Search Documents

By R. Tanaskovic

The objective of study of climatic conditions in underground mines is to create a working environment suitable for normal development of operations. Disregarding the fact that the development of equipment and technology, especially during the past decade, made the work in underground mines much easier, it is observed, according to the number of professional publications, that increasing attention is devoted to the study of climatic operating conditions in mines of many countries. This indicates that the climatic operating conditions are closely connected with productivity, and in turn with mine production profitability, in addition to the protection of manpower health and working capabilities. Usually, the concept of unfavourable climatic conditions of operation implies increased mine air temperature and humidity and low air flow rate, resulting in impeded heat exhange between human organism and working environment. As known, above phenomena are present in deep underground mines where the heat problem exceeds the-problems related to other features of natural conditions of mining. On the contrary, unsuitability of climatic operating conditions in mines with shallower mining depths is manifested by inadequate heat, particularly during the cold winter period. The two stated aspects of unsuitable climatic operating conditions are not solvable only by mine ventilation, so the former case requires cooling and the later one heating of the air used to ventilate the pit, or part there of where the phenomena are manifested. Study of climatic operating conditions in mines is, due to the number of factors involved, a complex and time consuming task, and this was, among others, one of the reasons for inadequate study of these problems in many mines. However, it is evident that further development of mine production imposes the need to make the climatic operating conditions in mines similar to those existing in other activities, where increasing attention is being devoted to the improvement of these conditions. Development of mining industry in Yugoslavia, particularly over the past decades, caused several of our mines to approach mining depths where the heat regime has a major influence on climatic operating conditions. This imposed the need to determine and investigate heat regime parameters, especially those that cause unsuitable operating conditions. The results of such investigations in the case of the deep part of Lead and Zinc Mine "Trepca" - Stari Trg are briefly reported in this paper.

Jan 1, 1980

By Jim Salley, Mohammad Saleem, Indra Banerjee, Kevin Sapp

"On underground construction projects, effective Quality Management is essential for ensuring facility durability, life cycle performance and low maintainability. Furthermore, follow on contracts also rely on an effective quality management system for interface congruency. An effective Quality Management System (QMS) is also essential in mitigating risks and meeting schedule and budget performance objectives. For the past 15 years Central Puget Sound Regional Transit Authority’s Link Light Rail extension has successfully completed over 10 miles of twin bore tunneling and associated underground features including cross passages, deep sump structures and shafts. After the completion of each segment, lessons learned have successfully been implemented to improve the quality of delivered projects. This paper presents the Sound Transit QMS with regard to a number of project elements of tunnel construction projects, with specific focus on quality performance of slurry wall construction, TBM tunnel excavation assessment, segment production and segmental lining installation, and other associated construction features. A collaborated total QMS will be presented in this paper that will serve as a guide for successful implementation of Quality Assurance and Quality Control processes. INTRODUCTION Implementation of a robust Quality Management System reduces defects, errors and omissions, identifies and addresses nonconformance in a timely manner and increases stakeholder confidence in the project. In fact and effective QMS helps ensure that optimal project outcomes are realized both in terms of project delivery and life cycle performance. The two key components of QMS are quality control and quality assurance. Quality Control (QC) is the procedure implemented to achieve a certain level of quality and ensure that products, processes and services meet specific requirements. Quality Assurance (QA) activities are carried out to evaluate the effectiveness of the quality control measures and ensure that the QC process is working. A team obligation that recognizes that quality is built into every aspect of a project is the basic concept of a successful QMS."

