Search Documents

By N. ??dyanik, Z. Kugukaldinova, O. Mishurina, Y. Glazkova, E. Mullina

"This paper describes the process flow of a selective processing method for acidic mine waters formed in the copper sulfide industry and characterized by a high content of copper, iron, and manganese ions. The proposed method comprises a series of sequential processes: the 1st stage is the recovery of Cu2+ ions by precipitation, the 2nd stage is the recovery of Fe2+ and Fe3+ ions as a dispersed phase by acid-base precipitation, followed by recovery in the 3rd stage of Mn2+ ions by converting Mn2+ with an oxidizing agent into insoluble forms of manganese and subsequent recovery of the dispersed phase by electroflotation. The developed method was tested on the acidic tailing storage facility (TSF) water of a mining project in the Urals region. The practical results of the implementation of the developed method have shown that its implementation will allow to recover copper, iron, and manganese in the form of salable products with a simultaneous decrease in their concentrations in adjacent water bodies down to the applicable MPCs. The process is a simple one, does not require any sophisticated expensive equipment and can be implemented either as a standalone solution or as part of existing treatment facilities. INTRODUCTION As a result of unsustainable utilization of natural resources in Russia, only a small fraction is processed into commodity products, while the rest is systematically dumped as emissions, effluents, and other wastes, polluting the environment. By amount of waste and concentration of valuable components, those wastes can be classified as aqueous technogenic resources [1, 2]. Therefore, the development of processing methods for this mineral resource category is an urgent and priority task that will significantly improve the industry’s profitability and the environmental conditions in the respective regions. MATERIALS AND METHODS Following research methods were mainly applied in this study: lab-scale and pilot-scale tests in a diaphragmless two-chamber electric flotation cell; for solutions and recoverable process products — chemical analysis using photometric determination techniques for metal cations and atomic adsorption determination techniques for the processing products. The phase composition of the precipitates formed in the process was investigated by X-ray phase analysis in the general-purpose diffractometer with a copper anode DRON-1."

Jan 1, 2018

By Alicia Esther Ares, Alex Iván Kociubczyk, Verónica Liliana Scheiber, Roberto Rozicki

In the present research the horizontal solidification of Sn-Zn eutectic alloys (Sn-8.9wt.%Zn) is performed, with two opposite senses of heat extraction. From the process of solidification, the thermal parameters (local solidification time, cooling rates and interphases velocities) and grain sizes from macrostructures obtained were determined. The presence of defects in the solidified samples was analyzed, observing that they occur largely in the collision zones of solidification fronts advancing in opposite directions in the samples.

Jan 1, 2016

By Bowen Li, Jiann-Yang Hwang, Mingsheng He, Huaguang Wang

Kyanite is one of the major high-alumina minerals for producing refractory ceramics. At high temperature, kyanite can be decomposed into mullite and amorphous silica. This change is an irreversible decomposition and provides potentials for fiber reinforcement of ceramic matrix. In this study, kyanite powder was compressed into a cylinder green body of ceramic and heated at 1150–1450 °C.The phase transformation of kyanite and sinterability were investigated by X-ray diffraction and scanning electron microscopy. The results showed that the phase transformation of kyanite started at 1150 °C when rising the temperature. At 1350 °C, kyanite is completely converted into mullite and silica. The compressive strength of the ceramics reached 73.3–134.8 MPa, while the bulk density was 1.95–2.47 g/cm3. The microstructure indicated the correspondence of the compressive strength to mullitization degree of kyanite.

Mar 1, 2017

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By Art Frye, Lee Pratt, Gaichang Zhao, Greg Newman

This paper will discuss the Wight Pit wall slash at the Mount Polley open-pit copper-gold mine that scavenged a high grade block of ore from two double-benches of the pit wall. The Wight Pit orebody, discovered in 2003, is located in the Northeast of the property with the southeast pit wall approximately 50m (165ft) from the edge of Polley Lake. In early 2009, the Wight Pit was nearing completion while an estimated 150,000 tonnes (165,000 tons) of ore averaging a grade of 1.4% copper remained just inside the southeast pit wall. The ore block started 24m (78ft) above the pit floor and extended up another 48m (157ft) with a 70o plane defining the back of the block.

