Search Documents

By R. H. Jacoby, M. J. Rzasa

Experimental equilibrium vaporization ratios were obtained for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in natural gas-condensate systems. Two different overall mixture compositions were investigated over the pressure range 500 to 4,000 psia at 100°, 150°, and 200 °F. Partial phase diagrams of the mixtures were obtained; one of these showed a critical point at 204°F and 3,875 psia. These and earlier data' were compared with the Kellogg correlation' at! 100°F and 1,000 psia. INTRODUCTION The authors' have presented equilibrium vaporization ratios for nitrogen, methane, carbon dioxide, ethane, and hydrogen sulfide in complex mixtures, such as natural gas-crude oil and natural gas-absorber oil. Since mixtures of the natural gas-condensate type also occur widely in petroleum reservoirs and often contain the non-hydrocarbons mentioned, it would be useful to have appropriate K data for calculating equilibrium vaporization conditions. Roland, Smith, and Kave-ler' obtained K's for methane and the light hydrocarbons in gas-condensate mixtures; and Poettmann and Katz3 obtained K's for carbon dioxide in a gas-condensate system. The data presented in this paper extend this coverage to include K's for nitrogen and hydrogen sulfide and phase diagrams for the experimental mixtures. EXPERIMENTAL WORK The equipment and experimental procedure was essentially as described previously, except for analysis of the vapor samples. The vapor sample bombs were filled at the pressure and temperature of the run. Immediately after sampling, a portion of this sample was flushed from the bomb into a 650 cc glass bulb, filling it to near atmospheric pressure. The sample in the glass bulb was then analyzed by the mass spectrometer. Some checks were made on this analytical procedure to find the accuracy of measurement of the C + content of the vapor samples. The modifications tried were complete fractionation of the vapor sample and the use of several liquids (depropanized condensate and retrograde liquid from several vapor samples) as calibrating materials for the mass spectrometer. The results obtained from these various checks differed by about 10 per cent relative and this is believed to be the order of accuracy of the vapor C+ concentrations.

Jan 1, 1953

By Frank R. Hunter

Introduction Scope of Work This paper represents the results of an investigation of the presence, amounts, and degree of concentration of heavy minerals found in the pulp of the phosphate flotation plant at Peace Valley, Fla., which is operated by the International Minerals and chemical Corporation of Chicago. In this paper, heavy minerals are those, excepting collophane, that sink in acetylene tetrabromide with a specific gravity of 2.95. Percentages of heavy minerals at several points of the flowsheet and the species of minerals have been determined. Some information as to the screen size of the minerals has been acquired. Previous Work All previous published reports or investigations of the deposits of heavy minerals in Florida have been limited to present beach sands. The mining operations conducted by the Humphreys Gold Corp. about seven miles east of Jacksonville along an ancient shore line have been described in trade journals, but descriptions of the minerals have been lacking. Commercial grades of ilmenite, zircon, and rutile are produced on a large scale. Papers have been published on heavy minerals found on the Florida beaches.1-6 Location "International's" Peace Valley flotation plant is in south-central Polk County, Fla. about eight miles south of Bartow and along the Atlantic Coast Line Railroad. The mine surrounds the plant and includes about 1500 acres of the phosphatic lands in this area. Geology General Setting All of the rock underlying the area is almost horizontal. The oldest bed exposed is part of the Hawthorn phosphatic limestone of Miocene age. This outcrops in the stream bed of the Peace River about one mile east of the plant. Elsewhere the Hawthorn is covered except where it has been exposed by mining operations. The Bone Valley formation of Pliocene age, which is the phosphatic stratum extensively mined in this area, unconforma-bly overlies the Hawthorn. Resting unconformably upon the Bone Valley formation are Pleistocene (?) terrace deposits of unconsolidated quartz sand which comprise the overburden of the phosphate ore. Stratigraphy Hawthorn formation: "Bedrock" of the pebble phosphate deposits is a cream to white colored, sandy, dense limestone containing varying amounts of small grains and nodules of collophane. The upper surface of the formation is undulating and irregular showing evidence of former

