Search Documents

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By Octavio G. Echavarria

HISTORY The Santander Mine is located on the western flank of the Central Andes of Peru, about 100 miles northeast of Lima, at an elevation of 15,000 ft. This complex sulphide orebody, whose predominant minerals are sphalerite and marmatite with recoverable amounts of galena and chalcopyrite, was discovered around 1920. In 1956 Compania Minerales Santander, a subsidiary of St. Joe Minerals Corp. acquired the property. Construction of the camps, concentrator and power facilities started in 1957. The mine, at first an open pit operation, and mill began production in January 1959. The initial capacity of the mill was around 120,000 short tons per year (stpy). Production has increased steadily to about 312,000 stpy at present. Production statistics are shown in Table 1. [ ]

Jan 1, 1970

By K. Gum, W. C. Hirt, D. A. Rice

Selective flocculation was used to produce a superclean zinc concentrate by minimizing silica contamination. Research was carried out on a flotation concentrate from the Jersey Miniere Zinc Company (JMZ) in Gordonsville, TN. The material was first dispersed with sodium silicate and then causticized tapioca starch was used to selectively flocculate the sphalerite, leaving the silica in suspension. This technique has been applied commercially to iron ore beneficiation but never to zinc processing. The feed material assayed 0.45% SiO2. The use of 0.56 kg/ t (1.13 lb/st) sodium silicate and 0.070 kg/t (0.141 lb/st) causticized tapioca starch resulted in a 98.2% zinc recovery and produced a purified zinc concentrate assaying 66.0% Zn and 0.24% silica. The target level for silica contamination in JMZ zinc concentrates is currently 0.30% Si02. This work demonstrated that selective flocculation is a potential method for cleaning flotation concentrates, particularly where low silica products are required.

Jan 1, 1995

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents and particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and conditioning time, were investigated to determine their effect on reagent coating of the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power (P) to the minimum power (Pm) required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain a high recovery. Reagentization was slower at lower P/Pm ratios. At higher P/Pm ratios, the flotation recovery was optimized, and the agitation speed was found to have no significant effect. Optimum mixing conditions were obtained for a74 wt% slurry at an agitation speed of 450 rpm (47 radians/sec). Under these optimum mixing conditions, the collector dosage required for an improved recovery was lower and the conditioning time was shorter.

Jan 1, 1997

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By Thomas J. Ferree

The principle mineral concentration practices today can be divided into three basic process categories: magnetic separation, flotation and gravity separation. The basic processes have been in use for many years with only limited changes occurring in equipment design or process technique. In general, equipment and process techniques have been altered only after a need for change has developed. With exceptions for changes necessitated by new environmental laws, most equipment and process improvements have evolved in accordance with the desire to concentrate larger quantities of material at lower costs. The basic result has been the development of larger capacity equipment, to wit: larger flotation cells, larger blast furnaces, larger haulage equipment and larger chemical process equipment. However, there has been practically no changes in the size of spirals, tables, jigs, or-within limits- magnetic separators. (The exception being high-intensity magnetic separators). Consequently, a "new" device has entered the scene which may fill a void in the gravity separation field. It is called a Reichert cone concentrator.

Jan 3, 1973

By R Balusu

This paper provides an overview of computational fluid dynamics (CFD) modelling capability developed by CSIRO with the aim of improving the knowledge of flow migration dynamics within longwall goaf areas. The CFD models can be used to study the ingress of oxygen into the goaf in different ventilation scenarios and goaf drainage arrangements. This approach not only helps the design of effective gas control strategies but also the management of spontaneous combustion risk in the goaf. Innovative goaf inertisation strategies have been developed and implemented during longwall sealing operations. Work is continuing to develop general guidelines of proactive goaf inertisation strategies to suppress the development of spontaneous heating behind active longwall faces.