Jan 1, 2016

By S. W. Beckman, L. Williams, A. E. Seep, R. Fischer, J. Hubbard

Introduction The Summitville Mine located in southwestern Colorado was added to the National Priorities List in June of 1994. Summitville was the site of mining operations that began in 1873 with the discovery and development of gold placer and lode deposits in the late 1800's. The mine site is located about 25 miles south of Del Norte, Colorado in the San Juan Mountains adjacent to the Rio Grande National Forest at an approximate altitude of 11,600 feet. The site was mined for gold, silver and copper between 1873 and 1947. The Summitville Consolidated Mining Corporation, Inc. (SCMCI), a wholly-owned subsidiary of Galactic Resources, Ltd of Vancouver, Canada ran a large tonnage open-pit mine and cyanide heap leach operation from 1986 to 1992 (Pendleton and Posey, 1992) During the mine operation by SCMCI, approximately 10 million tons of gold ore was mined, crushed and stacked on a lined leach pad. Heap leach operations experienced water balance and unplanned solution discharges from the start of the mine life. Despite the production of 249,000 troy ounces of gold during the mine operation, SCMCI was unable to meet remedial requirements and notified the state of Colorado of its intention to file a Chapter VII bankruptcy in December 1992. The EPA Region VIII Emergency Response Branch took over site operations on December 16, 1992 to prevent a catastrophic release of hazardous substances to the environment. The multiple contamination sources at the mine site are due to both historic and SCMCI mining operations. Emergency response operations at the site have prevented releases of severely contaminated solution and a permanent treatment for all waste units at the site is under investigation. A Request for Proposal (RFP) was issued in October 1993 by Environmental Chemical Corporation (ECC) at the Request of EPA Region VIII, Department of the Interior and Bureau of Reclamation. The RFP requested that interested companies provide information on their ability to implement innovative treatment technologies to improve treatment efficiency and reduce treatment costs for remediation of the heap leach pad (HLP) spent ore and ore leachate solutions. Dames & Moore and Pintail Systems, Inc. (PSI) jointly submitted a proposal suggesting application of biotreatment processes for detoxification of cyanide in spent ore and HLP leachate solutions. The proposal was accepted for pilot and field demonstration under the SPA Superfund Innovative Technology Demonstration Program (SITE) with additional funding from EPA Region VIII. This report discusses the test program and results of a Focused Feasibility Study which demonstrated biotreatment processes for spent ore cyanide detoxification.

Jan 1, 1995

By K. Bragg

During the last several years considerable discussion has taken place on the long term aspects of uranium tailings management. These discussions have centered around a variety of topics which in turn lead to a variety of opinions. In order to come to grips with the various differences of opinion and points of view, the Atomic Energy Control Board has decided to prepare, as an interim measure, a list of proposed close-out criteria for uranium tailings management facilities. It is important to keep in mind that the criteria set out in this paper are proposals and are intended to initiate a continuing dialogue between the uranium mining industry and the various regulatory and government agencies. It is envisaged that this dialogue would continue for a period of from six to twelve months after which some final form of these criteria would be issued and applied to the active uranium mining facilities. In attempting to understand the reasons why the Atomic Energy Control Board has decided to propose these criteria now instead of at some future point in time, it is necessary to look at a number of existing facts. One of the most important of these is that something in excess of one hundred million tonnes of tailings currently are placed in various tailings management facilities. Furthermore, the rate at which tailings are being deposited into such management facilities is on the increase and this increase is expected to continue over the next five to ten years. The management of these tailings is currently covered under the Mine Facility Operating Licences issued by the AECB. Implied within these licences and supporting documents leading to them, are requirements for the conceptual approach to be used at abandonment. There is however, no current requirement for a detailed study on the engineering or financial aspects of such abandonment procedures. This is a gap which the Board feels must be addressed. There are, at this time, various initiatives underway both in Canada and within the international community which are attempting to address the problems and concerns of the very long term management of tailings. For example, current research in Canada which is composed of two components, one by the AECB dealing with purely regulatory aspects and a second major coordinated program under the direction of the Department of Energy, Mines and Resources and in particular by CANMET is going to deal with the technical problems. On the international scene

Jan 1, 1980

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the 'furnace free' conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By A. Karim, T. G. Langdon, C. Y. Cheng, J. E. Dorn