Jan 1, 1949

By Donald B. Gillies

The fundamentals of human nature don't change much from generation to generation, or even from century to century. Except for the spur of necessity and the lure of reward and ad venture, few of us would bestir ourselves unduly. The general welfare has little appeal to the average individual. Its promotion comes about mainly as a by-product to individual efforts directed at more personal benefits and satisfactions. In discussing incentives for the mining industry, we really are talking about incentives for people who devote their energies and resources to mining. The vigorous and productive mining industry as we have known it was the product of the varied incentives we have known in the past: the lure of great financial reward if you struck it rich; the thrill of romance and adventure in the search for mineral wealth, usually along the frontiers 'of civilization; the satisfaction of developing a great, productive enterprise by the application of skill, courage, and determination in the face of obstacles. Back of the prospector and engineer were other venturesome persons willing to take a flyer with their savings in a grubstake, or in stock in a promising mining venture, hoping for large returns, but reconciled to take a loss and try again with the next opportunity. It is free enterprise-a chance for high profits, but a chance also of total loss-that created the great mining industry of this country and of the world. Free enterprise has given us, in the United States, the greatest productive system in the world, the highest standard of living, the most abundant life. The lure of gold-whether from the ground or merely incidental to the discovery and development of our mineral resources-pushed our frontiers westward across the country and northward into Canada and Alaska far in advance of the staid course of agriculture and commerce. No one guaranteed success to our forebears as they risked life and fortune in developing a new country. Self-reliance was the backbone of our economic and spiritual Progress and achievements. Our neighbors had little time to spare from their own problems. And though there was a willingness among the pioneers to help one another, they didn't lean too much on one another.

Jan 5, 1950

By Wilbur Nelson

ALL of our accounts of the discovery of copper ore at Ducktown, Tenn., state that the discovery was made in August, 1843, yet it would appear that samples of copper from this district were found by the Spanish explorer, DeSoto, when he wandered into Southern Tennessee, in 1539, in his four years of exploration through the Southern States. The following quotation is taken from his diary: "Towards the north there was a province named Chisca; and that there was a melting of copper, and of another metall of the same colour, save that it was finer, and of a farre more perfect colour, and farre better to the sight, and that they used it not so much, because it was softer. And the selfe same thing was told the governor in Cutifa-Chiqui, where we saw some little hatchets of copper, which were said to have a mixture of gold. But in that part of the country it was not well peopled; and they said there were mountains, which the horses could not passe; and for that cause, the governor would not goe from Cutifa-Chiqui directly quicker." DeSoto sent two of his company to try to find these mines, but after five days' wandering through the mountains they returned, stating that their guides had become lost. Although the Ducktown area may have been known to the ancient Indians, it was not until August, 1843, when a Mr. Lemmons, who was panning for gold on Potato Creek, in the Ducktown basin, found some reddish-brown decomposed rock, which he supposed to be gold, that the copper deposits were actually discovered. His disgust on finding that this yellow metal. was not gold was so great that he did not. try to develop his find. In March, 1847, B. C. Dugger erected an iron forge at this same place, but was unable to work the iron as it contained so much copper that on cooling it would break to pieces. The finding of copper in the iron ore by Mr. Dugger led to further explorations; and in April, of the same year, A. J. Weaver, who was passing through that country, told the people that the black rocks they had dug out were rich copper ore. Mr. Weaver began the first mining in this district.

