Search Documents

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Desiree Willis

At 6 percent downgrade to a low point beneath California?s Sacramento River, the Lower Northwest Interceptor Sewer was a difficult project from the outset. Project owner Sacramento County Regional Sanitation District (SRC-SD) planned to excavate the V-shaped tunnel in two sections using an earth pressure balance (EPB) machine in soft ground. Muck removal, due to the steep downgrade, was a tricky proposition. ?We did look at muck cars, but determined they were not the best option due to the relatively steep slope of the tunnel alignment. The safety benefits of conveyors on this job were obvious, as there were not the potential hazards associated with muck cars traveling on an incline or derailing,? said Steve Norris, senior civil engineer for SRCSD The successful project represented one of the first instances of a conveyor system being used for a soft ground tunnel boring machine (TBM) application. Several projects in California, including a recent tunnel completed in 2009, have highlighted a growing acceptance of conveyor muck removal in a variety of ground conditions. Conveyors offer higher system availability than more common methods, such as muck cars, as they allow for continual operation of the TBM. The design of conveyor systems must, however, take into account the differences in material between soft ground and hard rock, including belt cleaning features, sealed transfer points and other elements.

Jun 1, 2010

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By P Gilroy

In recent technical investigations that were triggered from ore for rail shortfalls at Yandi, BHP Iron ore has identified a gap in resource knowledge relating to geo-metallurgical characteristics that predict materials handling performance and throughput. Within these investigations BHP has learnt that this lack of resource knowledge has translated to a lack of predictability associated with mine planning inputs which has resulted in poor compliance to plan and deviation management practices. A business value chain was developed in an attempt to identify the best possible solution to unlock this resource knowledge in the short, medium and long term planning horizons. A fast fail approach was taken with the implementation of hyperspectral blasthole analysis, which was chosen to deliver the best possible value driver for the asset. This report will detail the Yandi journey in expanding the hyperspectral and geo-metallurgical value chain, unlocking resource knowledge along the way. CITATION: Gilroy, P, 2018. Development of an empirical geo-metallurgical model that unlocks value of the mineral resources at Yandi Mine, in Proceedings Complex Orebodies Conference 2018, pp 85–87 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By E. McCullough, D. Preece, M. Ortel

The mining and oil industries employ techniques such as geologic mapping, core drilling and electromagnetic field techniques to explore for new deposits. New discoveries of major near-surface ore bodies are becoming progressively rare and traditional exploration methods are unable to resolve ore bodies deeper than about 500 m (1640.4 ft). Consequently high-resolution seismic reflection techniques show great potential for exploration to much greater depths down to almost 3 km (1.9 mi).

Jan 1, 2013

By Herle Rodríguez, Frank Astete

El modelo de “liderazgo por octógonos”, nace de la necesidad de generar una estrategia para visibilizar el liderazgo permanente en terreno de los líderes (caminatas gerenciales) y conocer el nivel de cumplimiento de los indicadores de seguridad y salud en cada una de las áreas. El ícono de los octógonos, tomo de referencia a los utilizados por el Ministerio de salud para identificar el riesgo a la salud de un producto, de la misma forma los octógonos (verde, amarillo y rojo) indican el nivel de cumplimiento e implementación del programa de seguridad y salud en cada una de las áreas. Esto logra un impacto visual por la relación al riesgo y la importancia en el cuidado de las personas.

Sep 29, 2023

By V. O. Tenorio, D. Tolmachoff, K. Willa Brown, K. J. Kingsbury, J. B. Nickels, G. J. Nail

A major design feature to consider from the initial pioneering works until reaching full mine production of icy regolith at the South Pole of Moon will be the ramp. This will allow the access of equipment and personnel in and out of the excavation area. Although most of the requirements considered when designing a ramp on the Earth are similar, the fact of working in low gravity, with zero atmosphere, the potential exposure to high radiation, extreme temperature levels and drastic changes of illumination, from intense light to total darkness, are new factors to be included. Transversal sections are obtained according to the progression sequence of the production levels, with changes in length, gradient, friction factor of the terrain and curvature when required by the location characteristics and the specification of the equipment utilized. A MATLAB script was developed to calculate all the variables, in order to obtain 3D generated surfaces from the range of possible profiles.

