Search Documents

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By A Singleton, J Busfield

World coal producers have been under constant pressure in recent years because of falling export prices arising from oversupply and the Asian slowdown. This has resulted in a dynamic market place, a sharpening of focus on bottom line costs and some rationalisation of participants. Productivity has increased dramatically as many inefficiencies, typical of the coal industry, have been eroded through workplace reform. This is true for the both open cut and underground sectors of the industry. At the same time, the technology of underground mining is undergoing dynamic change. Mine operators are implementing better exploration and planning tools and are also starting to make gains against chronically low equipment availability and utilisation. æStep-changeÆ improvements in output are imminent. As the statutory environment shifts to a æduty of careÆ regime, it is hoped that mine safety performance will improve, particularly with regard to fatalities. The focus of the paper is on the Australian coal sector, although references to international benchmarks are made. Despite environmental threats to the future of coal, it is concluded that the next ten years will see impressive performance results from underground coal mines which will assist coal to maintain its position as the preferred fuel of lowest cost.

Jan 1, 2000

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

By M. MacLaughlin, J. Whyatt

A case study is presented that relates statistical descriptions of joint sets to the distribution of local wedge failures along the crest of a catch bench at the Yellowstone Talc Mine. The fracture sets and bench width were mapped by teams of geological engineering students from Montana Tech under the direction of Dr. Mary MacLaughlin. The students analyzed the fracture data, conducted physical property tests, and used a beta version of a NIOSH program “Bwedge” to predict the distribution of surviving bench widths. In the course of this analysis the students developed evidence of software performance issues that, unfortunately, frustrated their analysis. These have now been addressed and a full analysis completed. The analysis confirms the validity of the student mapping program and provides insight into the effects of blasting and excavation practices on the bench. It also provides a tool for exploring the pattern of bench crest failure that would result from variations in both bench geometry and blasting practices.

By G. H. Schnakenberg Jr.

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaustcontrol technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

Jan 1, 2002

By Pollard D, Meadows N

The presence of impurities which are electropositive to zinc in acid zinc electrolyte causes changes to deposit morphology and reduced current efficiency. Glue may be added to control some impurity effects, but assaying for animal glue concentration is difficult and seldom done. Measurement of the activation overpotential for zinc deposition by cyclic voltammetry is used in some plants to monitor electrolyte quality and control glue additions.The deposit morphology and current efficiency of zinc deposition from commercial electrolyte were investigated for various glue additions in the presence of increased levels of antimony. Cyclic voltammetry was investigated as a method of optimising glue additions in the presence of antimony.Scanning electron rnicroscopy showed deposits characteristic of the impurity element present and the glue addition rate. Cyclic voltarnmetry measurements showed some correlation between current efficiency and activation polarisation potential. The importance of using tankhouse electrolytes where results are to be related to tankhouse operation was noted.

Jan 1, 1988

The concepts of capacity and basicity have proved extremely useful in dealing with a wide range of solute species in metallurgical slags, and as a result have been widely applied. These two concepts are reviewed, and it is suggested that the Lewis approach to basicity has much to commend it. In some cases, it appears that the term capacity has been used without due consideration being given to the nature of the solution being formed, or even to whether a true solution was being formed at all. This paper proposes a rigorous definition of capacity, based on the true nature of the solution process in slags and glasses, and briefly reviews the repercussions of this approach on data available in the literature and the limitations which it may impose on future investigations in this area.

Jan 1, 1994

By F. Vincent, A. Boulet, M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. It makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery data to gravity recoverable gold (GRG) to predict overall recovery. The methodology is designed for gravity circuits located in the circulating load of secondary grinding mills. Gold liberation is estimated by processing a sample of representative ore with a laboratory Knelson Concentrator (LKC) in three successive steps, each at a finer grind than the previous one. Breakage behaviour is represented by a matrix H, which redistributes GRG in the feed of the secondary mill in the various size classes of its discharge. Provision is also made to account for gold overgrinding, which decreases the overall amount of GRG. Classification, pre-concentration and recovery data are estimated from plant performance, and are represented by the diagonal matrices C, P and R. The methodology is demonstrated with case studies of greenfield, retrofit and optimization applications.