The effect of changes in temperature and stress on the creep behavior of Fe-4 pct Si was investigated over the temperature range from 650° to 1175K Over the temperature range of 799° to 110l°K, the shear strain rate, ?', obeys the relationship: where K is a constant, 7 the applied shear stress, G the shear modulus, g the free activation energy for diflusion, R the gas constant, and T the absolute temperature. The results strongly suggest that the creep in this alloy is controlled by a dislocation climb mechanism. In a recent investigation, Ishida, Cheng, and Dorn1 observed that the apparent activation energy for creep of a! Fe from 480" to 775°K corresponded to that for self-diffusion. Over the magnetic transformation range (775" to 1045"K), the apparent activation energy for creep increased steeply with increasing temperature in agreement with the known decrease in the free activation energy for self-diffusion. Passing through the Curie temperature, the apparent activation energy decreased abruptly following which it then increased mildly as the temperature further increased. Inasmuch as the apparent activation energy for creep of a! Fe below the Curie transformation range of temperatures appeared to decrease with increasing values of the stress, the data were analyzed in terms of a model based on the nonconservative motion of jogged screw dislocations. But since the observed creep rate was much higher than that which could be accounted for on the basis of usual models, the authors found it necessary to assume that pipe diffusion became significant over the lower temperature range. Furthermore, the abnormally high activation energy for creep above the Curie temperature was attributed to grain boundary migration which became prevalent in this temperature range. It was thought that a number of the interesting issues that arose in the creep of a Fe might be resolved by investigating the creep of Fe-4 pct Si alloy: This alloy has about the same Curie range and therefore should give creep results that closely parallel those for a Fe and in this way provide comparable data for analysis of creep mechanisms. Furthermore, it can be annealed at higher temperatures which could provide some stabilization against grain boundary migration. In addition, it might serve to illustrate the possible effects of short-range ordering on creep.

Jan 1, 1969

By James B. Graham, Earle E. Smith

The value of all minerals produced in the United States for the years 1930 to 1932 averaged $3,460,000,000 annually, according to Bureau of Mines reports. Of this amount, approximately $1,280,000,000 represents nonmetallic substances, such as petroleum, gas, sulfur and salt produced as fluids. Thus, about.37 per cent of the country's mineral wealth is procured through wells drilled in the earth, which require casing to keep them open throughout their life. Deep well drilling has increased greatly in the last few years. Several strings of casing have been set deeper than 9000 ft.—one, a string of 7?-in. O.D. casing, 10,301 ft. long, run in a well drilled by the Gulf Production Co. in West Texas, holds the record up to this time. These are longer strings than were contemplated when the American Petroleum Institute Specifications were adopted 10 years ago, therefore it is necessary to consider whether the present joint standards are adequate for such strings, or for even longer strings that may be called for in the future. Petroleum engineers are asking: Is there a possibility that stronger joints can be designed without going to stronger and more costly steels than offered in present specifications? Without sacrificing too greatly the tensile properties of the joint, can its design be changed to allow more clearance in the open hole below the next larger string of casing, and thus avoid costly underreaming? What can manufacturers offer for drilling through heaving shale? Fundamentals of the Problem During the last few years considerable study has been given to casing joints and their limitations, and since attention must be given to this subject by those who will be required to drill deeper holes, it is timely to review the fundamentals of the problem. These will be recognized generally as the following: 1. No threaded joint can be stronger than the area of metal under the root of the first perfect thread, and this area must be large enough

Jan 1, 1935

By O. U. Bradley

The utilization of casing-head gas in the manufacture of casing-head gasoline by both the absorption and the compression method is a most important factor in the conservation of our natural resources. Any industry connected with the oil business, in general, possesses particular attraction for a large number of people not conversant with its basic principles, for the reason that the large fortunes made in the production and utilization of petroleum and its products have been given undue prominence. The general impression of the public that enormous profits are to be realized in the casing-head gas industry with minimum expenditures of both capital and effort has, in a large measure, accounted for the phenomenal expansion of the industry in recent years and, likewise, has resulted in many mistakes and loss of investment funds. It is true that many installations have been very profitable, but such instances are always the result of careful planning, experienced judgment and conservative estimates. The inception and subsequent activity in the manufacture of casing-head gasoline, enabling the business to assume an important position in the petroleum industry, are of comparatively recent origin, as its greatest growth, particularly in Oklahoma, occurred during the years 1917 and 1918. Much information must yet be secured and systematized concerning the methods of manufacture of gasoline from high-yield casing-head gas, and a large field is still open for the application of accumulated experience and good engineering practice in devising better methods of extracting gasoline from casing-head gas of the poorer grades. The absorption process is coming into general use as a most efficient system of treating casing-head gas, and even so-called dry gas. In fact, there is a decided tendency toward the universal adoption of the absorption process as against compression methods. However, a general discussion of the relative merits of these two systems is not, within the scope of this article. A few of the facts that must be given 'consideration in arriving at a fair and impartial estimate of the actual investment value of the casing-head gas business are the quantity of gas available, the quality and

