Search Documents

By H. D. Hagen, George W. Abbott

2.2-1. Need for Acquisition Operating Plan. In planning a trip by automobile, a road map is procured and studied. Travel by plane suggests detailed examination of route maps, weather charts, and navigation charts. Planning for construction of a factory, office building, shopping center, or housing subdivision envisages working out a complete development plan. Household needs arc generally jotted clown on a shopping list, with each item checked off as it is purchased. In turn, forwarding of any surface mining project should be undertaken only after an acquisition operating plan has been set out, by checklist, under three general headings: 1. Public relations-a check list setting out applicable Federal, State, and local laws and regulations, and the office, board, commission, and individuals having responsibility for licensing, administration, and enforcement of each such law or regulation. 2. Land requirements-a complete check list encompassing all aspects of land acquisition, ownership, management, control, and disposition, with applicable laws. 3. Water requirements-a full check list embracing all aspects of water development and control, acquisition of rights to use, manner of use, and manner of disposition, with applicable laws and regulations. 2.2-2. Public Relations Aspects of Operating Plan. NEED TO DETERMINE APPLICABLE LAWS. The laws and regulations governing acquisition of land and mineral rights, water and water rights, and the use and control of those rights, vary so much from state to state that one cardinal rule must govern all preplanning: determine applicable Federal, State, and local law at the outset. Changing conditions in the past century have resulted in a multiplication at all levels of governmental agencies interested in, and having responsibility for, acquisition, use, control, and disposition of minerals and mineral lands. The same is true of waters and water rights found in, brought to, or discharged from, the operating site.

Jan 1, 1968

By Charles L. Harness

MINERAL pigments give color, opacity, or body to paint, stucco, plaster, mortar, cement, linoleum, rubber, and similar materials. They must be finely divided, substantially insoluble, and generally inert for such uses. Inorganic pigments may be grouped somewhat arbitrarily as follows: A. Natural mineral pigments dug from the earth. 1. Those consisting mostly of iron oxides, such as hematite and Limonite. 2. Those containing large amounts of clay or noncoloring matter, such as ocher, sienna, umber, and colored shales. 3. Those whose color is not due to iron oxide, such as Vandyke brown (including sap brown, an alkali extract of Vandyke brown), graphite, and terre verte. B. Synthetic pigments. 1. Those containing iron oxide as the essential coloring matter, such as "pure" reds, yellows, and blacks, and Venetian reds. 2. Those not containing iron oxide, such as lithopone, zinc white, titanium white, ultramarine, Prussian blue, and the like. Only groups A and B-1 are discussed here. All the pigments in those two categories, except Vandyke brown, sap brown, and some of the carbonaceous slates, contain, as their essential color constituents, one or more compounds of iron; namely, an oxide-Limonite (2Fe203.H20 to Fe203.4H20), hematite (Fe203), or magnetite (Fe203.FeO). Man's first permanent coloring materials were earth pigments- the ochers, iron oxides, and various iron-stained clays. The caves occupied by prehistoric man and the arts of the ancient Chaldean, Egyptian, and Cretan civilizations bear mute witness to this and also testify to the beauty and permanence of earth colors. As the Roman era developed, earth pigments were pushed from their pre-eminent position by white lead and red lead and in the Middle Ages by zinc oxide. Today, of course, the number of acceptable pigments is very large and on a value basis the group of natural and synthetic earth pigments stands