Mar 2, 2022

By Chengyi Ding, Xuewei Lv, Senwei Xuan, Chenguang Bai, Kai Tang, Gang Li, Yang Xu

Perovskite easily forms during sintering of vanadium titanium magnetite (VTM) and is unfavorable for the following blast furnace. Steelmaking can concomitantly produce a great quantity of oxidized scale composed mainly of FeO and Fe3O4. Calcium ferrite (CaOFe2O3, CF) can be formed by oxidized scale with lime in air atmosphere and then added to the VTM during sintering. X-ray diffraction (XRD) results indicated that perovskite is not generated at low temperature but only when the temperature increases to 1473 K in the CF–TiO2 system. Therefore, VTM sintering can be performed with a low-temperature process with doping of CF. Perovskite formation is mainly divided into two steps. First, CF melts and produces CaO. TiO2 and CaO then combine to produce perovskite. This paper also discussed the reaction mechanism of CaO–Fe2O3–TiO2 ternary system to compare the generation routes of perovskite.

Mar 1, 2018

By Neale R. Neelameggham, Brian R. Davis

Organic agriculture is using natural materials such as degrading plant matter to replenish soils. This includes use of naturally degraded plant components such as peat, humus and weathered brown coals. Another important natural organic matter which has not been applied in agriculture thus far has been the black coal, Here we show that reversing the coal formation reaction by combined hydro-oxidation principles of biochemical engineering in natural conversion methods in an accelerated fashion. The modified coal soil additive can convert arid lands into farm lands for the future to sustain the population growth. In addition, the development of this new use of black coal will revive economically deprived areas from phasing out coal in the USA and Europe. This will show how the Stored energy in coal can be made renewable in helping plant growth under the soil to facilitate above ground photosynthesis.

Mar 1, 2018

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By Ian M. Loomis, Keith G. Wallace

The Waste Isolation Pilot Plant (WIPP) is a U.S. Department of Energy research and development facility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste. The waste storage horizon is 655 m (2150 ft) below surface in bedded salt. To date the WIPP project has not emplaced any waste. There are three intake shafts used to supply air to the underground. All air is exhausted though a single return shaft. The total design airflow during normal operations is 200 m3/s (424,000 cfm). The ventilation system is designed to provide separate air splits to construction, experimental, and storage activities. Separation is achieved by isolating the storage circuit from the construction or experimental circuits with bulkheads. Any air leakage must be towards the storage area of the facility. Field studies have shown that the pressure differential necessary to maintain the correct leakage direction is susceptible to the effects of natural ventilation; therefore, extensive studies and analyses have been conducted to quantity the natural ventilation effects on the WIPP underground airflow system. A component of this work is a monitoring system designed to measure the air properties necessary for calculation of the natural ventilation pressure (NVP). This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure at strategic locations on surface and underground. The psychrometric parameters of the air are measured every fifteen minutes. From these data, trends can be determined showing the impact of NVP on the ventilation system during diurnal variations in surface climate. Both summer and winter conditions have been studied. To the author's knowledge this is the first reported instance of automatic and continuous production of time and temperature variant NVPs. This paper describes the results of the initial monitoring study. INTRODUCTION The ventilation system at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico, is designed to perform two distinct functions. First, it supports normal mine ventilation requirements complying with all state and federal mine regulations. Second, the system is designed to prevent an uncontrolled release of radioactive contaminants from the storage and transportation areas of the facility. Although a nuclear radiation release in the facility is considered unlikely, many special features are implemented in the ventilation system to prevent the possible spread of contamination. The facility is constructed with the waste transportation and storage areas separated from the mining and non-radioactive experimental areas. The ventilation system is designed such that air leakage is from the mining and experimental areas to the storage areas. Furthermore, radiation detectors are located throughout the storage and waste transportation areas underground and an exhaust filtration building is installed on surface to prevent the possible release of radiation to the environment. For over two years the underground ventilation system has been rigorously tested and balanced. It was during this period that the adverse effects of NVP were noticed and subsequently quantified. From extensive field studies and computer models, several mitigating features were designed and constructed and special operational procedures were implemented to control the impacts of NVP. To quantify more accurately the NVP at the WIPP, a continuous monitoring system was installed. This monitoring system consists of measuring dry bulb temperature, relative humidity, and barometric pressure every fifteen minutes at strategic locations on surface and underground. From this psychrometric data, the NVP is calculated. Fan operating pressures and flows and strategic differential pressures are recorded from the site Continuous Monitoring System (CMS). The monitoring system provides a means of evaluating how the ventilation system behaves in regard to climatic conditions and to judge the efficacy of the mitigating features and operational procedures. To the author's knowledge, continuous calculation of NVP as a function of time and surface temperature has not been previously reported. Overview of the Waste Isolation Pilot Plant The U.S. Department of Energy determined that the plastic nature of bedded salt may provide the best solution to isolate transuranic (TRU) waste from the biosphere. Initial evaluations at the WIPP site began in 1974. In 1979, the United States Congress enacted Public Law 96-164 for the construction and development of the WIPP project. The mission of the WIPP is to demonstrate the safe, long-term disposal of TRU waste generated by the national defense programs of the United States. TRU waste is classified as a low to medium level waste. The waste is stored in drums and does not produce significant heat (not greater than 1 W per drum). The WIPP site is located approximately 47 km (29 miles) east of Carlsbad, New Mexico in the Chihuahuan Desert. The repository is located in the 630 m (2000 ft) thick Salado Formation. This Permian Basin salt deposit is about 225 million years old and appears to have been minimally disturbed by earthquake, faulting, and ground water activity since it was deposited. The underground facility is 660 m