Jan 1, 1921

By J. C. Uy, A. A. Burr

A quantitative relationship between the allotropic phase boundaries of zirconium-base binary systenzs and the solute metallic valence is shown through an intermediate thermodynamic parameter. A simplified equation relating this parameter to the phase boundaries is briefly reviewed, and data from the literature are used to show the relationship of this parameter to the solute metallic valence. It has been reported that the solute metallic valence can be used as an index of phase stabilization in zirconium-base binary alloys.' It was shown that the algebraic sign of the slopes of the hcp/bcc phase boundaries of zirconium alloys correspond to the algebraic sign of the metallic valence of zirconium minus the metallic valence of the solute, or, in other words, a solute whose metallic valence is higher than that of the solvent tends to stabilize the high-temperature phase while one whose metallic valence is lower than that of the solvent tends to stabilize the low-temperature phase. Further analysis of the zirconium binary systems has revealed a quantitative relationship between the solute metallic valence and the relative slopes of the two-phase allotropic boundaries. This relationship involves a thermodynamic quantity whose significance can be seen in the following section. PHASE-STABILIZATION PARAMETER Let Qb be the difference between the partial molar heats of mixing of a given solute in the two allotropic phases of the solvent which are in equilibrium with each other at a given temperature, thus A relationship between this term Qb and allotropic phase boundaries has been employed by several au-thors'-= in the evaluation of phase diagrams, and can be briefly derived as follows. Referring to Fig. 1, consider the general case of two allotropic phases, each having a small mole fraction (Xa,Xb) of the solute, in equilibrium at temperature T and atmospheric pressure as represented by the reaction. solute in ß phase =solute in a phase If now a reaction occurs such that an infinitesimal amount of the solute is removed from the ß phase and added to the a phase, there would be a partial molar

Jan 1, 1967

By C Kocsis, G Baiden, Y Bissiri

CANMET-MMSL and Penguin Automation Systems Inc have been exploring how process simulation and ventilation modelling software, when combined, can be used to optimise hard-rock/metal mine ventilation systems. In combination, it is anticipated that this methodology will facilitate the exploration of mine design options that affect ventilation requirements and ultimately cost. Such integrated mine design could limit, and possibly reverse, the drivers that under current practices would generally dictate increased ventilation, power consumption, cost and greenhouse gas emissions. It is believed that the mining industry needs such process models to develop better business cases. For example, the implementation of optimised ventilation systems will undoubtedly require significant investment and mines are often reluctant to try such conservational measures unless they can be proven cost-effective. In general, Canadian hard-rock mines know their ventilation systems are providing too much air and consuming power unnecessarily. This is because their systems are designed to provide maximum production flexibility, based upon peak demand, which may be at some future time, and operated continuously at that level regardless of actual need. Simplistic analyses have shown electrical energy savings can range from 30 per cent through to 90 per cent (Hardcastle, Gangal and Leung, 1998). These savings depend upon such factors as the intensity and continuity of the production schedule as opposed to non-productive time. Where these savings occur is also important, if limited to either the primary or auxiliary ventilation systems, they could be negligible in a mineÆs total energy consumption. The problem these mines face is determining what level of ventilation is required in real-time and then the relative benefits. Such parameters as varying electricity costs, heating fuel options, different design criteria and their complex inter-relationship can effect the selection of an optimal system, depending on whether energy, environment or cost is the prime driver. The use of process simulators in underground mining is in its infancy; to date they have been used to show the benefits over the life of a mine under different mining methods, such as a comparison of tele-remote mining from surface against conventional manned operation (Baiden, 2000). This ongoing development advances the use of such simulators into a new and potentially important area, namely modelling the life-cycle ventilation requirements of a mine. This paper shows how such a life-cycle analysis as opposed to peak demand can provide the basis for optimising the design of ventilation systems and their control.

