Search Documents

By K. Hodgson, N. C. Joughin

The detailed mechanism of rockbursts and other forms of damage due to rock failure in underground mining is as yet unknown. Studies of the energy changes which necessarily occur when an excavation is made underground seem to provide the best understanding of the phenomena leading to rock failure and damage (see Cook 1). It is common knowledge that the damage and rockburst hazard increases with depth and is greatest at remnants and in regions mined in an irregular manner. The rate at which energy is released as an excavation is enlarged provides an objective parameter to describe mining geometry in terms which are significant to studies of rock failure. In this paper, it is shown empirically that the rate of energy release per unit area increase in the size of an excavation is closely related to seismicity and incidence of damage in the mine. Consequently, it is suggested that the energy release rate is an important parameter in the design of underground mine layouts. Observations were made at two mines: the East Rand Proprietary Mines, Ltd. (E.R.P.M.), at a depth of about 9000 ft, and at Harmony Gold Mining Co., Ltd., at a depth of about 5000 ft. At both of these mines continuous recording seismic networks were in operation. (See Cook and Joughin.3) DESCRIPTION At E.R.P.M. the gold-bearing reef dips at approximately 35 degrees and is presently being mined at depths from 8000 ft to 11,000 ft below surface. The rock surrounding the excavation consists of a very homogeneous quartzite extending far into the hangingwall and footwall. The stoping width is approximately 40 in.

Jan 1, 1967

By Sinha DK

Coal Mining in India had been confined in the past primarily to two or three coalfields. Unscientific mining has led to huge degradation of land including massive subsidence of strata and disturbances of water tables to a wide extent. This has caused problems not only in flooding of mines from surface water but also in further planning of the surface drainage for current mining activities. Now, therefore, surface hydrology and land-use potentialities of the area have been endangered inflicting severe damage to the overall environment and ecology of the area. The paper Discusses certain investigative aspects of the problems highlighted as above in one of the coalfields, and encompasses mainly the following areas : 1) Quantitative estimation of the damage already done to the natural surface drainage system. For this purpose damage to topography and drainage for the last fifty years have been made out through the aerial photographs and topographic map sheets 2) Analysis and comparison of different states of such photographs are carried through to indicate the extent of damage to the hydrological conditions inducing undesirable changes in its land-use pattern. Based on the analysis, concrete suggestions are made to restore the water drainage system which will be most suitable for future mining in the area containing high grade coal. The design and planning of the drainage system is based on the total system approach including the cost benefit analysis as well as hydrological considerations.

Jan 1, 1988

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By Douglas Robinson

This paper describes technical work done to develop a Spouted Bed Electrode Cell into a commercially viable Electrowinning Cell; (a previous paper has been presented at the ECS meeting in Paris in May of this year, with a more general overview of the cell, [1]). The studies have included hydrodynamic tests to understand the criteria for the circulating flow of metallic beads in the cell, particularly in the region at the entrance to the draft tube, and electrochemical tests to find a suitable diaphragm for extended time electrolysis. Various patent pending features were developed including a double nozzle to allow for automatic stopping and restarting of the bed, an arrowhead shaped draft tube to control the flow of beads into the entrance to the draft tube, a roof-top shaped device to control the flow of beads out of the top of the draft tube, an overflow weir to allow the continuous recovery of beads from the cell, and a family of diaphragm fabrics for extended operation. Prior to the identification of the diaphragm material, short circuits would develop within a few hours. A pilot scale cell was operated for three days, with continuous operator attention, and then for ten days with operator attention only on day shift. The cell is currently advancing to the next stage of development which will involve continuous testing in a commercial copper electrowinning facility.

