Search Documents

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

By Murray Pezim

In the good old days of the folklore of the mining industry, grizzled prospectors obtained a few loose dollars from friends and neighbours then wandered off to eventually return with the great discovery which became the core of the new corporate empires. Alternatively, merchant banking barons obtained exclusive rights to just about anything of future value over hugh nation-size territories. Some of this probably still goes on, likely with about the same ineffectiveness and waste of effort and money as in the past. CURRENT CONCERNS IN MINING In today's difficult climate in the mining industry, for that matter in all industry, effectiveness is the vital consideration. Cost effectiveness -- more bang for the buck -- is especially important in such an area of high risk as mineral exploration. And there are other factors to consider. Since minerals are depleting resources, the mining inddustry is constantly confronted with the reality that those resources extracted today must be immediately replaced if a resource enterprise is to continue. And if growth is to be achieved, even more resources must be found to support future expansion. The current and immediately foreseeable climate internationally for the mining industry creates a special need and urgency for aggressive and successful exploration, certainly in Canada, if not also in the United States. Depressed world markets and prices have turned yesterday's economic reserves into today's waste, hopefully to be converted into economic ore again in some distant time. One way of replenishing reserves and maintaining a viable mining industry is to find and develop mines which are economic under short-term depressed price and market conditions. This probably means higher grades. A new copper discovery with the right combination of characteristics to be an attractive investment even at today's pices for copper would still merit development into production. Exploration is the only way to find such mines for the difficult short-term conditions. Another important consideration is that normally many years stretch from the first thought of conducting exploration to production -- in those rare instances where an economic discovery is made. If discoveries are not made today, then there will not be any projects to develop when business conditions are more attrative. This industry and the vast number of skilled professionals who are part of mining, are faced with two key problems that underlie the need for a junior exploration segment. One consideration is how to maintain exploration during those years, indeed eras, of recession and depression. We are in such a time now. Throughout the world, major companies have sharply cut back, if not eliminated completely, exploration expenditures other than what is vitally necessary and easily and inexpensively done at the known and producing deposits. And related to that consideration, even more important today than during happier times, is how to finance such necessary ongoing exploration if major companies and governments back away because of financial stringency. CANADIAN SUCCESS In Canada, such problems are being tackled with a success which is capturing worldwide attention. The ability of mineral explorers to obtain willing, eager, high-risk capital is achieving even more outstanding results than in the past. These results are reflected in the widespread continuing exploration ativity in Canada which even spreads into the United States, with some outstanding discovery successes. The most notable exploration success from junior mining activity is the discovery of the Hemlo gold camp in northwestern Ontario, a source of gold which promises to rank with the South

Jan 1, 1985

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By Pedro L. Lizaur

INTRODUCTION The degree of success of an association between parties in establishing a new venture ultimately depends on three factors: a. the venture's underlying economic strength, which is based on the complementarity of the comparative advantages brought by each party to the negotiating table; b. the ability to reach an agreement which satisfies each party's objectives and constraints; and, c. the capacity to design and implement a funding structure which is consistent with the project economics. A thorough assessment of the venture's profitability and associated risks under alternative technical and economic scenarios is the basis for a sound "go" or "no go" decision. In-depth evaluation of the risks and rewards to each of the parties involved under alternative legal and financial structure must be the foundation for a long lasting "how to go" decision. The allocation of risks and rewards should be consistent with the objectives and constraints of all parties and the sharing mechanisms, established in the contract, should be flexible to assure the long-term stability of the agreement. Rapidly changing economic conditions during the last decade have had a dramatic impact on the envisaged allocation of risks and rewards between host countries and private investors. The effects of these changes, and the fact that the relative strengths of the parties involved may shift during the life of a project (e.g. before and after major capital investments have been made), have forced the renegotiation of a multitude of contracts. Therefore, the present and future stability of an economic agreement would depend not only on the originally designed provisions, but also on provisions which allow for the automatic adjustment of rewards to project sponsors under a variety of future economic situations. A pre-condition for the allocation and quantification of risks and rewards is the definition of standards of measurement used by each of the parties. This is critical in international negotiations when one of the parties represents the national interests of a country. The understanding and use of different standards for the measurement of rewards for risk taken between a government and private enterprise facilitate the negotiation of a satisfactory agreement. This is possible because certain trade-offs between the negotiating parties may have different relative values. STANDARDS OF MEASUREMENT OF REWARDS FOR RISK TAKEN The negotiating process takes a step forward when the parties are able to focus on their interests, explore different alternative solutions and then base results on a set of objective standards. Unfortunately, the parties frequently put more effort into "staking out" and defending positions, than into understanding their intrinsic interests. Moreover, when one party, such as a governemnt owned corporation, represents a country's national interests, the negotiation process increases in complexity. Private firms focus on commercial profitability, using discounted cash flow techniques such as NPV, IRR, or ROE. In contrast, the government is also concerned with the project's impact on the local socio-economic environment. Without entering into a discussion of alternative economic development theories and approaches, there exist several possible measures that could be pragmatically utilized by each party in evaluating the socio-economic impact of a project. The more complete measure is the National Profitability (NP). The NP is a discounted cash flow procedure similar in structure to IRR or NPV but in which the project's financial cash inflows and outflows and discount rates are adjusted to take into consideration the local conditions. The NP is calculated on an unlevered basis and all taxes and duties are removed from the project