Jan 1, 1993

By M. B. Bever, A. B. Michael

The solidification of aluminum-rich aluminum-copper alloys was investigated for different solidification rates. The measured amounts of nonequilibrium eutectic were compared with the amounts calculated on the assumption of no diffusion in the solid. The morphology of the eutectic was studied and dendritic spacings were measured. Compositions of the cored primary solid solutions were determined by quantitative autoradiography after activation of the solute copper by neutron irradiation. CONSIDERABLE progress has been made in recent years toward an understanding of the solidification of metals. This is especially true for the factors involved in nucleation, the controlled growth of metal crystals from melts, and various aspects of the freezing of ingots and castings. Many features of the solidification process, however, are not understood adequately and much further work is required. In the research reported here the solidification of a series of aluminum-rich aluminum-copper alloys was investigated. Different degrees of deviation from the idealized case of equilibrium solidification were attained by varying the rate of solidification. Thermal analysis and microscopic examination were supplemented by lineal analysis and autoradiography. The latter required the use of radioactive tracers and was adapted to the quantitative determination on a microscale of concentrations of copper dissolved in aluminum. The tracers were produced in situ by activating the copper with neutrons. These techniques permitted a correlated interpretation of the temperature-time history, the amounts of nonequilibrium eutectic and the general morphology of the alloys, and yielded quantitative data on microsegregation. Nonequilibrium Solidification In the general case of the solidification of a solid solution in accordance with the phase diagram, the composition of the coexisting liquid and solid must change continuously. This change requires diffusion, which at best remains incomplete in the solid during solidification. The resulting inhomogeneity of the solid solution crystals is well-known as coring, dendritic segregation, or microsegregation. The generally accepted analysis of coring assumes that, 1—no diffusion occurs in the solid, 2—diffusion is complete in the liquid, and 3—the composition of the solid formed on cooling through any infinitesimal temperature interval is given by the solidus of the phase diagram. On this basis, In this equation m designates mass, x designates the concentration of solute and the subscripts L and S refer to the liquid and solid phases, respectively; the subscript o indicates the initial state, in which the liquid is identical with the entire system. Eq. 1 or its equivalent has been derived repeatedly'-7 and an analogous equation, known as Rayleigh's equation, has been used for distillation. The assumptions on which Eq. 1 is based do not include an infinitely fast cooling rate as sometimes stated. In fact, Olsen and Hultgren %ave shown by experiment that very high solidification rates suppress coring, presumably by preventing diffusion in the liquid and by the effect undercooling has on the composition of the nucleus. Coring thus occurs at rates of cooling which are too fast for a close approach to equilibrium in the solid and too slow to suppress diffusion in the liquid and to cause marked undercooling. If the liquidus and solidus approximate straight lines, Eq. 1 simplifies to The fraction of liquid present at any temperature during nonequilibrium solidification can be calculated from Eqs. 1 or 2. By the lever relation it is

