Search Documents

SEC, 1, This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc,; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3, Associates; 4, Junior Associates. All members shall be equally- entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot, SEC. 2, Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in-addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years', employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership,' shall be considered equivalent to two years' employment, as required in the previous sentence, Employment as -a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility may be waived by the Committee on Membership in the case of persons who have done notable original work in mining, geology, or metallurgy, or have won distinction by research or investigations, in one or more of these subjects.

Jan 1, 1928

By R Crookes

Mine to mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian mining industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in Northern Queensland, Australia, has espoused the mine-to-mill concept and is actively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROM stockpile. A blasting improvement program was undertaken between Ernest Henry Mining, Thiess Contractors and Orica Explosives to optimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance of individual blasts are needed before it is possible to optimise fragmentation or the downstream processes. These include such specialised Orica Explosives tools as SABREX, POWERSIEVE, and POWERLINE and commercially available drill monitors. As important are the more common still and video camera, borehole loggers, measuring tapes, surveying equipment such as face profilers, and a high speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design -only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as the understanding grew and practices have been implemented resulting in reduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution. The continuous improvement program continues . . .

Jan 1, 1999

By D Giurco

This paper presents the results from research undertaken in the CSIRO-funded Mineral Futures Collaboration Cluster on developing a future vision for the mining and minerals industry – Vision 2040 – in which the industry proactively contributes to long-term benefit for communities and the nation. Our research finds that Australia is currently experiencing mining-led prosperity due to high commodity prices, yet underlying this are challenges for maintaining market share due to lower productivity from extracting lower grade, more remote and complex ores. Whilst much focus has been on developing new technologies for finding and processing such ores, this paper assesses these activities, together with policy and market innovations in the context of needing to strengthen social, environmental and financial capital for long-term benefit. Vision 2010 sees mining activities linked to systems that are net providers of clean water, energy and ecosystem services, rather than minimising negative impacts alone; sovereign wealth funds are used to harness current prosperity for future innovation. Using a case study in lithium and comparisons to iron/steel, coal and copper – we illustrate the opportunities for new technology, policy and market innovations to link the mining and minerals sector in Australia to more sustainable patterns of production, consumption and prosperity.

Nov 22, 2011

By R. E. Gilchrist, R. R. Harvey, M. R. Dean

A simple and rapid three-component analysis procedure has been developed for use in fluid-flow studies. The method is based on refractive index measurements, combined with refractive dispersion measured between the Ha and H wave lengths. The procedure requires. calibration curves for the three-fluid system. The only restriction on the fluids employed is that only one be an aromatzc or olefinic compound. Individual sample measurements require only a few minutes. Composition results within the limits of accuracy required for fluid-flow analog studies are obtained. INTRODUCTION The simultaneous analysis of three-component mixtures is a problem often encountered in fluid-flow analog systems. In petroleum production research, the problem is usually encountered in experiments on the displacement of fluid from a porous medium. In the case of immiscible displacement, simple volumetric measurements of the produced fluids are usually sufficient, the analog fluids often being the actual reservoir fluids themselves — oil, water and gas. However, modern secondary recovery of petroleum sometimes involves production under miscible conditions, in which the oil is displaced by liquefied petroleum gas which, in turn, is displaced by dry gas. Since this type of displacement is done under conditions of pressure and temperature that are not easily reproduced in the laboratory, studies are often performed with analog fluids at essentially atmospheric pressure. Since the number of samples taken during one of these experiments is usually quite large, the time required for analysis becomes an important factor. In the past, the difficulty of conventional analysis has been avoided by the addition of various tracers to one or more of the components, or by the use of a tracer fluid as one of the components. With these techniques, a relatively large amount of analytical time is still required. Moreover, in the case of added tracers, the tracer material may migrate in part to one of the other fluids, may be adsorbed on the solid surfaces of the model, or may introduce side effects not characteristic of the prototype fluid. The substitution of a tracer fluid for one of the components can severely limit the choice of analog fluids. Optical refractometry provides a rapid and economical method of analysis of two-fluid systems or of monitoring small changes in composition of an essentially one-component system. Refractometric methods are capable of high degrees of accuracy, require only very small samples and can easily be adapted to automatic methods. They are not generally applicable, however, where three or more fluids are present over wide ranges of concentration. The method of three-component analysis described here has three essential characteristics. 1. It is based on refractometric measurements and thus preserves all of these desirable properties. 2. It does not make any stringent demands on the choice of fluids that can be analyzed. 3. It is capable of accuracy sufficient for fluid-flow analog studies. THEORETICAL The difference in the refractive index of a substance at two different wave lengths of light is known as its dispersivity. When the difference is taken between the specific refractions at the two wave lengths, the quantity is referred to as the specific dispersivity. Specific refraction was defined empirically by Gladstone and Dale1 as r = n-1/d....[1] where n is the index of refraction and d is the density. The definition is given more correctly by the expression r =n2-1/n2+1 1/d..........(2) 1References given at end of paper. MICIFTV OF PETROLEUM ENGINEER JOURNAL.

