Search Documents

By Makarinskym F. M.

"This paper describes mechanical and operating modifications that were and are being made to current on-line flotation cells at Falconbridge Nickel Mines concentrators. Improved metallurgical performance and metal recoveries of some 3·4% over the past ten years are the end result of the modifications made. The paper acknowledges the contribution of operating, technical and maintenance personnel and the Company ""suggestion plan"" program. 1. INTRODUCTIONFalconbrirdge Nickel Mines Limited, incorporated in 1928 is a major product of nickel, copper,coba1t and other metals and minerals. The Canadian Nickel Division operating facilities in the Sudbury Area currently includes seven mines, two concentrators, and a smelter.For many years at all concentrators, improv0mcnts in metal recoveries have been continually under investigation. One area was to improve the flotation cell performance. This paper will deal with mechanical and operating modifications to the cells at the Strathcona and Falconhridge Ni-Cu sulphide concentrators, at the Sudbury Operations.One of the prime means to mineral beneficiation processing has been, and will continue to be, the basic froth flotation cell. The efficient operation of a flotation cell is the key to satisfactory metal selectivity and recovery. The essence of good design is simplicity. Changes to cell design can contribute to a significant improvement in metal recovery.Over the past 10 years, modifications to the flotation cells have contributed to an improvement of some 3-4” in mineral recovery. Providi11g tl1c initiative for improvements include operating, maintenance and technical personnel, as well as the employee suggestions submitted th1·ough the Suggestion Plan Program."

Jan 1, 1982

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By III Scotland

Genstar's underground mine at Texas, MD experienced a failure of the mine roof and subsequent damage to an underground backfill caused by surface floodwaters. A hydraulic backfilling program was developed in house to stabilize temporary repairs to the mine roof, replace 2300 yards of pneumatically stowed backfill, and complete a permanent repair to the mine roof. A flowable backfill material was developed, tested, and later marketed as the result of experience gained during this project. In addition, Genstar personnel developed backfilling techniques to meet the requirements of the repairs and completed work without the additional expense of non company services or contractors.

Jan 1, 1992

By Ulrich Maidl, Jamal Rostami, Ulf Gwildis

Tunnel Boring Machines (TBM) have more or less become the preferred method of tunneling in various ground conditions and Programmable Logic Controllers (PLC) or microprocessors are standard features on TBMs to monitor and record various sensory systems on the machine providing the possibility for machine automation and control. The data collected from these sensory systems and channeled through PLC is stored for real-time analysis or use by the operators. Based on typical construction specifications, part of the information collected in the process is shared with the project management team representing the owner. Machine data automatically acquired during TBM advance is typically processed by specialized software to offer the project team data visualization and evaluation options. Interfacing with Geographic Information System (GIS), Computer-Aided Design (CAD), 3-D geologic model, instrumentation data bases, and Document Management Systems (DMS) allows for developing Building Information Models (BIM) of the tunnel’s as-built condition. Application of Artificial Intelligence (AI) processes such as Machine Learning (ML) have already been used for analysis of data, including performance prediction of hard rock TBMs, and exhibited the potential of big data analytics in improving the productivity of the operations. This paper outlines anticipated disruptive technological advances with implications on geotechnical exploration, TBM operation, face condition tracking, subsurface risk allocation, and claims management in the future.

Jun 13, 2021

By Ivan R. Jankov

Nas plantas de sinterização, os sistemas de despoeiramento são comumente instalados para atender os quesitos de proteção ambiental. Estes equipamentos precisam ser modernizados periodicamente devido aos seguintes motivos principais: limites de emissão mais restritivos exigidos pelos órgãos ambientais, mudança do processo que implica na inclusão de novos pontos de despoeiramento, ineficiências de operação e manutenção dos equipamentos, falhas no projeto original do sistema de despoeiramento. Neste artigo, apresentaremos diversas soluções de retrofit/ revamping para exaustão primária da máquina de sinterização, bem como para despoeiramento de sistema de exaustão secundária e de pátio de matéria prima. As vantagens e desvantagens de cada solução serão analisadas utilizando-se experiência de projetos reais do grupo Hamon. Serão apresentadas também as últimas tendências tecnológicas que possibilitam controle de emissão de outros poluentes, tais como de SOx, de metais pesados e de dioxinas/ furanos.

