Search Documents

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By S. G. Gendler

The choice of ventilation schemes in the Northern Mujsky railway tunnel and definition of the nec-essary quantities of air ensuring regulated radiation conditions in the tunnel system has been accomplished. The influence of natural draught on the stability of tunnel ventilation has been estimated. The design of a portal venti-lation gate allowing minimal influence from natural factors is described. The dependence of pressure loss in the sliding ventilation gates on their spanning value of the vehicle tunnel section has been determined. The selection of parameters for an atmospheric air heating system in winter has been carried out. The operation regimes of air heaters, dependent on the temperature of atmospheric air, have been established.

Jan 1, 2009

By C Noble, J Webster-Brown

A survey of selected West Coast Streams was undertaken in Summer 2001, Summer 2002 and Winter 2002 to establish the degree of arsenic (As) contamination in waters and sediments downstream of old coal and gold mine workings on the West Coast. Of the catchments studied, Soldiers/Ford Creek and Rapid Stream showed the most significant elevated As concentrations, predominantly in dissolved form, and evidence of AMD or ARD contamination (high sulfate concentrations and/or acidity). The rate and processes of removal of dissolved arsenic from the water column (attenuation) have been studied in these catchments. The Rapid Stream and Soldiers/Ford Creek catchments are directly affected by adit drainage from the Sullivan and Blackball coal mines respectively. Both catchments have high As concentrations in the sediments, with up to 770 mg/kg in Soldiers Creek and 490 mg/kg in Rapid Stream. Dissolved As concentrations are significantly elevated in the neutral pH waters of Soldiers Creek; typically as high as 100 - 200 ¦g/kg, up to 500 m downstream of the main adit discharge (800 ¦g/kg As). Adit inflows to Rapid Stream were acidic and contained 20 - 30 ¦g/kg dissolved As, with relatively high concentrations of arsenic in the stream water in winter (up to 18 ¦g/kg), but not in summer. Analysis of concentration trends and As:SO4 ratios downstream of these obvious As sources confirmed that dissolved As had been actively removed from the water column, but varied seasonally with greater removal evident in summer. Adsorption of arsenic onto iron oxide in the stream sediments is the most likely mechanism of removal. The Snowy River catchment, on the other hand, has relatively high As concentrations in both the sediments and the water column, but there was little evidence of a distinct AMD or ARD input from the Blackwater gold mining area. Preliminary investigation suggests that dilution rather than attenuation is responsible for decreasing As concentrations downstream.

Jan 1, 2003

By T. A. Muhlare

"Large quantities of slag are produced every year and dumped on slag heaps around the world, posing a potential environmental threat due to contained heavy metals content. Slags are waste minerals produced during furnace smelting of minerals. The contained values of base metals may be released into the environment under natural weathering conditions polluting ground and underground water. Copper losses into slag are a continuous problem in pyrometallurgical smelting operations. Due to shortage of ore concentrate, various mining operations have initiated the recovery of copper from dumped slag. The typical process uses crushing, milling and flotation. These operations create excessive liner wear rates during crushing and milling because the bond work index of copper slag is 22 kWh/t and this is considered a very hard slag. The process also has reduced flotation recoveries and requires high flotation reagent consumption. The present work shows that digestion of the milled copper slag slurry with concentrated sulphuric acid at a temperature of 250oC forms a solid cake and leaching of the solid cake with water is a possible option. However, the consumption of sulphuric acid can have a considerable cost on the recovery process. This can be limited by producing a leach residue containing gypsum and silicate materials as amorphous silica which are suitable for use as an additive for Portland cement. Laboratory results show that 90% copper recoveries can be achieved. The leaching is conducted to prevent silica gel formation and iron co-extraction. Leaching is optimum if silica gel-free solutions and good filterable residue are obtained. INTRODUCTION Slag is a waste by-product of smelting and converting operations in metallurgical plants. Both smelting and converting operations are aimed at iron separation from base metal sulphides in non-ferrous metallurgy. The iron sulphide component of the ore or concentrate is oxidized to iron oxide at higher temperatures in the molten form, and then fluxed with silica and other oxide rock minerals to produce fayalite (2FeO•SiO2) slag (Schlesinger et al., 2011). Slags are generally deposited on dumps and considered to be unreactive materials. Smelter copper slag contains significant concentrations of several potentially toxic elements, including arsenic, lead, cadmium, barium, zinc and copper. These elements can be released into the environment under natural weathering conditions and cause pollution of soils, surface waters and groundwater (David, 1998)."

Jan 1, 2015

By V. T. Dow

Although the titaniferous iron occurrences at Iron Mountain have been known since 1850, exploitation of the deposits has been discouraged by the metallurgical difficulties encountered in treating the complex magnetite-ilmenite material. Because of the intimate association of magnetite and ilmenite, the material is not amenable to known ore-dressing practices. During World War II, industries started moving south and west from the industrial East; iron-ore reserves in the East were being depleted at a rapid rate; and titanium came into demand as a pigment. Imports of ilmenite from India, then the main source, were practically suspended because of lack of shipping space. These factors created interest in possible exploitation of the Iron Mountain deposits as a source of iron and titanium.

