Search Documents

By John W. Tieman

Coal is a term applied to vegetable matter (trees, grasses, etc.) which was subjected to heat and pressure through geologic ages. This resulted in a change in both the physical and chemical properties. Because its chemical composition is variable, geologists classify coal as a heterogeneous mineral rather than a homogeneous mineral. Peat represents the initial, unconsolidated stage in the development of coal. This coalification continues with time and the application of temperature and pressure to lignite, subbituminous, bituminous, and anthracite toward the theoretical graphite end member. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness and grindability of coal determine the maintenance cost for coal mining, handling, and pulverizing equipment; the specific gravity of coal and its associated minerals determines the coal preparation technique used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent on the chemical constituents of coal, and all properties are interrelated. Specific Gravity The specific gravity (sp gr) of a solid is the ratio of the weight of a cubic foot of the solid to the weight of a cubic foot of water. The specific gravity of pure coal has been reported to range between 1.23 to 1.72 and increases with the change in rank from lignite to anthracite. This means that it is 1.23 to 1.72 times heavier than water.

Jan 1, 1981

By Samuel S. Wyer

The following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests— which has some resemblance to the code of boiler-trials of the American Society of MechanicalEngineers—has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same thing, to see if the efficiency is as high as it should be with the type of producer in question; and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the'producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins,' the efficiency was raised from 56.2

Jan 1, 1906

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By J. Wes Blakely

In the mid-1950s the importation of foreign oil began to encroach on traditional coal markets such as railroad steam engine fuel, home heating, electrical generating plants, and others. Many of the smaller coal companies with substantial coal reserves subsequently found that they could no longer continue to mine economically and merged in various ways with larger established coal mining concerns. As the seats of top management and authority were removed from the mines to large metro centers such as New York, Pittsburgh, and Chicago, the more personal relationship between mine workers and management that had existed prior to these mergers began to be eroded and replaced by "remote control" mine management. The disappearance of this face-to-face contact of upper management with mine employees tended to create barriers blocking simple effective communications between coal mine management and labor. In examining the human relations aspects of the coal mining industry, many elements, some concerned with work and others not, have depicted the industry as almost devoid of good applied human relations and communications practices, and, in truth, little has been done to alleviate this situation. In past years many coal producing companies, with the exception of one of the largest, failed to adequately define the term "communications ' as it applied to their companies, whether internally or externally. Internally many still place heavy reliance on written communications such as company-wide newspapers to do the job of communicating with their employees which they feel ought to be done. One company puts an inordinate belief in its company "newspaper" as the primary instrument to stimulate its work force into increasing productivity. Primarily aimed at the workers, who greatly outnumber the salaried administrative people, this publication mainly documents the fortunes of individual mine workers who are felt to have achieved something with their lives, e.g., a mine worker who had managed to put four children through universities, the

Jan 1, 1981

By George Breyer

DURING the past 25 years the steelmaker has experienced some difficulty in producing steel to meet the standards established by the metallurgist. In contrast to the past, when a chemical specification of broad limits was the only requirement, he now has to employ such tests as microscopic, macroscopic, tensile, impact, Magnaflux and even X-ray and supersonic. The development of these tests has more than set the pace for a manufacturing process of which the exactness still hinges to an important degree on the ability of the furnace operator. In our efforts to produce steel, and especially alloy steel, to meet the exactness of modern engineering specification, many factors must be taken into account. It is not sufficient to make a good heat of steel in the furnace and then be satisfied that the job is done, since there are many pitfalls between the furnace and the finished product. The literature abounds with information on melting practices, deoxidation methods and slag control, but the lack of positive information about what happens when the steel is teemed into molds is quite evident. Such questions as what is the proper mold size, shape and thickness; which is the best mold coating; what is the best rate of pour for any given steel, and what is the effect of cooling rates on quality, are still answered by opinions. It is acknowledged that a poor heat of steel cannot be improved in the pouring pit. On the other hand, a good heat can be ruined by improper handling after it leaves the furnace.