Jan 1, 1949

By Charles S. Larkey

Numerous papers have been published on the use of graphic methods for determining the best curve for estimating the production decline of oil wells but, as far as the writer has been able to ascertain, nothing has been published showing how curves may be worked out mathematically that will conform most closely to the production data under consideration in any given instance; hence the writer has endeavored to show just how such application can be made. Among the valuation engineers, two types of curves are in current use for the representation of the decline in production of oil wells. One may be represented by the equation, y = krx; this is sometimes known as a percentage curve, for the production for any period is multiplied by a constant rate or percentage to obtain the production for the succeeding period. It appears as a straight line on semilogarithmic cross-section paper. The other curve may be represented by the equation, y = kxn, and is shown as a straight line on logarithmic cross-section paper. In each equation, y represents the number of barrels produced in a given period of time, and x the successive periods of time. The other letters are constants to be determined for each well, or group of wells considered in arriving at the most probable curve to represent the rate of production for a given property. From this the underground reserves may be estimated by extrapolation, or by extending the curve beyond the last known period of production to show the most probable production values for the future. Application to the Burbank Pool Fig. 1 relates to a property in the Burbank Pool, Osage County, Okla. The production is shown as an average per well per month, is plotted to the vertical scale of barrels on the left-hand margin and to the horizontal scale of months at the bottom of the chart. In column y, the number of barrels is listed beginning with May, 1922, as the first month on which to base a decline curve. The type of curve used is of the form, y = krx, or, expressed in logarithms, log y = log k + x log r, in which log k and log r are constants to be determined so that the curve will most closely approximate the production data given.

Jan 1, 1925

Over the past 15 years, Artificial Intelligence (AI) techniques have shown promise of providing the ability to capture `human intelligence' into a computer program. The sub-fields of Expert Systems and Artificial Neural Networks are finding increased use in industry to perform tasks previously considered the domain of human thinking. But, are these methods just a new type of software much like that of the past or is real magic hidden within the lines of code? Will this field continue to enjoy high growth rates and if so, what developments will we see in the near future? Which algorithms and methodologies will continue to grow? This paper discusses a number of paradigms which can be used to create successful applications. There are certain barriers; some psychological - some linked with knowledge acquisition, that must be overcome or avoided to ensure system performance. Development time also requires careful consideration before embarking on an Al project. The paper focusses on constructing goal-driven systems that transfer high-technology solutions from the research laboratory to the plant floor. Respect for system users is of paramount importance - whether their involvement is to access contained information or to participate in program maintenance as new knowledge becomes available. Examples of successful and unsuccessful AI implementation in Canadian industry and academia provide evidence of the importance of this issue. The paper also examines some current constraints on applying AI in the real-world. Among these problems are automated knowledge acquisition, methods to acquire data during run-time, real-time systems (hardware versus software), explanation and justification features and adaptive/leaning systems.

Jan 1, 1995

By J Watson

Electronic detonator technology has been under development for the last two decades. Currently, there are a number of systems commercially available with several others still under development, each with its own unique features. This technology can offer a significant advantage to the drill and blast engineer through their ability to initiate an explosive charge at the æplannedÆ time. This new technology has created huge interest within the drill and blast community and also raised their expectations to produce better blasting outcomes. In many cases, specifications (or even expectations) of desired blast results are not properly defined. Interaction between the input variables (rock mass characteristics and blast design) and results (fragmentation, throw, damage, ground vibrations, etc) and their mechanisms, or relationship to one another, are not very well defined or understood. That is why rock blasting is still considered by many as an art rather than science. With one of the few remaining variables (cap scatter) now controllable, todayÆs blaster finally has the ability to apply science to his trade. Even though electronic detonators are available and becoming more commonly used, current field practices are not always conducive to extracting or deriving the maximum benefit from this new technology. In the authorÆs opinion, the following need to be understood to derive and sustain the maximum value: clear definition or specification(s) of desired outcomes from a given blast; impact of different features in an electronic detonator system (precision, accuracy, flexibility, reliability, etc) and their impact on the desired blasting outcomes; interaction of blast design variables (energy, energy distribution, timing, blast geometry) and their impact on desired outcomes; impact of rock mass variability and quality of blast implementation on the desired blasting outcomes; and critical need to utlilise appropriate tools and systems in order to measure and quantify benefits.In the authorÆs opinion a scientific implementation process is the key to derive the benefits. This paper analyses the industryÆs preparedness to derive the benefits from this technology and proposes a scientific methodology to understand, evaluate and sustain the value from this technology.