Jan 1, 2005

By H. T. Morris

ONE of the chief concerns of the Bethlehem Steel Co. naturally is the proper functioning of its organization. This involves the training of a continuous supply of younger men to fill the vacancies caused not only by the inevitable departure of older men, but also by the growth of existing establishment, and by expansion in new directions. It does not oper-ate a student training course with a fixed time schedule or with definite periods of rotation through the differ-ent divisions. To state the case positively, the gradu-ate's training course must operate continuously from the beginning of his employment through a long term of years. No period of weeks or months nor pair of years suffice to bring him into contact with all the com-binations needed to qualify him for the larger destiny toward which we hope he is headed. Our first step in selecting a college man is to require that he have a degree. We thus approximate the assur-ance that at least four annual siftings have reduced the chance that a non-worker may find himself in a job where work is necessary. The next step is to try to ascertain facts, from the graduate and from others who have known him at his home and in 'his college, to indi-cate whether our opportunities offer him a career that will challenge his continuing interest, and hold him to tenacious effort against all happenings. We aim to avoid knowingly bringing into our organization a man who will not develop in it enough enthusiasm to keep him happily striving. Having made our selections, we assemble the gradu-ates into a probationary observation circuit. We-put ourselves under their observation by taking them in small groups, usually of two to four men, on a circuit of every part of the Bethlehem plant, in which every manufacturing principle of our steel business is ex-emplified. The probationers work at something from day to day, with their hands if it can be arranged; otherwise in questioning, examining, and note-taking. Their observations include talks with superintendents, foremen, and workmen, the conditions under which workmen labor, apparatus, machinery, methods, design and operation of plant.

Jan 7, 1928

By R. E. Head

Some mixtures of sulphide and oxide ores from the Tintic district in Utah are of a sufficiently good grade to be shipped to the smelter without beneficiation. In mining this type of ore, however, a material tonnage of ore of a similar composition but of lower grade is obtained. It is a question of economics whether such ore should be shipped with a certainty of a small return or concentrated if that would yield a sufficiently increased return to amortize plant construction and upkeep and yield a higher rate of profit than at present. It may be assumed that the tonnage of this borderline ore is constantly increasing and that eventually it will attain such proportions as to justify plans for milling on a relatively large scale. Under existing conditions, the producer of mixed sulphide and oxide ores is not greatly concerned about the physical characteristics of his ore or of its mineralogical complexities, since his contract with the smelter calls for payment on the basis of chemical analysis. When concentration is contemplated an entirely different picture is presented. Percentages of valuable metal content must then be con-sidered in terms of minerals, for it is in the form of minerals that recoveries are made and losses sustained. In describing the performance of a given flotation mill and reagent combination, it may be stated as a generality that a specific percentage recovery of valuable elements is made. Technically, however, the concentrator is really constructed and the reagents are selected to recover the valuable minerals. These considerations must be given prominence in discussing borderline ores from the Tintic district because of their physical characteristics and mineralogical composition. Because of these peculiarities they may be justly termed complex, since their lead, silver, and copper contents are each represented by two or more minerals of different chemical composition and presenting widely divergent physical properties. This paper sets forth the results of a microscopic study of a type of borderline ore from the Tintic district that is now being treated by direct smelting. A

Jan 1, 1939

By W. P. Lass

The gold precipitate from the zinc-dust presses in the cyanide plant of the Alaska-Treadwell Gold Mining Co., Treadwell, Alaska, is treated, in the refinery adjoining, by the Tavener or lead-smelting method. About 3 or 4 tons of this precipitate is produced monthly having 'a gold assay value of $40,000 to $60,000 per ton. It was formerly the practice to treat the byproducts from this process, consisting of 2 tons of slag, 300 lb. of matte, 500 1b. of refinery refuse, flue dust, etc., in a 24-in. water-jacketed blast furnace. This practice was discontinued in the summer of 1914 by reason of the difficulty of keeping the lead-well open when treating a high-grade lead product; of preventing the loss of gold in the flue dust; and of avoiding injury to the general health of the refinery operators; a plain single-phase electric furnace was substituted for the blast furnace. The furnace was constructed from an old steel acid drum by cutting off the top and introducing a cable, made from strands of bare copper wire, through the bottom and spreading the strands out fan-shaped on the inside of the drum. Powdered graphite, obtained by grinding up old crucibles, mixed with 10 per cent. cement, was tamped wet into the bottom of the drum, around and completely covering the copper wires. The graphite was carried up to the bottom of the furnace, or lead-well, and acted as the lower electrode. The sides were built up of ordinary firebrick forming a melting chamber 14 in. in diameter by 20 in. high. The upper electrodes, of graphite or carbon, are 3 in. in diameter and 40 in. long, arranged with joints enabling new electrodes to be connected without shutting down or wasting stubs. A screw feed was arranged for raising and lowering the upper electrode. (Figs. 1 and 2.) The cover for the furnace had three openings, one for feeding the charge, one for the escape of gases, and one in the center for the introduction of the electrode. It was later found more practical to enlarge this center opening to 6 in. in diameter, to allow of a central feeding of the charge around the electrode.

