Search Documents

By D. D. Bolstad, S. M. Dar, T. W. Smelser, H. C. Pettibone

The use of roof bolt supports has reduced the number of fatal and nonfatal roof fall accidents in coal mines. Roof fall accidents, however, still occur far too frequently. Roof bolting plans are based almost entirely on trial and error, which inevitably leads to underdesign or overdesign with regard to bolt length, spacing, tension, and bolt type for the specific conditions. Underdesign poses safety problems, and overdesign leads to unnecessary costs. Guidelines are needed to select and design optimum roof-bolt plans that will maximize safety and minimize cost. Despite the use of 100 million roof bolts per year, the theory of roof bolting remains underdeveloped. Underground tests designed to provide this knowledge have been only partially successful owing to the many uncontrollable geologic variables present in underground mining situations. The Bureau of Mines believes that the best approach is to conduct a laboratory model study in correlation with finite-element analysis (FEA) and field verification, where these variables can be tightly controlled and measured. A physical model allows precise performance measurement of different bolt types as a function of a wide range of precisely measured parameters. Although the model being used is idealized and limited in size, it serves as a reliable basis for confirming the mechanism of rock reinforcement by bolting and the accuracy of the computer FEA approach to modeling mining problems.

Jan 1, 1984

By D. R. Hanson

The acoustic vibrational spectra of impacted rock slabs were examined at the Denver Research Center, US Bureau of Mines, in an attempt to characterize the behavior of partially detached mine roof rocks. The ultimate goal of this study was to develop a technique or instrument that could provide a quick, accurate, quantifiable measure of mine roof stability. The power spectra of unstable rock slabs were found to contain more energy in the range of 200 to 1000 Hz than solid rock. Comparison of the power contained between 500 and 1000 Hz with that between 3000 and 3500 Hz provided a quantitative measure of rock stability. A lightweight prototype field instrument was designed, constructed, and field tested. This battery-powered instrument computes the power contained in the two frequency bands, compares their magnitude, and displays a number related to the stability of the block tested. Field tests showed the instrument provided reliable measurements of block stability even under conditions of noise that would have seriously degraded the accuracy of the standard methods of roof sounding.

Jan 1, 1986

By B. R. Reddy, P. V. R. Bhaskara Sarma

A process for the separation and recovery of cobalt and nickel was optimized for a sulfate leach solution of Indian Ocean sea nodules containing 80 g/m3 cobalt and 730 g/m3 nickel using the sodium salt of Cyanex 272 as the extractant. Extraction of both cobalt and nickel increased with an increase in equilibrium pH and extractant concentration. The extracted species with respect to cobalt appears to be CoA2.3HA. More than 99.6% extraction of cobalt was achieved using 0.04M solvent in a three-stage counter current simulation at the A:O phase ratio of 3:2. The co-extraction of nickel was about 0.6% only. Two-stage countercurrent stripping of cobalt from the loaded organic at an A:O ratio of 1: 7 resulted in a pregnant electrolyte enriched by 0.8 kg/m3, thus enabling a ten times overall enrichment of cobalt. From the cobalt free raffinate, nickel extraction was carried out using 0.25M solvent in two countercurrent stages, and the extraction showed a 99.8% recovery. Stripping of nickel from the loaded solvent was carried out at an equal phase ratio with the advance electrolyte of pH 1.75 in two countercurrent stages. The nickel stripping efficiency was found to be 98.8%. The present studies indicated that complete recovery of cobalt and nickel was possible using nine counter-current stages.

Jan 1, 2002

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By Robert Glass Cleland

BECAUSE of the country's vast mineral resources, Alexander Von Humboldt, the great German scientist who visited Mexico, or the Kingdom of New Spain, a hundred and fifty years ago, very aptly called that country the "Treasure Chest of the World." During the three centuries of Spanish rule, mining was the principal industry of the kingdom, the largest contributor to the country's prosperity, the chief common denominator in Mexican economic life. Public revenues and private fortunes, employment and markets, agriculture and trade, charities and churches, the incentive for frontier settlement and exploration, and the funds for outfitting the expedition of colonizer and conquistador-all were dependent upon the streams of precious metals that flowed century after century from the mines of Guanajuato, Zacatecas, Real del Monte, San Luis Potosi, and scores of other minería that lay scattered everywhere throughout the land. Sonora, one of the oldest and most renowned of the frontier provinces of New Spain, had been the scene of a hundred rich strikes, sudden stampedes, and widely heralded bonanzas long before the famous and frenzied Gold Rush

