Search Documents

By C. M. Young

THIS is an attempt to bring together some of the knowledge of the .coal-forming conditions obtaining during the Pennsylvanian period in the Western Interior Coal Province, to sketch briefly the present extent and character of the coals produced, and to show the beginning of cor-relation of beds over wide areas. Coals of later age than the Pennsyl-vanian are not included and, for reasons that will appear later, little attempt is made to cover the districts of eastern Oklahoma and western Arkansas, and northern Texas is omitted entirely. GEOLOGICAL CONDITIONS The conditions that made possible the formation of large coal beds in the United States were most favorable in the Pennsylvanian period, formerly known as the Upper Carboniferous. The geological conditions can be determined from the records, but not the reasons for them. Preceding the Pennsylvanian was the Mississippian, formerly known as the lower Carboniferous and still later as the sub-Carboniferous. Dur-ing this time, large bodies of limestone were deposited and at the close f the Mississippian they were warped upward and for along period were eroded. Then there began a period of subsidence, more or less inter-rupted at times, during which the Pennsylvanian strata were deposited (see table on page 2). " These consist of sandstones, limestones and shales, with occasional coal beds: At the beginning of the Pennsylvanian there was subsidence, which allowed the sea to extend over the eroded Mississippian surface to the north and east, extending over eastern and central Texas, a large part of Oklahoma, with a projection into Arkansas, over Kansas and part of Nebraska, all the northern and western part of Missouri, a large part of Iowa except a strip in the north, most of Illinois, practically all of Ken-tucky, northern Tennessee, most of Indiana, all of the eastern part of Ohio, practically all of West Virginia, western Maryland, the west end of Virginia, and a large part of Pennsylvania. The Ozarks were already

Jan 1, 1935

By Worotnicki G, Tillmann V. H

Past experience with fully bonded cable dowels placed as a means of reinforcement in highly stressed crop pillars at the New Broken Hill Consolidated Limited (NBHC) mine indicated such support was not fully effective. Typically overbreak of the crown occurred leaving long lengths of cables hanging from the back stripped of grout and rock with the potential load carrying capacity of the cables not having been fully utilised. This mode of behaviour had been observed in the cable dowelled crowns of three longhole open stopes (EROS) mined to the No. 12 level at NBHC. A system of support with improved mechanism of load transfer from rock to cable and capable of full utilisation of cable strength was proposed for the crown pillars of future Stopes.

Jan 1, 1983

By Donald O. Rausch, Robert H. Merrill

12.1 -1. Introduction. Problems concerning slopes in soils and rock generally arise in connection with road cuts and open pit mines. The angle at which a slope will safely stand is of major economic importance to both the road designer and the open pit operator. Stable slopes in soils and rock are evaluated through two fundamental approaches, namely, soil mechanics and rock mechanics. The approach selected to make this evaluation depends upon the material in the slope. For the purposes of this chapter, only slopes totally in soil or totally in rock are considered. By definition, soils are unconsolidated accumulations of solid materials produced by mechanical and chemical disintegration of rocks or the accumulation of sediments (28); rock is defined as the hard, compact, natural materials composing the crust of the earth (10). The basic factors affecting slopes in soil or rock are similar, although rock strengths are orders of magnitude greater than soil strengths. In general, the strength of large masses of soil depends upon the texture of the soil, the particle size, cohesion, and resistance to tensile and shear stress; the strength of large masses of rock depends upon the strength of the rock and the defects, such as faults, fractures or joints, that intersect the rock. Further, some of the defects in rock are cemented or uncemented, and may be filled with materials that are strong or weak compared to the rock. In slopes of either soils or rock, the stability is presumed to be a function of the slope height, slope angle, the size of the excavation, and the stresses imposed on the soil or rock by tectonic and/or gravity forces, earthquakes, or other static or dynamic forces. In addition, both soil and rock slopes are affected by static and dynamic water pressures in the pores of soils or permeable rocks or in the defects in the rock behind the slope. Visual observations of slope failures also indicate that both soil and rock can deteriorate with time, and this deterioration may be caused primarily by weathering (27).