Jan 1, 1916

By G. Camposano, J. Aponte, B. A. Ferguson

The paper covers mining operations and preparation of the ore prior to metallurgical treatment in the Process Plant. Mining operations are primarily concerned with the delivery to Ore Preparation of a balanced ore feed within fairly rigid specifications as to both ore type and chemical analysis. The mining method, systems of geological and engineering control, and the equipment employed are therefore reviewed in this context. In Part One of the paper the physical and geological characteristics of the orebodies, including the varied nature of the ore itself, are first described. Orebody evaluation, the calculation and classification of ore reserves, mining planning and forecasting to ensure continuity of production are covered, and the particular problems presented by sampling, the erratic distribution of ore values and the variation in the density of the ores are also mentioned. Mine design and ore excavation practice are described, together with the way in which they have evolved with recent developments in modern mining equipment. In Part Two of the paper, a detailed description of the Ore Preparation plant is given, centred around the concept of rubbling as a means of separation of the barren hard boulders from soft lateritic ore. Ore blending and ore reclamation operations are explained followed by a detailed description of the drying and crushing plant. The importance of the control of moisture content and ore sizing in the feed to the metallurgical plant is emphasized.

Jan 1, 1979

By Ruifeng Li, Yanghui Ren, Hua Gao

"Since entering the new century, China’s coal industry has witnessed the rapid development, and provided a reliable energy supply for the national economic and social development. But after the “golden decade” of rapid development, the coal industry now is facing overcapacity, low industrial concentration and production efficiency, high pressure of production safety and environmental protection and other prominent issues. Based on defining the connotation of highly-efficient recovery of coal resources, this paper established the relevant 8 indicators to reflect the highly-efficient recovery level of coal resources, summarized the present situation of China's coal resources recovery and the main problems, analyzed the development environment of China's coal industry under the new situation, and finally put forward the strategic measures to promote highly-efficient recovery of coal resources in China.1. Background Coal is the main energy in China. Since entering the new century, China's coal industry has made significant progress, and the level of production safety, resource recovery rate and mining mechanization increased significantly, which provided a reliable energy supply for the rapid development of the national economy. However, due to the changes of China's economic environment, slow growth of energy demand and other factors, some prominent contradictions in the coal industry have significantly restricted the healthy development of the industry. The first problem is serious overcapacity. In the past few years, 16 industries including coal, electric power, chemical and others have invested in coal mines. It is reported (Han 2016) that only during the nine years from 2005 to 2014, the fixed assets of coal industry increased totally more than 3.3 trillion RMB, which brought a large number of production capacity. Affected by the slowdown of economic growth and energy structure adjustment, Chinese coal demand has reached the peak platform and caused the overcapacity of coal supply, so shutting down the backward capacity is the most important task in the future. The second problem is the low efficiency of coal production. There are about 4.3 million coal mine workers in China, and the annual coal production per capita is less than 900 tons, while it was reported (EIA 2016) that the annual production per capita in the United States is more than 10 thousand tons. The third problem is that the green coal resources are not rich. Among the 1.53 trillion tons proven reserves, only about one third are green coal resources in accordance with the principle of ""safety, technology, environment and economy"". The coal resources with high quality and easily mining conditions are not abundant."