Aug 16, 2017

By C Harwood

Underground coal mines in the United States are in the process of completing installations for tracking and communication systems, mandated by Congress after a number of recent coal mine disasters. Yet, evaluation, modelling and testing of such systems has lagged due to legislated changes, abruptly introduced into the coal mining industry. System installation in a wide array of mine types, configurations, layouts and characteristics has provided a wealth of information regarding their potential in underground environments. Data collected from numerous installations for a variety of systems can be used to further define true capability and accuracy of communication and tracking packages. This paper describes a uniform means of evaluating the performance of a communication and tracking system. Several performance measures are proposed and described. These measures can also be predicted using an interactive software program. This program predicts the signal propagation, given the input mine characteristics and layout, with numerical and visual feedback. New or alternative system installations can also be more accurately designed to potentially minimise initial system cost and time required for trial and error installs. The focus of this research is to develop tools and protocols that can evaluate and measure the effectiveness of installed underground communication and tracking systems.

Nov 22, 2011

By Walter S. Weeks

IN this paper the effect of natural ventilation pressures is considered a part of the mine resistance and it is shown that their effect on the mine resistance is not the same as the total natural ventilation pressure of the shafts if the mine has several levels. It is shown that increasing the fan pressure causes the division of the air to approach the condition that would obtain if there were no natural ventilation pressure present. It is shown that if an appreciable difference in pressure is maintained between the beginning and end of a group of splits, the value of the integrated effect of the natural ventilation pressures on the individual splits does not change substantially with moderate changes of this pressure. A method is outlined for determining the resistance factor of the mine and the value of the effect of natural ventilation with the fan operating; also a method for determining this factor when circulation is caused by natural ventilation alone. NATURAL VENTILATION PRESSURE Natural ventilation pressure (N.V.P.) is caused by the difference in weight of the air in two similar columns between two horizontal planes, and the difference in weight is caused principally by the difference in temperature of the two columns. The fan pressure causes some variation in density, but, since it is usually small and affects both columns, its effect is relatively unimportant. It has been suggested that "N.V.P." be called "stack effect"; but, since the term N.V.P. was used in a previous Institute paper,' applied in exactly the same manner, the term will be used. FRICTIONAL RESISTANCE The frictional resistance to flow in a mine without natural ventilation may be expressed as RQ2 where R is a constant for a given air density and Q is the rate of flow. This frictional resistance plus the effect of velocity changes will be called the F pressure (F.P.) and a curve of F.P. against Q, the F characteristic of the mine. If a pressure is applied to a mine by a fan, the air flow so adjusts itself that the drop in pressure through any path from entrance to exit of mine, due to frictional resistances and velocity changes, is the same as that in any other path. The mine resistance varies as the square of the quantity. The air distribution without N.V.P. will be called "normal." NATURAL VENTILATION PRESENT When N.V.P. is irregularly distributed in a mine, it is more convenient in analysis to consider the N.V.P. as a part of the duct resistance. If it is so considered the resistance no longer varies as the square of the quantity, and if N.V.P. exists between levels the distribution of the air is no longer normal. The total N.V.P. of the mine is the pressure caused by the full length of the shafts. If a mine has several levels, N.V.P. exists