Jan 10, 1924

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

The stabilization of a gravel road with soil is a method of treatment developed in recent years by the United States Bureau of Public Roads for the purpose of binding the constituents together better, and maintaining a more durable surface. The process consists in adding to the gravel or crushed stone and sand, a soil mortar, so-called, of fine sand, silt and clay, mixed in the proper proportions. The coarse gravel and sand supply structural strength and hardness; the fine sand adds embedment support to the coarse sand; the silt acts as a filler to prevent the granular particles from rocking; while the clay serves not only as a binder but also provides pores minute enough to cause connecting moisture films which are supposed to have high cohesive properties'. It will be recognized that the clay is an important ingredient both when wet and dry, and should not show excessive expansion when wet, nor correspondingly high shrinkage in drying, as otherwise there is danger of unseating the nonplastie particles. Such a stabilized road, although an improvement on one with a floating surface, will in course of time be subject to wear, and become dusty when the clay dries out and breaks up. It has been found that if some salts are added to the road mixture they tend to maintain the soil moisture and prevent dustiness of the road or raveling of the road surface. In addition to this, it is claimed that these dissolved salts cause a thinning of the moisture films on the particles, thus permitting greater compaction of the road mixture, and thereby increasing its density. This fact can be proved by noting the increased compaction which a road mixture shows when certain salts are added to the soil water. Since certain chemical substances such as sodium chloride are electrolytes, the question arises whether they cannot have wine effect on the qualities of the clay in the soil mortar, and perhaps improve them. In view of the fact that certain salts seem to exert a favorable effeet on the road mixture it is desirable that they he held in the road soil as long a time as possible.

Jan 1, 1938

By Robert Linton

IN 1898, Joseph L. Giroux and J. A. Snedaker organized the Pilot Knob Copper Co. and began developing the Pilot Knob mine at Kimberly, Nev., for high-grade copper ores, carrying good gold and silver values that the formation had disclosed. At that time the nearest railroad was over 150 mi. distant. The high-grade ores did not prove to be extensive at this point-at least to the depth. (240 ft.) to which the work was carried-but development of neighboring claims indicated extensive deposits of sulfide porphyry ore of concentrating grade lying at shallow depth, and deeper deposits of direct-smelting oxidized ores occurring in limestone near the limestone-porphyry contact. The properties passed through the hands of several organizations, with only meager development, until acquired in 1913 by Consolidated Coppermines Co., whose holdings now comprise 3480 acres of mining claims in the Robinson district. Since that time development has been prosecuted more actively; and for the purpose of determining the most efficient and economical method of treating the ores, considerable testing work has been done during the past three years, both in the laboratory and in actual mill operations. At first, the shipments were of ore high enough in grade to be profitable even with the long wagon hauls to the railroad and prevailing freight and smelting charges. In 1905, a blast furnace and a concentrator were erected at Kimberly. On account of insufficient ore supply, the blast furnace was never blown in and later was dismantled. The concentrator as originally equipped wag operated for only about two months, both because the ore supply was not sufficient and because gravity concentration did not yield satisfactory extraction. The location and arrangement of the mill further entailed high operating costs. In 1908, the Nevada Consolidated Copper Co. began to mill successfully, on a large scale, its sulfide porphyry ores, which are similar in character to the adjacent Coppermines ores. After that time, all of the ores and concentrates produced by Coppermines Company were

Jan 8, 1920

By B. Bryan

The tank car price of gasoline today is controlled by oil in the ground, rather than by stocks of gasoline or methods of refining. Previous to the commercial cracking of fuel oil, there was a normal and continuous relation between gasoline stocks, consumption and prices. From the beginning of the new cracking era in 1923 to the summer of 1926 there was a changing relationship, growing toward a correlation between the potential gasoline in storage and the price of gasoline. Since the development of large reserves of shutin production in Wyoming, California, Seminole, West Texas and Venezuela, the relationship between stocks of gasoline and gasoline prices has disappeared. The extreme depression of the Group 3 price can only be accounted for by oil which is not being produced but which we fear may be produced at any time. In Fig. 1, the curve of gasoline stocks is simply stocks of finished gasoline. The curve of potential gasoline is made by taking 40 per cent. of all stocks except gasoline, kerosene and lubricants, adding to that stocks of finished gasoline and dividing the sum by total gasoline con-sumption to get the months' supply of gasoline at the current rate of consumption. The price curve is the lower figure given by the National Petroleum News for the first quoted date of each month, with the price scale reversed. Stocks of potential gasoline have decrrased from 17 months' supply at the peak of 1924 to a low of 7 months' supply during the past summer, yet the low immediately precedes the lowest price for gasoline since it was a waste product. The tendency of the price curve to parallel the curve of potential supply is quite pronounced until the summer of 1926, since which time they have abruptly separated. The curve of gasolinct stocks is equally remarkable in relation to price when it is considered that total consumption for the year 1927 is almost exactly twice that of 1924. Clearly a new factor has been introduced. There is no possible factor to account for this distortion except known reserves of oil in ground storage, and therefore, until such time as the Bureau of Mines or the