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.' Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer's3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By Laxman M. Amaratunga, David N. Yaschyshyn

"In the mining industry several types of fills are used for backfill operations. They are broadly categorized into three basic types: rock fill, hydraulic/slurry fill, and paste fill. Recently, paste fill has become the popular alternative for backfilling because of its many environmental and operational advantages including its ability to use total tailings, both fine and coarse fractions.Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings, which are otherwise excluded from backfilling, for utilization in backfill as a readily available supplementary fill material. Previous experimental work investigated the use of agglomerated fine gold mill tailings in low density slurry fills (60 -70% pulp density), consisting of varying agglomerate and tailings compositions.This paper presents the ongoing research into utilizing these agglomerates in a high density paste fill (70 -85% pulp density). Various binder dosages, curing period and combinations of pellet to tailings ratios were studied. Slump of the raw fill and compressive strength of the cured fill were examined. Results from the above study indicate that agglomerated tailings paste fill (ATPF) has superior strength characteristics when compared to total tailings paste fills.IntroductionThe Canadian mining industry produces more than 500 million tonnes of tailings and waste rock annually. These tailings consist of a coarse fraction and a fine fraction and can be either reactive (acid generating) or non-reactive. Most mining operations utilize the coarse fraction for backfilling while the fines have been traditionally disposed of in surface tailings ponds. Recently, paste fill has been developed which uses a fraction of the fine tailings (10 - 30% w/w of >45 µ,m) in the fill. This development allows a mining company to use a portion of the fines for backfill, but still requires surface impoundment of the unused portion of fine tailings. Reactive tailings have the added problem of generating acid after being oxidized in the presence of air and water. Treating acid mine drainage (AMD) seepage from these ponds has proven to be a costly environmental problem and long term liabilty.One practical method to reduce the environmental impacts associated with the tailings pond and to modify the physical and chemical properties of the fine mill tailings so that they can be utilized and disposed of in an environmentally safe manner through surface or underground applications is through agglomeration using the Cold-Bond Tailings Agglomeration technology (CBTA). Amaratunga and Annor (1989) first presented the concept of agglomeration of fine tailings for use as coarse aggregates for underground backfill, gravel or surface covering material. CBT A reduces the necessity of impounding tailings on surface while providing a suitable coarse aggregate resource material for practical use. Although the CBT A technology has been mainly limited to pelletization agglomeration alone, other forms of agglomeration like pressure agglomeration which include the techniques of briquetting and extrusion have also proven successful (Amaratunga, 1995)."

