Search Documents

By Gerald L. Stolarczyk

Safe and efficient coal extraction requires advanced radar subsystems that can be mounted on cutting drums of coal cutting machines. A look-ahead radar (LAR) must solve the radio geophysics problem of transmitting an electromagnetic (EM) wave through at least 20 feet (6.1 meters) of coal to an air- or water-filled void. The reflected EM wave must be processed in the radar electronics to determine the physical distance to the void. Horizon sensing enables selective cutting near the undulating sedimentary rock boundaries of the coal bed to address coal quality and ground control issues. Both sensors require subsystems for dynamic electric power generation, real-time measurement of drum rotation angle, detection of reflected EM waves, and processing to determine distance through coal and RF modem transmission of measured data to the mining machine. This paper describes the development of the subsystems and field test results.

Jan 1, 2006

By J. A. Hayes

For over a decade the Osterberg Load Cell has been successfully used to determine the shear capacities of drilled shafts. Since the test method measures side shear directly, analytical complications due to the influence of end bearing resistance are removed. The data suggest that the side shear component of a drilled shaft's capacity is often more significant than end bearing. Given the interest in the use of side shear in drilled shaft design in compressible materials, it is important to examine factors that can influence capacity. We have found that some factors widely believed to influence capacity, such as slurry type, are not as important as commonly thought in most materials. Factors that are not usually considered as important, such as casing use, hoop spacing, concrete slump, concrete additives, spacers and rebar clear cover, seem to be more influential with respect to side shear capacity. For example, substantially lower than predicted shear resistance can occur when the rebar clear cover is small with respect to the cage diameter. We observe this most often in fine-grained cohesive soils. This effect can be exaggerated if the rebar cage has tight hoop spacing, if the concrete has low slump and if the hole is not straight. We have also noted that improper use of temporary casing can have a dramatic effect on side shear resistance. In some cases we have observed tested shear capacities reduced to less than 5% of either predicted or available shear values.

Jan 1, 2003

By James V. Errico

On October 1, 1993 the regulations for assessing and cleaning up contaminated soil and groundwater in the Commonwealth of Massachusetts were revised. These new regulations, known as the Massachusetts Contingency Plan (MCP) 310 CMR 40.0000, were developed to keep routine releases out of the regulatory system and rely on private parties to handle most releases without Department of Environmental Protection (DEP) oversight. An integral part of the new MCP is the Licensed Site Professional (LSP). An LSP is required to handle activities and render opinions once a site enters the MCP. These regulations must be adhered to where ever a release has occurred, including construction sites. A brief overview of the new MCP is given below; see attached MCP Flowchart for graphical summary. Entering the MCP Process A release of oil or hazardous material (OHM) to the soil or groundwater above applicable reportable quantities (RQ's) or reportable concentrations (RC's) will require notification to the DEP and compliance with applicable provisions of the MCP. RQ's and RC's are listed in the MCP (310 CMR 40.1600) for most compounds that are typically encountered. For each compound there are two RC's for soil (S-1 and S-2) and two for groundwater (GW-1 and GW-2). The S-1 and GW-1 RC's apply to sites that are environmentally more sensitive, as a result they are lower than the S-2 and GW-2 RC's.

Jan 1, 1994

By Ian Bruce

Tailings and water management facilities are essential and integral components of mine and mill operations. They must be managed for the long term in order to ensure that safe and environmentally responsible stewardship is achieved. Toward this end, in 1998, The Mining Association of Canada (MAC) published A Guide to the Management of Tailings Facilities, which recommended the implementation of a tailings management framework (Figure 1) to integrate environmental and safety considerations into each stage of the life cycle of a tailings facility, from initial site selection and design, through construction and operation, to eventual decommissioning and closure. By February 2000 it was becoming apparent that while mining companies were making significant progress toward implementing and documenting tailings management systems, and integrating them with overall environmental management systems, further effort was warranted in their application at the operational level. In particular, a need was identified for further guidance in preparing manuals that outline procedures for the safe operation, maintenance and surveillance (OMS) of tailings and water management facilities.

