that such techniques had been neglected previously. It does, however, reflect the fact that practice in this field is still under development. Why do we try to be careful about the rock surfaces? Obviously, it is a question of economic evaluation. An even rock surface provides, in certain cases, the conditions for more favorable maintainance costs later on, greater strength, and a diminished risk of slides. The economic connections in this field, however, are neither simple or clear. A well-controlled blasted rock surface limits the need for concrete when you later build the concrete constructions. In this respect, the connections are all the more clear. In certain situations, such as tunnels for hydroeletric power plants, a good rock surface that is not lined is hydraulically more favorable than a more coarsely blasted surface. This permits a gain in the height of fall, but the

Jan 1, 1970

By T. C. Atchison, W. I. Duvall, D. E. Fogelson

Dr. Clark has given an excellent resum6 of the recent theoretical re- search work that has been done on the generation and propagation of stress waves in various types of media.1 Unfortunately the dynamic properties of rock do not fit the assumed properties of the idealized media. As a result, none of the theoretical solutions for the generation of stress waves by applied pressures to interior boundaries of the spherical or cylindrical cavity appear to be completely satisfactory to explain experimental data. This fact does not mean that the theoretical work is in error. It simply means that the appropriate dynamic properties of rock have not been taken into account in the present theoretical derivations. Because of the difficulty of theoretically accounting for the crushing and cracking that takes place when explosives are detonated in spherical or cylindrical cavities, it seems advisable that future theoretical studies should attempt to separate the generation of stress waves from the propagation of stress waves. Perhaps if these two problems are separated, we may be able to solve one of them satisfactorily so that theory and experimental data agree. Dr. Clark's resumé of the research work on scaling and crater formation by point charges is aimed at obtaining a basic understanding of the physical theory of rock breakage, wave generation, and wave propagation. A cursory reading of Dr. Clark's paper shows that there is very little information summarized that can be used by the practicing engineer in the field of blasting. When problems become too difficult to solve theoretically it is always helpful to take the empirical approach and collect experi-

Jan 1, 1967

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Continuous and aligned fiber composites provide the highest possible reinforcement for a polymeric matrix. In particular, the impact resistance is significantly increased in comparison with a low energy absorbed brittle polymer. For this reason, investigations have been carried out with both synthetic and natural fibers as a way to improve the toughness of polymeric composites. Among the natural fibers, ramie was not yet been studied for its reinforcement effect to make tougher polyester composites. Thus, the present work assesses the impact toughness of polyester composites incorporated with different amounts of ramie waste fibers.IntroductionIn most engineering and other technological areas, the use of materials associated with low energy processing conditions is gaining attention for the possible environmental benefits. This offered an incentive towards the substitution of natural renewable and biodegradable materials for the traditional energy intensive synthetic materials [1]. Natural fibers from both origins: animal, such as silk and wool, and vegetable, such as cotton and jute, are typical examples of those environmentally friendly materials. Low cost and highly reduced processing machinery wear are important advantages of the natural fibers over the most common synthetic ones such as glass fiber and nylon. For these reasons, polymeric composites reinforced with natural lignocellulosic fibers have nowadays been the subject of investigation [2,3].The mechanical strength is one important property of lignocellulosic composites to access the possibility of uses like structural materials for building parts such as doors and panels, as well as furniture. In this case, mechanically strong fibers like sisal, jute, curaua and ramie [4-7] are most convenient. Moreover, the relatively low fiber/matrix interfacial shear stress in these composites is associated with higher impact energy. In fact, a greater energy has to be expended for the rupture of a weak interface. The many cracks that are formed by impact tend to branch during the fiber pullout from the matrix [8]. A larger number of cracks correspond to a greater fracture surface and consequently higher toughness."