Jan 1, 1996

By E. W. Davis

ABOUT a year ago several carloads of magnetite ore from New York state were sent to the Mines Experiment Station at the University of Minnesota for grinding and concentration tests. The flowsheet used minus ½ -in. ore as feed to a 3 by 3-ft. overflow cylindrical ball mill operating at 37 r.p.m. in closed ciruit with a vibrating screen. The screen oversize was returned to the mill for further grinding and the screen undersize was concentrated magnetically. Several different screens, between 8 and 35 mesh, were used and it was desired to determine the capacity of the ball mill operating in closed circuit with each screen. From earlier tests using this flowsheet and equipment, it was known that when comparatively coarse screens were used it was necessary to increase the grinding dilution in the mill beyond that ordinarily used when grinding in closed circuit with classifiers. It was also known that after the circulating load had passed about zoo per cent of the original feed it tended to increase rapidly in amount, and grinding conditions appeared to become unstable. These conditions may be peculiar to this small ball mill but they were very marked in this series of tests. If conditions were not right, the mill would suddenly "go dead," and it was found desirable to operate so that the occasional rattle of balls against the lining of the mill could be detected. As the test proceeded, it was found that the cure for almost any difficulty that developed in the grinding circuit was to add more water to the mill feed. To begin with, the mill was operated at pulp densities of from 60 to 65 per cent solids but gradually it was found that with higher dilutions grinding conditions were more stable and the ball-mill power per ton of screen undersize decreased. Actually, the most satisfactory operating conditions were secured with a pulp density of about 40 per cent solids. The ore was hard but it was possible to grind ½ in. feed so that all would pass an 8-mesh screen with a power expenditure in the ball mill of less than 2 1/2 kw-hr. per ton and with a circulating load of less than 50 per cent. With so high a dilution in the feed to the mill, it was feared that steel wear would be very high. However, the mill was not noisy, and in order to find exactly the grinding conditions, a special test was made at the end of the main series of tests. After the mill had been in operation for several hours and grinding conditions had become balanced, the power to all the equipment was shut off at a given signal. The ball mill made about one revolution after the power was turned off, and just as soon as the mill stopped, a spout was placed at the discharge trunnion and all of the pulp that flowed out of the mill was caught in tanks. The manhole in the mill was then opened and the whole mill charge dumped into other tanks. Both of these products were weighed, dried, and weighed again. The balls were screened out and weighed, and the dry solids were sized. In this way it was possible to determine the nature of the pulp and the ore within the mill under actual grinding conditions.

Jan 1, 1945

By M. F. McCarty, R. S. Olson

New organic flocculants of high-molecular weight are replacing lime, glue, and starch in liquid-solid separation. Of these synthetic materials, poly-acrylamides are outstanding. Polyacrylamides form a class of compounds varying widely in composition and activity. Separan 2610, one of the first of these flocculants' released to the mining industry in 1954, is described' as a high-molecular weight polymer of acrylamide with or without a copolymer material and with some replacement of amide by carboxylic groups. MECHANISM OF FLOCCULATION In practice, flocculation makes solids settle faster and filter better. But two opposing factors control it. The random motion that causes particles to collide favors Van der Waals' forces, which hold the particles together. The effect of zeta potential opposes this contact, and particles are mutually repelled. Flocculation can be achieved by reducing the magnitude of the zeta potential; this is the mechanism of flocculation by lime addition. The way in which polyacrylamides accomplish flocculation is not fully understood, but the action is undoubtedly comp1ex and probably varies considerably depending on the system. To begin with, the active groups of these compounds have an extremely high affinity for solid surfaces, probably by hydrogen bonding." Initially some active groups of the molecule attach themselves to the solids with a large portion of the molecule extending into the solution. Two particles can become tied together by long flocculant molecules in the following ways—by bonding between the active groups of two flocculant molecules on different particles, or by an extended molecule from one particle attaching itself directly to the surface of the other particles." These flocculant bridges prevent the particles from moving apart through random motion, but when such motion moves them together other active groups on the flocculant bridge bond to the solids, holding them in the closer position. This process is repeated until the particles are close together. Although bridging is probably a major flocculation mechanism, it is not the only phenomenon involved. Relatively neutral acrylamide flocculants reduce the magnitude of the zeta potential by increasing the viscosity of solution in the immediate vicinity of the solid surface which contains the mobile counter ions of the double layer. In other words, it moves the shear surface which bounds the zeta potential out into the solution containing counter ions which tend to neutralize the zeta potential. This effect is probably more pronounced during the initial adsorption period, before the flocculant molecules are pulled close to the solid. In some cases the slight charge of the polyacry-lamide molecule tends to neutralize a zeta potential. However, this is not a primary flocculation mechanism, as evidenced by the fact that the polyacrylamides will flocculate solids with either positive or negative zeta potential. Adsorption of polyacrylamide flocculants by a solid is substantially an irreversible reaction. Since the flocculant molecule is attached to the particle surface by many active groups of high bonding strength, desorption would require the simultaneous breaking of many bonds—an unlikely occurrence. UNIQUE PROPERTIES The irreversible adsorption of certain polyacrylamides, the flocculant's high affinity for solid surfaces and its rapid adsorption make it effective, but these unique properties require special techniques to achieve maximum flocculation. If flocculants of this type are added to a pulp as a relatively concentrated solution, the solids in the