Jan 1, 2004

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

By George Rice

WHEN miners in the interior coal fields of the United States began the practice of blasting the coal without undercutting, or what is known as "shooting off the solid," many explosions resulted, some of them of great extent and 'violence, and attended with large loss of life. One of the means adopted for preventing this large loss of life, though not preventive of explosions, was to employ shot firers to discharge the shots when all the other employees had gone out of the mine at the end of the day's shift. This system still prevails in most of the Central and Southwestern mines. Following the disaster at Winter Quarters mine, Utah, May 1, 1900, in which 200 lives were lost, a system of firing shots electrically from outside and when the men were out of the mine was adopted at the mines of the Utah Fuel Co.1 This system has also been used in France in certain mines that are subject to instantaneous outbursts of carbonic acid gas. These outbursts generally occurred at shot-firing time, on account of the blasts releasing the gas held in crevices under high pressure. The system was also adopted at a number of other mines in Utah, at the Cokedale mine, Colorado, at the Dawson mines, New Mexico, and in some mines of the Tennessee Coal, Iron & Railroad Co. in the Birmingham Ala. district; and more recently in certain mines in Iowa and Kansas. At first there was considerable trouble from misfires, and in a few instances from premature firing, while men were in the mine, through the shot-firing lines becoming crossed with power lines. Fortunately, however, no loss of life resulted from such premature firing within the knowledge of the writers, and latterly this danger has been reduced to a minimum by certain measures of precaution. The proportion of misfires, or failures of individual shots to fire, has also been reduced to a very small

Jan 10, 1914

By Howard G. L

The gold treatment plant of Great Western Consolidated N.L. is at Bullfinch, Western Australia, 22 miles north of Southern Cross, which is 100 miles west of Kalgoorlie. A railway to Southern Cross connects the mine with the main Perth-Kalgoorlie line.The plant, which commenced operations on the 31st October, 1952, was, designed by Messrs. Alex: Stewart & Co. in consultation with the technical staff of Western Mining Corporation Ltd. to treat 1,000 long tons a day, made up of approximately equal parts of quarry oxidized ore and underground sulphide ore, by moderately coarse grinding (2-3 per cent plus 65 mesh Tyler) and straight cyanidation without straking. The design had to allow for future treatment of all sulphide ore at the rate of 40,000 tons per 28-day periodand to make provision for the possible later inclusion of preaeration treatment.The test work on .which design was based was done on representative development samples, the mine being divided into zones for this purpose, to check possible local variations from average treatment behaviour. Proposed mill feed mixtures were made up from time to time for complete ore dressing tests, which were conducted in the Western Mining Corporation laboratory at Kalgoorlie.The chief feature of the design was that the plant had to handle the extremes of very soft, poor settling and filtering oxidized ore and very hard, good settling and filtering sulphide ore. On one hand, crushers and mills had to be large enough to handle the sulphide ore and on the other, thickeners and filters had to be large enough to handle the oxidized ores.The design is marked by simplicity, the use of large units of equipment, and flexibility to cope with a variety of ores.

Jan 1, 1956

By T. Wasson

Midland and Isabella counties have been the centers of activities for the year 1932. The major part of the 6,967,000 bbl. produced during the year was obtained from the old Mt. Pleasant field and the Eastern Extension field. The total production to the end of 1932 for Michigan, from all fields since discovery, is 20,679,600 bbl. Production in the Eastern Extension field was obtained from Dundee limestone of Devonian age, at a depth of about 3600 ft. As a result of the year's activity in this area, the limits of the Eastern Extension have been defined. No new fields have been discovered. A number of prospective areas have been drilled and condemned by dry holes. Probably the most outstanding development of the year was the discovery of oil on the Yost farm, in sec. 35 of Greendale Township, Midland County, by the Pure Oil Co., in the early part of December. Production is from the Dundee limestone similar to that in the Eastern Extension but is 4 miles south of that area. The first well has averaged about 500 bbl. per day since completion. It is near the center of a solid block held by the Pure Oil Co., so that rapid development due to competitive drilling is not expected. During the early part of the year the Midland-Isabella area was under proration, but on May 17 proration restrictions were discontinued and remained so until the end of the year. While the Eastern Extension saw the principal activity, some work was done in other fields of Midland and Isabella counties, but very little new production was added. The Vernon field on the north showed a slight increase in production over 1931. The Leaton field decreased. The well in Porter Township, Midland County, is still kept in the production ranks but very little drilling was done in that area. The old Saginaw field, Saginaw County, still remains the only spot in the state where commercial production is obtained from the Berea sand. It showed a slight decline over 1931 with no new producers for the year. The Muskegon field on the west side of the state showed a considerable decline over 1931, but owing to the rejuvenation of some wells by the use of acid this drop was not as great as might have been expected. Only two new producers were drilled in that area.