Jan 1, 2008

By Carville E. Sparks, Rollin Farmin

Edward Thomas (U.S. Bureau of Mines, Washington, D. C.)—This excellent article on an ingenious and successful installation of wooden rock bolts loses much of its effectiveness through an attempt by the authors to establish the general adaptability of this type of support. Possibly because they have only local experience as a guide, they imply erroneously in the first paragraph that the Bureau of Mines has been opposed to wooden bolting, although later in the article reference is made to a Bureau publication on the subject. In 1947 the Bureau of Mines decided to sponsor experiments in roof bolting in coal mines because the experience of the St. Joseph Lead Co. had indicated that this type of roof support appeared to be a roof-fall accident-prevention measure that might be adopted and also effect economies in operating cost. Justification for this belief has been borne out, particularly in coal mining. This program has been carried out under the following general program: 1—The Roof Control Section of the Bureau of Mines has advocated and initiated underground experiments under controlled conditions with many different ideas related to rock bolting since 1947. In no instance has cooperation in developing an idea been refused, no matter how ridiculous it may have seemed at first glance, if it has been requested by a mining company. 2—The Bureau of Mines has no police powers over the selection of roof-support devices and seeks none. 3—At the request of an operator, the Bureau of Mines will make comparative tests on various types of bolts underground and will submit resultant data for the operator's consideration. 4—Wherever possible, the Bureau publicizes successful installations, so that others may benefit from this experience; however, it is careful not to discriminate between manufacturers of bolts or bolt-installation equipment. Unsuccessful experiments probably should also be publicized, but from a practical standpoint it is usually not feasible. In other words, the role of the Roof Control Section of the Bureau is in line with the original purpose for which the Bureau was first organized: to serve industry through gathering, analyzing, and disseminating factual data. It would seem to be logical that the starting point for any experimentation on roof bolts in coal mines should be the time-proved practice of the

Jan 1, 1955

By John B. Pearse

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway Managers determined on and have long applied a test of 1000 pounds falling 101 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails from our most reliable makers, break under a 6 foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 13 1/2 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent, of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. In England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariably

Jan 1, 1873

Geological modelling is a crucial preparatory stage to most facets of the mine planning of an orebody. The process of modelling involves skilled geological interpretation. Recent innovations in computer software and graphics hardware provide many tools which can be used to dramatically improve on manual methods of interpreting orebody data. Geological interpretation can be carried out quickly to produce accurate block models for many orebody attributes, such as grades, and these models can be easily updated locally as exploration and mine development data become available. The speed of the modelling process coupled with the mass storage capabilities of the computer now allows geologists to optimise the geological model or carry more than one model through to the mine planning phase.

Jan 1, 1987

By A F. Idziak

The aim of the present study was an application of coal optical property measurements for analysis of paleostress field existing in fault zones of the Upper Silesian Coal Basin (USCB) during the coalification of organic matter. Measurements of vitrinite reflectance were carried out on coal samples taken near a hanging stope of the Klodnicki fault. Other samples had been taken in vicinity of the Krzyzowicki fault. The Klodnicki fault is one of the main tectonic discontinuities in the northern part of the USCB. It is postulated that its origin is related to the deep-rooted latitudinal discontinuity in crystalline basement of the basin. The Krzyzowicki fault is located in the western part of the USCB where fold tectonic style dominates. Vitrinite, one of the basic components of hard coal is generally considered as optically anisotropic material. Anisotropy of physical properties is induced mainly by stress, which arranges vitrinite structure. Vitrinite anisotropy can be described by an ellipsoidal model called reflectance indicating surface (RIS) which is a geometrical representation of the optical anisotropy tensor. The investigation of the RIS for vitrinite was carried out on coal samples. The apparent maximum and minimum reflectance values measured for a single vitrinite particle were plotted against corresponding bireflectance to construct the reflectance crossplot. Interpretation of this plot yielded the magnitudes of the RIS three principal axes. The data obtained point to differences in optical anisotropy of coal under the study. The coal samples taken from block tectonic zone near the Klodnicki fault had mean reflectance value of less than 0.80 per cent. Their anisotropy coefficients were about 0.1. Optical properties of coal changed from the biaxial positive in the western segment of the fault to the biaxial negative in its eastern part. It suggests that past tectonic stress was greater in the western part of the zone than in the eastern one. Coal originated from a fold tectonic zone at the vicinity of the Krzyzowicki fault has mean reflectance value much greater than from previous region (ÿ1.20 per cent). Its optical anisotropy coefficient is equal to about 0.07. It suggests that paleostress field was more isotropic. The presented study shows the usefulness of coal reflectance measurements in the analysis of paleostress field existing during coalification process.