Jan 1, 1968

By Charles M. Means

A thoroughly modern coal-handling system has been installed at the Pittsburgh Terminal H. H. &. Coal Co.'s new No. 8 shaft, or Cover-dale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur of the Montour R. R. The Pittsburgh scam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with thcir remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. Mine Substation The transformer substation is adjacent to a. pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies. Main Switchboard The 2300-volt circuit is carried underground in a conduit from the transformer substation to an oil switch in the substation and supply hoist building. This is the main switch controlling the 2300-volt busbars mounted back to a twelve-panel black-slate switchboard. From the switchboard, 2300-volt circuits are carried to transformers feeding the street and house lighting systems and to other transformers furnishing power for the elevator and lighting circuits in the store building. Other 2300-volt circuits run from this switchboard to the main hoist building, fan house and auxiliary or man-and-supply hoist. High-tension wiring,

Jan 1, 1922

By R Austerberry, S Green

Highly weathered ground, limited collar options and the need to achieve a desired outcome at the lowest possible cost led to the need to adopt a construction approach that had no established design methodology. The newest ventilation shaft at Mandalay Resources’ Costerfield Operations had to be established to a depth of 30 m through poor ground best described as ‘sticky swelling clay’, some of which was contained within an old backfilled pit.The ability to excavate a traditional presink was not possible due to limited space and the introduction of men into the shaft was to be avoided due to the associated safety risks and corresponding increase in cost. Piling in conjunction with raise boring and remote fibrecrete application was identified as a possible solution that could achieve the desired outcome at an acceptable level of risk.Construction of the piles was challenging and required continual refinement until an acceptable level of productivity could be achieved. Limitations on concrete delivery was taken into consideration to ensure hole stand-up time was acceptable and re-drills were not required. The adoption of a set process from alignment, drilling, concrete placement and testing ensured the desired design was achieved. Mine operators should consider the use of piling as a method of shaft stabilisation for the portion of raise bored shaft that passes through the weathered zone.The importance of quality control and attention to detail through the entire shaft construction process cannot be underestimated as issues such as insufficient geotechnical investigation, pile and pilot hole deviation, concrete and fibrecrete quality, as well as delays in the application of fibrecrete can place the success of the project at risk.This paper outlines key learnings from a client’s perspective with regards to the concept, planning, design, execution and completion of a 3.1 m diameter raise bore shaft through both weathered and highly structured ground at the Augusta Mine.CITATION:Green, S and Austerberry, R, 2014. Piling and raise bore construction – key learnings from a client’s perspective, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

In 1969, Queensland Mines Limited obtained two large Prospecting Authorities in Arnhem Land, Northern Territory, Australia. The Nabarlek uranium deposit containing some 12 000 t of U308 was discovered on one of these in June 1970. Mining and stockpiling of this deposit were completed in 1979 and processing to yellowcake, which commenced in June 1980, is expected to occupy an 8-10 year period. The continuation of exploration, essential for the company to become a longer- term producer, was inhibited in 1972 by a Federal Government "freeze" on exploration in Aboriginal Reserves in the Northern Territory. Subsequently, the procedure for explorers to gain access to exploration areas in Aboriginal land was radically changed by the proclamation of the Aboriginal Land Rights (Northern Territory) Act 1976. As a result of this Act and the associated administrative policies adopted by Governments, Queensland Mines Limited has not yet regained access to the exploration areas it formally held in the early 1970's.

Jan 1, 1986

By Camila Peres Massola

Este trabalho avaliou o efeito da corrosão no desgaste de bolas de aço e de ferro fundido branco de alto cromo durante a moagem de minério de ferro, através de ensaios eletroquímicos e de desgaste em moinho de laboratório. Foi feita uma alteração no modo tradicional de realização do ensaio de polarização potenciodinâmica, utilizando polpa de minério de ferro a 70% de sólidos (em peso) no eletrólito. As curvas de polarização obtidas foram compatíveis com os resultados de desgaste, de modo que as curvas correspondentes aos metais na condição mais ativa estavam associadas às menores taxas de desgaste nos ensaios de moagem em laboratório, demonstrando que os ensaios de polarização realizados podem ser utilizados como indicativo do comportamento do metal na moagem de minério de ferro. Verificou-se que, nas condições avaliadas, o efeito da corrosão não foi significativo no desgaste dos corpos moedores, tanto de aço quanto de FFBAC.

Aug 16, 2017

By M Hood, X S. L, W J. T Daniel, H Gurgenci

It is believed that disc cutter shape affects rock fracture and therefore cutter performance and cutter life. However, the current generation of disc cutters is made of hardened steel and these cutters wear rapidly and consequently they are unable to maintain their original shape in strong and abrasive rock. This wear problem could be reduced if the cutter was made from a harder material. Unfortunately as material hardness increases so does the propensity for brittle failure. In this study the optimum cutter shapes were identified by studying the mechanics of rock/tool interaction. The results showed that bevel and wedge cutters are better than cutters with dome and flat edges. A new cutter was designed, based on this result, using a harder material to increase the life by a factor of 20.