Jan 1, 1944

By H. B. Northrup

Mineral Industries Extension instruction was pioneered by The Pennsylvania State Colleges Extension work was organized in 1893 and constituted what is believed to be the first vocational adult educational effort in that field in America. From 1894 to 1899, twenty-seven extension bulletins were printed and distributed free for the benefit of classes in the coal-mining industry and the records show that free lectures wore delivered by a corps of teachers of the mining department of the College "to the mining employees at their customary lace of assembly upon matters of interest to them in their occupation." In 1899, the State Legislature reduced the appropriation to the College and therefore the extension pamphlets and lectures were discontinued. Several sporadic attempts were made to resume the extension services in mining through industrial grants for travel and publications, and through voluntary contributions by members of the resident staff. The work. consisted mainly of lectures and demonstrations and served the purpose of creating the desire for more training and information of a more formal character. In 1928, the nave of the school was changed, by trustee action, from School of Mines and Metallurgy to the School of Mineral Industries and the working structure of the school was organized under the three functional collaborating headings: Resident Instruction, Correspondence and Extension Instruction, and Mineral Industries Research. The three functional bodies are separate, yet interdependent. The Federal Smith-Hughes law, passed in 1917, made Federal and State funds available for vocational educational work. Mining extension was revived in 1919 and the College employed one full-time extension professor to reorganize the work and instruct the classes. In 1923, the State Department of Mines and the State Department of Public Instruction entered into, a formal agreement with the School of Mineral Industries to assist the College in its extension program.. Classes were organized to study the State mining laws and State Department of Mines' previous examination questions and answers, in preparation for coming state examinations for certification of competency as underground officials. Mimeographed lesson material was used at first, and in 1947 and 1929 mining instruction and mining teacher-training lessons were printed. In 1931, the extension activities of the school were placed on an organized basis compatible with the newly formed school organization and a director was appointed to tale full charge of the work. During that year, at a conference in Harrisburg, an agreement was consummated between the State Departments of Public. Instruction, Mines, Labor and. Industry, and the College whereby extension classes in the field of the, mineral industries could be organized by the College, throughout the State, under "public supervision and. control," in close cooperation with the State Department.

Jan 1, 1941

By J. S. Osoba, J. G. Richardson, F. M. Perkins

Laboratory experiments have shown profound diffcrences in the behavior of so-called "fresh cores" from the East Texes field and of the same cores after ex~ractio~l with organic solvents. The residual oil satura/ion remaining after waterflooding fresh cores was appreciably lower than the corresponding saturations after flooding extracted cores. This behavior was also reflected in the water-oil relative permeability-saturatiorl relations, which were more favorable for high oil recovery from the fresh cores. These differences were evident not only in the amount of residual oil left after wafer flooding, but also in the saturation water remaining in the core after displacernent by oil. Residual water saturation after displacernetzt of water by oil was higher in the fresh cores than in the extracved core,. Capillary pressure-saturation relations were also different for the fresh crnd extracted cores. Imbibition experiments indicated that both fresh and extracted Bast Texas cores imbibed water spontarteOLISIY, but- the rate of imbibition of water was higher for samp1es after. extraction than it was for fresh core. material. INTRODUCTION Several years ago a series of waterflooding tests was made in the laboratory on a number of Woodbine core samples from the East Texas field. These samples had been stored in containers open to the air and were extracted with organic solvents before they were subjected to the laboratory tests. After water flooding, the residual saturation of kerosene, which was the oil used in the tests, was found to average about 30 per cent. This saturation was higher than expected. In investigating the circumstances which might have been responsible for such a high residual oil saturation, attention was given to possible changes in wetting properties of the rock brought about by the procedure employed in extracting the cores. Preliminary results indicated that the explanation for the high residual oil saturation lay in the wetting behavior of the cores, though what effect extraction had on this behavior was not clear. In consequence, the work described in this report was undertaken in an attempt to investigate the mechanism responsible, and to ascertain the actual residual oil saturation to be expected in the reservoir after water flooding. It was soon found that there were profound differcnces in the behavior of so-called "fresh cores" from the East Texas field and of the same cores after extraction with organic solvents. These differences were evident not only in the amount of residual oil left after water flooding, but also in the saturation of watet remaining in the core after displacement by oil. The complete explanation of this behavior is not yet apparent. The description of work and results described in following sections, therefore, must be considered as an interim report presenting facts which must await additional information before they can be fully interpreted.