Jan 1, 2011

By Gisele Azimi, Jason Tam, Adrian Lambert

Many advanced technologies in modern society require the use of rare earth elements (REEs). Since these technologies are dominating the world, the demand for REEs is increasing fast. Finding new sources for them is highly of interest. One secondary source of REEs is phosphogypsum (PG), a by-product of the phosphate fertilizer industry. Microwave treatment is investigated as a method to enhance hydrometallurgical recovery of REEs from phosphogypsum, with results showing a 30% improvement in leaching efficiency.

Mar 1, 2017

By Allan Jansen, Robin Bissett

[Power-Point Presentation]

Jan 1, 2005

By Breno Totti Maia

Na conjuntura atual, o foco dos produtores de aço tem se voltado fortemente para a otimização dos recursos e do tempo. O AOD é um convertedor de aços inoxidáveis. A intensa agitação do banho obtida pela lança de topo e injeção de gases por ventaneiras geram projeções ao longo do processo com formação e acúmulo de cascões na parte interna do cone superior. O excesso de cascão prejudica as operações de carregamento e vazamento das corridas. Visando reduzir o acúmulo de cascão, foi desenvolvido para o AOD da Aperam South America, a partir do conceito da lança Slagless um módulo de pós-combustão. Os furos de passagem de oxigênio deste módulo ficam posicionados na região onde se alojam as projeções de metal e escória. Os resultados iniciais obtidos com a Slagless Clean Up desenvolvida mostram uma evolução na qualidade da limpeza da boca do AOD, facilitando a operação de carregamento do forno. Ao longo do período foram feitas alterações na abertura dos furos de pós-combustão para adequação das vazões de sopro. O projeto, agora já na sua fase de conclusão, deverá passar por ajustes na quantidade e na distribuição dos furos do módulo de pós-combustão.

Aug 15, 2017

By Chuanyao Sun, Yang Yu, Zhen Guo Song, Wei. Ming’An

"Carbonate minerals are very important mineral source of extracting metal, radioactive element and rare earth elements. Furthermore,some carbonate minerals, such as calcite and dolomite, are common and important components of sediments and sedimentary rocks. Many flotation processes involve the separation of valuable minerals with carbonate minerals. So it is of great significance to the flotation theory and industrial practice to investigate the flotation behaviors of carbonate minerals. As regulators, metal ions play a major role in minerals flotation. The study of influence law of metal ions on minerals flotation is helpful to eliminate or utilize the effect of metal ions. In this study, calcite and smithsonite laboratory scale flotation, surface analysis and zeta potential determination in the presence of Fe(II) ion were performed to investigate the effect of Fe(II) on carbonate flotation. The results show that Fe(?) depresses the flotation of calcite and smithsonite. The depression effect of Fe species on calcite and calamine flotation can be improved with the increase of Fe(?) concentration. The zeta potential measurements and surface analysis show the existence of iron hydroxide products on mineral surface, which may be link to carbonate site instead of exchanging with calcium on the mineral surface. Fe species on the mineral surface inhibit the interaction between the reagents and calcite/smithsonite through the formation of surface precipitation coating on the calcite/smithsonite surface when the Fe(?) concentration is higher."