Jan 1, 2005

By Atsuo Inoue, Toshihiro Ogata, Hideaki Sugihara

Generally in Japan, since ANFO has easy handling and low-price, it is most used as industrial explosives. However, ANFO is very easy to dissolve in water, it is difficult to use under existence of water and the consumer have desired water-resistant ANFO which has perfect water resistance. Then, we have developed the Water-Resistant Granular Explosive (It is written as following WRGE.) in which the surface of the explosive was covered by waterproof film, so that WRGE is able to use in hole with water. We ran various performance tests about the WRGE developed in the laboratory. Consequently, WRGE has water resistance of over 6 hours, and it has been checked that a performance and handleability were equivalent to the conventional ANFO. Then, we carried out the field test in the consumption site, and did performance evaluation on an on-site level. As compared with ANFO, fragmentation (size and volume) and handleability are almost equivalent. However, some problems which the WRGE is not settled out smoothly in hole with water and need more time for loading were also clarified. We are going to continue some advanced improvements through field tests.

Jan 1, 2005

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By James Warren Andrews

The values of saturated water vapor pressure from steam tables have been found to be inaccurate for mine ventilation usage because the effect of air on the saturated water vapor was disregarded. Presented here are the newest and most accurate currently available tables from the National Bureau of Standards (NBS). Also included are: (1) a formula for correcting the saturated water vapor pressure for temperature and altitude. (2) a formula for computing unsaturated water vapor pressure, and (3) a formula for air density. Because Systeme International (SI) units are used in the formulas, conversions are given from U. S. conventional units to SI units. The intent of this paper is to show by means of six steps the accurate calculation of mine air density for use on modern computers.

Jan 1, 1989

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By Graham MacFarlane

The eastern coal-field of Kentucky covers about 11,000 square miles of territory. On the east and south it extends to the State lines of West Virginia, Virginia and Tennessee. Its western boundary may be roughly described as an irregular line beginning at the Ohio river, in Greenup county, thence through the counties of Carter, Menifee, Wolfe, Estill, Jackson, Rockcastle, Pulaski and Wayne, to the Tennessee line. The changes in the rock-intervals and in the coal-seams from the northeastern end of the field to the south and southeastern end are so great that no satisfactory identification of the coals has yet been made, and the correlation of the Kentucky coals

Jan 1, 1896

By B. Stoughton, H. O. Hofman

Before examining a fire-clay in the labori~tory for its resistance to heat or to fluxes, the sample is always ground to an impalpable powder. But when the clay is actually used for the manufacture of bricka, blocks, pots, etc., it is not ground to a uniform size, the particles varying from coarse grains to the finest slimes. The natural inference is that the tests with finely-ground substances mill give lower results than if the materials are tested just as they are going to be used. The, following experiments were made to find out how far this inference is justified. The method employed for fusion was Seger's direct method,* and, for fluxing, the modified Bischof method, described in the paper on that subject presented at the present meeting, The first question to be decided was, how large the test-cones ought to be made, to include representative proportions of the diflerentrsized particles colnposing the mixture. This was subjected to a screenanalysis with the following results :

Jan 1, 1899

Steel Tape The new Lufkin Royal Ni-Clad steel tape, made in 25, 50, 75, and 100-ft sizes, is stated to cost less than any other steel tape on the market. Figures and graduations are an integral part of the steel and the nickel plated surface is rust and corrosion resistant. Circle No. 1 Lift A manually operated and propelled hydraulic lift marketed by Century Products Co. weighs only [ ] 150 lb, but the 23x24 in. platform will raise 1000 lb from floor level to 4 ft height. Circle No. 2 Scintillation Counter The Scintillator from Precision Radiation Instruments, stated to have 100 times the sensitivity of the Geiger counter, is suitable for prospecting and may be operated from plane or moving vehicle. The instrument is contained in a 2-lb probe and the belt mounted battery box weighs less than 4 lb. Circle No. 3 Generators Wincharger Corp. announces development of a Speedy-Shift wheel-barrow base type attachment for model 700, 1800 and 5000 engine-generator sets. Portability of the engine-generator sets themselves has been improved by belted construction for higher operating speed and maximum weight reduction. Circle No. 4

Jan 1, 1952

By M. A. Bronston

A drill system configuration capable of working in the arctic offshore environment was developed to evaluate the placer gold resources contained in the glacio-fluvial sediments offshore Nome, Alaska. This system is capable of working on the shore fast ice during the winter months and is deployed on a drill ship during the summer. Transfer of the drill between its summer and winter configurations is accomplished with a minimum of modification to the design. The system is designed around the Becker drill. This percussive, reverse circulation drill is capable of penetrating the indurated glacial sediments present in the offshore Nome environment. This drill has operated effectively to depths in excess of 50 m (164 ft) below sea level. Since early 1987, in excess of 2000 holes have been drilled using the system. The drill system often operates in extreme weather conditions. It has averaged approximately 10 holes a day of drill production. The ore reserves defined during these drilling programs have resulted in the recovery of more than 70,000 oz (2.18 t) of gold to date, by the mining vessel Bima.