Jan 1, 1952

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By Xiaolin Cheng, A. J. Sinclair

"Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeo chemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:<equation>where all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemico-mineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Roger Wilmoth

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the U.S. Environmental Protection Agency?s, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open-Pit Highwalls Demonstration Project. This project is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome U.S., located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 metres (m) and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied insitu treatment technologies included: 1) A modified, furfuryl alcohol resin sealant, utilizing wood and agricultural by-products to coat the rock surface. 2) EcobondTMARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface. 3) Two ARD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: 1) ASTM D 5744-96, Accelerated Weathering of Solid Materials using a Modified Humidity Cells, 2) mine wall residual wall rinse sampling, 3) microscopy, and 4) core drilling followed by water injection testing.

Jan 1, 2003

By C. F. Cornell, Henderson, A. F. Dunyon, D. A. Dahlstrom

IN processing magnetic taconites several steps of crushing, grinding, classification, and magnetic separation are required to produce a 60+ pct Fe concentrate. Usually the final concentrate is in a slurry form of 55 to 70 pct solids by weight and is further characterized by a particle size of 60+ pct -325 mesh. In taconite plants already completed or under construction the conventional method used to obtain pellets suitable for blast furnaces is to filter the concentrate slurry, ball the filter cake, and then harden the green pellets in a traveling grate or in a vertical shaft furnace. Large tonnages must be handled in minimum floor space, with reduced maintenance and lowest possible operating cost. Filtration must therefore achieve two objectives: 1) high filtration rate-in terms of pounds of dry solids per hour per square foot of filtration area-at a low filtrate solids concentration, and 2) a filter cake moisture that will always permit efficient balling within the normal fluctuations of plant operating conditions. If moisture contents are too high, balling may be impossible or result in a mushy ball without enough green strength for the firing operation.

Jan 3, 1957

By I. N. Zavarine

THE present paper is a continuation of the work on the relationship between the magnetic and the phase transformations in carbon steels during quenching. An account was given by the author in a previous paper1 of an investigation of this relationship during a continuous quench. The experimental difficulties then encountered prevented a conclusive proof of the existence or absence of such a relationship. The conclusions of the previous paper were derived indirectly. The present paper deals with the same problem, but the method of attack is modified. The technique developed by Davenport and Bain2 in their well-known study of austenite transformation at subcritical temperature was adopted in the present investigation.. They have shown that the austenite to martensite transformation can be caused to proceed at a relatively slow rate by quenching steels into a hot metal bath. Slowing down of the rate of transformation, together with an observation by Lewis3 that a eutectoid steel can be preserved in the nonmagnetic state by such quenching, pointed out a possibility of a study of both transformations .under more favorable conditions than previously described. The preliminary steps were connected with the technique of the hot bath quench. To study this phase of the present work a modification of the apparatus previously described1 was used. The modification consisted in the use of a hot quenching bath instead of brine, and in fixing the secondary and the primary coils of the apparatus in a stationary position in and around the bath. Tubular specimens, as in the previous investigation, were heated in a suitable furnace to a temperature in the austenitic

Jan 1, 1935

By R. E. Reed-Hill

Recently Levine applied the Conrad-Wiedersich17 equation where H is the activation enthalpy, v the activation volume, T* the effective shear flow stress, T the absolute temperature, and ? the strain rate, to an analysis of titanium single-crystal data. The activation energy as a function of testing temperaturs obtained from specimens oriented for single (1010) prismatic slip is shown in Fig. 12. This diagram indicates a different linear dependence of H on T in the temperature interval from 220° to 300°K than from 0° to 220°K. Levine interpreted the break in this curve as indicating a change in the thermally activated mechanism controlling the flow stress. The purpose of this communication is to point out that the data in Fig. 1 is not consistent with the concept of a flow stress controlled by a simple thermally activated mechanism between 220° and 300°K. The Conrad-Wiedersich relation assumed that the strain rate can be expressed by:

Jan 1, 1968

Diffusion in Solid Metals. BY ROBERT F MEHL (Institute of Metals Division Lecture Tech Pub 726 in Metals Tech, Aug , also Trans, vol 122 22,500 words ) Diffusion in solid metals constitutes one of the important fundamental phenomena in metallurgical behavior Apart from its obvious importance in processes such as chromizing, carburizing, nitriding and calorizing, it plays an important part in the processes of homogenization, age-hardening, and transformations in steel, its scientific importance is no less great Diffusion may occur within a grain, along a grain boundary, or upon a surface, though the exact and even the relative values of these separate processes are known for only a very few cases The requirement of solid solution formation presents the possibility of identifying solid solution phases by a study of diffusion layers Some distortion accompanies diffusion, leading to little¬ understood grain-size changes Distortion assists diffusion though usually it dis¬appears before diffusion has become extensive In a binary system the rate of diffusion is the more rapid in the lower melting metal Many of the published data are too qualitative to permit sound scientific conclusions Age-hardening data may be treated as diffusion data and rates of reaction in steel could profitably be studied from this point of view Studies on diffusion are of great importance to the develop-