Jan 1, 2003

By O. B. Hopkins

Activity in the oil industry in Peru during 1930 was confined almost entirely to the three old producing fields in the northern coastal area. In the eastern part of Peru, in the valleys of the Maranon, Ueayali and Huallaga rivers, additional geologic work was carried on, but no drilling was undertaken. The Peruvian Government granted a concession on June 27, 1930, to W. R. Davis and associates for the building of a railroad from the west coast at Bayovar to Yurimaguas on the Huallaga River. This concession contemplates the construction of 800 to 900 km. of railroad across the Andes and carries with it a grant to the concessionaire of 12,500,000 acres of land with oil and mineral rights. A similar concession was granted in 1926 but after several extensions was rescinded in July, 1929, on the grounds that the concessionaire had failed to begin work on the railroad within the time limits of the contract and its extensions. The production in barrels from the three coastal fields of Peru has been as follows: 1929 1930 International Petroleum Co.......................... 10,821,117 9,766,922 Lobitos Oilfields, Ltd................................ 2,508,091 2,613,511 Zorritos........................................... 75,000a 78,000a 13,404,208 12,459,060 a Estimated. No definite figures available. Although not large, the Peruvian production has been steady during the past years. The reduction of approximately 8 per cent. in 1930 as compared with 1929 is the result of the world's overproduction and the attempt on the part of the International to restrict the output to conform with the available market. International Petroleum Company International Petroleum Co. owns the oldest producing property in Peru. The first well was drilled there in 1872. The cumulative production from the property from 1900 to 1930 inclusive has been over 92,000,-000 bbl. from an area of 15,000 acres. The recovery per acre has varied

Jan 1, 1931

By Richard D. Call

In any open pit, some slope instability can be expected, varying from bench sloughing to large-scale slope movement. Major slope displacements are preceded by small, but measurable, displacements and by other indicators of instability, such as tension cracks, rock noise, and changes in groundwater levels. A comprehensive monitoring pro- gram, capable of measuring and assimilating displacement related data, is essential for sound pit operation. The objectives of a pit slope monitoring program are 1) to maintain safe operational procedures for the protection of personnel and equipment; 2) to provide advance notice of instability so that mine plans can be modified to minimize the impact of slope displacement; and 3) to provide geotechnical information for analyzing the slope failure mechanism, for designing appropriate remedial measures, and for conducting future re-design of the slope. Surface displacement measurement using conventional survey equipment and extensometers has been the most widely used method, and it is still the most cost-effective. Tiltmeters and borehole inclinometers are also useful tools, and there are promising developments in micro- seismic monitoring. A monitoring system should have redundancy in both type and number of measurements, and be capable of rapid and effective dissemination of displacement information to those affected.

Jan 1, 1983

By Rodrigo Jerez

The mining business in general, and coal mining in particular, is exposed to frequent and significant swings in the business cycle. Marginal coal production enters the market place in a nearly perfect competition. It must be priced aggressively if market share is to be gained. The minimum price acceptable from the standpoint of the producer is reached at the point where total variable cost are recovered. Competition occurs as companies move to reduce their variable costs in an effort to cover some portion of their fixed costs at reduced market prices. Production planning and scheduling plays a critical role in reducing costs. Multiple scenarios based on changing market conditions require that competing firms have tools available to evaluate the economic impact of transportation, blending, and processing options. In certain applications, significant cost savings can occur as a result of blending or altering preparation levels. Linear programming provides a tool with which to evaluate options and acts as a like between the mine plan and marketing decisions.

Jan 1, 1992

By Suresh K. Bhatt, Gary L. Mowrey, Timothy R. Rehak, David K. Ingram

Coal and nonmetal mining used about 4.3 billion pounds of explosives and blasting agents during 2001 in the United States. A major part of this consumption was related to surface mining. Mine Safety and Health Administration accident data indicate that flyrock and lack of blast area security were the primary causes of blasting-related injuries in surface mining. Fatal injuries due to lack of blast area security were primarily caused by failure to clear blast area or inadequate access control to the blast area. At a coal mine, a neighbor walked into the blast area and was fatally injured. The blaster could not see the victim entering the blast area from the firing station. In another case, a passenger in a vehicle was fatally injured by flyrock because highway traffic was not monitored during the blast. In another example, a dozer operator entered a blast area due to lack of access control. Several fatalities resulted from using inadequate or no blasting shelter. A crane operator was fatally injured while standing in the open about 120 ft from the blast site. In another instance, a helper, standing about 150 ft away from the edge of a blast, was fatally injured by flyrock. In a limestone mine an equipment operator was fatally injured while guarding access roads in a pickup truck. This paper briefly describes six representative fatalities due to flyrock and lack of blast area security in coal and nonmetal mines. Several mines were visited to collect information relative to working practices aimed at mitigating blasting hazards. Salient information obtained through these visits is presented.