Jan 1, 1985

By H. D. Attra

The effects of phase behavior on reservoir economics is a function of both fluid composition and flow properties of the reservoir rock. In some operations such as gas injection into volatile crude-oil resertoirs, the stock-tank recovery derived from vaporization of the reservoir oil by the displacing gas can approach the recovery derived from the displacement mechanism. In other cases of gas-cycling reservoirs, the dry injected gas can effectively vaporize a retrograde liquid phase, allowing a substantial reduction in cycling pressure with no appreciable loss in recoverable liquids. Because of these effects, it is essential that phase behavior be considered in developing the economics of any secondary recovery program in which gas is the injected fluid. The inclusion of phase behavior in conventional calculation procedures has been retarded because of the complexity of the calculation and the large volume of laboratory data required. However, by applying high-speed computers and new laboratory techniques, the phase-behavior displacement calculation has been developed to economically include this basic fundamental of gas displacement. The calculation is performed by reducing the reservoir to a series of one-dimensional segments. Phase changes, saturation distributions and changing fluid properties are evaluated for each segment as a function of time. The relative volumes of equilibrium liquid and gas displaced from each segment are determined by a trial-and-error procedure to meet the requirements of phase equilibrium and two-phase flow. The produced fluids are flashed through conditions of surface separation approximating those in the field to obtain actual values for stock-tank liquid recovery and producing gas-oil ratios. Based on the results of successful field studies, the technique appears to have application to reservoirs producing under a nonmiscible gas-displacement mechanism and should substantially increase the reliability of this type of analysis when phase behavior is an important factor. Predicting reservoir performance under gas-injection operations involves three basic principles of reservoir engineering. First, a material balance exists between the displacing gas and the displaced reservoir fluid. Second, the oil and gas flow in relationship with the two-phase flow property of the reservoir rock; and third, phase equilibrium exists between the displacing gas and the native reservoir fluid. To illustrate these three principles, consider the one-dimensional reservoir shown in Fig. 1. The reservoir is divided into a series of segments representing a one-dimensional cross section between an injection area and a producing area. So represents the oil saturation, Cw represents the connate-water saturation and Sg represents the displacing gas saturation. The gas is moving into Segment 1 and the reservoir oil is being produced out of Segment N. Consider the case when gas has just moved into Segment 1 and the displacing gas-oil contact is at position a-a The volume of oil pushed out of Segment 1 is a function only of mobility and the two-phase flow properties of the reservoir rock, that is, Kg/Ko and µo/µg. Behind the front if the injected gas is foreign to the reservoir oil (a nonequilibrium gas), there will either be vaporization of the oil into the gas or condensation of the gas into the oil. In either case the net result is a mass transfer and a re-distribution of composition and liquid and gas saturation. If the displacement is at constant pressure and is continued, the gas moves into new segments, proceeding succesively into Segment 2, 3, etc. The total volume of oil produced from the reservoir