Jan 1, 1960

Introduction The Coal Mine Roof Rating (CMRR) is a roof classification system. It was first introduced to the mining community in 1994.The CMRR filled a longstanding need to quantify geologic description of coal measure rocks into an engineering value that could be used for mine design. It has now been written to a user-friendly visual basic code that can be run on any PC with a Windows operating system. Background Rocks that form the roof of coal mines can vary widely and quickly in composition, extent, and defects. This results in an equally broad range of rock properties that can substantially affect the ability of the rock mass to form a stable mine roof. The CMRR was designed to evaluate the properties of the coal mine roof rock mass that contribute to its weakness and convert them into a relative strength rating from 0 to 100. These properties include the cohesion and frequency of discontinuities like bedding, slips, shears, and joints; uniaxial compressive strength (UCS); and moisture sensitivity. With simple lab and field tests and observation, the CMRR can be calculated by technical and operating personnel with a minimum of training. The CMRR has been widely accepted in both U.S. and international coalfields. As a result, a number of roof control applications have been found for the CMRR. It is currently used as an input component in the Analysis of Longwall Pillar Stability(ALPS) program, which is used to design longwall chain pillars. Incan be used as a criterion for determining the appropriate width of mine entries. It has also been used to indicate the appropriate length of cut in weak ground. The CMRR can be used as a strength parameter to characterize inter burden between mined seams in the numerical modeling of subsidence effects. In any area where an estimation of coal measure rock mass strength is required, the CMRR can be adapted to fill this need. How It Works Originally designed to be used with underground exposures, the CMRR can also be calculated from core. The chisel test for bedding cohesion and the ballpeen hammer test for UCS are inappropriate for core. These tests have been replaced by point load testing both axially and diametrally. Two other measures that are common to standard core logging—Rock Quality Designation (RQD) and fracture spacing—are also used to estimate rock weakness. With these easily obtained parameters, the CMRR can be calculated from core and used in the mine planning and exploration phase. The input screens allow calculation of the CMRR for both underground exposure and core. The CMRR is reported both as a “dry" value and as a groundwater-adjusted value for moisture-sensitive rocks. There is a graphical output report featuring a lithologic column with annotated unit ratings and a roof bolt symbol representing the height of the bolted horizon. Another important feature is an AutoCAD interface. This feature allows the export of located CMRR data directly to an AutoCAD layer in XYZ form. In this way, drill hole data can be inserted directly to a base map.

Apr 1, 2003

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By Mortimer J. Richardson, Earl H. Malmstrom

INTRODUCTION The art of placer gold mine evaluation and mining has had an interesting evolution beginning in earliest times. DE RE METALLICA (c.1556), documents the use of rockers, circular sieves(jigs) and riff lest for classifying, concentrating and recovering placer gold, respectively. During the late 1800's in the heat of the international gold rush, a bucket ladder mining dredge containing its own processing plant was developed that enabled digging of placers to bedrock that were inaccessible to the hand miner. The power driven churn drill was developed at about the same tie that facilitated more rapid and larger scale sampling of placers to bedrock. The mineral jig was applied in the early part of the 1900,s to begin the replacement of riffles on placer dredges. Mining dredges proliferated in California and New Zealand to mine the deeper placers and spread throughout the world. The companies that were leaders in dredge mining technology conducted experimental work that advanced the state of the art by processing of gravels with jigs and amalgam systems to recover gold on board dredges in a continuous process. This paper will synthesize the technology of placer gold exploration, mine development and operation into guidelines for evaluation and development of small-scale prospects. Prospect Reconnaissance The location of a prospect usual1 y results from some physical evidence of the presence of gold and/or past mining activity. Any earlier activity that may have produced gold from the prospect, should be investigated before making the trip. The initial reconnaissance should attempt to verify a near-surface presence and then make observations concerning the geomorphic characteristics that relate to placer gold accumulation. Estimates of the probable depth, breadth and length of mineable gravels can be made from the surf ace by the experienced placer mining engineer. With this information, he can speculate on whether there is a viable prospect to be pursued. The placer mining engineer should be experienced in panning samples found in shallow diggings or from existing pits. This will give him immediate indications of gold presence without fear of "salting" by an over-ambitious promoter of the project. The same capability of panning is important during the other sampling phases. A thorough knowledge of logging and calculating the results is essential to proper evaluation of the deposit' s tenor. Evaluation Methods Depending upon the character of the prospect such as river, benches, terraces, jungle, the type of equipment to conduct sampling of the deposit must be determined. In most cases, the drill has replaced bulk sampling. The churn drill has had the greatest amount of accumulated experience but is slow. The reverse circulation drill (RC), is limited by its lack of verification in subsequent mining in order to prove its reliability. However, in the hands of knowledgeable placer mining engineers experienced with its use and calibration, it may be used. The RC Hammer drill (such as the Becker), can be as much as ten times faster than the churn drill and compress the time necessary to prove a prospect, or, to disprove it. All costs in balance, it is often cost effective over the churn drill.