Jan 1, 1947

By Charles H. Behre

This paper discusses education and training for economic geologists other than petroleum geologists. Candidates enter economic geology through liberal arts colleges, engineering schools and university graduate study. Whatever their backgrounds, rigorous courses are desirable-now conceded in theory, but not adequately recognized in practice. Besides basic sciences (each studied long enough to give a fair comprehension of its basic tenets), a functional command of English and two modern foreign languages is needed, as well as a broad understanding of mining, milling and metallurgy. A year of economics and finance is recommended. Surveying and drafting are essential skills. Yet geology should be represented in each term; otherwise the initial enthusiasm for the science, once contact is broken, may never be regained. A five-year curriculum is thus designed to take care of all major requirements and culminate in the M. S. degree. This curriculum reduces "cultural" courses below the average liberal arts requirements, but this is regarded as necessary. The pursuit of "culture" is assigned, as in most engineering and medical curricula, to extra college years or extracurricular time. To avoid the danger of over-crowding the schooling, the Doctorate in geology is preferred wherever possible. Its two added years should permit wider professional education; more browsing in "cultural" pastures; due attention to broader social implications; and some training in the research now increasingly required of the mineral industry. "In-course" training through cooperation between school and industry is especially advocated. The Institute should take the initiative in stimulating this practice.

Jan 1, 1947

Bill S.1431 for the creation of a Department of Natural Resources has received a propitious hearing before the Senate Committee on Government Operations. Interior Secretary Rogers C. B. Morton was one of the prominent witnesses who testified in favor. The department had been proposed, Morton said, with "the conviction that the development of all natural resources would be harmonized with the most practicable possible means to protect and preserve the environment, consistent with the social and economic needs of the Nation." Another opinion on the pro side came from Atomic Energy Commissioner Clarence E. Larson, who said that a "total picture" had become essential to the establishment of a policy for developing energy resources in the best public interest. Commissioner James T. Ramey, on the other hand, was one of the AEC dissenters. Ramey said he believed the reorganization of resource responsibilities would hinder efforts to deal with energy-environmental problems and prevent the use of AEC "expertise and facilities" to the greatest advantage. As Arnold Weber, associated director of the Office of Management and Budget, pointed out, however, retiring AEC Chairman Glenn T. Seaborg is in favor of the new department. Another supporter, and one who can cast a vote on the bill, is Sen. Frank E. Moss. Final Standards for emissions from new stationary sources will be published by the Environmental Protection Agency on October 27. The initial proposals, appearing in the Federal Register on August 17, called for limiting emissions per million Btu of heat input (maximum 2-hr average) to 0.2 lb of particulate matter, and, where solid fuel is burned, to 1.2 lb of sulfur dioxide and 0.7 lb of nitrogen dioxide. While the new rules are mainly for new plants, the EPA is also proposing them for "existing plants which are modified in such a way as to increase or alter. . . their emissions."

Jan 1, 1971

In an earlier paper(l) details of a laboratory method of extracting and separating tantalum and columbium oxides from tantalite have been given. In view of the fact that Australia may have need to be self sufficient in this field it was decided to erect a pilot plant for the production of tantalum oxide in the Metallurgy School, University of Melbourne. The plant was designed for treating about 40 lb. of ore in a batch over a period of two weeks, although; because of the sectionalized nature of the process, the capacity of the plant was 40 lb. ore per week.Australia is fortunate in possessing some very rich tantalite and columbite deposits, particularly in the Pilbara District in Western Australia. The ore used in this work was obtained from a small but high grade deposit near Greenbushes, Western Australia, and consisted of lumps, weighing up to 8 lb. each, of almost pure ferro-tantalite with occasional thin veins of the very' rare' mineral stibiotantalite.The main constituents were:

Jan 1, 1946

By Yasuo Omori

Stabilized blast furnace operation at high production rates and reduced coke consumption requires control of the gaseous distribution within the furnace. This can be achieved only by an increased use of agglomerates in the furnace burden, and control of the radial distribution of agglomerates and that of coke in the blast furnace. Dissection surveys of commercial blast furnaces recently conducted by several steel plants in Japan gave much valuable knowledge on the behavior of agglomerates within the blast furnace, specifically in regard to the softening-melting zone. The authors analyzed these survey results in conjunction with laboratory studies on the behavior of agglomerates, then proposed appropriate test methods to determine high temperature behavior. A reducibility test at temperatures over 1100°C, a test for softening and melting under load up to 1400°C, and a test for melt-down characteristics were developed to evaluate behavior of agglomerates in the softening-melting zone of the blast furnace. The high quality of self-fluxing sinter, as compared with pellets, was verified by means of these test methods. The test conditions of the respective test methods were examined in detail.

Jan 1, 1977

By Arthur S. Dwight

The profeseional career of Thomas Septimus Austin, who died at El Paso, Tex., Aug. 23, 1906, was contemporaneous with the growth of the silver-lead smelting-industry of the Far West, to which his talents and zeal contributed in no small degree. Born at Stratford, Conn., Dec. 7, 1853, he was the seventh son in a family of thirteen. His parents were well-to-do; and he received a thorough preliminary training at the Hopkins Grammar School, New Haven, Colin., passing thence to the Columbia School of Mines, in New York, where he was graduated in 1876. His first professional work was that of analytical chemist with a Cuban sugar company. In this position he spent a year, and, whatever else of benefit he may have acquired during that year in Cuba, he gained a facility of speech in the Spanish language which was of inestimable value in his subsequent work in Mexico and the southwestern United States. In 1877, he went to the Rocky Mountains, and, under the firm name of Murphy & Austin, opened an assay-ofice in Lead-ville, Colo., which was just then coming into public notice as a rich silver-lead camp. The next year, however, he entered the service of the Germania Smelting & Refining Co. at Salt Lake City, Utah, where he remained until 1882, first as assayer and chemist, and later as Assistant Superintendent. The Germa-nia bears the honorable distinction of being one of the first of the large " custom" lead-smelters erected in the West. Its founders may be called the pioneers of the modern lead-smeltr ing practice, and the Germania served, to a large extent, as a model for the many plants that sprang into existence during the next few years in Utah, southern Idaho, Colorado and other lead-producing districts. The formulation, for the first

Jan 1, 1908

This paper is intended to continue the subject in the light of recent work, from where it was left at the conclusion of the discussion on the excellent paper by the late Mr. Noel Haszard. The position then obtaining is briefly summarised below:-The points which received general agreement at that time were:-'(1) That the gold occurs, probably in an elemental form, in a state of very fine division in the pyrite.(2) That the aim in roasting of Kalgoorlie flotation concentrates should be to obtain the maximum porosity possible. The gold tellurides were amenable to treatment with either a' solution of high lime and cyanide strength combined with fine grinding, or bybromocyanidation without re-grinding.(3) That a low roasting temperature is essential during the elimination of the first atom of sulphur, if the final calcine is to give a good extraction by cyanidation.(4) Even with the best temperature conditions of roasting then determined, and after a period of cyanidation of the calcines until no further extraction was obtainable, the lowest calcine residues obtainable were equivalent to approximately 1·8 dwts. per long ton, based on an original concentrate of pure pyrite.There was some division of opinion at the time as to whether the temperature of the later stages of roasting was significant, and also as to the reason why the initial roasting temperatures had so marked an effect.