Jan 1, 1956

By P. Raffinot, M. Rey, V. Formanek, G. Sitia

Six years of laboratory study, followed by three years of mill operation treating more than 10,000 tons of ore, have established the flotation of oxidized zinc ores with fatty amines as an efficient process. Recently the method has been applied with success to partially oxidized sulphide ores. In this paper the authors give an account of their research and the milling results obtained in Sardinia since 1951. CONCENTRATION of oxidized copper and lead ores by flotation has been practiced for 30 years, but flotation of oxidized zinc ores has remained unsolved until a few years ago. This problem is, however, of great importance in mining districts where large tonnages of oxidized zinc ores exist in underground mines or in dumps. Some sulphide ores also possess a degree of oxidation high enough to justify recovery of oxide zinc minerals. Various attempts have been made to float the zinc carbonate, smithsonite. It is well known' that smithsonite can be collected with fatty acids, but as the predominant gangue constituents, limestone and dolomite. are floatable with the same reagents, fatty acids are difficult to use. Gaudin has shown,' on mixture of pure minerals, that smithsonite can be floated with higher xanthates, or better, with higher mercaptans. Another procedure, briefly mentioned by Davis," consists in sulphidizing the ore, activating the zinc carbonate with copper sulphate, and floating with ordinary xanthates. This process was attempted in the writers' laboratory in 1946, but results were erratic. It has since been taken up by Italian engineers and is in operation on certain types of ores. Two other research projects should be mentioned. In 1942 Erlenmeyer and others' floated synthetic mixtures of smithsonite and gangue minerals with hydroxyquinoline, an analytical reagent for zinc. On the other hand, Bunge, Fine, and Legsdin published in 19465 Some interesting results obtained on Missouri oxidized zinc ores. With sodium oleate as a collector and a combination of sodium hydroxide, sodium silicate, and citric acid as a limestone depressor, they secured, after four cleaning operations, a good grade of concentrate. With many ores this reagent combination lacks adequate selectivity. In 1939 M. Rey initiated a program of research on this important problem. Work was pursued first at the School of Mines in Liége, Belgium"' and later in Paris in the laboratories of Société Miniére et Mbtallurgique de Penarroya and Société Minerais et Métaux. Reagents used in the beginning were higher xanthates and mercaptans, later fatty amines. Sulphidization with sodium sulphide was found necessary. These conditions make possible the flotation of zinc carbonate and zinc silicate. Two milling plants were put in operation in Sardinia in 1950 and several others are now contemplated." ' It should be mentioned that unknown to the present writers McKenna, Lessels, and Peterson were

Jan 1, 1955

By Ralph M. Hunter

UNTIL recent years, maintenance of surface coal handling facilities was a relatively simple task. Equipment consisted principally of conveyors, screens and crushers of comparatively simple construction. Electrical equipment consisted of motors and starters, with little, if any, interlocking. In most cases failure of any component affected only the grades of coal loaded so that even a prolonged break-down did not affect mine operation materially. However, with the introduction of modern cleaning plants, the picture has changed. The equipment is much more complex and therefore more difficult to maintain. In many cases failure of any component of the plant prevents loading of coal. Even if provision is made to by-pass, the quality of coal loaded is lowered, affecting markets. In the case of plants designed to permit full seam mining, marketable coal cannot be loaded without operation of the cleaning plant. Under these conditions it is apparent that considerable thought and effort toward better maintenance are justified. In order to assure continuous, efficient and economical operation, maintenance should receive consideration, not only after the plant is in operation, but while it is being designed. It is hardly necessary to say that the designer should strive for sturdiness and wearing qualities. It is sometimes not realized, however, that even the best parts will sooner or later require replacement or repair. The designer should, therefore, give consideration to accessibility. Anyone who has had to do with cleaning plant maintenance is familiar with installations where several hours are required to get at a part that can be repaired or replaced in a few minutes, once it is accessible. As in most cases, experience is the best guide. The men who operate and maintain this equipment know the problems encountered. Whenever available, the opinions of these men should be sought and heeded. As an example, we might consider the refuse elevator on a Chance Cone. Our company is now operating three of these cones, the first of which was installed in 1941, and the latest in 2946. Exact records are not available, but well over 50 pct of delays charged to the Chance Cones have been caused by the refuse elevator. This elevator receives refuse from the cone and carries it to a point above the water level of the cone, discharging onto a dewatering and desanding screen. Since the elevator operates under water and necessarily has close clearances in the lower boot, it tends to jam on large pieces of refuse or tramp iron. The chain, buckets and boot are also subjected to the action of water, sand and refuse, which accelerate normal wear. In case of jamming or chain-breakage it is necessary to drain the elevator and the cone so that even a minor fault in the elevator causes a considerable loss of time for the cone. In our new plant, which will contain two Chance Cones, the refuse elevator has been eliminated. This was accomplished by raising the cone so that the refuse gates could discharge directly onto the dewater-