By Klaus M. Zeitler

INTRODUCTION One cannot discuss the subject of "Raising Capital in the 1990s" without having a crystal ball and a reliable fortune teller. This discusses "Raising Capital for the 1990sW, which is what Metal1 Mining Corporation did in 1987. We raised (3166 million in an IPO (initial public offering) that was originally planned for only some (375 million. Why did we raise this money? How did we do it, and why was this IPO so successful? The answer to the first question requires a description of the promoter and principal shareholder of Metal1 Mining Corporation, Metallgesellschaft AG. This West Germany company was founded over 100 years ago in Frankfurt as a trading house for non-ferrous metals. It has developed into one of the world's leading firms in the non-ferrous metals industry. The company's worldwide activities in all areas of that business include mining, smelting and refining, the trading of ore, base and precious metals, the production of semi-fabricated and finished metal products, and the provision of engineering, construction and transportation services. Metallgesellschaft AG has also diversified into many other areas, the most significant of which are manufacturing, the production of chemicals, the development and application of technical and chemical processes, the planning and construction of industrial plants, and activities associated with finance, insurance, shipping and freight forwarding, and the provision of barter and countertrade services. The company maintains a network of more than 100 offices around the world; it employs some 25,000 people in its worldwide activities. [Selected financial data, as of September 30, 1987: (MetaUgesellschafl AG) Working Capital DM 8%.6 million CDNS 672.8 million Long Term Debt DM 568.0 million CDNS 426.2 million Sales DM 14.9 billion CDNS 11.2 billion Net Income DM 87.7 million CDN$ 65.8 million Market Capitalization at April 27, 1987: (Metallgesellschafi AG) Outstanding Shares ~,6oo,o0o DM 1,875 million CDNS 1,407 million] For the fiscal year ended September 30, 1987, Metallgesellschaft AG had, on a consolidated basis, net sales of DM13.3 billion, net income of DM100 million and total assets of about DM7.0 billion. Metallgesellschaft AG established the American Metal Company, a predecessor of AMAX Inc. one of the largest ventures undertaken by Metallgesellschaft AG then was the acquisition, through the American Metal Company, of a majority share in the Mexican Penoles mine, a large lead and silver deposit. METALLGESELLSCHAFT AG Figure 1 depicts an overview of Metallgesellschaft AG before and at the time the initial public offering of Metall Mining Corporation's shares took place. It shows that mining was far from the centre of Metallgesellschaft's activities. Therefore, it could not expect to receive an extraordinary amount of board attention. Thus, mining investments not only had to compare well with other mining opportunities, but were in fierce competition with projects from other divisions. In addition, mining was sub-divided into two separate departments -- domestic and international. These two departments had different management styles and diverging interests which resulted in a minimum co-operation between them. The domestic mining department was primarily interested in the survival of the local mines. These mines were characterized by rising operating costs and declining ore grades. It took a special commitment and continued ingenuity to develop and adjust to local conditions, and modern mining and processing technology, in order to remain competitive, or at least survive within the international mining industry. Local management