Jan 1, 1939

By Gordon King

This paper presents a case study of large diameter continuous flight auger (CFA) piles and drilled shafts utilized for foundation support of a series of heavily loaded cement plant structures at the Suwannee American Cement (SAC) Plant in Branford, Florida. The high loads and exacting total and differential settlement criteria when combined with a highly variable subsurface geology provided a challenging design scenario. Fully instrumented static pile load tests were performed to determine design parameters in the variable weathered limestone bedrock. Ultimate side friction values ranged from 2 to 8 tsf within the limestone, resulting in the requirement for CFA piles up to one meter (approximately 40 inches) in diameter and socket lengths of up to 40 feet. At several localized areas, the limestone bedrock was in excess of 60 feet below grade, requiring the use of cased drilled shafts to depths on the order of 80 to 90 feet. An integral part of the production pile installation was the use of instrumentation to monitor drilling and concreting parameters. Calibration of drill rates, torque and auger rotation with rock quality was performed to allow monitoring of the soil stratigraphy at each pile location. When combined with the results of the instrumented load testing, the monitoring of drilling parameters allowed confirmation that sufficient socket length was achieved within the quality of rock present at each and every pile location.

Jan 1, 2003

By L. H. Munson, E. H. Carbaugh, D. E. Hadlock, L. F. Munson, R. L. Gilchrist

As a result of the Three Mile Accident and because of evidence indicating radiation protection problems, the U.S Nuclear Regulatory Commission (USNRC) undertook a major effort, with the assistance of the Pacific Northwest Laboratory (PNL), to analyze radiation protection programs at 47 commercially operated nuclear power plants. This effort, the health physics appraisal program (HPAP), using a modified management oversite and risk tree analytical logic methodology (MORT) which consisted of analytical trees with applicable questions for each tree, was subsequently extended to include USNRC licensed uranium mills. In the uranium mill appraisal, a team of four senior radiation safety professionals spent a week at each mill evaluating the total health physics program. Prior to the HPAP, the USNRC inspection efforts were designed to determine if the licensees were fulfilling the requirements of the code of federal regulations and the mills source material license. The HPAP, however, was designed and structured to facilitate an integrated look at the total program. It is also directed into areas for which explicit NRC regulatory requirements may not currently exist. The latitude of the HPAP was designed to allow professional judgement in the evaluation of program adequacy, because merely meeting the explicit regulatory requirements does not necessarily ensure an adequate and effective health physics program. The results of the first eight site visits and the generic health physics problems identified within the uranium milling industry will be identified in this paper.

Jan 1, 1981

British Coal has always been a big mining company and its management has been beset with many of the problems one would associate with such an undertaking. These include its accountability to Government, its market vulnerability to competing fuels and to imported coal and its relationship with its workforce but also with its own history and size. As a fragmented private industry up to and including the Second World War, it was starved of capital and its management developed an historic relationship with its workforce which was often counter productive to success. Once nationalised, it contributed greatly to post-war industrial regeneration, investment was forthcoming to reconstruct existing mines, sink new ones and to mechanise production operations. British manufacturing companies contributed to this mechanisation drive, the very success of which drove up production and productivity and against a declining market, contributed to the reduction in size of the industry. Production machinery design evolved in the 1960s with close collaboration between manufacturers and users such that an inevitable proliferation of machinery types and specifications developed to meet local needs. Longwall mining internationally outside Western Europe only became significant in the 1970s. It became apparent that international operators demanded higher levels of plant performance from British manufacturers than British Coal did. This was the birth of the "heavy duty" plant concept. As international performances outstripped our own then British Coal moved in to invest in itself, in this heavy duty. This re-investment commenced in the mid 1970s but only gained real momentum in the 1980s when it became a virtual re-equipping exercise for the whole industry.