Jan 1, 1948

By Benson R. P

Building a new tunnel to accommodate CN North America's needs or double stacked container traffic for the next 100 years represents new and unprecedented challenges. Innovative approaches to contracting, especially the Negotiated Compressed Process (NCP), TBM design, project management, and the regulatory and approval process, were all required to deliver a new tunnel to meet the needs of CN North America within the approved completion schedule of 33 months compared to a traditional approach of 45 to 48 months. The NCP resulted in trimming a full 12 months from the project schedule with an anticipated saving of direct and indirect costs.

Jan 1, 1993

By R. S. Archibald

The subject of this paper is particularly appropriate, since Daniel C. Jackling was active in early exploitation of taconites on the Mesabi Range and contributed greatly to their later economic development. After his success in developing the low grade porphyries in the West he looked for more worlds to conquer, and so undertook the concentration of low grade taconites, from which he hoped to produce commercial ore. Mesabi Iron Co., organized in 1919, actually did produce merchantable sinter from taconites in 1922. The enterprise did not prove commercial at the time, as cost of production was high and the surplus of iron ore in the Lake Superior District already contributed to a low market price, but this same property has since been developed by Reserve Mining Co. The work done by Jackling had much to do with the success of this later venture. Iron ore was first discovered on the Marquette Range in Michigan in 1845. The first ore from this range came from the old Jackson mine in Negaunee in 1848. During these early years this property and others on the Marquette produced limited tonnages for transportation to Lower Lakes and for consumption by charcoal furnaces in the area, where a plentiful supply of hardwoods furnished the charcoal for iron smelting. The Marquette and other ranges tributary to Lake Superior did not produce much ore for transportation to Lower Lakes until the locks at Sault Ste. Marie were constructed, but from the time the first lock at the "Soo" was completed in 1855 these ores were transported through the locks to consumer centers in the East. The Marquette Range has a history of continuous production from 1848 to the present day. In 1877 the Menominee Range was discovered at the location of the old Penn Mines near Vulcan, Mich. There were further discoveries of ore on the old Menominee Range and at Florence, Wis., in 1880 and at Iron River and Crystal Falls, Mich., in 1882. Penn Mines continued in operation from the date of their discovery until they were finally exhausted by Pickands-Mather in 1945, but operations still continue on the Menominee in the Crystal Falls and Iron River districts. Ore is shipped to a lake port at Escanaba, Mich.

Jan 1, 1960

By Persifor Frazer

The following notes on the Whopper and adjoining mines in the Gunnison district of Colorado mere made in the spring of this year. The time chosen for the author to visit the region was, unfortunately, the most unfavorable of an exceptionably unfavorable year. About the middle of May all the hill slopes, which at this period of the pear are generally covered with pasture, were thickly covered with snow. The unusually large precipitation of this Tear caused loacal mountain torrents at every few hundred feet, which wore away the oft foothills into gulches, gouged great chasms out of the roads, and transformed miles of usually dry soil into dangerous quagmires. Travel was totally interrupted for weeks, except on horseback or afoot, and even then with great difficulty and some danger. The Whopper mine is situated on the Whopper Mountain, about two miles from the headwaters of Rock Creek, and on the right hank of that stream. The Whopper Creek flows into Rock Creek horn the east, and, by a precipitous descent, offers excellent facilities for its utilization as a source of power. This stream, which pours past the picturesque Whopper Cabin about thirty tons of water a minute, has a fall of 100 feet in 400 yards, and is said to be a stream of some size, even at the seasons of the year when drought prevails. The Whopper claim extends down the hill a distance of about 250 feet to its intersection with the Whopper Creek (on the other side of which is a small tunnel on its extension called the "Teller") and over the steep hill northwest to the limits of the claim about 1250 feet. The part of the mountain in which this mine is situated is remarkable for its splendid forest, the spruce, fir, and quaking asp covering the mountain-sides with a green growth of valuable timber. The distance from Gothic City to this mine is about eight miles along the valleys of East River and Rock Creek, and on the divide which separates them. The elevation of Gothic City is given from the engineer's notes as 9500 feet above sea-level, and the mean of several observations with a Beck watch-barometer made the elevation of Whopper Cabin (which is about fifteen feet above the floor of the Whopper upper tunnel) about 1260 feet above Skiles's Cabin in Gothic City. The record of this instrument must, how-