Jan 1, 2003

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By Henry Howe

1. The purpose of the National Research Council as organized for war purposes is twofold, to stimulate those outside its own personnel to conduct researches of importance for winning the war and to carry on such researches through its personnel to a limited extent. How this is clone is explained in Section 10. "Research" is used here in a very broad sense, including, for instance, inventing and developing mechanical and physical devices. The need of this work arises from the inevitable concentration of most of the governmental war agencies on the production and transportation of war materials of. the types now adopted, as distinguished from devising new kinds of instrumentalities, such as armor, guns, aircraft, and apparatus for detecting, locating, observing, signaling, transporting, and many other military purposes. But it is important that we should devise new agencies. The war came near being won by an invention, the submarine, and its course has been affected greatly by two other inventions, tanks and aircraft. In spite of our numerical superiority victory may well be snatched from us by an invention, if we allow Germany to outstrip us in inventing. Hence the importance of the Council's work in mobilizing and organizing the services of the patriotic civilian experts throughout the country, so as to bring their powers to bear on important war problems and on inventing war devices, as an adjunct to the development work of the regular governmental bodies. 2. Status of the Council.-Though President Wilson's request caused the Council to be created by the National Academy of Sciences under its congressional charter in 1916; though his executive order of May 11, 1918, directs the heads of "Governmental departments immediately concerned" to "continue to co-operate with it in every way that may be required;" and though the Government has contributed largely to its financial support (Section 12, page 10), it is not a department of the Government but an independent research body, aiming to evolve the necessary mechanism for the novel work of systematic stimulation and guidance of research. Thus the Government, which instigated the creation of the Council, recognizes and collaborates with it, and in part supports it. The Council acts moreover as the Department of Science and Research of the Council of National Defense.

Jan 12, 1918

By W. C. Schroeder

During the post-war period, and particularly during the past few years, coal production has been maintained at a reasonably constant level. This is in contrast to the greatly expanded demand for oil and natural gas. Certain markets for coal, such as the railroad and for home heating, have tended to decrease, but this decline has been offset by an increase in demand for other uses, particularly for electric power. Since the United States has very large reserves of coal and relatively limited reserves of natural gas and oil, from the conservation viewpoint, it would be better if the increased demand were to fall more heavily on coal. Where coal has lost certain markets, the decision has not always been made on the basis of price, and, in fact, in many instances, the markets have been lost where coal could show a price advantage. There are various reasons for this situation but it can be attributed in the main to the preference of certain consumers for the convenience offered by liquid and gaseous fuels. In the production of chemicals such as benzene, phenol, or ammonia, coal still plays an important role. As co-products from coke-oven operations, a wide variety of aromatic chemicals are available. In recent years, however, the production has not been sufficient to supply the demand, and it is not profitable to build coke ovens to make chemicals unless there is a market for the coke as well. As a result, the petroleum industry is beginning to take a stronger part in the production of aromatic chemicals. Natural gas has almost displaced the coke-oven water-gas machine for the production of hydrogen for the synthesis of ammonia, as well as for the synthesis of methyl alcohol and other oxygenated compounds. This information is not new and is given here only as a basis for the discussion of the broad significance of the development of the gasification process. It is clear that if coal is to regain some of its old fuel markets, as well as to maintain a position in the field of chemical synthesis, processes must be available for converting coal to the type of fuel the customer wants, and for a cheap method of furnishing gaseous raw material to the chemical industry. The operation of coke ovens and water-gas machines is not the answer to this problem for at least two important reasons: (1) the limited supply and relatively high price of good coking coals, and (2) the relatively high costs of the combined operations of coking and manufacture of water gas.