Jan 1, 1990

By David B. Reger

The expansion of the previously discovered gas pools and an intensified search for additional pools in the Oriskany and deeper sands were the principal petroleum activities in West Virginia during 1941. One small oil pool was discovered and another was considerably extended. One small gas pool was discovered, several isolated well discoveries were expanded into definite pools, and various recognized pools were substantially increased. The proved oil territory of the state was increased about 600 acres and the proved gas territory about 45,000 acres. The new discoveries of oil did not equal withdrawals but gas reserves added were greater than gas withdrawals. Oil activity, as in the past several years, was slight because of unfavorable crude prices. Most operators prefer to leave oil in the ground rather than to drill for it without a better return. Gas activity increased greatly because of better demand, even though the price of gas did not improve. The account of operations, as gathered from trade journals and other reporting services, shows that 838 new wells were drilled, resulting in 114 new oil wells with 2606 bbl. of daily new production; 558 new gas wells with 949,226,000 cu. ft. of daily open flow; and 166 dry holes. Also, 86 old wells were drilled to deeper sands with 9 bbl. and 56,030,000 cu. ft. of added production. On the new wells the oil average was 22.86 bbl. per well per day; and the gas average was 1,701,000 cu. ft. per well per day. On new wells the ratio of dry holes to completions was 13.61 per cent. On deeper drilling to other sands the ratio of failures was 15.12 per cent. From an exploratory standpoint one strictly new oil pool (Higginbotham Run) was opened in Kanawha County and one strictly new gas pool (Lost Run) in Taylor County. One entirely isolated wildcat gave commercial Oriskany-sand gas production and may open a pool. Various other wildcats greatly extended the boundaries of known Oriskany-sand gas pools and various others may have opened new pools in the shallow sands. On the other hand, various Oriskany tests in Harrison, Monongalia, Roane and Wood Counties were dry and all five tests to the White Clinton sand (Sil.) in Boone, Harrison, Kanawha and Wood Counties failed to find commercial production. The principal oil wells completed, by counties, were: Calhoun, 24; Clay, 7; Gilmer, 6; Hancock, 9; Kanawha, 9; Pleasants, 10; and Ritchie, 14. Production for the year was estimated by the Oil Weekly as 3,421,000 bbl., compared with U. S. Bureau of Mines final figures of 3,444,000 bbl. in 1940. The leading counties in gas-well completions were: Boone, 32; Braxton, 19; Cabell, 16; Calhoun, 46; Clay, 20; Gilmer, 37; Jackson, 94; Kanawha, 82; Lincoln, 17; Putnam, 46; Ritchie, 33; Upshur, 20; and Wayne, 33. Production for the year is estimated by the author as 210,000,000,000 cu. ft., as compared to the U. S. Bureau of Mines' final figures of 188,751,000,000 cu. ft.* in 1940.

Jan 1, 1942

Develop and demonstrate a lightweight material that has low thermal conductivity and that would be suitable for placement using shotcrete methods. This material could be applied in deep, hot mines where mine drifts must be insulated. Its use would decrease mine refrigeration needs and reduce energy costs.

Jan 1, 1994

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By V. J. Driscoll

A method is given for checking pore volume reserve estimates and transient water inflzix factors utilizing early well performance. Principal applications are based on the observation that there is a convenient transient time-range in terms of well spacing in which observed pressure drop will give a good indication of fluid-in-place. Primary quantity determined is a porosity-feet value applicable in the vicinity of an observation well. Checks on porosity or net pay thickness and permeability values also are obtained. These are particularly valuable in improving quality of interpretive factors entering into pore-volume reserve determinations for larger fields. In smaller fields, direct determination of total field reserves and approximate location of boundaries may be made in some cases. Well interference and production data plus a build-up curve on the observation well are needed. The build-up curve may be taken at any time. Field applications are given. The method can be applied with the completion of the second well on a new discovery or to older reservoirs by major changes in withdrawal rates from a local area. Appropriate test length permits results to be obtained with equal accuracy on widely spaced wells. Criteria for optimizing test conditions are given. Provision is made for various boundary and well effects including incomplete observation well build-up. INTRODUCTION Due to low quality data, initial pore volume reserve and water influx estimates may often vary by a factor of two or more from results obtained at a later date. Unfortunately, by conventional methods, more reliable answers from performance usually are not available until after most significant economic decisions have been made. Furthermore, in older reservoirs, uncertainties may still exist as to original oil-in-place, recovery factors and residual oil saturations due to incomplete or inaccurate performance data. This paper outlines situations and appropriate arrangements of basic transient theory whereby well interference data can be utilized to improve the quality of estimates under certain conditions. In addition to production data on offset producers, key information required is a measured pressure drop at an observation well, corrected for any incomplete build-up due to previous production, plus a formation capacity value derived from a conventional pressure build-up plot on the observation well. The method, as outlined, is strictly applicable only to a horizontal single-layered system of uniform rock characteristics containing a homogeneous fluid of low and constant compressibility. However, under the set of test conditions devised, requirements can usually be relaxed so that it should be applicable to most low permeability gas, water and undersaturated oil reservoirs. This is an area where more reliable information is certainly needed. BASIC CONSIDERATIONS A, B, C and F as subscripts or in the text refer to producing Well A, observation Well B, a more remote producing Well C and field boundary F. Combinations such as AB refer to distances and dimensionless times in terms of distances between these points, while single letters refer to distances and dimensionless times in terms of the well-bore or field radius. Equations covering definitions of quantities and complex situations are given in the Appendix. Key equations in practical units are given in Table 2. Transient Pressure Behavior Fig. 1 illustrates pressure drop at Point B with time due to initiation of a constant rate of withdrawal from Point A. This is shown as since a quantitative under-