Jan 1, 1990

By G. L. Hundley, R. E. Mussler, D. H. Yee, F. E. Block, R. S. Olsen

An anhydrous chlorination process for the recovery of copper from chalcopyrite was investigated. Pelletized concentrate was reacted continuously with gaseous chlorine in a vertical shaft reactor at 550° and 650°C. While the copper was withdrawn with the rest of the metals as molten chlorides from the bottom, 99-x% sulfur was distilled from the top of the reactor. The molten metal chlorides were pulverized and dropped continuously into an upward flowing stream of oxygen. Over 80% of the iron chlorides were converted to oxides in a vertical free-fall reactor at 800° and 900°C while the copper chlorides passed through unoxidized. Copper was recovered in powder form by electrowinning continuously from chloride solutions using a diaphragm cell. The product sloughed easily from a titanium cathode and showed no iron contamination. Current efficiencies and power consumptions averaged 77% and 1.24 kw-hr per lb.

Jan 1, 1974

By Walter A. English

The four papers making up this symposum have been prepared especially for those who have no knowledge of seismograph prospecting. To many people mathematics is a formidable subject, and many are discouraged from studying seismograph prospecting under the mistaken assumption that the mathematical requirements are severe. In the papers presented here there is not a single mathematical equation. We believe that considerable competence in dealing with some of the most important problems of this work can be attained without any mathematical training whatever. At the present time, there is a real need for interpretation of results by persons thoroughly competent to bring geologic experience and imagination to bear on data that are subject to multiple interpretation from a strictly physical viewpoint. Likewise, those charged with the responsibility of planning seismograph exploration campaigns would do well to become familiar with as much as possible of the technical aspests of the work. They would then be in better position to judge of its success in individual cases. It has often been said that the seismograph is a new structure-finding tool for the geologists to use. Using a tool and using its product are two different things. One does not use an automatic screw-threading machine when he buys a box of screws at the hardware store. Neither does the geologist

Jan 1, 1940

By J. J. Davis, C. A. J. Fletcher, M. Li, T. Jancar

This paper summarises the experimental approach to spiral modelling at the Julius Kruttschnitt Mineral Research Centre, University of Queensland, involving the use of plastic density tracers to determine partitioning performance on three models of coal spiral. This work has led to phenomenological models of the three spiral profiles most widely used in the Australian coal industry. The results from a parallel computational fluid dynamics approach to spiral modelling currently underway at the University of New South Wales are also presented. The computational simulation has been successfully applied to generic spiral geometries and is capable of predicting the fluid phase three dimensional flow fields and corresponding free surface profiles for moderate Reynolds' number and Froude numbers. Simulation predictions are compared with experimental results from a Mineral Deposits LD9 coal spiral.

Jan 1, 1995

By C. Patrick

Annually, the US coal industry generates and must dispose of over 200 million st (180 million t) of coal refuse, expanding a major environmental problem. The purpose of this research was to investigate the feasibility of utilizing coal refuse as an aggregate in concrete. This paper reports on findings of the initial phases of a project to determine the viability of replacing traditional concrete blocks with refuse blocks for use in ventilation stoppings in underground mines. Refuse, collected from three active preparation plants in eastern Kentucky, was used as the primary as aggregate in the preparation of concrete cylinder. Stress-strain analyses on the refuse cylinders yielded compressive strengths of from 59% to 77 % of the control-group strengths. Low variability within the groups was found while significant differences between the groups existed. On-going determinations of the effects of weathering on the refuse cylinders is being conducted and will be completed in early 1995. The research results are favorable for the future direction of the overall project objectives.

Jan 1, 1997

By I Sheppard, A Hills

This paper describes a multi-lift bench stoping method introduced recently to extract the narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were chief mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The benching methods had improved both the economy scale and safety of the mining operation. The multi-lift benching method combines a number of bench lifts into a single stope to further improve the operational efficiency. Three stopes in the initial multi-lift benching trials are described.

Jan 1, 2003