Jan 1, 1988

By Donald V. Fites

In the face of an increasing demand for minerals, the resulting technological developments, and rising overburden-to-ore ratios, many open-pit mines now incorporate totally different concepts for the removal of ore and overburden. Moreover, under a growing number of these concepts, wheel tractor scrapers are being assigned a major role in material- handling systems for unconsolidated overburden removal. To say that scrapers move only unconsolidated overburden is incorrect. On the contrary, ripped phosphate rock, copper ore, iron ore, and moderately consolidated overburden are also being moved by scrapers in various areas of the world. According to the Minerals Yearbook, about one half of the material moved in metal and nonmetal mines is never drilled, blasted or broken by other means. Scrapers Find Wider Application The increased use of scrapers in open-pit mining today is due in part to improved design which has endowed these units with added versatility and in- creased their production capability. The modern scraper, which is designed as a loading and hauling vehicle, cannot be compared to the original tractor- drawn scrapers which were limited in capacity, maneuverability, and speed. Improved design of the scraper bowl ejection system has aided production. Gravity ejection has been replaced with positive, forced ejection of material by hydraulic or mechanical action. Bowl and cutting-edge design which allows for maximum load with minimum effort has also increased production. An example of this was the introduction some years ago of the low-silhouette scraper bowl which reduced the work required to lift the material.

Jan 5, 1969

By G W. Wilson, C Panidis

Potentially acid forming (PAF) waste rock contained in dumps formed as a result of open cut mining of metalliferous orebodies are conventionally sealed or covered using a near-saturated, low permeability compacted clay layer, protected with a mulch layer and/or vegetated growth medium. The purpose of the compacted clay layer is to limit oxygen diffusion and the infiltration of rainfall into the dump. Where the aerial extent of the PAF waste rock dump is large, or where suitable clayey material is in short supply, it may be difficult to source sufficient suitable clayey material to form the cover. The paper describes a laboratory-based investigation of combining inert waste rock and tailings to form an alternative seal or cover material. The inert waste rock was sourced from the trafficked surface of a non-acid forming (NAF) waste rock dump, with a maximum particle size of about 100 mm. This was combined with NAF thickener underflow tailings slurry in various mass ratios, and the resulting mixtures tested for their particle size distribution, compaction characteristics, soil water characteristics (relationship between suction and volumetric moisture content), and saturated hydraulic conductivity. The mixtures tested ranged in consistency from those dry enough to be compactable, to those with the consistency of wet concrete that lend themselves to placement without the need for compaction. The laboratory test results showed that the suitability of the mixtures as seal or cover materials is very dependent on the particle size distribution of the mixture, with well-graded mixtures having substantial fines performing best.

Jan 1, 2003

By Julius Pohlman

Considering the truly wonderful natural resources of the United States, and the variety and extent of uses for hydraulic cement at the present day, it seems strange that the manufacture of the artificial product called Portland cement has not been introduced here. Possibly the reason may be we have in different States of the Union rock deposits from which a cement can be obtained that is as good, and some claim even better, because of a more uniform quality, than the English product after it has been subjected to transportation across the ocean. One of these natural cement-rock deposits is found in the northern part of the city of Buffalo, and its manufacture has been carried on successfully for the past eleven years by the Buffalo Cement co., Mr. L. J. Bennett, President. The quarries cover an area of about two hundred acres, of which only twenty-five acres have been exhausted up to date; and the supply is assured for years to come. One acre yields on an average 80,000 barrels of cement; hence 12,000,000 barrels is a low estimate of what these quarries will yield before they are exhausted. According to the Geology of New York this cement-rock deposit is called the Water-Lime group, and forms in this section the uppermost member of the Upper Silurian. Its outcrop can be traced along the base of the second limestone terrace of Western New York, but at Buffalo a very large part of the overlying Corniferous limestone has been removed by natural agencies, leaving only about eight feet (six feet of rock and two feet of clay) on the top of the cement-rock, and thus furnishing the conditions for successful quarrying at a minimum expense. This rock is really an impure limestone, a mixture, as it were, of the underlying shales of the Onondaga Salt group with the overlying