May 1, 2002

OVERVIEW OF PRESENTATION ? What is LMI ? Who uses LMI and how? ? Value of LMI to the Mining Industry ? Mining Industry Workforce Information Network (MIWIN) ? The Challenge: Forecasting the future in uncertain times ? Results: Hiring requirements in the next decade ? Results: Occupational information ? Next steps

May 1, 2009

By W. J. Nokleberg, B. A. Bouley, T. K. Bundtzen

Central Alaska contains a wide variety of pre-, syn-, and post -accretionary mineral deposits that are related to the growth and evolution of the north-west North American continental margin. Withinpre-accretionary terranes, the Devonian-Carboniferous, carbonate platform-hosted MVT zinc-lead deposits of the Kandik and Reef Ridge districts in central Alaska, and the Devonian-Mississippian volcanogenic massive sulfide (VMS) polymetallic deposits of the Bonnifield, and Delta mineral belts of eastern Interior Alaska have received the most exploration interest to date. Syn-accretionary rift related, mafic and ultramafic sill swarms and zoned plutons of the Kluane-Nikolai igneous belt are currently being explored for Ni-Cu-Co-PGE deposits. Syn-accretionary granitoid complexes in the PurcellMountains, Illinois Creek, and Sitylemenkat areas have been explored for uranium-REE-gold, and tin-silver mineralization respectivelyPost-accretionary granitoid intrusions and associated volcanic fields that range in age from mid-Cretaceous to early Tertiary contain significant gold-silver-polymetallic resources in the East Central Alaska, Hogatza, and Kuskokwim Mineral belts. Collectively the three main post-accretionary plutonic/volcanic belts of central Alaska are part of the Tintina Gold Province, where exploration since 1990has identified about 848 tonnes gold.

Jan 1, 2000

Taking the third meridian as the eastern boundary of proved payable auriferous country, there is a stretch of country, nearly 600 miles in width, in which no appreciable amount of gold has yet been discovered. Many prospectors have attempted to .penetrate or traverse it, but comparatively few have thought it worth while proceeding with the examination.The desolate stretch of waterless desert-the very few and insignificant outcrops through the sand and the almost total absence of feed for horses have, combined, presented such a barrier as to preclude prospecting. The few who have traversed the country are eloquent in denunciation, yet their investigations, necessarily hurried, are not quite satisfactory. The absence of water utterly debars a thorough examination being made. Gold may exist in quantity, yet it would have to be extraordinarily plentiful to render its obtaining profitable. Too fantastic is the idea of its ever being a mining district; shifting sand to traverse, utter absence of wood and water render the notion absurd. Likely looking belts occur, but these in all "cases are small and remote from water. Gold has been obtained from likely look ing quartz reefs, but only by fire assay, and then but a few do to the ton. Without wishing to be pessimistic, I would unhesitatingly declare that east of the third meridian, and between the parallels 25 and 30 degrees in West Australia, there is no gold in payable quantities.

Jan 1, 1901

By Maurice Hunter

The paper outlines recent design developments in the computerization of surface crawler drills for the quarry industry. It references the technology firstly developed for the underground mining and construction industry, where automation and computerization has been in demand for a number of years.

Jan 1, 2003

By C. Righi, R. Carli

In modern steel continuous casting technologies mould fluxes are well-known to assure lubrication required by tribological system of mould-solidifying strand shell, and to provide crystalline phase solid film, contributing to control heat extraction between strand and mould wall. Actual cooling rates during normal continuous casting mould operations are far higher than critical cooling rate of the liquid slag. Indeed, DTA measurements point out that even relatively small cooling rates of 30?50 K/min are high enough to give exiguous formation of crystals. In this paper, contribution of devitrification in defining crystalline phase formation of industrial basic mould slag, used in continuous casting of crack-sensitive steel grades, has been investigated by means of non-isothermal experiments study. Devitrification has proved to play a major role in mould flux crystallization in a working environment explaining the higher amount of crystalline phase formed in plant sample in comparison with lab sample from DTA analysis with typical cooling rate of 5?20 K/min. The amount of crystalline phases formed ranks as follow: Cuspidine > Combeite > Gehlenite. Kinetic analysis of DTA non-isothermal experiments has provided kinetic parameters through Kissinger and Ozawa methods, as Avrami constant resulting to be n ?2 and activation energy of Cuspidine crystallization resulting to be EC= 315 kJ/mole. The effect of addition to the parent material of oxides as MnO, TiO2, ZrO2, Al2O3 and Fe2O3near to saturation point has proved to affect, in certain cases, crystallization behaviour of mold flux. In particular, MnO, TiO2, ZrO2oxides produce a relevant dump of crystallization of Combeite and Gehlenite phases, while Al2O3and Fe2O3do not appreciably affect crystallization. Key words: Mould flux, crystallization, devetrification, DTA non-isothermal analysis, Kissinger and Ozawa methods.