Jan 1, 1953

By G. S. Hume

IN. THE autumn of 1922, British Petroleums Ltd. found oil of 14° Baumé in a sand 17 ft. thick in its. No. 2 well at Wainwright, 120 miles southeast of Edmonton. This greatly encouraged drilling in the Wainwright-Irma area and this past summer several wells were started, three of which are now completed and the others still being drilled. Of the three completed, No. 4 British Petroleums contains oil; No. 3 British Petroleums gave a show of oil but so far has not given much hope, of becoming a commercial producer; and No. 1 Maple Leaf Co., as now finished, is a. gas well with a daily flow of gas of about 2,500,000 cu. ft. at a closed pressure of 700 lb. An oil sand is reported to have been encountered below the producing gas horizon in the Maple Leaf well but has not been tested. Operations on this well have been suspended for the winter. The Geological Survey of Canada this past summer undertook a geological investigation of this area with the object of defining the structures with which the oil and gas are associated. The structure underlying this portion of the plains was supposed to be a terrace with the western edge dipping into the Alberta syncline and with a monoclinal structure to the east. By accurate leveling on known geological horizons on this terrace, a number of gentle folds were located and -it is in these folds that the oil and gas are found. At the British Petroleums Nos. 2 and 4 oil wells, the western flank of the fold has a gentle dip of only a few feet to the mile to the southwest whereas the strata on the eastern flank dip to the northeast about 40 ft. in ½ mile, the strike of the fold being northwest and southeast. How far oil will be found down the gentle southwest dip is unknown but probably the productive part of the fold will not exceed 1 mile in width, and possibly less. No. 3 British Petroleums well is on the strike of the fold 1 mile southeast of the two oil wells. The sand that was productive in Nos. 2 and 4 wells was not present in this well or, if present, was very thin and unproductive. Two other sand horizons, however, were encountered. The upper of these

Jan 3, 1925

Gerald Sherman, Bisbee, Ariz. (written discussion*) .—The fact that, after a change in the hours of labor, as much work is found to be done in 8 hr. as was accomplished in 10, probably results from the more rigid examination of operating methods that is made when the management faces new and more difficult conditions. Although A better working pace will prevail, most of the gain will result from economies of plan and only a part of it from the improved effciency of labor. The Iabor of shoveling is so severe that it may be easily believed that a working period of less than 7 hr. will give maximum results, but there arc many other occupations about a mine in which this is not true, and in which the rate of accomplishment is in proportion to the time employed, up to 9 or 10 hours. Mr. Harley's study of shoveling has becn thorough, and demonstrates the benefit of investigation and education even in such simple work, but his reference to methods of payment opens a subject even more important in mine management. The efficiency of labor may be excellent, but unless a method of equitable payment accompanies it, the result will be only temporary. With strict but sympathetic supervision, a good average day's work can be obtained; but with the exception of those unusual men who cannot be restrained from working to their limit, an average daily wage does not bring out the remarkable performance of which many men are capable. There is also a considerable variation in the average amount accomplished, dependent on the supply of Iabor. This can readily be shown by any labor record that covers several periods of shortage or superabundance of labor. An increase in the daily wage in the time of labor shortage does not necessarily bring out an increased day's work; there is usuaIly a decrease in labor efficiency at such times regardless of the wage, whenever a daily rate is used. Rewards to individuals for exceptional performance appearing as an increased rate of pay cannot be made in a large organization without bad feeling. In a small organization, an individual's ability may be so well recognized that different rates of pay can be applied. Exceptional work can only be obtained by a method of payment based on the valuable results accomplished. As a basis for such payment, an