Jan 1, 2014

By John D. Nelson

Jan 1, 1985

By William Newnam

WHEN Hugh Lee Pattinson discovered, in 1829, that the crystals formed during the slow cooling of molten lead were poorer, and the remaining liquid richer in silver, than the original lead, an important step was made in the metallurgy of this metal. Being the first process applicable to the desilverization of low-grade lead bullion, it soon found its way into all European countries having such a product to treat, thereby effecting the saving of many ounces of silver annually which previously had been thrown away. The old hand process was expensive, as viewed from the standpoint of more modern methods; the labor was great anti the tonnage was small, but on the other hand the results were fairly, satisfactory. This process flourished for some time after the introduction of the cheaper Parkes process in 1852 and it is still in use in a few European smelteries. Only one notable improvement was made on the original process, that of Luce and Roan at Marseilles, France. It consisted in the application of steam for stirring and the tapping of one-third of the liquid lead, through perforated plates covering the tap holes flush with the bottom of the kettle, thus leaving two-thirds in the form of crystals in the original kettle. This modification considerably lowered the operating costs as it permitted of much larger kettles, an increased tonnage and eliminated much of the slow, hard labor of the hand process.. The Luce and Rozan process has persisted in its original form to the present clay. Stephen Tredinnick, English born, spent most of his years around the Luce and Rozan plants at Marseilles and elsewhere in Europe, coming later to Eureka, Nev., in 1878, to operate the Luce and Rozan plant at that point. Mr. Tredinnick was a competent Luce and Rozan operator and being devoted to the process he firmly believed that with modifications the costs could be so lowered as eventually to supplant the Parkes process.

Jan 5, 1917

The Mammoth Copper Deposit consists of three distinct orebodies adjacent to the Mammoth Fault. This fault is arcuate, changing from a normal tension fault to a shear strike fault just to the north of the mine. Movement on the fault was probably contemporaneous with deposit- ion of the adjacent sediments. In the upper levels the No. 1 orebody occurs within a brecciated zone in the footwall of the fault, but at depth the No. 2 and 3 orebodies are stratabound by two brecciated lithologic horiz- ons. The host rocks are impure sandstones, arkoces and quartzites, which in the mine area are near the top of the Lower Proterozoic Myally Beds. Overlying these beds is a conglom- erate siltstone sequence which has been assumed to be the base of the Gunpowder Creek Formation. North and south of the mine the conglomerate rests on an erosional unconformity representing a major time break, but in the mine the uncon- formity and conditions of deposition of the conglomerate are obscure. Some mineralization is contained within the conglomerates. The sulphides present are chalcocite, bornite, chalcopyrite and pyrite. Chalcocite is dominant in the upper levels but could be en- riched by supergene processes. At depth, bornite becomes the dominant copper sulphide with lesser amounts of chalcopyrite, pyrite and primary chalcocite. Throughout the orebody minor digenite and covellite occur and arsenic is a minor constituent bound up with the pyrite. The bulk of the sulphides occur in stringers, fractures and breccia interstices but finer grained primary bedded sulphides can be observed. The genesis is probably a complex process in- volving active tectonic movements extending from deposition to post lithification giving numerous phases of brecciation and redistribut- Ion.

Jan 1, 1974

By Yosuke Ota, Makoto Tawara, Tetsuya Kojima

"Dry-lube has been used in Europe to enhance formability of aluminum sheet for automotive applications, but it is difficult to ensure degreasing performance with lower degreasing bath temperature. However, newly developed, highly lubricating pre-coats utilizing a urethane resin, which is soluble in water, have been found to show excellent degreasing performance. Furthermore, a richer pre-coat weight coincides with a lower friction coefficient and better formability. Combined use of anti-rust liquid oil showed different friction coefficient depending on applied surface pressure.INTRODUCTION The global demand for aluminum alloy products, especially for automotive application, has been increasing because aluminum alloys can offer excellent corrosion resistance with good strength and low density compared with steel. Aluminum alloys can contribute to saving much more energy and greenhouse gas emissions over the lifetime of the product. On the other hand, the amount of aluminum alloys in vehicle architectures is still somewhat limited due to relatively low formability. As a consequence of this low formability, it is necessary to set a certain limit to the shape of an aluminum alloy panel for automotive applications. So far hot melt wax dry lubricants have been in use especially in Europe as they have been recognized to provide better lubrication than conventional rust protection oils (Meiler & Jaschke, 2005). The benefit of hot-melt wax for automotive manufacturing is associated with a more stable forming process and the possibility to avoid extra lubrication in the press shop. But because of the low poorer solubility of hot-melt wax in degreasing aqueous bath solution, a higher degreasing temperature is required so that no remnant of hot melt wax can be carried over to the next manufacturing process. This temperature control is difficult to impress upon a manufacturing degreasing bath originally designed for liquid oil, especially in Japan. The typical temperature of degreasing bath in Europe is around 60°C, while it is only around 40°C. in Japan. Various types of pre-coats other than hot-melt with high lubricity have been reported (Tawara, 1993; Ueda, Hatsuno & Totani, 2013), but a balance between sufficient degreasing performance and high lubricity has not yet been achieved for an actual production process line."