Jan 1, 1881

By David E. Hyatt, Christopher H. Cox, Franklin T. Davis

INTRODUCTION The composition of water used in the flotation process has always been of primary interest to the flotation metallurgist. It is by alteration of the chemistry of the water introduced to the process that flotation separation is effected. In only a few cases has it been necessary to treat available water prior to use in the process. In the past, flotation tailings were treated for the removal of solids via the tailings dam and water decanted from the dam was either recirculated to the process or discharged to the surface water system. The choice of recirculation or discharge was based upon water availability, effect of recycle water on the process, and economic considerations. The Federal Water Pollution Control Act Amendments of 1972 have charged the United States Environmental Protection Agency with establishing effluent limitations from point sources of discharge into the navigable water of the United States. A detailed study, sponsored by EPA, of the water of ore processing plants took place in 1974 and 1975 and guidelines for these plants will presumably have been published by the time this paper has been presented(1). The action of many of the individual states preceded the EPA in this attempt to regulate the quality of the water discharged from industrial point sources. Even with recycle of tailings water, some water is discharged from tailings dams into the substrata and at least one state is currently preparing guidelines for the quality of water discharged into the substrata.

Jan 1, 1976

By A. J. Shaler, J. Prieto Isaza, J. Wulff

Tantalum metal has a number of unique properties which give it widespread application in modern technology and in research. In electronic apparatus involwing high temperatures in vacuo some of the refractory metals 6ecome brittle. Tantalum retains its ductility at elevated temperatures, and this property, together with its low vapor pressure and its ability to absorb gases, make it important in this field. Its chemical inertness in the presence of acids, halogens, and other corrosive media, makes it useful in chemical apparatus and in neuro and orthopedic surgical applications. As an addition to tungsten carbide in steel-cutting grades of cemented-carbide tools, the carbides of tantalum and of its sister element colum-bium have found considerable use. The present-day method1 of manufacturing tantalum is to sinter a powder compact of the metal in vacuo. Because tantalum-columbium alloys are difficult to work and since tantalum ores almost always contain columbium, the two metals must be separated chemically, the products of the separation being generally in the form of potassium tantalum fluoride and potassium columbium oxyfluoride. These salts are used in fused-salt electrolytic baths from which coarse metallic powder is deposited as a sponge at the cathode. Finer powder can be made from the coarse product or from tantalum scrap by first submitting it to an embrittling heat treatment in hydrogen and then crushing it. The fine hydrogen-containing powder may subsequently be degassed in vacuo at a high temperature. Prompted by the success of others2,3 in the magnesium reduction of titanium and zirconium halides; one of the authors undertook4 an investigation of the thermochemistry of the reaction between solid magnesium and gaseous tantalum penta-chloride, a subject which had not previously been studied. He found that the heat of formation of tantalum pentachloride is approximately 364,250 cal per mol at temperatures lower than the melting point of magnesium. A value of 83 units was found for the standard entropy at these temperatures. With these values, it was shown that magnesium and tantalum pentachloride are capable of reacting exo-thermically at temperatures less than the melting point of magnesium, and that no great violence is to be expected when these substances are heated together. The exothermic nature of the reaction indicated that the Drocess should be efficient and should not require much externally applied energy. Tantalum pentachloride is not commonly made commercially, and any process using it therefore involves the subsidiary problem of producing and handling this substance. A series of experiments was carried out in which dried chlorine saturated with carbon tetrachloride was passed over heated tanta-