Jan 1, 1937

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

ALTHOUGH discovered as long ago as 1817, by Strohmeyer, the use of cadmium did not become in anyway general for nearly a century. Its properties, although well known, did not recommend it to users of metals generally, and it was, on the whole, regarded more in the light of a nuisance to zinc producers than anything else. Its real value was not appreciated until both the United States of America and Germany, who are entirely dependent on outside sources for their supplies of tin, were faced with the unpleasant fact that their tin stocks were being rapidly depleted, with practically no prospect of having them replenished. This resulted in serious efforts being made in the UnIted States of America to conserve what tin was available, and, as a consequence, several metals were tried in the hope that they would prove satisfactory substitutes for tin. Among these was cadmium, and it was found that cadmium could replace tin in a manner sufficiently satisfactory to permit of its use in many directions where tin had been used before.It is on this ability of cadmium to replace tin that its use became in any way general at first; but since then new avenues of development have been opened up in which its physical and chemical properties are proving their value. It is highly probable that its use will extend very considerably as time goes on. OCCURRENCE OF CADMIUM.There are several cadmium minerals known, but none of them occur in profitable quantities as ores. The cadmium of commerce is derived almost entirely from zinc minerals and ores in which it is almost invariably present in proportions which are usually very small. Cadmium behaves metallurgically almost the same as zinc, and hence constitutes a fraction of 1% of almost all spelter.

Jan 1, 1923

By F. R. Ingalsbe

THE proposed revision of the mining law as set forth in the Arentz Bill, now before Congress, is centered about the pretty commonly acknowledged f act that the present law is outlawed both by the large mining companies and the United States Land Office. By common agreement, the law of the apex is non-opera¬tive as between adjacent properties in many instances, and this practice is becoming more common. - If this is a fact, there is no escape from the conclusion that the law is antiquated and should be revised to meet modern conditions more equitable. The thing to be considered seriously is in what direction and to what extent the laws should be changed. Before deciding this, it is logical to inquire in what particulars the present law is troublesome or useless. This was all threshed out by the committee of the Bureau of Mines that worked out the proposed bill, but their testimony was not placed before the public, so far as 1 am aware. Most mine managers and engineers connected with producing properties are a unit in agreeing that the law as applied to the underground extension of orebodies, that is, the "law of the apex," as it is called, is the source of more litigation and expense than any other phase of the law, or perhaps than all other phases combined. This being true, it seems that this part of the law should be changed. Another phase which is troublesome and will continue to be so long as there is unpatented mineral land on the Public Domain, is the discovery requirement. The present law requires that a dis¬covery be made before a claim is staked and the courts certainly agree that such must be the case before patent issues.

Jan 7, 1922

By J. D. Corbett

Mining geophysics in 1967 continued to expand with greater application in the exploration and development of mineral deposits. Moreover, geophysical activity increased without the particular emphasis of a Pine Point or Timmins discovery to spur interest. This trend is expected to continue through 1968 as geophysics more and more becomes an integral part of a mineral exploration program. This past year saw the "little black box" of the old-fashioned "doodlebugger" pushed further into the background, replaced by increasingly sensitive equipment of sophisticated design. The trend also is away from the one man geophysical operation wherein the same individual is responsible for the development, design and operation of the field gear, the planning and execution of a survey and analyzing and interpreting the data. In today&apos;s technology a staff of specialists, electronics engineers, mathematicians, physicists-to name but a few- are required to back up the exploration geophysicist in the development of new methods and techniques, in the reduction of the voluminous amount of field data and in the interpretation of the anomalies which can be enhanced by various high-speed computer techniques. Obviously a full back-up staff of these varied abilities is impractical to most exploration companies. However, the equivalent function is provided to the lone staff geophysicist by the many competent geophysical contractors and individual consultants.

