Search Documents

By Ryan CG, Cousens DR, Suter GF, Griffin WL

A novel method utilizing PIXE with microbeams following fire-assay has been developed to determine PGE and Au at sub-ppm levels suitable for application in exploration. Analyses of the prills from the lead and silver fire-assay yield Pt, Pd and Au concentrations readily. NiS must be used as collector if the complete suite of PGE is required, but this method is not as Convenient.

Jan 1, 1989

By K. Sakaguchi, T. Yokoyama

"In-situ rock stress measurement was carried out in the Kamaishi mine of Iwate Prefecture to quantify the variation of the shallow crustal stress field associated with the 2011 Tohoku-oki earthquake. Stress measurement was conducted by the Compact Conical ended Borehole Overcoring (CCBO) technique, which is one of the stress relief method. The CCBO technique is the one of the suggested method of ISRM. Measurement period is from 1991 to 2014. Main results obtained in this study can be summarized as follows.The direction of the maximum principal stress did not change much before and after the earthquake. However, the directions of the intermediate principal stress and the minimum principal stress of one year after the earthquake changed from those of before earthquake. Namely, the direction of intermediate principal stress was East-West horizontally, and the direction of minimum principal stress was vertically. This state of stress is reverse fault type and was maintained for three years after the earthquake.The magnitudes of principal stresses and the vertical stress of one year after the earthquake became more than the double before the earthquake. However, the magnitudes of the maximum principal of two year after the earthquake became smaller comparing with those of one year after the earthquake. Furthermore, the magnitudes of the intermediate principal stress and the minimum principal stress of two year after the earthquake became almost same as those before earthquake, and the vertical stress of two year after the earthquake became almost equal with the overburden pressure. And the magnitudes of three principal stresses of three year after the earthquake became the same level before the earthquake."

Jan 1, 2015

By K Vallo, T Haimi, J Pihlasalo, J Hamuyuni, M Lindgren, F Tesfaye

Decarbonisation of the steel industry has recently attracted a lot of research and technological development. Most of the technological developments are centred around the replacement of blast furnace (BF), which has been the main primary smelting furnace in the ironmaking step of steel production. Replacement of the BF is not an easy task because of BF’s many established capabilities over the years, especially its ability to use low-grade iron feed. In this regard, Metso has developed its own technology, Metso’s Outotec direct reduced iron (DRI) smelting furnace, to tackle this problem. The recently developed six-in line electric furnace for DRI smelting can be used for primary smelting of DRI from blast furnace grade iron ore. Unlike the electric arc furnace (EAF), the DRI smelting furnace can handle larger slag volumes that emanate from the high gangue in BF grade DRI. Therefore, fluxing plays an important role in operating the DRI smelting furnace. This paper presents fluxing options and proposes slag quality and operating windows for the DRI smelting furnace. Also, the effect of slag on refractory durability will be discussed.

Jun 19, 2024

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By C. Mick Lownds, Dale S. Preece, Ali Bhuiyan

FDM (Fracture Density Model) is a three-dimensional mechanistic model of blast induced rock fragmentation. FDM uses several computational mechanics algorithms to simulate the effect of blasting in different rock types. Earlier, FDM was successfully exercised to simulate 29 small scale shots from the United States Bureau of Mines (USBM), and 6 full-scale bench blasts at the Bararp dimensional stone quarry in Sweden. Excellent agreement was obtained for those shots, and the results were documented in earlier publications. One of the drawbacks of previous ver- sions of FDM was its inability to predict the fines, specifically in Bararp quarry simulations. Ac- curate predictions of fines can be very useful in reducing energy consumptions during down- stream comminution processes and improve the mine-mill operation efficiencies. In this paper, we propose a newer algorithm that can predict the fines as well as the coarse fragments in Bararp with reasonable accuracy. The model was also applied to an open-pit Copper mine with heavily jointed rocks, and it produced very good fragmentation predictions for the full range of fragment sizes. Comparisons with the sieved fragmentation data (for both Bararp stone quarry and the open- pit Copper mines) show great potential for this updated version of FDM in modeling the entire range of fragment size distributions in mining and quarrying applications.

Feb 6, 2023

By Catia Moreira Casagrande

O processo de pelotização surgiu na década de 40. Até hoje, as qualidades químicas e físicas são utilizadas como controle e monitoramento do processo. Entretanto, a característica mineralógica e microestrutural do minério de ferro mostra grande importância para ajustes no processo, a fim de melhoria da qualidade do produto e redução de custo. As usinas de pelotização em Tubarão recebem minérios de várias minas do Quadrilátero Ferrífero, dificultando a caracterização de todas as misturas que entram nas mesmas. Com o intuito de obter maior eficiência nos dados de características do minério de ferro e processo, o uso de um software de estatística pode auxiliar no entendimento do comportamento do minério de ferro nas operações unitárias. Neste estudo, o objetivo foi relacionar à qualidade física do produto de moagem e pelota queimada por meio dos modelos preditivos, onde foi utilizado os tipos de minas, mineralogia e microestrutura como preditores. Com a análise realizada pela simulação e o conhecimento prático do processo foi possível correlacionar o efeito da mineralogia na qualidade física do produto do processo de moagem e qualidade física da pelota.