Jan 1, 1949

By Persifor Frazer

THE following notes on the Whopper and adjoining mines in the Gunnison district of Colorado were made in the spring of this year. The time chosen for the author to visit the region was, unfortunately, the most unfavorable of an exceptionably unfavorable year. About the middle of May all the hill slopes, which at this period of the year are generally covered with pasture, were thickly covered with snow. The unusually large precipitation of this year caused local mountain torrents at every few hundred feet, which wore away the soft foothills into gulches, gouged great chasms out of the roads, and transformed miles of usually dry soil into dangerous quagmires. Travel was totally interrupted for weeks, except on horseback or afoot, and even then with great difficulty and some danger. The Whopper mine is situated on the Whopper Mountain, about two miles from the headwaters of Rock Creek, and on the right bank of that stream. The Whopper Creek flows into Rock Creek from the east, and, by a precipitous descent, offers excellent facilities for its utilization as a source of power. This stream, which pours past the picturesque Whopper Cabin .about thirty tons of water a minute, has a fall of 100 feet in 400 yards, and is said to be a stream of some size, even at the seasons of the year when-drought prevails. The Whopper claim extends down the bill a distance of about 250 feet to its intersection with the Whopper Creek (on the other side of which is a small tunnel on its extension called the "Teller ") and over the steep hill northwest to the limits of the claim about 1250 feet. The part of the mountain in which this mine is situated is remarkable for its splendid forest, the spruce, fir, and quaking asp covering the mountain-sides with a green growth of valuable timber. The distance from Gothic City to this mine is about eight miles along the valleys of East River and Rock Creek, and on the divide which separates them. The elevation of Gothic City is given from the engineer's notes as 9500 feet above sea-level, and the mean of several observations with a Beck watch-barometer made the elevation of Whopper Cabin (which is about fifteen feet above the floor of the Whopper upper tunnel) about 1250 feet above Skiles's Cabin in Gothic City. The record of this instrument must, how-

Jan 1, 1881

By E. H. Crabtree, T. C. King

THE ferrosilicon grinding unit at the Central Mill of the Eagle-Picher Mining & Smelting Co. near Picher, Okla., was completed in March 1947. The object of the plant was to grind pigs of ferrosilicon, having a size of approximately 1 ½ by 4 by 12 in. and an analysis of 85 pct Fe and 15 pct Si, to approximately 100 mesh by crushing and wet grinding in a ball-mill classifier circuit. The minus-loo mesh ferrosilicon had formerly been purchased, and was used as medium in the heavy media process for treatment of lead-zinc ores. From the standpoint of dollars and cents, the cost of minus-100 mesh ferrosilicon was roughly $40.00 per ton more than pigs of the corresponding alloy delivered to the mill. Estimated wet grinding costs were considerably below this figure. The possible saving in cost of make-up medium for the cone plant was particularly attractive since, at that time, the plant losses averaged over four tons of minus-100 mesh ferrosilicon per day. Aside from the probable saving on the grinding charge, the need for such a unit was twofold. First, periodic fluctuations in the differential between the top and bottom densities of the cone were thought to be detrimental to metallurgy. There was little doubt that an intermediate differential existed at which the heavy media separation was most efficient, representing a compromise between concentrate grade and tailing loss. Furthermore, if a finer, but considerably cleaner, medium could be obtained, there was the possibility that the differential could be decreased without increasing the viscosity, or conversely, the viscosity of the medium decreased without increasing the differential. Preliminary to experimental work aimed at pegging the cone differential and circulating medium viscosity at whatever values were found to be most efficient, it was essential to have control over both the non-magnetic content of the medium and the particle size of the contained ferrosilicon. The latter was possible by means of a grinding unit at the mill. Second, whereas the ferrosilicon alloys are made by a number of manufacturers, only two, to our knowledge, grind it in any quantity for use in heavy media plants. For all practical purposes, the Central Mill was limited to one source of supply, a particularly vulnerable position. In case the supply was cut off, it was thought that pigs of the 85 pct Fe, 15 pct Si alloy could be obtained elsewhere, providing means of grinding them was available. There was no published information available covering wet grinding of ferrosilicon. Dry grinding in batch mills and in continuous mills with air classification was being practiced, but the cost of grinding was excessive and the dust condition objectionable. It appeared that primary and secondary crushing was no particular problem, providing heavy duty equipment was used;