Jan 1, 1889

By P. Chris Pistorius

Calcium treatment of alumina inclusions, to convert the alumina to molten or partially molten calcium aluminates, is a well-established treatment for steel, to improve the castability of aluminium-killed steel. However, the role of magnesium in calcium-treated steel is not fully clear, nor is the origin of the several percent of magnesium oxide that is often present in calcium-treated inclusions. To study this, steel was sampled after calcium treatment at an industrial steel plant, and the inclusions identified by energy-dispersive X-ray microanalysis (EDX) on polished sections of the samples (analysing the samples in a scanning electron microscope). The predicted fraction liquid in the inclusion was estimated from the ternary alumina-magnesia-lime phase diagram. Inclusions with higher CaO contents generally had lower MgO contents, indicating that the calcium wire is not the origin of the magnesium in the inclusions; this was also confirmed by wet chemical analysis of the calcium wire. Instead, it appears that magnesium-alumina spinel inclusions form during extended ladle contact after aluminium killing and before calcium treatment. While such spinels have been stated to cause poor castability (clogging the submerged-entry nozzle), it is clear that calcium treatment successfully modifies the spinel inclusions to mixed alumina-lime-magnesia inclusions, where the magnesia content contributes substantially to liquefaction of the inclusions: for typical MgO contents of around 10%, the range of Ca:O ratios which yield liquid (or partially liquid) inclusions is extended substantially to lower Ca:O ratios.

Jan 1, 2006

By C Gunther

The term metamorphism as commonly used means any change in a rock in either form or composition, from whatever cause. By metasomatism, according to Lindgren, is meant a metamorphism that involves a change in the chemical composition of a rock by the addition or subtraction of substance. Certain types of metamorphism are due to the action of mineralizing solutions, and are closely connected with ore deposition; they form, therefore, valuable guides in the exploration for ore-deposits. Other types of metamorphism are due to regional processes, and are not connected with ore deposition. By dynamo-regional metamorphism is meant a primary alteration of rocks over large areas under conditions of pressure, flow- age, and heat. This process produces schists and gneisses from either sediments or igneous rocks. It is thought that there is little migration of minerals or of elements in dynamo-regional metamorphism, and that the changes are due chiefly to recrysallization and rearrangement of original minerals in bands with their major axes oriented normal to the direction of greatest pressure. Under these conditions limestones are commonly altered to marble, and sandstones to quartzite, basic igneous rocks to greenstone or serpentine, while rocks of normal or acid com- position commonly yield the usual types of schist or gneiss. Dynamo-regional metamorphism, extending over large areas, has no connection with mineralizing processes, and is, therefore, no guide to ore deposits; while this process has certain features, such as characteristic mineral associations, in common with contact metamorphism, the results of the two processes may usually be distinguished without difficulty.

Jan 1, 1932

By Hyun Sub Kim

Subsea mineral deposit exploration aboard the R/V Onnuri was performed along the northern Central Indian Ridge (CIR) between 8°S and 17°S in December 2009 ~ January 2010 (09IR Leg01 and 09IR Leg02) and December 2010~ January 2011 (10IR Leg01, 10IR Leg02, and 10IR Leg03). Final goal of the expedition for the first Korean research cruise on mid ocean ridge system is to define seafloor massive sulfide ore bodies through searching the active hydrothermal vents nearby spreading centers as well as to elucidate the nature of spreading segments of the northern CIR area where no systematic survey have been operated before by mapping and sampling of volcanic rocks. The preliminary result of topographical interpretations of bathymetry clearly display ocean core complex between 10°S and 11°S. The ocean core complex is featured by topographic-high area with corrugated surface. Lineaments of corrugations of the ocean core complex are clearly perpendicular to abyssal hill direction which is triggered by symmetric-normal faults. Ocean core complex are favor for hydrothermal fluid path because of the long-lived faults. In further exploration, more detailed examination, including systematic CTD casting and tows, need to narrow down actual venting site around ocean core complex. Magnetic field survey is able to estimate the location of hydrothermal vents with the properties that high temperature of hydrothermal fluids over Curie-point can cause thermal demagnetization. In magnetization intensity map, most of low magnetization zones are located at the nodal point over the ridge axis and the ocean core complex.

Jan 1, 2011