Jan 1, 1998

By M. Lak, M. Asghari, M. Saghaeian, R. Hejazi, A. Haratian

"Magnetic separation techniques are used extensively in mineral processing operations. Magnetic separators are robust and relatively easy to operate. As the ore get hard and low grade, fine grinding must be required mostly to allow for a high degree of mineral liberation. These processes encounter the magnetic separation process difficulty due to a significant change in the separation behavior of particles. This study investigates the effectiveness of a novel proven wet magnetic separator for the beneficiation of Lebedinsky (Russia) iron ore achieved through developing pole arrangement and tank design. Basis on the results of multiphasic simulation of a medium intensity magnetic separator (MIMS) and dense media tank using Magnetic Design Software, a new model of the MIMS separator was developed. The main of the new MIMS separator was focused on improving separation and the decreasing the number of separators in cobber stage of the plant. The new MIMS separator was tested into a pilot plant on the received samples from Lebedinsky iron ore plant. In addition to the basis on the results of the modeling, promising results of test work and previous experiences, it was claimed the unit capacity of new separator is 33.33% more than the existing separator that could decrease the number of separators. In addition, the significant energy saving in the same operational condition could be obtained without any important adverse effect on the final concentrate quality.INTRODUCTION Magnetic separation is a long-established method for the purification and removal of substances from fluids (Augusto et al., 1999; Buck et al., 2015; Hoffmann et al., 2002; Lauda et al., 2016; Lindner et al., 2010; Podoynitsyn et al., 2016; Rashidi et al., 2016), mainly in mining processing industries ranging from steel production to coal desulfurization as commercial technology (Andres, 1994; Augusto, 2002; Svoboda, 1987). High gradient magnetic separation as an effective method for recovering of weak and fine magnetic particles separation has undergone dramatic developments, and has also achieved extensive application during this time (Svoboda and Jujita, 1987). Magnetic separation operations can be categorized into high intensity as electrical (up to 20,000 gauss), Medium intensity (2000-5000 gauss) and low intensity (less than 2000 gauss) techniques. Magnetic separators offer a simple, clean and economic way to sort magnetizable ores and minerals. After pulverization, the material is run through an inhomogeneous magnetic field, where particles of different susceptibility experience different magnetic forces. The force increases with susceptibility, magnetic field and field gradient (Jongst et al., 1984).In magnetic separation, the difference in the susceptibilities of the various particulate materials is used to separate the material flow into two or more products (Wasmuth and Unkelbach, 1991). The magnetic force acting on a particle can be calculated using the following equation:"

Jan 1, 2018

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By Helênio Resende Silva Júnior

Arcelor Mittal Asturias coking plant at Gijon works, Spain, is undergoing a complete modernization of the whole coke making complex. In this context, Gijon has to be considered a brownfield project, where Paul Wurth has been awarded with the engineering, supply of key equipment as well as erection and commissioning supervision services for the rebuild of two coke oven batteries the modernization of the adjacent by-product and relevant waste water treatment plants. Main objective of this paper is to present the technological improvements introduced by Paul Wurth in the rebuild of a modern plant focusing on fulfilling all the recent environmental regulations.

Oct 30, 2017

By Sejong Kim, Younghoon Moon, Youngseon Lee, Eunyoo Yoon, Yonghyun Song

"Mg alloy has a high specific strength, however, their thickness reduction was limited on most parts because of their poor stiffness. Since the modulus of rigidity is an intrinsic property, improvement of modulus of rigidity to the enhancement of stiffness is impossible. Therefore, the modification of shape and structure is available method to enhance the stiffness of real part fabricated by Mg alloy sheet. There are many thin walled parts which are located in outer section of electromagnetic system.Poor stiffness is often shown on wide surface area part with steel sheet, which has also high modulus of rigidity. In these cases, various groove patterns are used to increase the stiffness of part. However, some different methods have to be used when general groove pattern can’t be used. So, we would like to propose some new method to high stiffness on thin walled precision forging of Al or Mg alloys.An effect of proposed method on stiffness enhancement can be confirmed by fabrication of prototypes as well as structure and forming analysis based on FEM."

Jan 1, 2015

By Stephen Chung

The quality of a blast design can be evaluated in many ways. It may involve fragmentation, muck profile, environmental effects in terms of vibration and the excavation of the blasted material. To assist and ensure an achievable cost effective design, numerical modeling techniques are often applied as part of the operating procedure. While excavation is one of the mining operations which has a direct influence on the bottom line cost of productivity, the characteristics of a pile of blasted material deserves a closer look in terms of diggability. This paper reviews the current diggability techniques available for application to the blasting operation. To help better understand the involvement in digging, this paper also introduces an evaluation approach based on a discrete element method. The model presented in this paper deals with many variables that are considered to directly affect digging. They are the density and cohesion of material, fragment shape and size distribution as well as the swell of a muck pile. To help visualize the analysis approach, sample runs and animations are given in the paper to show the setup of muck piles produced in bench blasting as well as in sub-level caving. The computed forces experienced by the bucket during each mucking cycle are also discussed.