Jan 1, 1955

By Z. Ren, M. Tomlinson, E. Asselin

"Organic carbon blinding is a common, yet often partial, solution to the reduction of preg-robbing. A quantitative method to assess the extent of adsorption of a given blinding agent is presented herein. The adsorption of several blinding reagents on various carbon samples is quantified using electrochemical impedance spectroscopy (EIS). EIS results showed that kerosene is more strongly adsorbed on carbon than sodium lauryl sulphate (SLS), while SLS can hinder the charge transfer process of the oxygen reduction reaction on the carbon surface more effectively. The effectiveness of SLS is pronounced when its concentration is higher than 100 ppm. Raman spectra are presented for selected carbon samples: as the area ratio of the disordered peak to the graphitic peak increases, blinding agent adsorption increases.INTRODUCTION The presence of naturally occurring constituents in gold ores may adversely affect the extraction of gold in cyanide leaching since the gold cyanide complex, Au(CN)2–, can be adsorbed by these constituents (M. Adams & Fleming, 1989; Afenya, 1991; Miller, Wan, & Díaz, 2005). Such ores are known as “preg-robbing”. Preg-robbing behavior may arise from natural carbonaceous materials in the ore (M. Adams & Burger, 1998). In the past decades, a number of pre-treating methods have been developed for refractory carbonaceous ores (Arriagada & Osseo-Asare, 1984; Beer, 1994; Dunne et al., 2007; Jiang, Liu, Xiao, & Yang, 2012; Kohr, 1997; Kulpa & Brierley, 1993; Menne, 1992; Menne & Revy, 1994; Moyes & Houllis, 2010; Petrie, Craw, & Ryan, 2005; Simmons, 1996). The method known as blinding is one of the most effective and economical pre-treatment methods (M. D. Adams & Burger, 1998; Albert, 1923; Darrow, 1924; McQuiston & Shoemaker, 1975; Van den Berg, 2000). Blinding, also referred to as blanking or passivation, uses a chemical reagent to passivate the preg-robbing carbon by selective absorption or wetting (Bas, Altinkaya, Yazici, & Deveci, 2012; Brierley & Kulpa Jr, 1993; Dunne et al., 2012; Van den Berg, 2000; Yang, Qian, Song, & Dong, 2013; Yen, Amankwah, & Choi, 2008; Zhou, Jiang, & Choi, 2014). Organic reagents, which selectively adsorb on the surfaces of activated carbon and “smother” the surface, have been used for blinding carbonaceous matter in gold ores prior to cyanidation. Two comprehensive studies by Abotsi and Osseo-Asare and Adams and Burger have been published on this topic (Abotsi & Osseo-Asare, 1986; M. D. Adams & Burger, 1998)."

Jan 1, 2017

By M McCarthy

Over the last six years Mandalay Resources has increased production rates and improved safety outcomes at its Costerfield mine in Victoria, Australia. This mine is an underground operation utilising narrow mining techniques to extract vertical veins, and produces up to 80 000 equivalent ounces of gold per annum, in both gold and antimony value.The operational challenges of narrow vein mining include controlling overbreak when veins being mined are only 300 mm wide. The mine has developed methods and modified equipment to suit extraction of these veins. Productivity improvements over the period have involved development of a stoping method and equipment to suit 1.8 m wide development drives. Over the last five years and during a skills shortage, recruitment, training and retention of personnel has been key to keeping corporate knowledge and skills to execute a careful efficient mining technique to minimise overbreak.Managing an underground operation close to nearby residents has unique challenges. Historically Victorian residents had family members work as underground miners; however, in the current day with few underground operations in this jurisdiction, community knowledge of mining has decreased. The Costerfield Operations are only 100 m from the nearest residence and the company values community engagement, partnership and investment with local Heathcote organisations.The mine has invested substantially in executive coaching of its leadership team early, which has paid dividends in problem solving potential of that team and ensuring the operation delivers on its promises to all stakeholders. The operation has become safer and employees are now more aware of their individual contribution in producing safe, efficient gold and antimony that benefit the whole operation, community and the region.CITATION:McCarthy, M, 2016. Costerfield – a narrow vein case study, in Proceedings International Mine Management Conference, pp 331-338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By M. Visnjic

