Search Documents

By L. C. Headley

Surface areas of two synthetic and three natural consolidated porous samples were obtained by the Orr low-pressure permeametry technique. The results suggest that the Orr technique is a useful substitute for the low-temperature gas adsorption (BET) method for determining the surface area of rock samples. It was more rapid than the BET method, and the surface-area values obtained were larger but agreed better with BET values than values calculated from the Kozeny-Carman equation. Efforts were unsuccessful to demonstrate the influence of channel-size distribution on pressure-flow rate curves by means of experimental data and a parallel channel model.

Jan 1, 1971

By C. Van Rhee

In dredging practice sand is eroded at very high flow velocities using water jets. The existing pick-up functions overestimate erosion. By taking the permeability into account conventional pick-up functions can be made suitable for high velocity erosion. This can be achieved by modifying the critical Shields parameter. The procedure is demonstrated using the pick-up function of Van Rijn. The theory is compared with experiments and agreement is good.

Jan 1, 2007

By J. H. Keeler

AN alloy of zirconium containing 18 atomic pct Cb was found to be body-centered-cubic and readily deformable at room temperature. The behavior of this alloy provided an opportunity to determine if

Jan 1, 1957

MINING; SOLUTION U.S. 4,066,297 - In the solution mining of uranium from an underground deposit of uranium ore using an alkaline leaching solution, precipitation of alkali metal salts is avoided by maintaining the Injected leach solution of an alkaline carbonate or bicarbonate and an oxidant undersaturated with respect to carbonates Undersaturation is effected by use of a water softening unit or by bleeding a portion of the recycled alkallne leach solution. A P. Spence, assigned to Atlantic Richfield Co Jan. 3, 1978 4 pp. (299-4). Filed: 6-1-76 (69 1,344)

Jan 1, 1979

By Richard Dooley

This paper is one sided because it presents the problem, but not the solution. The problem of blisters (bubbles) and occasional tears in caisson liners occurred when blasting and we have not found a conclusive cause nor a preventive solution. (For back ground information, consult Techniques of Precision Blasting in the Excavation of Drilled Piers, by George Mosteller at the Sixth Conference on Explosives & Blasting Technique in Tampa, Florida 1980).

Jan 1, 1983

By Ron Galisky

Generalmente, las empresas mineras deben decidir si reemplazan los equipos anteriores por unos nuevos o continuan con los mismos . Los criterios se basan en el nivel de deterioro, cambios tecnológios, demandas medioambientales, o cambios de requerimientos. En ese sentido, el presente texto describe la metodología adecuada para la gestión de cambios de equipos a través de la teoría clásica del CAE donde se abordan tales problemas. Así también se plantea el uso del modelo CRU Strategies. La metodología ayuda en la planificación y gestión operativa y en los presupuestos de inversión anuales típicos en la industria.

Mar 1, 2012

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, Ronald J. Roman

The hydrodynamics of the leaching solution in leach heaps is known to be one of the important variables in the performance of the heap. The solution hydrodynamics are also important in the decommissioning of a heap where the aim is to flush out the residual dissolved metals and the remaining reagents. Chemical engineers have studied the hydrodynamics of "trickle bed" reactors for 40 years in an attempt to relate the performance of trickle bed reactors to flow conditions. Their work is reviewed with emphases on areas of similarity to heap leaching.

Jan 1, 1993

The electrochemical dissolution of gold and other noble metals in hydrochloric acid using alternating current has been investigated. The experimental results show that this technique is efficient for dissolving pure noble metals and offers prospects for their extraction from wastes and poor ores.

Jan 1, 1992

(This list includes only those who have entered military service within the past month, or whose entry has only recently become known to us; it also includes a few names of those whose titles or assignments have been changed within the month. The last complete list was printed in Bulletin No. 131, November, 1917. A complete Honor List is maintained in the reception room at the office of the Institute:) AARONS, J. BOYD, Captain, 4th Reinforcements, 11th Infantry, Australian Imperial Force. AHBE, F. R., Captain, 33d Engineers. AMBLER, HARRY A., 30th Infantry, Camp Greene, Charlotte, N. C. ALFORD, NEWELL G., Sergeant, Headquarters 84th, 9th Division, Camp Zachary Taylor, Ky. ANDERSON, ALEXANDER, Lieutenant, Royal Garrison Artillery. ANDREWS, CLARENCE W., 1st Infantry Co., Officers' Training Camp, 83d Div., Camp Sherman.

Jan 2, 1918

Allow miners to communicate via the pagerphone system when they are not near one of the phones. Approach A small lightweight pagerphone, having crocodile clips which pierce the phone line insulation, was developed. How It Works The Portable Telephone/Intercom is temporarily clipped onto an existing pagerphone line at any location, and operated like an intercom. It is riot necessary to strip the insulation from the pagerphone line to make the connection. In addition to the clips for connecting to pagerphone line, the Portable Telephone/Intercom consists of a small belt-carried control box, an ear-phone, and a bone-conduction microphone which is attached to the webbing in a miner's helmet. All together, these components weigh only 20 ounces including the batteries

Jan 1, 1977

By G. G. O. O. Uwadiale

A number of Nigerian iron ore deposits have been upgraded to the specifications of concentrates for the blast furnace and the direct reduction iron- and steel-making plants. Depending on the mineralogy of the ore deposits, the techniques of oil agglomeration, magnetizing reduction, washing and scrubbing, gravity concentration, and reverse froth flotation have been utilized. A mode of distributive management of the deposits, in the direction of their technoeconomic utilization in the country's developing iron and steel plants, is presented.