"Copper was first made in Butte by the use of iron for its precipitation from mine water in 1890. In consequence of a fire breaking out in the St. Lawrence mine of the Anaconda Copper Mining Company in November, 1889, a large quantity of water was poured into the workings, with the intention of flooding the mine and extinguishing the fire. This proved to be impracticable, but this water, on being pumped to the surface, was found to be high in copper sulphate,—tradition says 75/100 of 1 per cent. The Anaconda Copper Mining Company gave Wm. Ledford a lease on this water. He first (lug holes into the ground, filled them with scrap iron and allowed the water to flow through them. Later he built an open-top flume which he partially filled with iron and passed the water through the by the iron precipitation method. An assay in- the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level.None of the mine waters encountered in the solid rock in the mines of Butte contained copper in sufficient quantity to produce the metal profitably by the iron precipitation method. An assay in the year 1890 from Gagnon mine water, showed .0016 per cent or 28 lbs. copper per day. The mine was then opened to the 1,000 level."

Jan 1, 1913

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

By Brown, R. W., G. H. Neill, R. G. Loper

All facets of ball sealer behavior must be known and understood to design for their optimum use in well treatments. The down-hole factors including the inertial forces, drag forces and holding forces have been discussed. Equations have been developed and presented for these forces. The use of these equations in this process will contribute to the most efficient use of an economical and proven ball sealer process. The urocedure presented has been used to successfully analyze field results indicating problems involving the use of ball sealers. These problems have been isolated and corrected in future treatments by using the procedure presented to revise the perforating program, the injection rate, the design of ball sealer stages and/or the type and size of ball sealers. The procedure presented also indicates that dislodgement of ball sealers occurs primarily in ultra slim-hole completions. INTRODUCTION The perforation sealing process has been proven highly successful and economical since it was introduced to the oil and gas industry in early 1956.' Since it has proved so successful in multistage fracture treatments at a much lower cost than conventional packers, the ball sealer process has become a byword in well completions.' Not only has it changed the design of fracture treatments, it has changed the concepts of selectively perforating and has greatly aided the success of the single-point and limited-entry techniques." Yet with all the advantages, there are still facets of ball sealer behavior that are not widely recognized. These must be known and understood to better design and execute the optimum ball sealer treatment. The down-hole behavior of ball sealers is influenced by a number of factors including an "inertial force", a "drag force" and a "holding force". These are considered in two phases—the initial seating of the ball and the forces tending to unseat the ball after contact has been made (see Fig. 1). This paper presents a theoretical study of these factors and formulas for predicting their influence. The authors acknowledge the fact that the flow equations presented herein describe the behavior of Newtonian fluids and do not cover the so-called power-law fluids. The assumptions made, however, are reasonable and well within practical limitations of the conditions encountered during field application. For example, it is assumed that the perforations are round with a discharge coefficient of 0.82. While this may not be exactly true, it has been verified within practical field limitations.' The discharge coefficient would not vary significantly even if the perforation size or configuration varied pronouncedly. The approach of assuming uniform perforation size is not as strained as it might first appear. Normally, a perforator contains charges equally spaced with the same number in each vertical (or horizontal) plane. If the perforating gun is not centralized, the holes in one plane will be smaller than average, while the holes in opposing planes will tend to be larger than average. The net result is that the two effects tend to balance. FACTORS AFFECTING CONTACT WITH PERFORATlON Ball sealers are injected into well treating fluids for the purpose of contacting and sealing those perforations which are accepting the fluid flow. The efficiency of the sealers is primarily influenced by: (1) the velocity of the balls down the pipe, and (2) the fluid velocity through the perforations. To divert the sealer to the perforation, the inertial force of the ball must be overcome by the drag force created by the fluid velocity through the perforation. BALL VELOCITY The final, or stable, velocity of the ball is the sum of the actual fall velocity and the fluid velocity. This will be