Jan 1, 2004

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

Enhancement of Energy Efficiency in Fine Grinding of Copper Sulfide Minerals Using a Pilot-Scale Stirred Media Mill - IsaMill The mineral liberation size of run of mine ores has dramatically reduced over recent years. As a result, the demand for fine grinding which is the most energy-intensive form of grinding has markedly increased in the minerals industry. Furthermore, the fine grinding costs increase exponentially with decreasing product particle size. As a result of the increased energy requirement for fine grinding, it is desirable to optimise fine grinding processes such as stirred media milling (ie IsaMill) to enhance energy efficiency, throughput and the product fineness. In the present study, the influence of slurry rheology, grinding media type and grinding media-to-feed size ratio on energy efficiency in a pilot-scale IsaMill was investigated under certain industrially relevant pulp processing conditions. It was shown that a critical rheological state existed, below which the energy required to achieve an 80 per cent passing (ie P80) 20 ¦m product size was unaffected by shear rheology (ie apparent viscosity and shear yield stress) whilst above which the grinding energy required increased dramatically with increasing shear rheology. Colorado River sand (3.35 mm) showed higher energy efficiency than MT1 ceramic media (2.5 mm) for a target P80 of 20 ¦m in the solids concentration range of 38 to 55 per cent by weight, but the former experienced more than four times the wear rate of the later. The high wear rate of the Colorado River sand may be due to its much lower hardness. For feeds with an 80 per cent passing (ie F80) 70 to 110 ¦m, 2.0 or 2.5 mm MT1 media appeared to be more energy efficient than 3.5 mm MT1 media whilst a media-to-feed size ratio of 41 to 53 is applicable for ~50 ¦m (ie F80) feeds for efficient grinding.

Sep 13, 2010

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases.

Jan 3, 1955

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008

By L. Douglas Smoot

This research program was a theoretical and experimental study to improve understanding of the mechanisms of flame extinguishment in methane-coal dust-air-suppressant mixtures. This final report is a summary of work conducted during this grant, sponsored by the Bureau of Mines. Work under this new grant closely followed a recently completed contract for the Bureau of Mines that was conducted at this laboratory, and results of the earlier contract are also summarized in this report, as required in the grant work statement. The experimental effort was concentrated on supplementing the limited data available to describe laminar flames in methane-coal-air-suppressant mixtures. The theoretical effort was devoted to developing a comprehensive model that could be used to explain and extrapolate the experimental data. Selected for study were the following flames: Methane-air; methane-air plus KHCO , KNO3, K C204, KBr, Al203 or Monnex; methane-coal dust-air; coal dust-air with size, volatiles content, and concentration as variables, and coal dust-air plus KHCO3, KN03, KBr, NaCl or CaC03.

Jan 1, 1978

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012

By Irvin Pritts

This report describes the design, fabrication, and testing of a prototype instrument which demonstrates the feasibility of determining respirable coal dust concentrations by light reflectance photometry. Coal dust is collected on a filter and the quantity collected is continuously monitored by reflectance-photometry. Light emission and detection is accomplished by reflective object sensors, which have both light source and detector in one chip. The use of a pulsed light source insures low drift characteristics of the measuring circuitry. The collection of the respirable coal dust on filters facilitates accurate calibration and also allows measurement verification, if desired, by well-accepted, gravimetric methods.

Jan 1, 1981

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983