Jan 1, 1920

THE 144th* meeting of the American Institute of Mining and Metallurgical Engineers was held in New York, Feb. 18 to 21, 1935. It consisted of the annual business meeting, 45 technical sessions at which 216 papers were presented (approximately the same number of sessions and papers as at the previous annual meeting), two sessions of the Board of Directors, three meetings of Section delegates, two formal lectures and two addresses, luncheon Monday, Tuesday and Wednesday for members and guests, six group dinners and eight group luncheons, ten committee meetings, the annual reception and dinner dance, an informal dance, a smoker-dinner and the annual meeting of the Woman's Auxiliary. Attendance was generally greater than for the two preceding meetings; the statistics follow (figures are in the order 1935-1934-1933); total registration, 1609-1534-1475; dinner dance, 577-543-426; dinner-smoker, 490-425-394; informal dance, 279-295-250; women's registration, 179-160-133; general luncheons, 1132-1034-734. The Coal Division held two general sessions on Monday and a symposium on coal-mine ventilation on Tuesday morning. The Committee on Bituminous Planning, Edward Steidle, chairman, presented a report at the Monday morning session. C. B. Huntress, President of Appalachian Coals, Inc., was the principal speaker at the luncheon on Monday, at which Eli T. Conner, Chairman of the Division, presided. Mr. Huntress was preceded by Howard N. Eavenson, President of the Institute, who spoke briefly. The Sectional Committee on Classification of Coal met Wednesday afternoon. A feature of the meeting concerning three Divisions-Iron and Steel, Institute of Metals, Petroleum-was the symposium on Use of Metals in the Petroleum Industry, Thursday morning and afternoon. Five of the papers presented at this symposium have been published in METALS TECHNOLOGY'. Another feature, of general interest, was the Tuesday morning session in the Auditorium, devoted to Federal Government and Mineral Industries. Dr. C. K. Leith delivered the principal address, on "A, Mineral Policy for the United. States." . The Institute of Metals Division held technical sessions Tuesday afternoon and Wednesday. morning and afternoon and on Thursday

Jan 1, 1936

By C. A. Wright

Since the adoption by the U. S. Bureau of Standards several years ago of specifications for standard 100- and 200-mesh sieves, frequent requests have been received that this Bureau test and certify sieves of other sizes than these. With a view to the adoption of a series of standard testing sieves which might be of use to all industries making fineness tests, this Bureau for two years has been studying the question of such a standard screen scale. Various scales that have been proposed were considered, and information was sought of representative firms in the various industries interested as to their requirements. Manufacturers of sieves have also been consulted as to the desirability of different screen scales and the practicability of their manufacture. As a result of this study of the question, a conference was called at the Bureau of Standards, Apr. 20, 1916, of representatives of various committees of the American Society for Testing Materials, American Society of Civil Engineers, American Institute of Mining Engineers, American Foundrymen's Association, Mining and Metallurgical Society of America, American Water Works Association, American Institute of Metals and the American Spice Trade Association; also representatives of the Committee of Revision of the U. S. Pharmacopæia, the U. S. Geological Survey, the U. S. Bureau of Mines, the U. S. Office of Public Roads and Rural Engineering, the U. S. Office of Grain Standardization and the U. S. Bureau of Standards; also representatives of a number of private firms engaged in industries in which sieves are used, such as the glass, the drug milling, the abrasive, the asphalt, the mining, the spice, the chemical, and the graphite industries; also representatives of the firms in this country manufacturing wire cloth and sieves. This Conference, after considering the various screen scales either proposed or now in use, adopted as a Standard Screen Scale that given in Table 1, and recommends that it be adopted generally by scientific,

Jan 1, 1918

By W Stange

Assessing the risks in a mining project is a key aspect of project evaluation. This is an exacting and demanding task because of the complexity due to the need to deal with uncertainty over long time periods. The way risks are assessed and managed is critical to the long-term success of the projects and the business. Discounted cash flow (DCF) analysis is commonly used for project and risk evaluation. A discount rate is selected that accounts for uncertainties in the cash flows. However, it is difficult to determine an appropriate discount rate due to the large number of factors that need to be considered and the complex relationships between risk sources. Using a proven framework, ævalue at riskÆ (VaR), this paper proposes to rigorously model and quantify ærisk at sourceÆ. The approach was first employed to assess financial market risks and is now widely used in the banking sector for risk assessment. In project evaluation, all risk sources are identified and estimated separately to ensure the overall project risk is quantified accurately. A bottom-up approach has been proposed. Estimates are first carried out for risk factors at the bottom of the project structure. The assessment is then applied at increasingly higher levels until the overall project risk is estimated. Value at risk is a versatile methodology and can be used in a local or integrated manner. The final value is objective and the calculation steps can be easily justified and followed. Four case studies have been included to illustrate how the proposed approach can assist management in decision-making.