Jan 1, 2017

By Mitsuru Tanahashi

Oxidation removal of boron from molten silicon by injecting oxygen and highly basic CaO-CaF2flux powder has been investigated with special attention to the dynamic behavior of the injected flux particles and gas bubbles. Since oxygen gas is injected into the melt, high oxygen partial pressure is maintained at the flux-O2-Si interface and the removal of boron proceeds under nonequilibrium conditions. By applying this process, boron concentration in metallurgical-grade silicon can be reduced to a single-ppm level. In this paper, the effects of the dynamic behavior of the flux particles injected into the silicon melt and the area of the reaction field (the flux-O2-Siinterface) formed in the vicinity of the flux-gas exit of the injection nozzle on the rate of the boron removal are discussed from the viewpoint of process dynamics. The experimental results clarified that the boron removal rate is affected by the kinetic energy of the flux particles which is determined by the injection conditions, such as the gas-flow rate of oxygen and the size of the flux particles. At higher oxygen gas-flow rates, the injected flux particles are expected to possess a significantly high kinetic energy such that they penetrate the O2-Si interface formed at the nozzle exit, which results in the formation of a new reaction field for boron removal. On the other hand, at lower gas-flow rates, the injected flux particles possess too low kinetic energy to penetrate the interface. In this case where the formation of the reaction field is limited, it is shown experimentally that the rate of the boron removal is constant, independently of the flux injection rate.

Jan 1, 2006

By Allen H. Rogers

It has always seemed to me that there is a certain similarity between the work of the mining engineer and that of the doctor of medicine — each has very often to be governed in his actions by conditions which he cannot see. It is not necessary to detail the unseen conditions with which the mining engineer or geologist has to deal—the further extension of ore-bodies, the existence of new ones, the throw of a fault, the probable change in grade' or character of the ore with advance of the workings, are a few of the conditions which the mining engineer has to determine as well as he can from the deductions he is able to make from what he can observe. Just so the physician is often confronted with conditions that he can not observe. Probably less than half of human ills make a manifestation at the surface of the body from which definite and certain conclusions can be drawn. The diagnostician must observe various things and, from these observations in combination, conclude what his course should he to bring about the cure of the trouble. Both professions would be assisted immensely by any agency that would permit them to look below the surface, something that would make more certain the diagnosis which each is called upon to make. The physician has had such an agency since 1895, when Röntgen discovered the X-ray; which, by making possible shadowgraphs of the osseous portion of the human body, advanced immensely the diagnosis of bone lesions Later, with improvement in the technique and more understanding in the interpretation of what the photographic plate shows, other portions of the human anatomy could be examined and at the present time there is hardly an instance of internal disorder to which the aid of the X-ray is not called. Some organs are made opaque by administering mineral substances; in other cases, conclusions are drawn from barely perceptible shadows on the photographic plate. Generally the surgeon's knife is directcd with exactitude to the seat of the trouble and so not only is the difficulty revealed but the necessity for an exploratory operation is averted. What the X-ray is to medicine and surgery, geophysical prospecting methods are to the mineral industry. They give the mining engineer and geologist information regarding subsurface conditions which otherwise

Jan 1, 1929

By A. Probst, N. Moores, J. A. Finch

"In 1994 McGill and INCO (Sudbury operation) initiated transfer of technology originally developed to detect level in flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud-line and solids load. The probe consisted in a vertical tube with 32 equally-spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth (so-called conductivity profile) from which the mud line and % solids could be inferred. The probe was installed in October 1994 and has been successfully detecting profiles since then. This communication includes a description of incidents and experiences during this technology transfer process including: probe installation and start-up; software modifications to accommodate operating conditions and operators' needs; calibration procedures to adjust to changes in performance as a consequence of long term use; and preliminary observations on the last stage, still in progress, signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.IntroductionThickening is one of the basic unit operations in mineral processing and hydrometallurgy used to separate suspended solid particles from a solid-liquid dispersion by gravity settling. As the dispersion enters the thickener, the solids settle and clarified water overflows the top. A thickener, which may be continuous or batch, is basically a large vertical cylindrical tank provided with devices to feed the dispersion and to remove the settled solids. The tank provides residence time for the particles to settle. The dispersion enters the thickener through the feedwell whose function is to dissipate the momentum of the feed stream and to create relatively quiescent conditions around the entering point. Rotating rake arms move the settled solids towards the discharge point located at the bottom centre of the tank.There are normally three distinct zones in a thickener: a top layer of clear water, a middle layer called a sedimenting zone in which particles are settling, and a bottom layer called a compression zone in which particles are pressed together as a consequence of the weight of accumulated particles. Proper operation of a thickener requires two simultaneous conditions: no solids in the water overflowing the top and the target solids content in the underflow pulp. To achieve these conditions is difficult because sensors for detecting the sediment line (interface between clear water and sedimenting zone) and the solids content in the compression zone are not commercially available."