Open Pit Mine Production scheduling under commodity price uncertainty suffers from an exponentially increasing problem size as simulations and real options flexibility are used to generate and evaluate multiple production schedules. Robustness evaluation techniques attempt to evaluate a production schedule that is generated on a single set of economic parameters against several varying prices and sources of uncertainty. This approach is invalid as the corresponding optimal LOM mine plan will change for each set of evaluation parameters. Using commodity market futures and treasury bonds as production schedule economic input parameters provides fully price and time-value-of-money risked scheduling parameters that maintain a deterministic problem size. This paper will provide comparative analysis of project NPV’s coming from traditional price uncertainty evaluation based on a single fixed LOM mine plan using varying prices versus evaluation based on varying LOM plans that are both generated and evaluated using varying prices. When cross evaluating constant price mine plans against simulations, the upside potential and downside risk of a project are significantly misrepresented. INTRODUCTION The life of mine (LOM) production scheduling problem seeks to answer the question of from where and when to extract a given block within the ultimate pit limit as well as where and when to process it. Solving this problem takes into account the constraints of extracting any particular block while seeking to maximize the net present value (NPV) of the mineral asset as a whole. A direct driver of the value of a block, and there for the entire asset, is the market price of the commodity in question. Complications arise when an optimal production schedule is attempted to be solved under price uncertainty. Many solution methodologies have been proposed in an attempt to optimize under this criterion, yet there are three salient aspects that are overlooked during this process. They are: • Generating a single production schedule and evaluating it against many simulated price paths. • Failing to understand the mechanism describing particular commodity price behavior • Inappropriate risk adjustment In an effort to address these aspects of production scheduling under commodity price uncertainty, we propose a methodology to define the economic parameters as input that is applicable to most if not all production scheduling approaches. This methodology will not only simplify the production scheduling process in terms of establishing block value but utilizes the risk adjustment of real options valuation to avoid the arbitrary blanket risk adjustment of traditional discounted cash flow valuation. Our findings conclude that attempting to optimize around individual price paths is futile and using a market risk adjusted single price forecast provides a justified economic basis for production scheduling while maintaining the same problem size as a deterministic production scheduling problem.

Jan 1, 2019

By C Rizos, A Ng

Land surface deformation can be caused by underground mining activities. The maximum subsidence normally occurs directly above the location of the excavation of the coal seam. In the case where the longwall mining technique is applied, the magnitude and shape of the subsidence bowl are constrained by the longwall structure (pillar). This paper describes the use of satellite radar interferometry for monitoring surface subsidence due to underground mining, as a cost-effective geodetic technique and complementary to conventional ground surveying techniques. This paper uses data acquired by the current generation of SAR satellites û the European ENVISAT and the Japanese ALOS û to monitor ground subsidence in the southern highland coalfield in New South Wales, Australia. An accumulated DInSAR subsidence mine map is produced using six successive ALOS acquisitions. The results are post-analysed with the aid of geographic information systems (GIS) and validated using ground survey data.

Jan 1, 2008

By Paul W. Cleary

"DEM application in mineral processing has for many years been heavily focused on simulating mills of various types. This method can be used to simulate many other aspects of mineral processing operations and can be used both to enhance understanding of the underlying flows and of issues such a breakage, wear, blockage, product degradation, segregation and mixing. The application of DEM to four important classes of non-comminution problems and equipment commonly found in or near mineral processing plants are described. These are:- Particle transport (examples include a conveyor belt and an inclined screw conveyor)- Sampling (assessment of sample bias for cross-stream samplers)- Separation (the efficiency of vibrating screens)- Storage and reclaim (discharge from a multi-port hopper and segregation in a splitter bin with asymmetric ingoing and outgoing conveyor belts, apron feeders and impact plate)."

Jan 1, 2003