Jan 1, 1928

By E. M. Boatman, S. J. Pirson, R. L. Nettle

More than a decade ago some theoretically derived relationships were proposed that permitted the prediction of the relative ability of reservoir fluids (oil, gas, water) to flow simultaneously within the porous structure of rocks. While many successful predictions of fluid-flow ratios from wells have been made from electric logs, the theoretical deductions have not been subjected to laboratory verifications. For the relative permeability to liquid and gas, simultaneous flow of water and air was used, employing the familiar external-gas-drive technique. While in the process or water desaturation, the resistivities of the test cores (Woodbine sand) were measured. Their permeabilities varied from 10 to 280 md. The laboratory results indicated the need for changing the values of exponents in the theoretically derived formulas, whereas the form of the functions of resistivities and saturations remained as derived by theory. For the relative permeability to oil and water, the three-core dynamic technique was used on six cores. In this case it was found that the formulas were valid with but slight modification as derived by theory, to a sufficient degree of accuracy for engineering use and for well productivity prediction from electric logs. INTRODUCTION Conventional quantitative well log interpretation generally stops after reasonable values for formation porosities and water saturations have been established. Yet such in formation is insufficient to predict either the outcome or the desirability of well tests and completion, let alone the economic aspect of producing oil- and gas-bearing sections which might have been established by conventional log analysis. To give an engineering answer to such questions, it is necessary to predict the expected fluid flow ratios, the productivity index and the ultimate recovery from potentially productive wells. This problem requires in part for its solution a determination of the relative permeability characteristics of the potentially producing formations, both to oil (or water) and gas, and to oil and water.

Jan 1, 1965

By A. T. Peters

DURING an investigation concerning the use of large nozzles for pouring of low-carbon rimming steels, the practical details of which were reported elsewhere, it was noticed that increases of nozzle sizes were generally followed by improvements of slab surface quality. It is the purpose of this note to present the data available and some tentative opinions about this phenomenon. The problem of correlating pouring rates with the metallurgical performance of steels is complicated by several factors. The two most important are; 1) Variations of the steel pouring rate throughout a pour, these being due to the nozzle erosion, which enlarges the bore area, and the dropping ferrostatic pressure in the ladle. The pouring rate is lowest towards the end of a heat when the ladle is nearly empty. 2) Variations in the ingot pouring time due to the different ingot weights poured. Consequently, the use of the average pouring rate of a heat may not be exact, but in large-scale production it is not practical to treat ingots separately according to their pouring rates. The variations of ingot weights and sizes may be overcome by considering the rate of rise of steel in the mold. Hence, the average rate of filling of molds throughout the pour of a heat, inches per second, will be used in this note. Every ingot rolled at Inland is rated at the blooming mills prior to hot machine scarfing as being good, fair, or poor for cracks, scabs, and checking. The latter term refers to the network of breaks or lines associated with overheating or burning in the soaking pits. It is also known that thin-skinned steel is prone to show this defect if the subsurface blowholes are exposed during reheating or rolling. The experiences with the surface quality of slabs rolled from ingots poured at different rates are presented in Fig. 1. The data represent nearly 11,000 ingots. It appears that all three types of defects are in-

