Search Documents

By John E. Gale

Seven, 15 cm diameter, cores of gneissic granite, four containing induced fractures and three containing natural fractures all oriented normal to the core axis, were tested in an uniaxial compression mode over a range of 0 to 30 MPa. At given normal stress increments, over two or three loading and unloading cycles, the flowrates and changes in fracture aperture were measured. The induced fractures gave lower initial (at low stresses) and lower final flowrates (at maximum stress) than the natural fractures. Both types of fracture exhibited permanent fracture deformation between loading cycles as well as highly nonlinear, with distinct hystersis, loading and unloading flowrate-stress curves. A significant finding of this stud is the breakdown of the cubic law for fracture flow in induced fractures subjected to normal stresses greater than 20 MPa, with the breakdown occuring at much lower stresses in natural fractures.

Jan 1, 1982

ON THIS page is a photograph of a machine that has played a key role in the recent history of Kennecott's Ray mine, situated in the Mineral Creek District, Pinal County, Arizona. It is a huge, rugged, Diesel-powered, rubber-tired truck, having a capacity for carrying fifty tons of ore. It has, to a substantial degree, revolutionized the business of moving broken rock by cutting down both maintenance and operating costs. From 1911 until the end of 1954 Ray had produced 79,000,- 000 tons of ore by underground block-caving. However, in 1947 [ ]

Jan 1, 1957

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

By R. Harris, M. Misra

Column flotation technology has a demonstrated potential for recovering clean coal from high-ash waste fines. The effect of different variables such as air flow rate, frother addition, depressant addition, percent solids and particle size on the quality of separation are discussed. Results indicate that air flow rate and depressant addition are the important variables which control the selectivity in the flotation of fine coal in a column cell. Separation efficiency achieved with column cells is significantly better than that with conventional flotation cells. Under appropriate experimental conditions with a deep column, more than 80 percent coal can be recovered in the concentrate containing 10 percent ash from waste fines containing over 60 percent ash.

Jan 1, 1988

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By H. Polat, M. Polat, S. Chander

A high shear treatment step was observed to improve flotation of coal. The effect of high shear treatment (HST) was a strong function of coal rank, however. For the low rank coals the HST produced loose, open-structured agglomerates which decreased the entrapment of ash minerals. For the high rank coals, the high shear treatment promoted detachment of low-floating particles from the agglomerates that ordinarily formed in a flotation cell. The extent of agglomeration and detachment of particles from the agglomerates was a function of the amount of dodecane and coal rank. To obtain desired efficiency of separation ethylene-propylene oxide block co-polymers were used. The results showed that the HST-flotation technique increased the ash rejection considerably for both high and low rank coals, though the mechanisms were different.

Jan 1, 1995

By M. G. Karfakis, K. P. Chong

Determination of fracture toughness using the semi-circular specimen, the chevron edge notch round specimen, the short rod specimen and the cylindrical burst specimen, are critically reviewed. These methods, among all, are the most applicable for fracture toughness determination of rocks. They require minimum machining. Samples are small, and testing procedures are simple. They have a sound analytical basis and allow the fracture toughness to be determined without measurement of fracture length.

Jan 1, 1986

By V. Miller

Highly variable milling procedures within a geologically complex porphyry copper deposit owned by Kennecott Corp. in Nevada made it necessary to estimate copper recovery and concentrate grade in areas where actual test data was lacking. Estimation was made by first determining the relationships between desired metallurgical properties and the ore's petrology-copper mineral type, rock type, and copper grade. This relationship was then combined with previously estimated rock type, mineral type, and copper grade data in the mineral block model to predict milling properties.

Jan 1, 1985

By Y. C. Kim

To generate a most profitable, ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1992

By M. D. Bishop

Loss of organic solvent extraction circuits occurs through several accepted methods. Losses are commonly attributed to entrainment of the plant organic and evaporative loss of diluent. Evaporative losses of diluent have been estimated using various models or by considering all losses over and above entrainment to be due to evaporation. Other possible loss mechanisms are discussed and data on losses during weather conditions are presented. Accurate estimation of evaporative loss is vitally important to the industry due to both cost factors and environmental concerns. Data for and description of the Diffusive Flux Model are presented as an improved-method of estimating evaporative losses:

Jan 1, 1999

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to mining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1984

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 8, 1950

By Francis T. Christy

One aspect of ocean mining that is frequently overlooked in discussions is the problem of establishing some form of legal control over the seas. Much of the discussion centers on mining in territorial waters, which are controlled by the various countries according to the Geneva Convention on the Continental Shelf, and perhaps by political subdivisions of countries such as the individual states of the U.S. But as technology improves and the mining of deeper waters becomes feasible, the problem of rights outside the continental shelf and territorial waters becomes a significant factor for anyone expending the time and capital for development. Several schemes are possible for regulating ocean mining but as yet none have been instituted, except what might be termed the "wait and see" approach. Even some of the coastal states in the U.S. have no regulations governing mining in the territorial waters under their jurisdiction. Until some regulation is formulated, there may well be little development in ocean mining due to the high risk of capital involved, both with respect to companies wishing to invest their own funds and financial institutions funding a venture to develop offshore mineral deposits.