Jan 1, 2009

By N. S. Keith

It seems proper, before describing the plant which has been erected in Rome, N. Y., for the purpose of demonstrating the practicability of my process of refining and desilverizing lead by electrolysis, to state in a few words the principles that govern the process. They are well known to those who have studied electrical science, and to the practical electro-platers of the country, and are briefly these: If we take a plate, or other form, of metal (impure lead in this case), and immerse it in a bath consisting of a solution of the main metal (that which contains the impurities), and also immerse another plate, which shall be a conductor of electricity, in the bath, but separated from the first by the solution, and connect the former plate with the positive pole of the source of electricity, and the other plate with the negative pole, an action will go on in this bath which is called electrolysis. There is first a decomposition of the solution constituting the bath ; then a solution of the metal at the positive pole (called the anode), and a deposition upon the other plate connected with the negative pole. which plate is technically called the cathode. If the bath is properly constituted, and the current of electricity which is passed through the bath is of the proper strength and electro-motive force, the dissolution of the anode and the deposition of the metal upon the cathode will be exactly equivalent. The analysis and synthesis are opposite and equal. If, on the other hand, this solution (called an electrolyte) be not properly constituted, decomposition will go on, but there will be these effects: a superoxidation at the anode and a liberation of free hydrogen at the cathode, which free hydrogen escapes finally in bubbles through the liquid to the surface, and into the atmosphere. In the electrolytic treatment of metals simply for their purification and recovery, it is

Jan 1, 1885

By Norman J. Gibbs, John Sroka

INTRODUCTION At the point a company decides to begin mine development and wishes to convince lending institutions that the proposed operation will return their borrowed funds, plus interest, over the terms of the loan, communications between lender and borrower are crucial. The importance of the mine feasibility presentation should not be underplayed, especially as new projects continue to increase in size, complexity, and cost. While the content and emphasis of a report to the lender will vary according to the particular project and type of debt financing sought, there is a general base of information upon which all such studies are built. THE PROJECT'S TECHNICAL ASPECTS Here, the object is to satisfy the lender that he will not be unduly exposed to technical risks as a result of the physical scope of the project. Reserves The feasibility report submitted to financial institutions should include an adequate description of the geologic setting, mineralogy, ore types, and reserves broken down into such recognized categories as proven/probable/possible or measured/indicated/inferred. Rather than a bald statement of reserves, lenders prefer to have detailed information on: History of exploration Drilling, both percussion and core, with core recovery, drill hole spacing, analyses, and continuity of mineralization Bulk sampling, with core assay comparisons Overburden, with stripping ratios Specific methodology of reserve calculation, and Geologic reserves vs. mineable reserves. As a rule of thumb, a lender would prefer to see that reserves in the proven class alone are sufficient to support operations at the design rates until the borrowed funds are repaid. (See also Schreiber above in this Chapter.) Mining The rationale for adoption of a particular mining technique should be presented as well as descriptions and justifications for: Preproduction development Preliminary mine plan, with forecasts of grades and material movements Geotechnical test work which influenced decisions Mining recoveries and efficiencies Major equipment, with type, model, rating life, spares, replacement schedules, utilization, and productivity Manpower requirements and work schedules Design assumptions Ore stockpiling and blending Environmental requirements, and Waste disposal Processing If a new ore body is to be developed or a new process used, it is important to provide details of test work, scale up, and extrapolation factors. A basic process description with a summary of the studies which justify the intended processing route should be included with the following data:

Jan 1, 1985