Jan 1, 1998

By Francis C. Frary

OF the five metals that now show the highest figures for annual tonnage production in the world, three (iron, copper, and lead) have been known and used by man for many thousands of years. The fourth (zinc) did not come into general use until the Middle Ages. Only the fifth (aluminum) is of, ultramodern origin, as far as mankind is concerned. Discovered in 1825, and first publicly exhibited at the Paris Exposition in 1855, aluminum was still so difficult to obtain that it was more expensive than silver, until the development of the dynamo provided cheap electricity and the development of the present electrolytic process for its production made it possible to make large quantities cheaply. Even today, the world production of aluminum is only about one per cent of the world production of iron, although about half that of copper by weight. The increase in production from a few tons to more than a million tons per year began with ,the development of the Hall-Héroult electrolytic process, which was first commercially operated by Mr. Hall's company, The Pittsburgh Reduction Co., in 1888. During the relatively short period of time that has elapsed since that date, it has been necessary to develop all the metallurgical and fabricating information required for the production of useful articles of the metal and its alloys, together with experience in both their production and their use, so as to be able to fit them satisfactorily into their proper places in our complex modern civilization. The fundamental properties upon which the usefulness of aluminum depends are its lightness, workability, resistance to corrosion,

Jan 1, 1953

By George Mah, Charles Wert

Internal-friction peaks caused by diffusion of oxygen and nitrogen have been observed in ytterbium. They are thought to be caused by the redistribution, under stress, of strain dipoles around an interstitial oxygen or nitrogen and a neighboring substitutional impurity. With the use of a simple geometrical model, diffusion coefficients for oxygen and nitrogen between special interstitial sites have been calculated. a) APPLICATION OF INTERNAL FRICTION TO MEASUREMENT OF DIFFUSION RATES IN DISSOLVED INTERSTITIAL ATOMS In bcc metals, the interstitial atoms occupy the centers of cube faces (0, 1/2, 1/2), or their equivalents, the center of the cube edges (0, 0, 1/2). An interstitial atom in this position causes an aniso-tropic distortion in the lattice. When stress is applied, mechanical relaxation can take place by the movements of the interstitial atoms. This relaxation has been used to obtain information concerning the movements of the interstitial atoms in the bcc metals. Data for these alloys have been compiled by Stanley and Wert. Other researchers have extended the investigation of interstitial diffusion to the close-packed metals. Gupta and weinig2 found an oxygen peak in a titanium, the height of which is linearly dependent on the oxygen concentration. They assumed, therefore, that they were dealing with movement of atomic ally dispersed oxygen in titanium. KG and wang3 determined that the diffusion coefficients of carbon in fcc steels and in nickel obtained by internal-friction methods were consistent with those obtained by macrodiffusion methods at much higher temperatures. Bisogni found oxygen and nitrogen peaks in hafnium by use of which he deduced the diffusion coefficient of these gases in hafnium. He observed further that the half-widths of these peaks corresponded almost exactly with those of a single-relaxation process; he assumed it to be caused by movement of atomically dispersed oxygen and nitrogen. From these studies, the deduction can be drawn that, in general, diffusion data can also be obtained for the interstitial diffusion in close-packed metals (or more precisely, in slightly impure close-packed metals). One group of such metals for which little data exist for the diffusion of dissolved oxygen and nitrogen is the rare earths. They have great affinity for gases, which enter solution interstitially. In this investigation results were obtained for the Yb-O and Yb-N interstitial solid solutions with traces of substitutional impurities; these solid solutions are of fcc structure. b) MECHANISM OF THE RELAXATION IN FCC CRYSTALS In the fcc structure, an interstitial gas atom is usually situated in the octahedral position (1/2, 1/2,

Jan 1, 1964