Jan 7, 1968

By E. Richard Randolph, Rolland L. Blake, Stanley H. Ward, Gerald J. Anderson

During the last 30 years the inductive electro- magnetic method has been used chiefly in the search for massive sulphide mineralization. This application has met with varying degrees of success and in recent years has resulted in discovery of several large orebodies. Little has been written concerning its use in exploration for soft iron ores, but one of the present authors has reported on experiments with massive magnetic deposits. To augment the exploration tools available to geologists in delineating iron orebodies, Cleveland-Cliffs Iron Co. and McPhar Geophysics Ltd. undertook in 1953 to apply the inductive electromagnetic method to Cleveland-Cliffs properties in the Lake Superior region. As a result of this project, equipment has been developed that enables simultaneous transmission of two audio frequency waves, and the field technique and interpretative procedure involved have furthered exploration in the district significantly.

Nov 1, 1955

By Thomas Connolly

The Homestake Mine is situated in the northern portion of the Black Hills of South Dakota in a series of steeply dipping and highly folded Precambrian Rocks. The ore bodies are localized along plunging anticlinal and synclinal folds which are locally called "ledges." The gold bearing ore is confined mainly in the Homestake formation which is an iron-magnesium carbonate series of rocks. The individual ore bodies are pipe or lense-shaped zones which plunge 30º to 75º from the horizontal. These ore bodies range from 10 to 100 feet wide and 50 to 400 feet along the strike. Gold values are erratically distributed in a gangue consisting of cummingtonite schist, sideroplesite schist, quartz, pyrrhotite, arsenopyrite, chlorite schist and ankerite. Usually the ore bodies dip at 70° to 80º and often have folded shapes like "fish hooks" or "troughs." Ore grades must be determined by extensive sampling and all mining is based on assay control.

Jan 3, 1974

By Robert J. Timko, Lincoln Derick

This work is a follow-up to previous research that attempted to predict the location of spontaneous heating episodes in underground coal mine pillars. The objective of the original work was to see if the data obtained by commonly used detection methods could accurately predict spontaneous combustion episodes in coal pillars. Data accumulation during the study was enhanced when a spontaneously generated fire occurred within one of the pillars being examined. The fire provided researchers with realistic data that could be used to determine if fire prediction was possible. Results from the initial study found that the atmospheric status equations that were used provided little advance notice that combustion would occur where it did. This study reevaluated the accumulated data by applying it to recently developed equations and compared these results with previously obtained information to determine if a combination of these techniques could more effectively predict impending combustion.

Jan 1, 1995

Jan 1, 1942

By Naum S. Malts, Victor M. Sizyakov, Nikolai S. Shmorgunenko

A method has been developed in the USSR for processing the low-grade high-silica raw material by sintering the aluminacontaining mixes, which is widely used both as a principal process and in combination with the Bayer process. The process parameters were obtained on the basis of a study of interaction and equilibrium states of the individual profiles of a multi-component system Na20-A1203-Fe203-CaO-Si02 at the sintering temperatures. The compositions and melting temperatures of eutectics of the individual profiles are given. It is shown that the most easily meltable mix is one having a red mud as the main component. The variations are given of the sinter physical characteristics and recovery of the useful components with the sintering temperature. Considerations are given on selection of a sinter leaching flowsheet and directions are shown for improving a series method of processing the low-grade raw material.

Jan 1, 1984

Although geophysical methods of prospecting have proved indispensable in the search or oil deposits elsewhere; it is only 'in recent years that they have been used to any significant extent in Australia. The increase in their use has been quite remarkable over the past two or three years, due in Sao small measure to the encouragement given by means of Commonwealth subsidy. There is no doubt that the use of' geophysical methods will coxi-tinue to increase and this increase could be greatly accelerated as and when oil is discovered in commercial quantities,This review of their use A in Australia and the remarks and statistics are confined to work on the mainland. There has been, a substantial amount of geophysical work in Papua, but as operating conditions are so very different to the mainland Papua has been regarded as a separate province.

Jan 1, 1962

By J. E. Hoffman, T. J. Keefe, Michael E. Stout, O&apos

M.A. Industries, Inc. has developed and is now offering on a commercially available basis, complete systems to recover and recycle lead from spent SLI batteries. The system begins with the breaking and separation of the component parts of the batteries and subsequent treatment of the effluent water produced by this operation. The recyclable materials recovered from this process are metallic lead, lead paste and polypropylene. The lead paste is introduced into a process to convert it from a lead sulfate to a lead carbonate. The process also regenerates the salt solutions into reusable carbonate. The lead carbonate is then leached into an acid bath where it is later recovered by a proprietary electrolytic process. The metallic lead is recovered in a short rotary furnace producing metal for further refining and alloying. The polypropylene is further washed and then introduced to a reclaim extruder along with the proper modifiers and additives. The resulting resin can then be sold on the open market to injection molding processors. This complete system greatly reduces the amount of waste to be disposed of and completely complies with all applicable EPA guidelines.

Jan 1, 1993