Jan 1, 1990

By Paul M. Godlewski, Gerry Millar, Harvey W. Parker

Recently, over 70 railroad tunnels in the western USA have been enlarged and rehabilitated "live track," utilizing modern excavation and lining methods, in most cases to clear the larger double-stack container cars. This paper presents the general conditions of the tunnels and the technical aspects and costs of the rehabilitation of approximately 40 kilometers of tunnels, which range in length from a few hundred meters to 13 kilometers. Concrete-lined tunnels were rehabilitated by grouting and rock bolting, while unlined or timber-supported tunnels were relined with shotcrete and rock bolts. High output lining methods were required because of limited track time. Enlargement has been accomplished primarily by carving notches out of the concrete linings with a roadheader, or occasionally with saws. Unlined tunnels were enlarged by drill-and-blast or roadheader excavation.

Jan 1, 1991

By R. J. P. Lyon

It is usually assumed1,2 that ore deposition is relatively slow, taking place over tens of thousands of years. Yet many syntheses and phase changes can be completed in the laboratory in a matter of hours, under essentially the same pressure and temperature conditions to be expected in nature. Much has been written about geothermometry, and Ingerson's recent summary2 can hardly be surpassed. Rather than review the whole field, this article will deal specifically with diffusion rates in solid solutions* of the sulfide minerals.

Jan 11, 1959

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period May 10 to June 10: Rene de Sallier, New York, N. Y. Karl Koelle, San Luis Potosi, Mexico. H. S. Chamberlain, Chattanooga, Tenn. W. A. Wilson, Salt Lake City, Utah. F. R. Pretyman, Oyster Bay, N. Y. P. E. Barbour, Candor, N. C. R. Eustice, South Australia. R. C. Blanchard, London, England. F. C. Darby, South Australia. S. K. Tong, Shanghai, China. Grant H. Tod, Livermore, Cal. W. T. Burns, Great Falls, Mont. J. Murray Clark, Toronto, Canada. F. W. Bacorn, Butte, Mont. J. H. Adams, Birmingham, Ala. H. B. Pulsifer, Chicago, 111. A. Faison Dixon, Encontrador, Venezuela. Dwight E. Woodbridge, Duluth, Minn. C. W. Merrill, San Francisco, Cal. Heinrich Ries, Ithaca, N. Y. Francis Church Lincoln, Boston, Mass. H. L. Slosson, San Francisco, Cal. Frank R. Corwin has severed his connection with the Arizona Copper Co., Clifton, Ariz., and is now shift superintendent at the smelting plant of the Copper Queen Consolidated Mining Co.. Douglas. Ariz.

Jan 7, 1914

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

Terminology Relating to Nonmetallic Elements in Metals. See IRON AND STEEL Ferromagnetism in Metallic Crystals. BY L W MCKEEHAN (Tech. Pub 554, Metals Tech , August; also Trans, vol 111. 20,500 words ) The directions for easiest magnetization of ferromagnetic single crystals are those of simple crystal- lographic forms and the extra energy needed for magnetization in other than these preferred directions depends upon the material selected for test The history of magnetic tests upon metallic single crystals, reviewed in detail, shows that crystals of one metal agree rather well as to the magnitude of such energy differences. This makes ~t probable that these differences are really charactenstic of the ferromagnetic

Jan 1, 1935

By Rixford A. Beals

It has been observed with considerable accuracy that if the major U. S. mines were moved to Mexico tomorrow, many of them would be losing money. But the companies would continue to operate, losses or not, because they would have to. And some of the newest and most promising low grade ore projects in the U. S. would never have "gotten off the ground" had they faced the equivalent of the mining taxes now in effect in Mexico. No one of the various mining taxes in Mexico seems prohibitive by itself. Taken together, on the balance sheet, however, the picture changes. Production and export taxes alone take from 20 to 40 pct of the gross product value for base and precious metals.

Jan 2, 1955

By B. K. Mishra, A. Datta

Estimating the power draw of a ball mill is of great importance from both operational and control standpoints. There are many factors that affect the power draw, and its prediction is particularly difficult in an operating plant. The important factors that affect power draw are the mill dimensions and operating parameters. Although mill dimensions remain the same for any given mill, the operational factors, such as ball load, mill filling and mill speed, may vary. This makes the modeling effort extremely cumbersome. It is for this reason that an artificial neural network is considered for the development of a black-box-type model to predict power draw. In this work, a total of 48 sets of plant data are used. Using these data, a neural network is built and trained. The trained network is used to predict power that is found to be in good agreement with operating mill power for many situations. In addition, the results of simulations are also com- pared to those obtained from a discrete-element method- based power-draw model.

Jan 1, 2000

By John O. Marsden

The project development metallurgist is faced with an interesting dilemma: The use of overly conservative metallurgical projections and cost estimates can kill a project that has the potential to provide needed jobs and growth to a company's bottom line. On the other hand if the metallurgist uses a highly aggressive approach by trimming capital and operating cost estimates to the bone and by applying highly optimistic metallurgical projections, there is a risk of creating a project that can never live up to expectations. The metallurgist must walk a tightrope between "sandbagging" and "overoptimism," and this tightrope is fraught with political intrigue and difficulty. This paper takes a some- what lighthearted look at some of the political aspects associated with this issue, and other issues, and offers a few guidelines for walking the "political metallurgical" tightrope.

Jan 1, 2001