By Dirk van Zyl, S. Chander

Minerals have been critical to human society from the earliest and their use has been intertwined with the development of civilization. In the Western World, the mining, processing and extractive metallurgy associated with ores was first described in detail by Agricola in the 16th century. He considered these collective activities to be the most necessary and the most profitable of professions, and wrote, "without doubt, none of the arts is older than agriculture, but that of the metals is not less ancient; in fact they are at least equal and coeval, for no mortal man ever tilled a field without implements. In truth, in all works of agriculture, as in the other arts, implements are used which are made from metals, or which could not be made without the use of metals; for this reason the metals are of the greatest necessity to man." Ours is still a materials-dependent society that relies heavily on minerals for raw materials. Today our dependence on minerals is exceptionally great. To meet the need for fuel and non-fuel minerals in a representative year, in the United States alone, about one billion tons of coal and 2.7 billion tons of ore are mined. These mineral products are essential for fertilizers, for construction materials, metals and alloys, for manufacturing household and industrial items, for transportation, and for the generation of electric power. It is instructive to consider the diversity of uses found in our society for a single mineral product - silver, for example. Experts believe that in the past 5000 years we have mined about a million tons, or 31.9 billion troy ounces of silver. In 1988, 133 million troy ounces of silver were used in the Unites States. Most of the silver used was for techno- logical, medicinal and industrial purposes, Table 1. X-ray films, for example, carry comparatively large amounts of silver to lessen patient's radiation exposure. Silver does not prevent tooth decay, but each year about two million troy ounces of silver is used for dental work in the United States. In small quantities it is used in medicine. No metal - not even copper conducts heat and electricity so efficiently as silver. Silver wires lace solar cells, and silver oxide batteries power hearing aids, calculators, submarines and satellites. Hardened with tungsten or molybdenum, miniature discs of silver pass current from wire to wire in cars, telephones and computers. A dish- washer timer alone may have 50 such electrical contacts, which open and close without excessive heat or friction. Silver is an important component of solar reflectors, since no other material reflects light so well or uniformly. In our personal lives, silver remains in high esteem to adorn our tables, provide precious objects and jewelry. In many parts of the world, silver in the form of coins, jewelry and bullion is used for financial independence and security against the vagaries of paper currency. In India, silver is used in its purest form as thin foils to decorate sweets and other edibles. It is obvious that this mineral product, silver, is of great value and utility in our society. Minerals and Environment The benefits of minerals do not come without problems. Much of the silver, for example, lies locked up in copper, lead-zinc or precious metal ores; to extract it creates vast quantities of waste material. On the average, in order to recover one ounce of silver about a quarter ton of ore must be mined. To meet the world's annual demand for silver, approximately 100 million tons of waste is generated every Year. The problem with silver is repeated with all minerals. Conversion of mineral ores into usable materials necessitates the generation of large quantities of waste products that create tremendous disposal problems. In addition to waste material discarded during mining, wastes may be generated during processing as gases, liquids or solids that must be subsequently converted into forms more acceptable for disposal. Associated with the handling, treatment and management of waste products are a number of environmental problems. Environmental problems are not new to the minerals industry. In his Geographia, Strabo (63 B.C. - 20 A.D.), gives an account of the conditions of labor under which men