Jan 1, 1960

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

By Sonia Helle, Ursula E. D. Kelm

"From a metallurgical point of view, acid leaching of oxide zone copper ore is considered in the first place in terms of ore grade, whole rock mineralogy, rock granulometry, crushed aggregate size distribution, porosity, permeability and corresponding fluid flow characteristics. Despite exhaustive physicochemical and general mineralogical characterization, drops in copper recovery occur and are often attributed to and “unquantified mineralogical misbehaviour” of the gangue phases. This study establishes an experimental link to monitor and quantify the chemical interaction of chrysocolla, malachite and atacamite with reactive gangue phases.Laboratory-scale sulphuric acid (15%) leaching in small columns is carried out using a synthetic rock composed of 57% quartz, 1% ore phase, and 42% reactive gangue. Gangue phases were selected to represent mineralogy found in argillic, advanced argillic, and propylitic alteration zones. Exotic copper ores of Codelco Norte (in particular Mina Sur) served as model for the modal distribution of mineral phases. Natural reactive gangue phases (<200 Tyler mesh) were chosen as pure as possible: Saz-1 and Swy-1 montmorillonites, KGa-1B and KGa-2 kaolinites (all Clay Mineral Society, USA, Source Clays) Nau-2 nontronite, Imt-1 illite (both Clay Mineral Society Special Clays) and Chilean mordenite, laumontite and bentonite. Ore phases are: mineraloid chrysocolla from Radomiro Tomic (Codelco Norte), reagent grade malachite and a purpose synthesized atacamite-paratacamite mixture. Complete chemical, physicochemical and mineralogical characterizations were carried out for ore and gangue phases.The following observations hold for samples with and without mineralization: Smectite-rich gangue increased up to 75% in volume. Once wet, air-filled vesicles formed due to the rapid sealing effect of overlying smectite in the column. No volume change occurred for illite, mordenite and kaolinite gangues. For kaolinite mixtures acid puddles formed on top of the column during initial leaching due to the delamination and barrier formation of this phyllosilicate. Fluid recovery was <60% for expandable phases and reached up to 80% for non-expandable mixtures. These observations confirm the very low extractions obtained in ore with a combined smectite – kaolinite gangue for Mina Sur. The most important mineralogical changes observed in the solid residues are: reduction of basal smectite phase reflections (XRD), and slight loss of illite intensities. This is also reflected in the major element composition of the residues, which demonstrate a loss of Mg, Mn, Ca, Na, K followed by Fe, Al and Si; with their proportions depending on the starting materials. Furthermore, alunogen and meta-alunogen formed, with related phases coquimbite (illite) and godichite (nontronite) also depending on gangue mineral chemistry. For laumontite samples, meta-alunogen and alunogen precipitated from the leachate."

Jan 1, 2003

By P. Lindstrom

Retreat mining, using yielding steel friction props, over a 7-year period has been successful at a uranium mine operated by Hecla Mining Co. in southeast Utah. The support system allows good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered. Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths. The Radon mine was one of the first American metal mines to use yielding steel props for supporting the relaxed core of the pressure arch which is induced by retreating longwall mining. Full caving was induced. After more than 7 years of stoping experience, the method has proved very satisfactory for the conditions encountered. The mine and method have been described in references listed in the bibliography. U.S. Bureau of Mines Information Circular 8004 by Wilbert Dare and Philip Lindstrom gives the most information. Stoping experience at this mine indicates that there are many advantages to be gained by using yielding supports; such as in safety, timber cost, roof control, ventilation, ore dilution, and low cost per pound of metal produced. Subsidence measurements show that the surface will rise rather than slump in some areas over the mine. This appears to be an unusual observation and is presented as a new development in subsidence studies. The Radon mine is located 35 miles southeast of Moab, Utah in the north end of the Big Indian mining district in San Juan County. Hecla Mining Co. operated the mine from early 1955 to early 1964 through an operating agreement with Federal Resources, Inc. Development consisted of a 3-compartment, 690-ft shaft, 4 main levels driven on the ore horizon and a haulage level below the ore. Evaluation of physical and economic factors showed that this flat-dipping ore occurrence could be mined by a low-cost coal mining method. The value of the deposit was high and unusual premiums were possible by clean mining. Complete extraction without loss of ore pillars, minimum ore dilution and high production per man were obtained by longwall mining. The principle of working under the relaxed core of