Oct 30, 2017

By Persifor Frazer

There is always a difficulty in assigning limits to the scope of a science or art, and among the dificulties of that kind besetting practical or stratigraphical geology is that of determining what kinds of natural objects shall be considered as the goals of its search. The term mineral, in its broader sense, includes every solid, liquid, or

By P A. Gibson, J R. Brinkmann

The South African gold mining industry fires approximately 800 000 sloping blastholes daily. A programme aimed at characterizing the stope blasting process is underway in order to identify areas for improvement and to provide blasting related information for the design of mechanized sloping systems.

Jan 1, 1985

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By F. A. V. Guimarães, A. M. Costa

"The moisture in sintering is a very important parameter for the performance of the process. It allows that the granulation takes pace in an efficient way making the water bridges between the bigger particles used as nucleus and the finer particles that perform the coating of those coarse particles. The formation of the micro pellets is extremely important to prevent loss in permeability of the bed in the sintering grate, avoiding excessive fuel consumption and producing a quality sinter. The aim of this project is to use some of the methodologies for determine the saturation degree on ores and coal to determine the optimal moisture for sintering. In the sinter pot grate series, 3 to 4 assays in a series of 10 are required to determine the optimal moisture for the process. The saturation degree curve test has shown that is really viable to use this technique to skip those tests and go directly to the series to determine productivity and the coke / anthracite consumption. In an industrial scale can be used to adjust the water addition in the conventional mixing methods used in the sintering plants to increase productivity in the process.INTRODUCTION Sintering Sintering is a high temperature agglomeration process in which iron ore fines are partially melted and bonded together using fluxes and a source of fuel, usually coke breeze. The agglomerated product, sinter, has improved metallurgical properties making it an ideal ferrous burden that enable the passage of hot gases in the iron-making blast furnace. The sintering process is normally carried out over three basic stages: granulation, ignition/sintering, and product sizing. In the granulation stage, iron ore fines (usually a blend of selected ores), sinter return fines, fluxes and fuel, and are mixed with water and micro-pelletised in a drum or disc before being introduced in the main granulation circuit. (Wang, Teng, & Wang, 2017)."

Jan 1, 2018

By Zhengbo Pan, Fujun Gou, Jifei Chen

This paper discusses the various alternatives that are technically feasible for "over-the-raise" continuous advancing in gently inclined coal seams and the computer-aided selection of the optimal mining option. Examples in Wangshiao Coal Mine and Chaohua Coal Mine are cited to illustrate the interval between raises, face length, single or double raise layout and single or double face layout.

Jan 1, 1983

By P. Barnes

The complete and uccurate filtration of water (if the word accurste map be thus Used) for the feeding of boilers, and for many similar industrial purposes, although somewhat practiced both at home and abroad, has heal by no means common. Even if the exact line cannot be defined at which filtration begins to be called for, ad will be found profitable, it is certain that in a large number of cases it may be employed with real advantage in the economy of fuel, and also in the greater durability of the boiler or other form of apparatus in

Jan 1, 1882

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts (CCB). Alkaline combustion byproducts are gaining increasing usage for acid mine drainage (AMD) mitigation as research leads to a better understanding of their beneficial applications. Since January 1997, Mettiki Coal has been injecting alkaline flue gas desulfurization material from Virginia Power&apos;s Mt. Storm Unit No. 3 wet limestone scrubber into abandoned portions of the active Mettiki Mine.

Jan 1, 1998

Although grinding mill liner life has been the subject of extensive studies, evaluation of the effect of liner design a power consumption, a far more significant part of total grinding costs, has been less comprehensive. The factors that effect ball mill energy efficiency are reviewed, and attention is then focused on the mechanism of grinding. The trajectory of the outer row of balls, with different lifting face angles, is derived. Basic recommendations for mill speed and liner configuration are also presented

Jan 1, 1984

By P. Barnes

THE complete and accurate filtration of water (if the word ,accurate may be thus used) for the feeding of boilers, and for many similar industrial purposes, although somewhat practiced both at home and abroad, has been by no means common. Even if the exact line cannot be defined at which filtration begins to be called for, and will be found profitable, it is certain that in a large number of cases it may be employed with real advantage in the economy of fuel, and also in. the greater durability of the boiler or other form of apparatus in

Jan 1, 1882

[ ]

Jan 1, 1938

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By G D. McDonald

Flinders Mines is an ASX300 iron ore explorer and developer with a tenement package located in the Hamersley Ranges region of Western Australia, approximately 70 km north of Tom Price. Exploration over the past three years has identified a Global Resource in excess of 740 Mt at a grade of 55.4 per cent Fe (+50 per cent Fe cut-off). This resource is spread across multiple deposits and has been divided into a number of mineralisation type domains based on geometallurgical and geochemical boundaries. These domains are comprised of transported haematite rich detrital iron deposits (DID) and goethite dominant Channel iron deposits (CID) as well as in situ bedded Brockman iron deposits (BID). On the basis of differences in physical and chemical characteristics, the DID have been divided into four discrete units. The four DID units form a stratigraphic sequence with the iron grade increasing and the contaminant concentrations decreasing with depth. The upper DID unit is lower grade and currently unlikely to provide a marketable product, without signifi cant beneficiation. The lower three DID units, together with the CID and BID, are of a higher quality and have the potential to yield marketable ore. The ability to define and recognise these different units has resulted in a more reliable and robust geological interpretation and hence greater confidence in the resulting resource model. This has been evident in the excellent conversion of inferred to indicated resources.

Jul 11, 2011