Jan 1, 2018

By T Napier-Munn, D J. Bradshaw, M Chauhan, L Keeney

An important aspect of geometallurgy is quantifying mineral processing attributes, which leads to improved orebody understanding. One of these attributes is flotation performance. Several methods have been developed as indicators for flotation performance, including batch testing leading to kinetic information and the standard grade-recovery curve. This paper makes a preliminary statistical comparison between a newly proposed geometallurgical batch flotation procedure and the æstandardÆ batch flotation test commonly used to measure flotation performance in the laboratory. The new test uses much less material than the standard test, and is much faster. It is concluded that the new method follows the final recovery of the standard method well, suggesting that it will be effective in reflecting ore variability for geometallurgical purposes. Comparison of the methods based on the full grade-recovery curve shows less agreement, but this may be due to the fact that the curve is sensitive to the particular experimental set-up and conditions, which make such comparisons quantitatively challenging. Further development work is therefore planned.CITATION:Chauhan, M, Napier-Munn, T, Keeney, L and Bradshaw, D J, 2013. Progress in developing a geometallurgy flotation indicator, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 201-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By BUREAU OF MINES

LIST OF PUBLICATIONS ON CERAMIC INVESTIGATIONS U.S. BUREAT OF MINES .

Jan 1, 1923

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Manoel Farias Martins

A utilização de antracito na produção de pelotas de minério de ferro é uma prática utilizada pelas mineradoras para reduzir custos com combustíveis e melhorar a qualidade física do produto. Objetivando uma melhor compreensão dos efeitos ocasionados pela adição de carvão na mistura (pellet feed moído e aditivos) sobre a resistência a compressão das pelotas queimadas, foram confrontados os resultados dos ensaios de resistência à compressão obtidos através da rotina de ensaios da mineradora VALE SA, com as seguintes variáveis: percentual em massa de carbono (%C fixo), porosidade e granulometria do antracito. Com a elevação de carbono, observou-se a redução nos valores da resistência à compressão, sobretudo, nas pelotas de redução direta. No que diz respeito à porosidade, a resistência à compressão das pelotas aumentou com a diminuição dos poros no interior das mesmas. Analisou-se também a granulometria do carvão, todavia, constatou-se que a mesma não teve influência significativa sobre os resultados da resistência à compressão.

Oct 30, 2017

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By J Evans-Wheeler

"The mandate of the 2005 VALMIN Code to provide ‘(all) reliable, thorough, understandable material information required by investors and their advisers when making investment decisions’ requires that due diligence for tenure be full and thorough. Yet a published due diligence would often appear to be simply a list of tenures allegedly held without any commitment as to the standing of the tenure as safe and secure or otherwise.The value of due diligence for tenure, as mandated in the 2012 JORC Code and the 2005 VALMIN Code, must focus on compliance rather than simply on ‘vital statistics’. Enforcement in every jurisdiction in Australia focuses on penalties (some more harsh than others) for non-compliance, which, in turn and most importantly, reflects directly on security of tenure. Some 22 Acts (on average) impinge on security of tenure and fundamentally underpin the security of any mineral asset.This paper will outline regulatory processes to demonstrate how tenure compliance is achieved and argue that the rigorous application of good practices in tenure evaluation will lead to more of this information being made available on a regular basis.The paper will then focus on further practical examples of tenure compliance failures, the application of these to the requirements of the JORC and VALMIN Codes and due diligence that failed to fulfil the mandate. Examples will be given that alerted other professionals using the JORC Code to complex geological and mining situations of which they were unaware in their valuations.Finally, the author will make a personal plea for tenure to be considered at the commencement of any reporting process.CITATION:Evans-Wheeler, J, 2016. The VALMIN code and tenure compliance – not just a list, in Proceedings Project Evaluation 2016, pp 112–121 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020