Jan 1, 1992

By R. T. DeHoff

A general method for determining the geometric properties of structures composed of particles which are all the same shape and size is presented. The application of the method requires a knowledge of' the qualitative shape of the particles in the structure, ad a maximum of three simple counting measurenzents, which are made on a representative plane section taken through the structure. It is also shown that the number of different kinds of measurements necessary JOY the complete description of the structure can be decreased if some independent information about individual particles is available. The geometric properties that can be determined quantitatiz~ely from counting measurements for susch structures are size, shape, number, surface area, vlolume, ad such extensive properties as volume Mction and surface area per unit volume. THE simplest kinds of measurements that may be made on a metallographic section are counting measurements. There are three such simple counting measurements, which are determined by sampling the microstructure with a point, a line, and an area. The first of these, the point count, is probably the most familiar among metallographers. The second count, the number of intersections a test line makes with particle outline, is somewhat more recent in its origin and application. The third counting measurement, the number of particle sections observed in unit area of the plane of polish, has long been used in the estimation of grain sizes. The real utility of these three counting measurements lies in the fact that they are rigorously and unambiguously related to certain extensive geometric properties of the three-dimensional structure of which the metallographic section is a sample. These relationships will be reviewed briefly below. Of somewhat secondary importance to the fundamental relationships is the observation that, if some simplifying assumptions about the geometry of the three-dimensional structure are introduced, manipulation of the counting measurements gives a more complete description of the structure. Specifically, in addition to the extensive properties which these measurements rigorously estimate, the number of particles, their size, and their shape may be determined. The purpose of the present paper is to explore the consequences of introducing the assumption of constant size and shape. A later paper will deal with the estimation of geometric properties of structures which may be characterized by a two-parameter size distribution. It should be mentioned that the introduction of this simplest of assumptions, while clearly not generally justified in metallurgical structures, is not without precedent. For example, many estimates of the number of particles per unit volume of structure, based upon a single counting measurement, are scattered throughout the literature.13 Virtually all of these developments assume a constant particle shape, e.g., spherical or polyhydral, and constant size. That such an assumption is necessary is evident from the fact that, for more general structures, more than a single parameter is required to describe the three-dimensional structure, so that the determination of a single parameter on a section would be insufficient to specify the structure. Similar developments for the estimation of particle size from a single counting measurement, e.g., routine grain-size determinations, make the same very limiting assumption,435 but have nonetheless proven of practical value. The present paper embodies a generalized approach to the development of relationships among the two-dimensional counting measurements and the three-dimensional geometry of the structure, subject to the assumption of constant particle size and shape. It is the hope of the author that by presenting the relationships and the assumptions involved in dealing with this approximation, in a single, unified treatment, the reader may be impressed with the usefulness of the counting measurements, may be guided in their application to the estimation of details of the geometry in specific structures in which he may be interested, and may be moved to apply the results, with understanding, to new structural problems. Several authors6, 7 have demonstrated independently that it is possible to obtain unbiased estimates

Jan 1, 1964

By P. Hazebroek, M. Prats, E. E. Allen

Well locations in water floods frequently do not coincide with the ideal well locations associated with the flood pattern which is used. A question of importance is. "How much oil is lost because of this?". This is the problem treated in this paper. It is assumed that each pattern in a five-spot flood has the proper number of production and injection wells but that the wells may be off-pattern. The distance by which a well is off-patern is given in terms of the pattern spacing, defined as the length of one side of a five-spot. The influence of off-pattern wells on the performance of a five-spot flood has been investigated mathematically for unit mobility ratio. All production and injection rates are assumed to remain equal. The loss in recovery resulting from pattern irregularitie: has been calculated at a cumulative water injection corresponding to a 98 per cent water-cut in a regular five-spot. Displacing a single production or injection well by about one-third the pattern distance reduces the total field recovery by 4.4/N per cent of the recovery obtainable with regular spacing, where N is the number of five-spots in the flood (assumed large). When off-pattern wells are separated by at least one regular five-spot and are displaced by less than one-third the pattern distance, the total loss in recovery in a large-scale flood is, at most, 1 per cent of the recovery obtainable from that field with a regular five-spot pattern. However, much higher losses may occur if the off-pattern wells are not separated by a regular five-spot, if the rates are imbalanced, or if the mobility of the injected water is higher than that of the crude. Although the loss in oil recovery due to pattern irregularity often may be low, the off-pattern case will always require injection of more water to reach the same final water-cut. The volume of water injected per unit volume of oil displaced has been calculated for each five-spot adjacent to a five-spot containing a single 08-pattern well. The cumulative water injection at the time of 98 per cent water-cut may be increased by as much as 37 per cent when a production well is displaced one-third the pattern distance toward an injection well. The existence of differences between actual subsurface locations and the idealized well patterns used in secondary recovery operations is well recognized. However, the methods commonly used for predicting waterflood behavior ignore such differences, even when subsurface locations are known. The reason for this is simple. The idealized well patterns are highly symmetrical and, as such, the production history of the pattern (and even of the field) can be determined from that of a few production wells—usually from only one. Consideration of the many irregular well spacings found in a specific field would entail a large amount of work, and then the results would be applicable only to that specific field. In an attempt to provide an answer to the more general problem, this paper considers a water flood having an idealized well pattern, except for one well which is not at its regular location. When several off-pattern wells are present, their contributions are assumed to be additive unless the off-pattern wells are close to each other. Only four positions of the off-center well (at x, y. of Fig. 1) are considered in this paper. These are shown