Jan 1, 2008

By Roberto Seno Júnior

O Processo Bayer para a produção de Óxido de Alumínio consiste em dissolver o alumínio presente na minério de alumínio (Bauxita) com soda cáustica à quente. Os resíduos insolúveis são separados por decantação e filtração. Após lavagem deste resíduo para a recuperação da alumina e soda cáustica ele é transferido para áreas de disposição. A Companhia Brasileira de Alumínio produz 420 mil toneladas de alumínio por ano gerando cerca de 2.400 toneladas de resíduo de bauxita por dia. Este resíduo é transferido para uma área de disposição, denominada Palmital, com capacidade de estocagem para mais 9 anos. Atualmente, o Palmital contém cerca de 2 milhões de metros cúbicos de água sobrenadante. Esta água contém alumínio e soda cáustica dissolvidos que podem ser reutilizados na Refinaria de Alumina. Este trabalho estuda formas de reutilização desta água sobrenadante visando aumentar a vida útil do Palmital, ou seja, aumentar o volume disponível para disposição de resíduo de bauxita.

Jul 31, 2018

By G P. W Suyantara, Y Tanaka, T Hirajima, Y Aoki, K Sasaki, H Miki

The effect of sodium sulfite (Na2SO3) on the flotation behaviour of bornite and tennantite is reported in this work. Flotation tests were performed using pure minerals of bornite and tennantite under various concentrations of sodium sulfite at pH 9. The flotation results indicated that sodium sulfite exhibited a depressing effect on the floatability of bornite in the presence of 0.1 mM PAX. However, tennantite remained floatable after the addition of sodium sulfite in the presence of 0.1 mM PAX. The flotation tests using mixed bornite and tennantite confirmed the flotation results of single minerals. Surface characterisation using X-ray photoelectron spectroscopy (XPS) was performed to explain the flotation results. A mechanism is proposed based on the XPS analysis results.

Aug 24, 2022

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By W. De Graaf, C. Mkumbo

Bulyanhulu Gold Mine Limited (BGML) commissioned a project of sinking a Bulk Air Cooling Shaft during its programme to improve the ventilation system on the mine. As part of this project, a ventilation drift had to be developed and holed into the Main Shaft at 4920 Level. AEL Mining Services (AEL) were requested to provide a technical solution, which included monitoring of blast induced vibrations and to design drilling and timing plans to ensure blasting activities on the vent drift were conducted without disrupting the main shaft’s infrastructure.

Jan 1, 2011

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By Kátia Cristina Gouveia

O objetivo deste trabalho foi determinar a TTDF do aço ASTM A36 com diferentes graus de encruamento após ensaios de impacto Charpy, sob diversas metodologias. Não se notaram diferenças no comportamento do material quando se avaliam os valores de TTDF obtidos pela medição da expansão lateral dos corpos de prova, nem considerando o valor da TTDF na qual o material apresenta 50% de fratura frágil, usando as metodologias de avaliação visual das faces de fratura dos corpos de prova, embora os valores sejam divergentes dos valores obtidos pelos métodos analíticos. A avaliação das faces de fratura dos corpos de prova por microscopia eletrônica de varredura permitiu visualizar que nas regiões onde visualmente considerou-se que havia apenas fratura frágil, também haviam regiões típicas de fratura dúctil. Conclui-se que a metodologia mais indicada é aquela que considera a TTDF como a temperatura na qual a energia absorvida é a média dos patamares superior e inferior, pois é um método simples, de fácil reprodutibilidade e que melhor refletiu a tendência de comportamento do material nos diferentes graus de encruamento estudados.

Aug 7, 2018

By Peter Moser, Andreas Grasedieck

In modern rock blasting it is becoming more and more important to achieve a certain specified fragmentation. This means that the rock particles formed as a result of the blast should conform to a desired particle size distribution. An important issue with respect to achieve a desired blast result in terms of fragmentation is both the availability of models for the prediction of the characteristic of the particle size distribution of blasted material and the determination of the energy necessary to achieve a certain fragmentation status. Within the research project “Less Fines” funded by the European Union under project reference G1RDCT200000438, the latter has been addressed by the Department of Mining Engineering& Mineral Economics of the University of Leoben. For that purpose fragmentation results from lab scale blast tests have been analyzed and the relationship between the specific charge used for the blasts and the resulting specific surface of the fragmented material has been examined. Linear relationships between the specific charge and the specific surface of the resulting fragmentation were found for various types of rocks to apply over a range of 10 for the powder factor.

Jan 1, 2004