Jan 1, 1964

By Albert R. Ledoux

In Great Britain all analytical chemists are styled assayers, but in the United states a slight distinction is made, assayers being considered those analytical chemists who have chiefly to do with the determination of the precious metals. There have grown up around the assayers of precious metals a number of customs and traditions which, as a rule, do not fetter American chemists when called upon to determine the composition or constituents of any samples submitted to them for analysis. In Great Britain, on the other hand, trade-customs even go to the extent of enforcing the employment of an admittedly erroneous atomic weight in certain alkali-determinations. If the American chemist is asked to determine the amount of lime in a water, potash in an alkali, or silica in an ore, the owner of the sample does not presume to suggest what method he shall employ, nor does he question his report on the ground that he should employ another method. But even in America it is different with the assayer. Unfortunately for the guild, as well as for those who have to base business operations on the reports of assayers, customs and traditions as well as divergent interests seek to circumscribe him in his choice of method and sometimes dictate how he shall perform his operations. This was true at one time of copper, which to-day in England is still determined by the so-called Cornish fire-assay, an attempt to imitate in the laboratory the various metallurgical operations in the smelting-works; but nowhere in this country is the assayer forced to employ any particular method for determining copper so long as his certificate indicates the true total percentage of copper in the sample. It is true that both buyers and sellers demand use of the electrolytic method, but only because it is the most accurate. In America the trade accepts the assayer&apos;s statement as final, and makes

Jan 1, 1895

By M. Hashemzadeh

The efficiency of water use is a top priority for the global minerals industry, especially in regions with limited freshwater supplies. In these areas, the freshwater shortage has prompted mining companies to search for alternatives to freshwater sources. Seawater has been proven to be a potential water source for mineral beneficiation and metal extraction processes. This study compares chalcocite leaching behavior with ferric chloride to that with cupric chloride. We carried out leaching tests with a highly pure chalcocite sample in jacketed reactors under fully controlled pH and solution potential. The effect of chloride concentration, oxidant concentration, and temperature on copper extraction was quantified in both cupric and ferric chloride systems. In the ferric chloride system, increasing ferric concentration showed a positive effect on the first stage of chalcocite leaching. In the second stage, increasing temperature markedly enhanced copper extraction. In the cupric chloride system, chloride concentration presented a considerable effect on both the first and second stages of leaching, while temperature had a remarkable effect only on the second stage. The findings of this study would be beneficial to mine operations aiming to replace fresh water with seawater for heap leaching of chalcocite. INTRODUCTION Mineral processing operations/plants are normally operated adjacent to mines which are often located in remote and arid area, such as northern Chile, southern Peru and Australia with limited access to fresh water (Liu, Moran, & Vink, 2011, 2013). Water scarcity in these areas has prompted mining companies to invest in sustainable technologies to reduce the water use and/or increase the water use efficiency. One of the current sustainable approaches in mineral processing operations is to replace fresh water with seawater. Seawater is now being increasingly used for mineral beneficiation and metal extraction processes (Hernández et al., 2015). Another application of seawater could be for heap leaching of copper secondary sulfides, mainly chalcocite. However, the high concentration of chloride ion in seawater may significantly affect leaching kinetics of copper sulfide concentrates and ores (Watling et al., 2014). Therefore, it is essential to develop a fundamental understanding of the leaching of chalcocite in chloride media.