Jan 1, 1995

By Thomas T. Read

The fact that certain types of ore-deposits have attained their present condition through the action of descending surface waters was, perhaps, first clearly pointed out by Posepny.l The oxidizing effects of such waters were discussed by Pen-rose,2 and many papers dealing with this phase of the subject have subsequently appeared. That secondary enrichment of sulphide ores, however, might be produced by descending surface waters was not clearly understood until after the copper-bearing veins of the Butte district, Mont., had been carefully studied by the geologists of the U. S. Geological Survey, although De Launay3 had suggested that sulphides might be transported from point to point and re-deposited in the zone above the level of ground-water. As a result of the study of the Butte district, two papers by geologists engaged in the work appeared within a short interval. The first by Weed: dealing with the enrichment of veins by later metallic sulphides ; and the second by Emmons; treating of the secondary enrichment of ore-deposits in general. In the latter paper it was pointed out that a typical vein of sulphide ores which has been subjected to the action of descending surface-waters exhibits four zones,—an upper or surface-zone, in which the changes hare been mainly of removal, the products being typically oxides; a second zone of oxide enrichment, in which the less soluble metals brought from above have been precipitated as carbonates or oxides; a third zone of sulphide enrichment,

Jan 1, 1907

By M. I. Hoschke

The viability of pyrometallurgically treating zinc containing materials is enhanced by recovering zinc metal rather than oxide from furnace gases. During the history of zinc production, there has been continuing development on methods of recovering zinc metal that has resulted in three commercial designs in use today. The most widely used commercial technology, currently producing 13% of the world's zinc, is the lead splash condenser which is attached to the Imperial Smelting Furnace (ISF). The other remaining commercial designs are the zinc splash condenser and the Wheaton-Najarian vacuum condenser. The need to treat increasing quantities of secondary zinc materials, particularly Electric Arc Furnace (EAF) dust, has renewed emphasis on the development of ways to recover zinc metal. Development work in this area has proved to be difficult. Partly as a response to these difficulties, studies into the fundamentals of zinc condensation and absorption have been undertaken. Pasminco Research Centre (PRC), Newcastle, is also developing a. new zinc absorber to recover zinc metal from furnace gases:. The design attempts to address the problems associated with current devices.

Jan 1, 1994

By A. Mehmet, W. A. M. te Riele

A pilot-plant investigation in a NIMCIX contactor has shown that activated carbon can extract more than 93% of the gold in return-dam solutions. The average gold concentration in the barren solution was less than 0.003 mg/L from a feed averaging 0.048 mg/L. The carbon was eluted by the Zadra procedure. The operating conditions of the elution-electrowinning circuit are reported, and the elution of the gold and other metals is discussed. The reactivation of the carbon by use of the Rintoul kiln is described, together with the results of reactivation. The consumption of reagents in the process cycle is presented in sufficient detail to allow the economic viability of this technique to he evaluated for the recovery of gold from low-grade solutions.

Jan 1, 1990

By Jafar Safarian

A new kinetic modelling technique has been applied to study the rate of MnO reduction from slags by dissolved carbon in liquid iron. Based on a consideration of the fundamental reaction kinetics, a general differential equation for the slag reduction process has been formulated, which then is solved analytically for certain special cases. By re-writing the solutions in a dimensionless form the poorly known kinetic constants are eliminated, which makes the model both flexible and applicable to a wide range of experimental conditions. For example, changes in process parameters such as temperature, metal composition, slag composition, gas composition can readily be captured along with variations in the crucible geometry. Based on a comparison with a series of experimental reduction curves being reported in the literature, it is concluded that the predictive power of the model is surprisingly good, yielding outputs that are both reliable and physically reasonable. An attractive feature of the model is that it provides an alternative way of calculating the activation energies from experimental reductions curves. For example, it suggests that the activation energy for the reduction of MnO by dissolved carbon in liquid iron is about 90 kJ/mol, which is different from the previously reported activation energies. The model also suggests that the crucible geometry, which affects both slag the volume and the resulting slag/metal interfacial area, has a significant influence on the overall reduction kinetics. This design parameter is a key to further optimisation of the process on an industrial scale.

Jan 1, 2006

By Mowry Bates

THE following example of the practical application of engineering geology is of interest in that it demonstrates the advantage of keeping accurate records of all wells, whether drilled by one's self or by others, together with the advantage gained by gathering such data during the process of development. The fault described was found in the autumn of 1915, during the hurried development caused by the discovery of the famous Gusher Bend pool in Red River Parish, Louisiana. The writer was at the time employed by one of the operating companies as geologist, and the example is a portion of the routine work. LOCATION The oil fields of northern Louisiana and east Texas are located in Caddo, Bossier, De Soto and Red River Parishes, Louisiana, and Marion County, Texas. A very narrow strip of the eastern portion of the latter is productive. The producing oil pools are known as the Caddo Field, in the northern part, and the De Soto-Red River Field, in the southern. The two fields are 60 miles apart. There are several gas fields between then, but no important supply of oil has been found, though there are several producing wells in the Anona chalk, locally called the chalk rock, in the Elm Grove gas field in Township 16 North, Range 11 West (see Plate 1).