Jan 1, 1987

By Tevfik Güyagüler

Airborne dust is one of the important environmental problems in mines. Besides conventional dust control methods, recently, extensive studies have been carried out on the elimination of dust before it has actually been formed. Determining to what extend rock characteristics influence the amount of dust produced during different mining activities are considered as a guide for this purpose. The factors analyzed in this study were main mechanical, physical properties and petrographical constituents, namely free and combined silica. In the study regression analysis techniques were applied to investigate the effectiveness of aforementioned factors. INTRODUCTION Nearly every aspect of mining activity contributes to the air pollution caused by dust. Therefore the harmfull effect of airborne dust has been investigated many years and limit dust concentration levels were determined for various types of mine dust. To keep the dust level below limit value different dust control techniques have been applied in mines. So far, the well known techniques regarding dust control focuses on reducing the amount of airborne dust. However, recently various studies have been carried out to avoid the dust before it has actually been formed (Bhaskar and Gong, 1991). In this respect, influence of rock characteristics on dust formation is regarded as a guide for this purpose. The present contribution describes such a study in which the drilling operation is considered as the source of the dust. In this study drilling and dust sampling process were undertaken in a model gallery that simulates an underground working. The mechanical and physical properties of the rock samples were measured in rock mechanics and ore dressing laboratories. Quartz and combined silica contents of the rock samples, on the other hand, were determined in the laboratories of geological engineenring department. Rock samples used in the research were different types of coal measure rocks, namely, sandstone, shale and conglomerate. The rock characteristics studied in this work are brittleness, toughness, rock strength, hardness and hardgrove index as inherent properties; free silica, and total silica contents of rock samples as petrographical constituents. Although there have been various studies to determine the effect of rock characteristics on the dust formation, still the type and extend of effectiveness have not been understood clearly. LITERATURE REVIEW Most of the studies investigating the effect of rock properties on dust formation concluded that they are effective. In such an investigation, it has been found that inherent rock properties influence dust formation (Das, 1973). In the another study, dustiness of the air was considered as a function of the composition, hardness and moisture content (Panov, 1967). It was also accepted that in a drilling operation more fine dust is produced if the rock to be drilled is hard (Skochinsky and Kamarov, 1969). In some other investigations dust production were considered as a function of hardgrove index (Moore and Bise, 1984) or formulated in terms of brittleness, toughness and hardness (Güyagüler, 1991). The effect of the petrographical properties of coal or rock on dust formation characteristics have also been studied (Baafi, 1979) (Panov, 1967). Because of its importance, various researches were conducted the study to find out the effect of free and combined silica content of dust on dust formation. In one of the study, the relationship between quartz in the coal seam and quartz in the airborne coal dust was investigated (Ramani et al, 1988).

Jan 1, 1993

By H. Buttner, F. H. Udin, J. Wulff

GRAIN boundaries, the interface between adjacent crystals differing only in respective orientation, have been the object of much experimental and moderate theoretical attention for many years. The earlier experimental work was primarily concerned with the effect that grain boundaries have on the physical behavior of metals, while the basic nature of the boundaries themselves drew only secondary attention. A complete turnabout has been witnessed in more recent years, however, as researchers are now undertaking investigations bearing as directly as possible on the character and physical properties of the grain boundary. Quite comprehensive reviews of the past literature on the subject of grain boundaries have been reported on numerous occasions by various authors, and together these references represent a thorough coverage.'-? It becomes evident in these reviews and other papers"" that the properties of grain boundaries can be explained by regarding a grain boundary as a crystalline region of transition between two unmatched grains. Studies show that grain boundaries have a definite interfacial energy. By measuring the geometry about a point where three interfaces meet in equilibrium, the energy of any two boundaries can be measured with respect to the third. If the absolute interfacial energy of one boundary is known, the absolute energy of the other two boundaries can be calculated. This apparently holds true for any system of phases and interfaces.""25 Most studies have been carried out on solid-solid or liquid-solid systems, or systems of both. However, if about the point of intersection one phase is vapor and the other two are disoriented grains, then two interfaces are surfaces, and one is a grain boundary. Investigations leading to relative grain boundary energy for this particular system have been made by Fullman,23 Greenough and King," and Bailey and Watkins." Herring" treats the system mathematically and arrives at an equation, which appears as Eq. 1, in a form consistent with the reference angles indicated in Fig. 1, ( d?1 ?n = x sina + cosa ( ------- 2 ?2 Sinß da + C0Sß (d?2/d As the system of interfaces comes to equilibrium, a groove of angle appears at the intersection of the grain boundary with the surface, an effect first observed by Rosenhain and Humfrey." Eq. 1 is essentially a summation of the vertical components in Fig. 1 set equal to zero, where ?1 and ?2 are surface tension vectors lying along the side of the groove at point 0 in the groove root. The differential vectors represent the forces tending to rotate the surface into a position that will expose a crystal cleavage surface of lowest energy. Chalmers, King, and Shuttleworth- simplify Eq. 1 by assuming the differential vectors equal to zero, ?1 = ?2= ?Surface and arrive at the following equation: ?B = 2?s cos [2] Greenough and King24 use Eq. 2 for determining the grain boundary energy of silver using prepared bi-crystals of known orientation. Bailey and Watkins25 have done the same for copper, as did Chalmers and others on lead. These authors report the grain boundary values as ratios relative to the surface energy. In the above work, the orientation of grains forming the grain boundary in all cases was controlled so