Jan 1, 1947

By R. C. Patterson

In view of the circumstance that very few important changes have been made within the last 15 or 20 years in the equipment of rod and wire mills, the description of a new process introduced by Grenville Mellen, of LleweIIyn Park, N. J., to take the place of the present laborious system of producing rods of lead, zinc, brass, copper, aluminum, etc., may be interesting to members of the Institute. This new process consists in the production of cast rods at one operation in a small continuous casting machine. The hot liquid metal is transferred from the melting crucibles directly into an endless chain of mold blocks in the machine, where solidification takes place, and the rod comes out continuously in a solid form at one end as long as the molten metal is supplied. The operation of these mold blocks so as to produce a solid rod of uniform structure constitutes an important part of Mr. Mellen's invention. The machine (Figs. 1 and 2), 12 ft. in height over all, 2 by 3 ft. in horizontal cross-sectional area, and 6,000 Ib. in weight, has a framework of cast iron, holding in position two endless chains of mold blocks, which are made in sections and join in center alignment. The mold orifice is made up of these mold sections, into which the liquid metal flows. The molding chains are composed of steel blocks, grooved on one face to form the molding cavity, and linked together with flexible joints. Each block is carried on four rollers which guide the chain around the end sprockets and carry it in its course through the machine. The accuracy of alignment requisite to the production of a perfect rod in the mold groove formed by these sections is secured by careful machine work, and by building the four ways, down which the alignment takes place, so that two of the sides are fixed permanently, whiIe the opposite sides are held to their position by spring pressure. The guides carrying the molds, while in casting position, are water-cooled square tubes. The length of this machine is somewhat indeterminate. A certain amount of both time and cooling surface is required to solidify the metal jn the mold; and one may either use a long molding chain and run it fast, or a shorter chain and run it correspondingly slower. We have found,

Jan 1, 1916

By O. P. Chisholm

The most noticeable change in lead smelting over the past few years has been the increase in the smelting rate of lead blast furnaces. For several years a great deal of attention has been paid to the preparation of the blast-furnace sinter charge but more recently the plan has been to incorporate- almost the entire makeup of the blast-furnace charge, excepting coke and scrap iron, at the sintering machines. Formerly, sintering machines were used primarily for removing, sulphur and for agglomerating finely divided material both sulphide and oxide in character. Limestone flux usually was so proportioned that a relatively large amount was added to the furnace charge direct. This procedure was also followed with oxidized ores, which were purposely crushed coarse' so that they would be adaptable for direct smelting on the furnace charge. In later years it has been the tendency in western smelters to include practically all of the limestone and oxidized ores in the sinter charge. This has been somewhat more costly because fine crushing is required for sintering purposes and because these oxidized materials were given additional processing through the sinter plant. The addition of such oxidized materials to the usual charge to be sintered, brought about, in certain instances, a deficiency in heat ordinarily supplied by the sulphide constituents of the charge. This heat deficiency has been remedied by the addition of carbonaceous fuel, in the form of finely crushed coke breeze, or in a few instances by the addition of zinc retort-plant residues. The enhanced gold price has stimulated the mining of crude siliceous ores throughout the Western States and in the smelting of such ores more limestone is required for fluxing. Shipments of gold-bearing pyritic concentrates to Western smelters have increased, and the combination of increased silica, limestone and pyrite has increased the percentage of slag, which, in itself, is an aid in .securing smoother and more rapid smelting in the blast furnace. By the addition of these substances, the percentage of zinc in the slag has been appreciably lowered. at many plants, with resultant benefit to smelting speed at the blast furnace. This increase in slag formation with lowered zinc content has caused also perceptible lessening of the amount of lead on the charge and this has benefited the blast-furnace smelting. Although a satisfactory sinter is fundamental in increased rate of bullion production per furnace, there has been a trend over the list four or five years to decrease the percentage of coke and increase the percentage of scrap iron and limestone on the blast-furnace charge. As a result of these changes in practice certain blast furnaces, without any mechanical change, have doubled or tripled their tonnages. For furnaces whore the volume of air is recorded, records show decidedly larger air volumes with a comparatively small increase in air, pressure, or, none at all.

Jan 1, 1941