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By Arthur Knapp

The law of supply and demand is, in general terms, that law which governs the price of any commodity in an unrestricted competitive market. There are several variables which, for the purpose of this discussion, will be defined only as they apply to the petroleum industry: Production: The volume of petroleum that is moved from leases. Stocks: The volume of petroleum that is in the hands of the tank farm and pipeline companies. Inventory: The value of the stocks at the market. Consumption: The indicated delivery of oil to others than those who hold stocks. Demand: The potential absorbing power of the consuming market. Demand is the expression of the needs of the consumer and may depend on the economic value of the oil to the consumer. In times of low prices, the demand is the same as the consumption but during periods of high prices or deficiency in supply, the demand may be greater than consumption. A general expression of the law is as follows: production or consumption Some relation between stocks and or controls price or demand inventory The Law as Applied to Crude-oil Market The above general expression of the law shows that there are six relations between variables that must be investigated in any attempt to establish the exact status of price control at any time. Production vs. Consumption If stocks of crude oil were very low, so that the flow of oil to the market was directly from the producer to the consumer and not, in a large measure, through stocks, some relation between production and consumption would be proportional to price changes. We have no criterion whereby we can tell, at present, what volume of stocks and production

Jan 1, 1924

On Wednesday evening, Jan. 27, 1915, were held in the auditorium of the Engineering Societies Building the inaugural exercises of The Engineering Foundation, established by the United Engineering Society. The initial gift to the Foundation of $200,000, made by Ambrose Swasey, Past President of the American Society of Mechanical Engineers, was formally accepted at this time. So far as known this is the first instance of a foundation devoted to engineering purposes. This meeting con-stituted also an appropriate tribute to the generous gift made to the Foundation and gave opportunity for expression of the satisfaction and approval which are felt by engineers everywhere at the establishment of a means of promoting the good of mankind through the work of the engineer along the broadest lines. Gano Dunn, President of the United Engineering Society and Past President of the American Institute of Electrical Engineers, acted as presiding officer, and on the platform were seated representatives of the three societies constituting the United Engineering Society, and of the American Society of Civil Engineers. Members of the four societies and many other friends interested in the profession composed the audience.

Jan 3, 1915

By S Latchireddi

Close circuiting autogenous and semi-autogenous mills is anenergy efficient way of grinding and a number of operations haveutilised this in the design of their comminution circuits. Owing tothe large flow of slurry through the mill that results fromoperating this way the grates and pulp lifters have to be designedto cope. However, the literature has little or no information onhow grate and pulp lifter size and design are related to theirability to remove slurry from the mill. Over the last few years theJKMRC has been researching this area and has developedrelationships between grate/pulp lifter design and flowratecapacity. At the same time it has determined the major causes ofpulp lifter inefficiency and a solution to preventing thisinefficiency (the Twin Chamber Pulp Lifter). This paperdescribes the models that have been developed through thisprogram and uses industrial scale data to illustrate their accuracy.Results from the industrial trials of the Twin Chamber PulpLifter are also presented.