Jan 1, 1954

By Esau Arinaitwe

The most extensively used methods and approaches for characterizing and selecting frothers for plant application are based on measurements in clean water in the absence of solids and without consideration of physicochemical factors that are known to influence the properties and behavior of practical flotation froths, and hence metallurgical performance. These factors include aquatic chemistry, collectors, modifiers, particle shape and size, and pH. Understanding interactions between these factors and the role and relevance that they play in characterizing frothers and froth zone properties will greatly aid in the frother selection and evaluation process. Such an understanding will also greatly enhance the ability to create frother solutions that are sufficiently robust to plant variability (such as mineralogical, comminution, operational, physical and chemical). This paper reports results of a “systems approach” study designed to probe ways in which physicochemical factors a) influence frothing and bubble size in 2- and 3-phase systems, and b) confound correlation of fundamental measurements with flotation outcome. The concepts and insights gleaned from fundamental frother studies, together with empirical laboratory flotation tests and a thorough understanding of plant needs and challenges were used to develop and implement customized frother formulation at a Cu-Mo flotation plant. Plant metallurgical data and qualitative assessment of froth zone properties showed that a frother formulation developed using the approach described here provided marked improvements in froth characteristics (mineralization, mobility, stability, persistence). These improvements resulted in better circuit control and significant performance advantages, such as improved coarse particle recovery, without detrimental downstream effects. INTRODUCTION Successful recovery of value minerals of sufficient grade via the flotation process requires selective manipulation of the value minerals to render them hydrophobic using collectors and modifiers. The hydrophobized minerals then attach to air bubbles and the mineral-bubble aggregates are selectively transported through the froth zone into the launder. Frothers play a critical role in froth formation and more importantly in achieving and maintaining desirable froth characteristics (for example, stability, mobility, persistence) that are essential in facilitating the selective transport and recovery of value minerals. Fundamentally, frothers contribute to the transient stability of thin liquid films and so aid in reducing bubble coalescence rates in the pulp and froth zones, thus maintaining the small bubbles required for efficient bubble-particle attachment. Invariably, the action of frothers at the liquid/gas interface in the pulp and froth zones impacts bubble stability, water and solids transport to the froth, which in turn impacts froth mobility, froth carrying capacity, and the concentrate grade. Consequently, selection and evaluation of frothers for flotation plants requires careful consideration of the frother type, though the choice is limited to only two main classes of compounds in terms of fundamental chemistry (short chain alcohols and polyglycols). Even with the selection of what is thought to be the best frother for a given application, practical knowledge of the froth zone and experience in controlling its properties is essential for maximizing metallurgical performance.