Jan 1, 1933

By F. Keller, E. H. Dix

The desirable high strength and hardness of the heat-treated strong aluminum alloys result from two distinct structural changes: (1) the formation of a solid, solution by heating at the required temperature for a sufficient period, and the substantial retention of this solid solution by rapidly quenching; (2) precipitation of particles of constituent and coalescence to a critical size to produce maximum strength and hardness. In alloys of the duralumin type, that is, alloys containing both copper and magnesium silicide precipitation takes place at normal atmospheric temperature, whereas in alloys containing copper without magnesium silicide or magnesium silicide without copper, maximum properties are obtained only after an accelerated aging treatment consisting of heating for 15 to 20 hr. at temperatures of about 150" C. The mechanical properties of these alloys subsequent to quenching but prior to aging are ideal for forming operations. Unfortunately, however, the alloys of the duralumin type age very rapidly during the first 24 hr. and aging is substantially complete after four days. For severe forming, such as the heading of rivets, it is desirable that this be accomplished within ½ hr. or at the most 2 hr. after quenching. Alloys containing magnesium silicide without copper also age at normal temperatures but the aging is less rapid and the material can be satisfactorily worked within several weeks after quenching. Some slight aging of alloys containing copper alone also takes place at room temperature but it is unimportant from the standpoint of workability. Any method of retarding the aging at room temperature of the duralumin type of alloys would be of considerable advantage in that the period during which the material could be worked successfully would be lengthened. For instance, in aircraft plants it is customary to supply the workmen with small lots of rivets that should be used within ½ hr . after heat treatment. Such procedure has the obvious disadvantage of being uneconomical, and furthermore there is always the possibility that the workmen would use the rivets after the time limit had expired, or the supply being depleted might use some that had not been heat-

Jan 1, 1931

By Silvana B. Foá

Results from full-scale loading tests showed the use of the dynamic increasing energy test (DIET) to verify the capacity of deep foundations. This method allows the measurement of dynamic resistance - displacement curve and the prediction of the static resistance -displacement curve of the pile-soil system. The comparison between the use of DIET versus the static load test is also considered herein. This work was divided in two different phases, the first accomplished in Salvador (Bahia) and the second in Brasilia (Federal District), both in Brazil. The first phase consisted of field loading tests carried out on piles comprised by an approximate 10 to 12 meters thick deposit of fine saturated sand, overlying a stiff clay layer, which is found in certain areas of the Brazilian Northeast. Two metallic (rail track) piles were field loaded in this site. One of them was dynamically tested and the other was statically tested. The second site belongs to the Post Graduate Program of the University of Brasilia. It is comprised by an approximate 8 to 14 meter think deposit of porous clay, overlying a hard strata of saprolitic state. In this site a unique precast driven centrifuged pile was tested. The DIET procedure has demonstrated to be a tool of fast execution and low cost (if compared to static load test). It is a promising procedure to evaluate the behavior of pile-soil system.