Jan 1, 2001

By J. W. Gilbert

DuriNG the sinking of the Needmore shaft, on one of the leases of the Eagle-Picher Mining and Smelting Co north of Webb City, Missouri, a very strong flow of water was encountered at a depth of 140 ft. Because OF the speed at which the water rose in the shaft after pumping was discontinued, and in order to speed up sinking operations, a new type of shaft bar and drilling equiprnent was devised, which saved approximately one hour on each shift This bar is made of an ordinary scren type shaft bar with a common drill arm attached to the bar by clamps and welded Into place To this drill arm is attached an ordinary arm clamp with set collar below Through this clamp is attached another drill bar of ordinary length so constructed that it slides back and forth and rotates around the perimeter of the shaft on the set collar A tripod saddle with legs removed is welded to the rotating bar, which enables the drill operator to drill holes at any angle completely around the shaft and also, after an arm extension, permits the drilling of the corner holes without removal of the rig from the saddle Upon completion of the drilling of a shaft round, all that is necessary for the complete removal of the drill machine and shaft bar is to engage the hoist hook through a. ¾-in. eye provided for that purpose on top of the bar and disconnect the air and water lines from the machine, thereby making it possible to pull the whole apparatus out in one piece. At no time is it necessary to remove the machine from the saddle Screw jacks are installed on the vertical bar to further ensure the rigidity of the shaft and bar arm. The accompanying sketch illustrates the details and method of setting up.

Jan 1, 1946

By Walter S. Weeks

THE process of cooling air by allowing it to expand and do work in an engine is well known, but the theory of obtaining cold air by free expansion without the aid of an engine operating with cutoff has been little discussed. Case 1 If compressed air is allowed to expand to the atmospheric pressure through an orifice in an sir line that is supplied by a running compressor, no cooling results except the negligible one due to the Joule-Thompson effect, which will not be considered in this discussion. The effect of moisture will also be neglected. Symbols P1 Absolute pressure in pipe line, lb. per sq. ft. P3 Atmospheric pressure, lb. per sq. ft. V1 Volume occupied by 1 lb. air in pipe. V3 Volume occupied by 1 lb. air at P3. Cv Specific heat of air at constant volume, B.t.u. per lb. per deg. F. Cp Specific heat at constant pressure, B.t.u. per lb. per deg. F. T1 Absolute temperature of air in pipe, deg. F. T3 Absolute temperature of air outside after expansion and mixing and coming to rest. J Mechanical equivalent of heat (778 ft. lb.) R Gas constant for air, ft-lb. per deg. F. = 53.3. Formulas Consider 1 lb. of air moving out of a pipe. The air behind it does work on it to the extent of P1V1 ft-lb. This work is really done by the thrust of the piston of the compressor and does not come from any energy that exists in the air in the pipe. The pound of air contains

Jan 1, 1937

By Clarence Hicks

THE labor policy, of the Standard Oil Co. (New Jersey) is founded. first of all on paying at least the prevailing scale of wages in the community; on, the eight-hour day, with time and one-half for overtime; one day's rest in seven; sanitary and up-to-date working conditions; just treatment assured each employee; payment of accident benefits beyond the amount prescribed by the State compensation law; health supervision by a competent medical staff; payment of sickness benefits after one year's service; cooperation with employee in promoting thrift and better social and housing conditions; and assurance for a generous annuity at the age of 65, guaranteed for life after 20 years of service. Most of these features have been a part of the company's policy for many years, but it is only during the past two years that the cooperation of employees in determining these matters has been definitely assured through industrial representation. Industrial representation, in the Standard Oil Co., is a principle rather than a procedure. It is built upon the belief that personal association of those interested in any problem leads to a mutual understanding and a fair decision as to what is right. Fully believing in this, principle, representatives of employees and representatives of management evolved a simple plan, the basis of which is that it gives every individual employee representation at joint conferences on problems and fundamental principles affecting all those interested in the industry. It is based on cooperation, not antagonism; its operation makes perfectly clear both to management and to employees that their interests are identical, that mutual understanding and cooperation insure progress and success for all. Furthermore, experience has definitely shown that representatives of the employees are not only alert for the employees' interests but are as keen as the representatives of the management in determining and insisting upon fairness to the employer.