Jan 2, 1968

By E. P. Bucklen

Simulation is a tool useful in the evaluation of the probable effect which various changes may have on the performance of time-dependent systems. This is especially true as far as rail transportation in mining is concerned. The VPI-OCR RAILSIM program is a computer program designed specifically for solving a broad range of problems encountered in the design of haulage systems of new mines as well as in the operation of haulage systems in existing mines. This program is one of several computer applications for evaluating mining systems developed at the Virginia Polytechnic Institute and State University under contract with the Office o f Coal Research of the U.S. Dept. of the Interior. The RAILSIM program uses Monte Carlo techniques to introduce variability in the occurrence of events such as would be observed in real systems. Data are required to describe the haulage network, locomotives, stationary facilities, and other miscellaneous parameters. Output from the program lists measures of performance that are useful in assessing the capabilities and limitations of given system configurations. The output information may cover many shifts of operation to indicate the broad range of variation and interaction which can occur as the system responds to varying levels of demand for service. The RAILSIM program was tested extensively in mining operations. The results of some of these tests are used to illustrate the usefulness of this program.

Jan 1, 1972

In Australia a social impact assessment (SIA) is generally required prior to the approval of a mineral resource extraction or processing projects as a part of the Environmental Impact Assessment (EIA) process. In recent years there has been increased attention on the adequacy of the SIA process applied in major project assessment. Most applications have focused on the impact identification process with little attempt given to the community negotiating power over how impacts will be addressed. The impact assessment tends to occur at a single point in time, with no subsequent re-evaluation or ongoing social impact management and monitoring process. The assessments rarely specify how responsibilities for impacts on communities may be apportioned between project proponents and government, and have been inadequate in dealing with cumulative project impacts. In Queensland, concern about these shortfalls have led to the release of the Sustainable Resource Communities Policy 2008 and requirements for social impact management plans (SIMP) to be developed for each resource development in the State. In this paper a &apos;pressure-state-response&apos; approach to impact assessment is used to develop an &apos;impact-response-monitoring-evaluation&apos; (IRME) framework that can be applied to ongoing evaluation and monitoring of social impacts. The framework is applied to coal resource developments in the northern Bowen Basin in Queensland to identify core requirements in a SIMP. The IRME framework is flexible enough to be implemented at various spatial and time scales, for the wellbeing of the local and regional mining and non-mining communities in Australia. The framework can be further examined in other mine developments and could be integrated with the existing mining or environmental protection acts.

Jun 1, 2010

By H. F. Dawes

In China all minerals are, theoretically at least, the property of the Emperor, and the Imperial permission must be got from him for the privilege of working them. A direct tax is levied on this privilege, and by simple command, the Emperor can close a mine at any time. Occult geomantic influences are a large factor in determining the opening or the arbitrary closing of a mine. The location with reference to points of the compass, graves and natural objects, may be really or professedly considered as indicating that those influences are favorable or unfavorable. The consequence, is, of course, that for the authorization and encouragement of any considerable enterprise, friends&apos; at court, practical politics, and more or less bribery, are required. As a result, most Chinese mining is illicit, and is carried on in a small way only. Often along a single vein, or over a small section of mining country, a few individuals obtain rights over all the openings, most probably by loaning money to the head-men of the operators and holding the mines as security for the debt. In such cases, perhaps, for better security, all the ore is reduced in the works established by the creditors, who also handle all silver produced..As the head-men are, for the most part, improvident, and the laws and customs for the collection of&apos; debts are stringent and peculiar, the " officemen" or creditors acquire in time what is practically an ownership of

Jan 1, 1892

By S. Mathur

The southern Florida phosphate deposits that will be mined in the future contain significant amounts of dolomite. Because high MgO levels are undesirable in phosphoric acid production, several flotation schemes for the removal of the dolomite have been attempted. Alternatively, selective flocculation has been suggested as a potential process. A high MgO rock was simulated with a 30:10:60 mixture of apatite, dolomite and silica, respectively. Single mineral selectivity was observed in the apatite-silica and dolomite- silica systems using Polyacrylic acid (PAA) and Poly(ethylene oxide) (PEO) flocculants, respectively. However, no single mineral selectivity was observed in the apatite-dolomite system using PEO. Heteroflocculation, suspected to be the major reason for the loss of selectivity, was minimized by the addition of a site blocking agent (SBA), consisting of a lower- molecular-weight fraction of PEO. Process parameters such as size reduction schemes, flocculant/SBA dosage and pH were investigated to achieve the desired separation. The selectivity obtained in binary mixed-mineral tests was also achieved in the ternary mixed-mineral system, namely, the apatite-dolomite-silica system. In this report, surface chemical characterization of the samples and their flocculation behavior are discussed.

Jan 1, 1995