Jan 1, 1961

On a worldwide basis trackbound transportation is on the decline. As mining operations progress from open cast operations to underground operations, most utilise mechanised equipment. However, in South Africa hard rock mines, only a small percentage (¦10 per cent) of the production can be generated by mechanised methods and therefore trackbound mining methods will remain the dominant means to transport ore. In the Australian context there may be occasions where the nature of the orebody would dictate the use of rail transportation with the ore being transported from drawpoints by means of locomotives and hoppers. This paper focuses on horizontal rail haulage systems from the stope loading boxes to the shaft station area and will be largely based on South African experience. It is intended that this document will provide a practical guideline for mine designers and planners during the design process. The paper looks at trackbound transport systems and evaluates such items as construction and management of an underground rail haulage system. Current transportation systems for personnel, material and rock transportation are evaluated, gaps in technology highlighted, and recommendations made.

Jan 1, 2005

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Virginia T. McLemore

The Gallinas Mountains are in northern Lincoln County and southern Torrance County, New Mexico, USA where a series of alkaline igneous bodies, including porphyritic latite, trachyte/syenite, andesite, and rhyolite laccoliths, flows, dikes, and plugs, have intruded Permian sedimentary rocks belonging to the Permian Abo, Yeso, and Glorieta Formations. A small amount of bastnaesite, a REE mineral, was recovered during processing for fluorite from the Gallinas Mountains. Four types of deposits are found in the Gallinas Mountains: epithermal REE-F veins, Cu-REE-F veins, REE-F breccia pipes and iron skarn deposits; all are associated with Tertiary alkaline to alkalic-calcic igneous rocks. Alteration includes brecciation, silicification, chloritization, and fenitization. District zonation is defined by Cu-REE-F (±Pb, Zn, Ag) veins that form center of the district, surrounded by REE-F veins. Carbonatites are inferred at depth by the presence of fenitization, carbonatization of the breccias, presence of REE and similarity of the intrusive rocks and mineralization to areas with known carbonatites.

May 1, 2011

The optimisation of a mining operation requires precise ore grade control, metallurgical accounting, and laboratory sampling protocols, which are implemented by using accurate and flawless sampling systems. Good sampling practices, and sampling technologies in these fields have been historically poor and too many existing sampling systems available on the market are flawed in many ways. This is mainly the result of a poor understanding of the Sampling Theory, and the natural result of international standards on sampling that fail to present the Sampling Theory in a logical way, that still promote non-probabilistic sampling, and that fail to address the important details that make a correct sampling system. Many standards barely mention the Sampling Theory in appendices when it should be clearly the main body of a reliable standard on sampling. As a result, many standards show only little expertise in the Sampling Theory. Conventional statistics should only be a scientific tool for the Sampling Theory to reach its height, which has always been well understood by its creators. Conventional statistics can indeed be addressed in appendices of standards in sampling, but not the other way around. Until the Sampling Theory is recognised as the main body of a standard on sampling, incorrect sampling technologies will plague the market, and make it impossible for mining operations to optimise their mining and metallurgical processes. This paper makes a short list of correct new sampling technologies that have been created with respect to the principles taught in the Sampling Theory. Also, suggestions are presented to create better international standards on sampling, which would provide a stronger incentive for manufacturers to build correct sampling systems, and for engineering firms to install only sampling systems that respect the rules of sampling correctness listed in the Sampling Theory.

Jan 1, 2004

By M. E. Tyrrell

Lightweight basic refractories suitable for use in some sections of the all-basic furnace were developed. Potential advantages of such refractories are lower weight, improved resistance to thermal shock, and less tendency to spall off the working face. Plant trials in positions not subject to heavy loading or severe erosion seem warranted. Forsterite (2MgO.SiO2), stabilized dolomite (2Ca0?SiO2 + MgO), and chrome-spinel [(Fe,Mg)0?(Cr,Al) 031 refractories were fabricated using bubbles as the principal component in the brick mixtures. Bubbles were blown from melts of the basic raw materials as they were tapped from a conducting-hearth arc-resistance furnace. The bubbles were graded, bonded with synthetic Forsterite plus mineralizers, dry-pressed, and fired to temperatures of 1,600° C. or over in a gas-fired kiln. Refractory properties of the bubble brick were compared with those of insulating refractories made by burning combustibles out or dense brick mixtures. Lightweight refractories fabricated of bubbles were one-third lighter in weight than dense bricks of like materials. Their mechanical strength was satisfactory, and their resistance to thermal shock was excellent. In tolerance to open-hearth slag and in resistance to thermal shock, the chrome-spinel bubble bricks wore the best of the refractories tested. Basic refractories of the insulating type were about 40 percent lighter in weight than dense commercial refractories, but they were mechanically weak and not suitable for superduty service.

Jan 1, 1962

By Jae R. Lee

Keywords: Self-propagating high temperature synthesis, AlN, Powder synthesis The particle size and shape effects of starting raw powders on the synthesis of aluminum nitride by self-propagating high temperature technique under high nitrogen pressure were investigated with various AlN diluents and Al reactants. It was found that the structure of beds of the starting raw particles largely affected the pore channels for nitrogen gas infiltration as well as the passages for combustion propagation before and during the reaction, resulting in the morphology and purity changes of the synthesized products. The AlN product of purity over 98% with about 30 microns was obtained.