Jan 3, 1920

By Ian J. Duckworth, Pierre F. X. Mousset-Jones

A detailed heat flow project was conducted at the Homestake Mine in Lead, South Dakota. This paper presents results obtained from a stope sensor system installed in the mine. The design and installation of the system are described in detail in a previous paper (Duckworth et al., 1992). The major project objective was the construction of a comprehensive heat flow data base to allow the design and testing of a new climate prediction model applicable to irregularly shaped underground excavations in non-homogeneous surrounding rock types. A mechanized cut-and-fill (MCF) stope contributes a substantial overall heat source in a mine, and the effect of this source on the working environment must be considered when planning future ventilation and refrigeration requirements. The relative magnitudes of the component heat sources encountered with the MCF mining technique are presented, having been computed from actual stope beat flow data collected over a one-month study period. The percentage of the overall heat load that is removed from the scope for each component heat sink is evaluated, and the overall energy balance is analyzed. A one-month study length was considered a sufficient period of time to allow stope monitoring for a complete range of mining conditions.

Jan 1, 1993

The paper gives details of the performance of a 6-ft. by 6-ft. grate discharge ball mill which was converted into a rod mill of the overflow type and then into a grate discharge rod mill. Proposals for further alterations are outlined.INTRODUCTIONThe mill of King Island Scheelite (1947) Limited recovers scheelite by gravity methods.Crushed ore at the rate of 34 tons per hour is divided between two mills. (6 ft. by 6 ft. and 8 ft. by 6 ft. respectively), the mill discharges being pumped to a common distributor which feeds seven Hummer Screens. Each screen has three 4-ft. by 2-ft. Ton-cap sections and repulping compartments are provided. The screen oversize is returned to the mills whilst the screen undersize is finished grinding section product. A third (6 ft. by 6 ft.) mill regrinding the coarser table tailings also discharges into the common Hummer Screen Distributor.The screen undersize is pumped to a bowl classifier which separates at 200 mesh. The bowl classifier sands are treated on tables whilst the bowl classifier overflow, after thickening, is treated in the slime plant by flotation. The flotation concentrate is further concentrated on vanners and slime tables.A recovery of 80 per cent. is possible by tabling whereas only 50 per cent can be recovered in the slime section. The object of comminution is, therefore, to reduce all the new feed to less than a certain mesh (22 mesh Tyler) with the production of a minimum quantity of minus 200 mesh material. cheelite is, a very friable heavy mineral (Sp.Gr. 6'0) and is therefore susceptible to overgrinding. For the evaluation of grinding performance it is hence advisable...

Jan 1, 1955

By Tim Suljada, Mary Stewart, Jim G. Petrie, Damien Giurco

"The minerals industry is being challenged to reduce the amount of virgin ore that is mined, and to replace this material through the recycling of used commodity items and scrap, or by the reprocessing of waste materials. It is argued here that the existing technology base of minerals processing and refining offers real potential for handling these secondary resources. The challenge is to develop tools by which the most preferable recycling routes (both economically and environmentally) can be identified from a list of feasible alternatives, taking into account any operational constraints of these technologies.This paper describes an heuristic approach to developing the family of all technically feasible flowsheets to address this challenge, from which a preferred option may be selected according to a set of decision criteria (economic and environmental). Our approach uses conventional flowsheeting techniques of selecting flow variables and splitter functions, supported by design performance information for each unit operation. This set of design decision variables is augmented by knowledge of the suitability of a particular waste or scrap stream for a given unit operation within a flowsheet. We achieve this by comparing the composition of the scrap stream with the range of mineral streams for which the unit operation was designed initially. This is inspired by the “overlap” approach proposed by Legarth, where an “overlap” of 1 would suggest that there is high degree of compatibility between a given secondary resource stream and a primary mineral stream as inputs to a specific technology. The “overlap” concept has been extended to include information about the physical characteristics of secondary resource streams, as well as information relating to synergistic / antagonistic influences of minor elements present in the waste stream. A flowsheet which delivers a product of acceptable quality from a given secondary resource material is built up from a progression of unit technologies. The exercise is repeated to generate the family of all feasible flowsheets from combinations of acceptable unit technologies."

Jan 1, 2003

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.