Jan 1, 2002

By William G. Krantz

The increased service demands on some of the products of the National Mallcable Castings Co. prompted it about eight years ago to investigate the electric furnace, both in America and in Europe. The process had already been sufficiently developed in Europe to lead us to believe that the electric furnace would most nearly meet our requirements. After further investigation and consultation with the highest authorities on the subject, we decided upon the Heroult type as the simplest and most practicable. In 1910, we built a furnace of this type, of 300 Ib. capacity, for experimental purposes, and although it was crudely constructed the quality of the material we were able to make justified the installation of a 6-ton Heroult furnace in 1912. This furnace has three electrodes, 17 in. in diameter, uses three-phase, 60-cycle current, and is equipped with Thury regulators, which give US good regulation and a uniform load on the line even when cold melting. The power factor of the furnace is 04 per cent. Since July, 1912, the furnace has been in continuous operation, producing up to the present time over 20,000 tons of both carbon and alloy steels of varying analyses and of exceptional quality. Both cold-and hot-metal charges have been used, with a power consumption of about 150 kw-hr. per ton in the case of hot-metal charges and from 500 to 600 kw-hr. per ton in the case of cold charges. The electric energy consumed varies according to the final analysis of the steel and the amount of refining required. Too much cannot be said about the refining possibilities of the electric furnace, for no other method of steel manufacture can compete with the electric in this respect. In proper operation lies the whole secret of success. That steel has been made electrically means nothing, for when the furnace is operated under oxidizing conditions the quality is no better than that of open-hearth material; but when properly made, electric steel is as good as

Jan 1, 1916

By H. C. Vacher

THE limiting concentrations of carbon and oxygen which may co-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen .thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation with elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Herty1,2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550° to 1600 C. and one atmosphere pressure. Kinzel and Egan3 have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550°. C. In. order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume. a value of 0.0102 at 1580° C. for this

Jan 1, 1931

By D Burgess

Since the days of mandatory high cost pilot plant testing in 6 ft + 2 ft SAG mills autogenous griding/semi-autogenous grinding (AG/SAG), mill specific energy is now calculated by various empirical formulae and pilot testing carried out in small laboratory mills. Barratt (1989) described a method using Bond Indices than adding a single factor of 1.25 to arrive at the AG/SAG specific energy. In 1991 the Canadians developed the SAGPower Index (SPI), test using 2 kg of material in a 300 mm diameter mill. This test has been further developed by Starkey, Hindstrom and Orser (2006). This test now includes a Bond Ball mill work index test.The Macpherson test is still being offered by some testing facilities. This dry test requires at least 180 kg of material.Morrell (2004) formulated an AG/SAG specific energy generator based on a drop weight index Value (DWi). This DWi value is related to the Ab parameter and the material specific gravity. Morrell reconfigured the BondÆs Third Theory formula to cause extra power requirements to be inputed. This technique incorporates the material specific gravity (SG). The AG/SAG specific energy values produced using this method are susceptible to higher values of crushing and rod mill work indices.This paper offered describes a more simple method to generate AG/SAG specific energies. This programme incorporates Bond work indices, the JKMRC parameter Ab measuring impact breakage and the parameter ta measuring the abrasion rate, then employs a series of efficiency values nominated for each transition size (AG/SAG T80). These efficiency values have been compiled over the years from actual operating plants and documented reports.CITATION:Burgess, D, 2012. A method of calculating autogenous/semi-autogenous grinding mill specific energies using a combination of bond work indices and Julius Kruttschnitt parameters, then applying efficiency factors, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By V. R. Garfias