Jan 1, 2019

By Patrick Andrieux

Numerous rock blasting design methodologies have been developed over the years, relating either to the primary objectives of blasting, such as the size distribution of the blasted material, or to its undesirable side effects, such as damage to the remaining rock mass. All existing methodologies, while of use, do have serious shortcomings. The question remains whether further improvements can be achieved in the field of practical rock blasting engineering. One approach that seems to hold promise is the relatively new matrix-based rock engineering systems (RES) methodology. It has been conceptually demonstrated that RES could be efficiently adapted to blasting. A brief overview of rock blasting design techniques and their main shortcomings is followed by the basic concepts governing rock engineering systems and a discussion on their pertinence to blasting. The paper concludes with a review of current efforts to develop a useful practical blast design tool using RES. SOMMAIRE Le potentiel d?application des systèmes d?ingénierie du roc aux tirs à l?explosif. De nombreuses méthodologies de conception d?abattage du roc à l?explosif ont été développées au cours des années, qui ont adressé soit les principaux objectifs des tirs, comme par exemple la granulométrie du matériel dynamité, soit ses effets secondaires indésirables, tels les dommages au massif rocheux. Toutes les méthodes existantes fonctionnent dans une certaine mesure et sont utiles - elles sont cependant pour ainsi dire toutes affectées par des limitations ou défauts plus ou moins sévères. La question demeure quant à savoir si des améliorations supplémentaires peuvent être apportées dans le domaine de la conception pratique des opérations d?abattage du roc à l?explosif. Une approche alternative qui semble prometteuse est celle relativement récente des systèmes matriciels d?ingénierie du roc (?Rock Engineering Systems?, ou RES). Il a été démontré de manière conceptuelle que les RES ont le potentiel d?être adaptés aux opérations de sautage. Une brêve revue des principales techniques de conception des tirs à l?explosif est suivie d?un énoncé des principes de base gouvernant les RES, ainsi que d?une discussion sur leur pertinence aux opérations de tir. Cet article conclut avec la revue d?un projet de recherche axé vers le développement d?une méthodologie de conception des tirs à l?explosif basée sur les RES.

May 1, 2002

By E. Gybbon Spilsbury

The introduction of underground machinery in mines, and especially the invention of the rock drill, called attention to the necessity for some motive power to drive them. The use of steam generators underground is as a general thing inadmissible, owing to the difficulties of ventilation and the transportation of fuel, and the great loss of power by condensation in the pipes, when surface generators are used, added to the inconvenience of getting rid of the exhaust steam, has precluded the direct use of steam for this class of machinery. Water as a power has with very few exceptions proved a failure, owing to its weight and incompressibility, and therefore the attention of mining engineers has very naturally turned to the use of compressed air. This agent not only answers all the requirements for power, but has the double advantage of greatly assisting in thoroughly ventilating remote workings, and in cooling the underground atmosphere. It is therefore clear that the successful introduction of underground machinery is dependent on the economical production of good and efficient air-compressing machinery. Although many improvements have of late years been introduced in this class of machines, the most of them are open to serious objections, the chief of which are the very small duty they perform for the power expended, and their great expense, due to the complexity of their construction. This latter fault is the chief reason why the introduction of rock drills and other underground engines is so limited, as comparatively few mines can afford to expend the required capital for the installation of a complete compressing plant. But with the introduction of a cheap and effective compressor, there is no doubt that power drills will become as generally used in mines as the hand drills are now. The great excess of power required in most machines to compress air over that given out again by the use of the air thus compressed (amounting as it does in most cases to sixty per cent.) is well known to all mining engineers. Of course a portion of this loss is due to the friction of the air through the pipes, and will always occur however effective the machine used may be, but the chief cause of the

Jan 1, 1880

ON JUNE 7 the German Government handed to the French and Belgians a new proposal for reparations, which offered 1,200,000,000 gold marks annually, to be guaranteed as to 500,000,000 by a mortgage on the national railways, as to another 500,000,000 by a mortgage on industry, commerce, land and factories, and as to 200,000,000 by a luxury tax. The number of years for which this payment should run to be left to settlement by an international conference. This offer was taken under consideration by the French and Belgians, who instituted conversa-tions with the British in the hope of arriving, at some joint action with respect to the Germans. Up to the end of June nothing had been determined. In the meanwhile, the continued French and Belgian occupation of the Ruhr seemed to develop a condition of guerilla warfare, considerable bloodshed occurring throughout the region. The second Lausanne Conference dragged on, the Allies being apparently unable to take any firm, joint stand, while the Turks increased their importunities and managed to get concession after concession. Early in June a revolution occurred in Bulgaria, the previous Government under Premier Stambulisky, based on the agrarian party, being forcibly thrown out by a bourgeois and military combination. This pro-duced considerable disorder in Bulgaria, outside of which country the nature and purpose of the revolution does not appear to be well understood. Stambulisky&apos;s partisans offered feeble, isolated resistance to the revolu-tion; in connection with which there was some blood-shed and Stambulisky himself was reported killed, although this was later contradicted. Professor Zan-kof, the new Premier, issued a statement, that the change of the Government was the result of discontent, that the foreign policy of the new Government would be peaceful, and that Bulgaria would continue to fulfill her international obligations, particularly the treaty of Neuilly. It was the opinion of London that the immu-nity from taxation enjoyed by the farmers under the agrarian regime is likely to he superseded by more equi-table taxation, and in general that the bourgeoisie will be better administrators of the public affairs In domestic affairs industrial activity continued at a high rate, but there was distinct relaxation in the demand for raw materials, and also in some manufac-tured goods. During June there were reductions of prices by many of the automobile tire manufacturers. There seemed to be also further contraction in the demand for automobiles.