Jan 1, 2019

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

INTRODUCTION IN a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. 10-18,20,21,23,[1] Consequently since a technical cohesion limit is defined as the technically determinable resistance to fracture, under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,§ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit; the authors are here using the' shorter term with the understanding that it, does not always refer to actual fracture. In the general investigation described. in the previously-mentioned papers,10-18,20,21,23 the influence of the stress 'system on the fracture stress was studied by means, of tension tests of notched specimens. When a circumferentially notched cylindrical' specimen is subjected to longitudinal ten-, sion, the minimum cross section is under " transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S,), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (S2 = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (S3/SI). The evidence is based not only on the results of tests to fracture at various constant temperatures, but also on. results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1948

By R. B. Ladoo, C. A. Stokes, R. N. Secord, A. L. Hall

INDUSTRIAL mineral history shows that the entrance of new, nonmetallic minerals into commercial production can be expected to occur from time to time. Latest entrant into the field is wollastonite. Except for one short-lived period in Kern County, Calif., starting in 1933, wollastonite has never before been produced on a commercial scale. But the signs are up for its entrance as an economic factor in the mineral market. Small scale experimental production from a deposit near Willsboro, N. Y., started about 1943. A pilot plant was built in 1949-50 and irregular, small scale, production has continued. In early 1951 Godfrey L. Cabot, Inc. of Boston, world's largest producer of carbon black, took an operational lease on the property to study the deposits and make market surveys. This became Cabot's first venture in the mineral field, when they took over operations and began design of a new mill, expected in production in 1953. Properties The properties and major uses of wollastonite are comparable to New York fibrous talc. It has about the same specific gravity and index of refraction as talc, but is somewhat whiter and softer. The two most important fields of use, paint and ceramics, are the same as for talc. Ground wollastonite has a fiber length as much as 13 to 15 times the diameter. This particular property makes it applicable in the paint field and others. In addition, the length-diameter ratio may be controlled to rather narrow limits by choice of grinding method. Another important commercial property is brightness or whiteness. Wollastonite reads from 92 to 96 pct of MgO on the G.E. brightness meter for a 99 pct -325 mesh grind. Purity and uniformity of product are important. Chemically, the wollastonite now being mined analyzes SiO2 51.76, CaO 47.56, FeO 0.46, MnO 0.04, and H2O 0.09 pct. Theoretically pure wollastonite analyzes SiO2 51.75 and CaO 48.25 pct. This analysis indicates over 98 pct calcium silicate, with only small amounts of contaminating ingredients. That these ingredients are not detrimental to color or brightness is shown by the high brightness value of the fine ground material. [ ] By-product calcium silicate from electric furnace production of phosphoric acid has little physical re-semblance. to this wollastonite, being an off color white, and lacking in fibrous crystalline character. Minerology Wollastonite is a calcium metasilicate, CaSiO3, a white, medium hard, fibrous mineral. In this deposit wollastonite occurs as well crystallized aggregates of bladed crystals intergrown with garnet, and with a few percent of green diopside. The beneficiated product is about 75 pct wollastonite, 15 pct garnet, and 10 pct waste, largely middling. Wollastonite-garnet ore occurs in at least two beds. The main bed, varying in true thickness from 30 to 70 ft, dips into the hill at an average 30° and is enclosed in gneisses. Diamond drilling has proven the orebody to an average depth of 200 ft along 2000 ft of outcrop with adequate tonnage for many years of quarry operation. The wollastonite-garnet ratio varies locally, but average composition is uniform over long distances. A friable ore, it is easy to drill, shoot, and crush. Beneficiation Unlike talc this ore has to be beneficiated. Successful treatment depends upon the fact that it contains virtually nothing but wollastonite, garnet and a minor percentage of diopside. A very pure wollastonite product can be made by high intensity magnetic and/or gravity separation methods.