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.' A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be' used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

By Viswanadham B. V. S., Babu K. V

Many refineries are in the process of revamping and expanding their existing facilities. Most of the refineries are located in coastal areas due to ease of transportation and storage of crude oil. Considering the criticality of structures as well as prevailing soil conditions, most of the structures are supported on pile foundations. In depth review of sub-surface investigations data followed by liquefaction assessment of the site, it is noticed that site is prone to liquefaction during the seismic event. Among various techniques, driven cast-in-situ piles were selected to mitigate liquefaction. Static cone penetration tests were conducted during the pre and post installation of driven cast-in-situ piles at identified locations. Analysis of cone penetration test data shows that considerable ground improvement has been achieved post-installation of driven cast-in-situ piles.

Sep 1, 2022

By James J. Bean

HE task of measuring the specific gravity of the -*- operating medium in a heavy-media separation system has never presented a particularly difficult problem because the medium is fairly stable and the overflow of the separatory vessel, as well as its underflow, can be sampled easily and accurately and the specific gravity of the suspension determined easily by weighing a known volume. However, while this method is simple and accurate it does require the operator to take the sample by hand and to weigh it and there is considerable temptation to avoid the periodic sampling if everything seems to be going well, or if something is occupying the attention of the operator. Furthermore all operators do not sample in exactly the same manner and considerable practice is required for two operators to be able to "check" each other to the last few hundredths, particularly if the sample is cut underneath the drainage screen where location of the point of sampling and load on the screens tends to influence the determination. While none of the above presents much of a problem, we have all recognized that some mechanical method of continuous measurement and recording would be advantageous since the operator would merely have to glance at the meter to check the gravity and to have an indication of the trend of any changes. Also if the instrument were of the recording type, a permanent record would be available for the guidance of the superintendent. The Eagle-Picher Mining and Smelting Co. was the first heavy-media user to actually install such a recording meter. In 1946 they installed in their Central Mill at Cardin, Okla., a specific gravity recorder manufactured by the Bristol Co. of Water-bury, Conn. R. A. Barnes, of the Bristol Co., working with E. H. Crabtree, Jr. and Elmer Isern, of Eagle-Picher, made the application and worked out the problems of sampling and measuring. Their attempts to measure the specific gravity of the medium in the cone itself were not entirely successful and they resorted to an outside sample tube for actually making the determination. Because of the particular flowsheet used, it was possible to tap off from the medium return pipeline a stream of medium and divert it into the sampling tube, which was provided with a constant level overflow and a spigot underflow, and into which the bubbler tubes dipped. The Eagle-Picher installation was successful and its possibilities were recognized by the Mineral Dressing Laboratory of the American Cyanamid Co. It was decided to install a similar unit in the heavy-media pilot plant to investigate further its possibilities. Chief among these was the continuous record which it was felt would be proof of the steadiness of the gravity in a heavy-media cone, something which is not always appreciated by POtential users. Because the heavy-media pilot plant is required to operate at a wide range of specific gravities, it was realized that the unit would have to record all gravities from 1.25 to 3.50, and do it to the nearest 0.01. It would not be necessary to record all of this wide range on a single chart and the method selected was to have 4 bands, each band range overlapping the other a small amount and calibrated so that with standard charts one division would represent 0.01 sp gr. A shift from one band to another could be arranged without alteration of the instrument itself, being accomplished by a simple change in the bubble-tube lengths, as described later. Accordingly, a recording type instrument was purchased and installed. Because there were some advantages in doing so, the first installation attempted to measure the gravity of the cone proper by placing the bubble tubes in the cone. This was not at all satisfactory and the second scheme utilized a fixed vertical screen at the surface of the cone, and an external sample-tube arrangement. We were particularly anxious to make this work as we felt it would be advantageous to measure the top level of medium where the separation was actually being made, but we were doomed to disappointment because it was impossible to keep the screen clean of float. Since the top gravity of the cone is the most convenient place to sample for control, a launder about 2 in. wide was installed longitudinally beneath the

Jan 1, 1951