Jan 6, 1923

By S. Frederick Ravitz, Kenneth E. Fisher

Four liquids are ordinarily present in the lead blast furnace during lead smelting. At the bottom is the lead bullion, which is metallic lead containing about one per cent of impurities, including gold, silver, copper, bismuth, arsenic and antimony. Above this is the speiss, which consists essentially of arsenides and antimonides of iron and copper. The speiss is followed by the matte, which consists principally of sulfides of iron, copper and lead1. The top layer is the slag, of which the major constituents are silica, lime, alumina, zinc oxide and iron oxide. Similar products are obtained from the dross furnace, which treats the dross obtained in decopperizing lead bullion. The distribution of gold and silver among these various products is of considerable importance in the smelting of lead. In general, the matte and speiss cannot be treated in the lead smelter, and usually are sent to a copper smelter. It is usually desirable, therefore, to keep their gold and silver contents as low as possible, and to collect the precious metals in the bullion. If the bullion, speiss, matte and slag exist together in equilibrium, the gold and silver should distribute themselves among these four liquids in a definite manner, which, other conditions being equal, should depend only on the amounts of gold and silver in the charge to the furnace. It is thus apparent that a knowledge of whether such equilibrium exists is necessary before attempting to study the effects of various compositions of matte and speiss on the distribution of gold and silver among the furnace products2. Moreover, systems consisting of four liquids in equilibrium are very rare, and are of considerable scientific interest. In order to ascertain whether equilibrium existed, the distribution of gold and silver among the four liquids was determined. The speiss,

Jan 1, 1937

By David Donoghue

The efforts towards curtailment in Texas have been successful, despite the great area covered and the wide variety of oils offered. There are, of course, examples of noncooperation, perhaps of absolute indifference, but of such it can at least be said that they have benefited from the restrictions imposed elsewhere. The prevention of waste is the legal background for proration in Texas. The legislature in 1899 passed the first laws to prevent waste of oil and gas. Subsequent legislatures, especially those of 1905, 1913 and 1917, undertook to regulate the development and transportation of oil and gas to the end that waste would not occur. In 1917 a constitutional amendment was submitted to the people, providing that natural resources of the state should be conserved and requiring that the legislature pass appropriate laws. This amendment was adopted, and the Acts of 1919 and 1929 have been passed, and these have had the effect of making a rather elaborate plan for the conservation of oil and gas and their protection against waste. In 1930 the new pipe line act, designed to provide for ratable purchases, was passed. The administration of these laws has been placed under the Oil and Gas Division of the Railroad Commission of Texas. The Commission can only consider actual waste, not economic waste. The various proration plans in use in the state, while differing in efficiency, are based on engineering principles. In the proration of flush fields, the limiting of drilling and the steady production of oil under restriction are the principal points involved, and these methods are entirely different from those which prevailed until recently in the Oklahoma City Pool, where apparently nothing beyond the restriction of production on a time basis was attempted. There is little to say in defense of proration in the older and smaller producing areas in Texas, except that, inasmuch as the market outlet has been reduced, proration distributes the market ratably among the producers. Work of Central ProRation Committee In the early part of 1930 the overproduction situation became acute, and, at the request of the Railroad Commission, a committee was formed composed of representatives of the Texas Division of the Mid-Continent

Jan 1, 1931