Jan 1, 1952

By J. Chipman, N. J. Grant, J. C. Fulton

This paper contains data on the distribution of silicon between liquid iron-silicon-carbon alloys saturated with respect to graphite and CaO-SiO2-Al2O3 slags under 1 atm of CO at 1600°C. The ranges of slag compositions studied were extended from the dicalcium silicate saturated liquidus composition up to silica concentrations at which Sic appeared as a stable phase. IN blast furnace operation it is not to be expected that slag and metal reach equilibrium with one another. Nevertheless, the silicon content of the metal varies with slag composition and with temperature in a manner which would be predicted from equilibrium considerations. Similarly, the distribution of sulphur between slag and metal does not attain an equilibrium state, yet the influence of slag composition is strongly analogous to its effect on the distribution equilibrium. The desulphurizing power of metallurgical slags has been shown to be highly dependent upon the FeO content of the slag. Moreover, the rate of removal of sulphur from slags is influenced by the oxygen potential of the slag-metal system. Thus it was shown by Grant, Kalling, and Chipman1 that the presence of MnO in slags which are low in FeO causes a marked slowing down of the transfer of sulphur from metal to slag. This led to the hypothesis that the slow removal of sulphur by blast furnace slags of more acid composition might be due in part to the effect of SiO2 on the oxygen potential of the system. This was verified in the work of Grant, Troili, and Chipman,' who found that the desulphurizing power of the more acid blast furnace slags could be markedly improved by an increase in the silicon content of the underlying metal. Their explanation of this improvement was that the higher silicon content of the metal decreased the rate of transfer of more silicon and, along with it, of oxygen from the slag to the metal. The slowness of the transfer of sulphur from metal to slag was the result of the slow reduction of SiO2 from slag to metal. Attempts to study the rate of sulphur removal had in the past resulted in very slow rates corresponding to the rates of silica reduction. It has become evident on the basis of these studies that further experimental studies on the rate of removal of sulphur must take these factors into consideration if there is to be a clear understanding of the rate of sulphur transfer under conditions simulating those existing in the blast furnace. It will be necessary, at least in a part of such study, to employ combinations of slag and metal in which the disturbing effect of silica reduction has been eliminated; in other words, to employ slag-metal combinations which are already in equilibrium with respect to the transfer of silicon. In preparation for such studies of desulphuriza-tion, a preliminary program of research on the distribution of silicon between slag and metal has been undertaken. This will ultimately include a comprehensive survey of the effects of temperature and slag composition on the equilibrium distribution of silicon between slag and metal. The present paper is a report on experimental methods employed and on

Jan 1, 1954

By J. P. Newell, R. W. Storey

AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery .augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120 This head design proved to be very satis-

Jan 1, 1952

By Henry Drinker

The Institute has lost a valued member by the death of Eckley B. Coxe, Jr. He bore the name of one who was largely instrumental in founding the Institute, and to whose support and guidance as active member, Vice-President, and President, the Institute owes. much. Eckley B. Coxe, Jr., was the nephew of the late Eckley B. Coxe. He held a large interest in the coal estates owned and developed by his family, and he was thus naturally led to take a continuing interest in mining matters, and for years and up to the time of his death was a full member of the Institute. He died at his residence, Drifton, Pa., on Sept. 20 last, aged 44. He was a member of the class of '93 of the University of Pennsylvania,. of which great institution he was a devoted alumnus. His educational and charitable activities were numerous, but his chief life-work and interest was in archeological investigation and research in Egypt, carried on through the Museum of the University of Pennsylvania of which Museum he was President. The discoveries made by the various expeditions financed and directed by him, and the notable publications issued by his direction and at his expense, chronicling the results, are among the most important researches ever made of buried Egypt. Mr. Coxe was a member of the International Historical Society and of many educational and charitable organizations. By his will, among other bequests, he left $500,000 to the Museum of the University of Pennsylvania and $100,000 to the University, the income of the latter fund to be applied to increasing the salaries of the professors of the Institution. He also left $100,000 to the Children's Hospital of Philadelphia, of which he was a manager, and in addition thereto $10,000 of which the income is to be applied in providing Christmas presents for .the child patients, and in providing an annual dinner for the patients and attendants of the hospital. He bequeathed $50,000 to Leonard Hall, an associate mission of the Episcopal Church, at South Bethlehem, Pa., $25,000 to the Epileptic Hospital and Colony Farm (Philadelphia) ; $50,000 to the Philadelphia Orthopaedic Hospital and Infirmary for Nervous Diseases; $15,000 to the United Charities of Hazleton, Pa., the income to be applied to the salaries of nurses; and $25,000 to the Mining and Mechanical Institute of the Anthracite Coal Region of Pennsylvania, founded by his uncle, Eckley B. Coxe, and of which Eckley B. Coxe, Jr., was an active trustee up to the time of his death. This Institute is known as one of the best preparatory schools for technical education in Pennsylvania, and is mainly devoted to extending an opportunity for education by day and night schools to the boys and young men of the Anthracite Region. Its principal is an alumnus of Lehigh University; it has an able local Board of Trustees, and an Advisory Board consisting of the Provost of the University of Pennsylvania, the President of Lafayette College, and the President of Lehigh University, all three of which institutions have established prize scholarships in the institute. Mr. Coxe carne of a distinguished ancestry, the record of which is fully given in the biographical notice of his uncle, Eckley B. Coxe, by Dr. R. W. Raymond, in Vol. XXV of the Transactions.`

Jan 12, 1916