With the exception of the United States and Russia, none of the leading world powers have within their boundaries the oil supplies needed to meet present peace-time requirements, and even in regard to the United States it is admitted by competent observers that the known oil reserves within the country are inadequate to meet demands for more than a comparatively few years. It follows, therefore, that the transportation of petroleum—almost entirely by tank steamers—from foreign fields to the main consuming centers is one of the most important factors affecting the present and future development of the oil industry. The world-wide distribution of petroleum is affected by numerous factors of which international politics is not the least important. The assurance of an ample supply of petroleum—one of the most essential munitions of war—is of paramount importance particularly to those countries subjected to the rivalries of powerful neighbors. And paralleling the importance of the control of an ample supply is that of its safe transportation from the fields to the consuming centers. To illustrate: France is dependent almost entirely on foreign sources for its petroleum requirements estimated at close to 100,000 bbl. daily, and in order to control such a supply after the World War it acquired an interest in the Iraq oil fields. Lately it has undertaken the construction of a pipe line from these fields to the Mediterranean seaboard in Syria with the expectation that late in 1934 these fields will supply between 30 and 40 per cent of the country's requirements. It should be noted, however, that the availability of this supply is entirely dependent on the safe operation in the Mediterranean at all times of an adequate fleet of tank steamers. Thus, in order to transport 40,000 bbl. daily, it will be necessary for one 10,000-ton tanker to leave Tripoli, the Syrian port, say for Marseille, every other day throughout the year while to meet the entire present peace requirements of France from the Iraq fields, a fleet of some 30 such tankers must be kept in continuous operation between Tripoli and Marseille.

Jan 1, 1934

By Earl C. Henry

Magnetic iron ore was mined in Essex County, N. Y., during the American Revolution; Benedict Arnold is said to have mined ore near Port Henry to secure iron for chains and spikes for the Lake Champlain fleet. Details regarding the operations prior to 1804 are not easily obtained but work on a commercial scale appears to have been started about 1838. The Witherbee, Sherman & Co. was established in 1849. The property of the district is held in fee almost entirely by the mining companies. The Mineville iron-ore district, as well as the entire Adirondack region, belongs to the pre-Cambrian complex. The readily identified rocks consist of gabbro, anorthosite, syenite, and granite, and are classed as igneous, eruptive, and intrusive. In addition, there is a great variety of gneisses, rocks with a variable mineral composition but all more or less distinctly foliated. The Grenville series are the oldest rocks in the district; this series consists of graphitic white limestones, graphitic sandstones, and quartzites and gneisses with or without graphite. The orebodies occur in the gneissic rocks and are comformable to the structure of the rocks. The typical occurrence of the ore in this district is in lenticular bodies with a parallel pitch to the southwest; this structure is best exemplified in the New Bed mine. The Harmony and Old Bed orebodies are faulted by two sets of diabase dikes, one set having a southwest strike and the other set an east-west strike. The ores occurring in the acid gneissic rocks are non-titaniferous. The ores occurring in the gabbros and anorthosites are high in titanium; these deposits are irregular, have no structural relation with one another, and are unquestionably of igneous origin. The origin of the gneissic rocks and the ores therein contained is not settled; both the sedimentary theory of ore concentration and the igneous theory of magmatic segregation have been advanced. The iron mineral in all the orebodies is crystalline magnetite; some very perfect and large specimens have been obtained. The gangue is

Jan 1, 1925

By Roland D. Parks

To construct a yieldable metal prop of demonstrated practicability has been the aim of the writer of this article for a period of years. Such a prop is herewith described; it involves a yielding principle not previously utilized, to the best of the author's knowledge, in any of the numerous types of props which are in use in Europe and England or on record at the United States Patent Office.' No attempt will be made in this paper to analyze the situation in regard to the economics of timber substitutes. Suffice it to say that shortage of suitable timber combined with high freight rates has already presented a problem in some mining districts, and in the relatively near future will probably demand considerable attention from the mining industry as a whole. In order to understand the problems involved in the design of timber substitutes for underground support, it will be well to review briefly the fundamentals of ground subsidence and of the action of timber as props. The forces encountered in the support of mine openings are not computable. As a rule subsiding ground moves slowly; but it moves with an irresistible force. The only way to be certain of stopping ground movement is to completely fill up the openings below such movement. This is, obviously, an impracticability from the mining standpoint. The ordinary procedure is to put in timber to hold up the loose back and permit the natural arch above to resist its own loading. Under these conditions the timber rigidly supports the loose; but if the natural arch fails, the timber is then called upon to resist this additional pressure. Usually it cannot do this. The result is a crushing of the supports. Efficient timbering is that which will last just long enough to complete in safety the mining operations necessary to extract the ore. Wood has a cellular structure. It has great longitudinal strength for its weight. Further, it possesses the ability to maintain a high percentage of its strength while it is being crushed. In other words, it rigidly supports loads up to its capabilities and then continues to sustain