Jan 1, 2005

Effective Dry Density Benefication of Coal

Sep 13, 2010

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By J. A. Yeats

This paper describes the loading to 25MN of a 1.2m diameter bored cast-in-situ test pile founded in the Thanet Sand which was base grouted. The pile was sleeved over the major portion of its length to test primarily the base response of the pile. The results are presented and compared with similar pile load tests in Thanet Sand.

Jan 1, 1989

By C. Lumley

The management of the Anglo Platinum (AP) mining technical systems (MTS) embarked upon a process of defining the strategy for the MTS department. The newly established department forms part of the greater Group Information Technology (IT). The strategic process took place within an environment that had witnessed a dramatic proliferation of IT implementations across the group within the last three years. The IT department has been structured in terms of the classical plan, build and run functions with the applications and integration streams running perpendicular across these three functions. The application stream is divided into commercial and mining technical systems with business systems integration the third stream. The mining technical systems department supports mine management to effectively gather, analyse and disseminate data relating to the ore reserve by integrating a number of strategically selected IT applications to ensure that the safety, legal and operational requirements are met. This service to business is rendered by management of a strategic outsource partner via tightly controlled service level agreements (SLAs). The framework used for creating a mining technical systems department that is empowered to add value to business was formulated using the AP value chain as both the starting point and guiding process to ensure alignment to the greater internal strategy of the business. Keywords: Platinum, Mine planning, Mining technical systems, Value chain.

Jan 1, 2003

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

By Glenn Clarke, Ben Holloway, Barry Lumsden

"BHP-Billiton’s Cannington mine in Northwest Queensland produces a silver-rich lead concentrate and a zinc concentrate. The plant has the capacity to treat 3.1 mta and for the year to June 2006 mean feed grade was 10.3% Pb, 461 g/t Ag and 3.7% Zn. Recovery losses of lead and silver are primarily in the fine fractions. In 2001, the plant was modified when it was determined that splitting the lead feed into two size fractions, and floating the two fractions separately increased fine lead and silver recovery. The fine lead fraction (called the split float) is 80% <16µm and about a quarter of the lead and silver is in the finest fractions. In 2006 to further improve lead and silver recovery a statistical plant trial of magnetic aggregation conditioning of the split float feed was undertaken. While pure galena is diamagnetic the Cannington galena contains iron within the galena mineral resulting in the galena having a paramagnetic, magnetic susceptibility. The trial demonstrated to greater than 98% statistical significance an increase in lead recovery, and to 99% statistical significance an increase in silver recovery, and to greater than 97% significance an increase in the lead in concentrate in the split float circuit. These economic recovery benefits with magnetic aggregation of the split float feed, has led to the incorporation of this technology in the plant.INTRODUCTIONThe BHP-Billiton owned Cannington silver, lead and zinc mine is located in the Australian state of Queensland about 800 kilometres west of the coastal city of Townsville. This is a pastoral area characterised by large cattle farms, low population density and very little infrastructure. The area has two seasons, a wet, hot summer and a dry, mild winter. Because of its isolation and lack of infrastructure the mine has always operated on a fly in fly out basis.Geological drilling defined the resource as 43.8 million tonnes grading 11.6% lead, 4.4% zinc and 538 ppm silver (Walters and Bailey, 1998). At times during its history Cannington has held the crown as the single largest lead and silver mine in the world (Torrisi and Smith 2003). Another unique characteristic of the operation’s history is the rapid progress from discovery to operation. The first drill to intersect the ore body was in 1990 and the mine and plant was commissioned in 1997."

Jan 1, 2008

Recent studies on the physico-chemical properties of molten slags and oxide solid solutions of interest are reviewed. The review covers redox and phase equilibria in slags, viscosity, diffusivity, electrical conductivity, kinetics of interfacial reactions between slags and CO-CO2, interfacial properties and phenomena. Some highlights from ongoing work on modelling phase diagrams, component activity, viscosity and electrical conductivity of multi component slags will be presented and results compared with published experimental data on slags with or without suspended solid phases.

Jan 1, 2004

By B. M. Nyombolo

Mintek has been involved in the development of bioleach technology for many years, initially for refractory gold extraction, and more recently also for base metals extraction. Mintek, in collaboration with its Australian technology partner (BacTech), is the technology provider for the Beaconsfield refractory gold bioleach plant. At present Mintek, BacTech and Peñoles are constructing a demonstration bioleach plant for copper-zinc concentrate treatment. Bioleach liquors produced in all applications have to be neutralized. In the copper-zinc case, neutralization is required for bleeding iron from the circuit and for adjusting the pH value ahead of solvent extraction. In the refractory gold bioleach circuit, neutralization is required for producing a stable iron-arsenic residue. Some of the challenges encountered in each of these neutralization applications are discussed, and examples of results obtained are presented.

Jan 1, 2000