Jan 1, 1934

By NA NA

Hausherr UK Limited Win Order from Italian Cement company Cementerie Di Sardengnu SpA, Qualler Hall complete head gear switch in three weeks, Chief Mins Inspector 'cautiosly optimistic' on safety standards at Privatised Pits.

Jan 11, 1996

By J. Githiria, C. Musingwini

"Cut-off grade is a decision-making criterion often used for determining the quantities of material (ore and waste) to be mined, ore processed, and saleable product. It therefore directly affects the cash flows from a mining operation and the net present value (NPV) of a mining project. A series of different cut-off grades that are applied over the life of mine (LOM) of an operation defines a cut-off grade policy. Due to the complexity of the calculation process, previous work on cut-off grade calculation has mostly focused on deterministic approaches. However, deterministic approaches fail to capture the uncertainty inherent in input parameters such as commodity price and grade-tonnage distribution. This paper presents a stochastic cut-off grade optimization model that extends Lane’s deterministic theory for calculating optimal cut-off grades over the LOM. The model, code-named ‘NPVMining’, uses realistic grade-tonnage realizations and commodity price distribution to account for uncertainty. NPVMining was applied to a gold mine case study and produced an NPV ranging between 7% and 186% higher than NPVs from deterministic approaches, thus demonstrating improved project value from using stochastic optimization approaches. Background on cut-off grade calculation and optimizationCut-off grade is a decision-making criterion that is generally used in mining to distinguish ore from waste material. Consequently, it is used to determine the quantities of material (ore and waste) to be mined, ore processed, and saleable product. A series of different cutoff grades that are applied over the life-ofmine (LOM) of a mining operation defines the cut-off grade policy for that particular operation. The cut-off grade therefore directly affects the cash flows to be produced and the net present value (NPV) of a project at the mine planning or feasibility study stage."

Mar 1, 2019

By V.F. Marsters

Peru has produced petroleum since the early seventies, the first work being in the Zorritos field, in the Province of Tumbes, adjoining Ecuador. In the early nineties, the Negritos field, in the Department of Piura, came into prominence, and by 1905 had attained an annual production of 335,160 bbl. The early development of the field was under the general direction of the London & Pacific Petroleum Co., but it is now handled by the International Petroleum Co. In 1900 and 1901, the Lobitos field became the seene of marked activity. In 1905, its total production amounted to 75,000 bbl.; it has continued to increase, as has Negritos. From 1897 to 1902, there was prospecting in the region of La Brieta (or Fernandex), on the Mancora River, about 25 to 30 km. from the coast. Small production of a heavy oil was obtained from three different sands. So far as the author knows, no work has been done in that locality since 1902. There are thus four distinct fields in the north end of the Peruvian coasta1 plain. The remaining productive locality of Peru is the Pirin or Pusi field, at the northwest end of Lake Titicaca, Department of Puno, in southern Peru. The first prospecting near Pusi was done by Brown Brothers, of Los Angeles, Calif., who obtained modest production about 1906; according to reports, activities ceased about 1914 or 1915. The maximum annual production was obtained about 1908, estimated at 76,000 barrels. Peru possesses two distinct geographic provinces in which we may look for the development of a larger oil industry; namely, the coastal plain province, and the inter-Andean plains. Coastal Plain Province The coastal province is most prominently developed in the Province. of Tumbes and the Departments of Piura, and Lambayeque.l It 1 For details concerning the geology of this part of Peru, see Bol. No. 50, Cuerpo de Ingenirros de Minas "Informe preliminar sobre In Zona Petrolifera del Norte del Peru," par V. 1". Marsters.

Jan 1, 1923