Jan 5, 1918

Low tonnage quartz vein-hosted stibnite lodes are widely distributed in rocks of the Tasman Fold Belt System in eastern Queensland, with particular concentrations in the Hodgkinson - Broken River Fold Belt and to a lesser extent in the Gympie Province of the New England Fold Belt: Higher grade deposits have been worked intermittently on a small scale since 1873, resulting in the production of about 5500 tonnes of antimony ore/concentrate with an estimated grade of about 55% Sb. Future production of antimony may be as a by-product from deposits, currently being explored/mined for gold in the Hodgkinson/Mitchell River area and the Amanda Bel goldfield. Establishment of an antimony processing plant in Queensland using the Quelar Process would provide a more reliable market for small producers and could stimulate future exploration and production.

Jan 1, 1990

By Xi Dai

The LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode materials for Li-ion battery were synthesized with Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) as Fe sources by high temperature solid-state reaction method. The Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) materials were produced by liquid co-precipitation method and crystal structure and morphology of cathode materials were characterized by X-ray diffraction and scanning electron microscopy. The composition contents and charge-discharge performances were measured by chemistry analysis and charge-discharge apparatus. The XRD patterns showed that LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode material samples were well-crystallized homogeneous olivine-type phase, with only tiny trivalent iron impurities according to chemistry analysis results. Charge-discharge test showed that cathode materials possessed excellent charge/discharge capacities, about 150mAh/g at 0.1C rate and more than 120mAh/g at 0.4C rate. The polarization of cathode in charge-discharge process can be restrained effectively, for the potential offset between oxidative peak and reductive peak of doped LiFePO4 material was only 0.079V, lower than pure LiFePO4 markedly.

Jan 1, 2006

By Coxhead B. A, Brandt B. A

The geological exploration and evaluation of coal reserves involves the appraisal of very large amounts of data. Computers afford an ideal means of handling and manipulating the data, thereby avoiding the laborious and expensive method of manually compiling the logs in full descriptive language. The Minad system of computer storage and retrieval of geological and analytical data is particularly suited to the description of cores and cuttings from exploration drill-holes. The encoded data is arranged in a 120-column computer output sheet format; descriptive geological information in a 54-column geolog and analytical information in a 64-column assaylog. The acquired data is quantitative, uniform and relatively complete and can be selectively retrieved for processing by a wide range of specialized computer programs developed for the coal mining industry. Visual retrieval of data for manual processing is facilitated by the use of simple codes and logical word abbreviations.

Jan 1, 1977

By James L. Vanderbeek

INTRODUCTION Semiautogenous (SAG) grinding technology first started to be seriously considered for comminution circuit design in the mid-1960s as an alternative to the three-stage crushing circuits and rod-ball mill circuits in vogue at the time. Since this time the application of SAG mill technology has become widespread with over 250 mills larger than 20 feet in diameter sold (Jones 2002). The vast majority of concentrators constructed over the past quarter century have utilized SAG mill technology, and a SAG-based comminution-based circuit is generally the first choice considered for new projects. Since the first generation of SAG milling technology was applied, many lessons have been learned, and new supporting technologies have emerged which make the design, installation and operation of SAG &-based grinding circuits more robust and efficient. This paper will discuss the current status of SAG and associated technologies. MILL MECHANICAL DESIGN ISSUES Table 1 summarizes the manner in which SAG design capability has evolved over the past 30 years. Increases in mill diameter came slowly as the industry took a wait-and-see attitude as the technology of larger mill diameters was advanced. The first 32-foot- diameter mill was ordered in 1969. It was not until 1979 that the technology jumped to the 34-foot-diameter mill and 1988 for the first 36-foot-diameter mill. The first 38- and 40-foot-diameter mills were both ordered in 1996. At least five 38-foot-diameter and two 40-foot-diameter mills will be in operation by mid-2004. Advances in structural analytical techniques and increased computational power, coupled with field measurements of large operating mills, have increased the confidence of the mill suppliers in their designs and the operating companies in the viability of larger diameter mills. No failures of a 36-foot-diameter mill or larger have been

Jan 1, 2004

Information from bores in the LatTobe Valley has been accumulating for over fifty years, and the manual extraction of details has become a limiting factor in their use.Punched card equipment, installed by the State Electricity Commission for accounting purposes, was known to be available for reasonable periods, and it was suggested that this could help in the extraction of data from the voluminous records.Investigation showed that they could be substantially duplicated on cards, with consequent gains on many operations; the cards being regarded as an auxiliary to the existing records.BRIEF DESCRIPTION OF RECORDSAs a bore is drilled a continuous record of the strata is kept, together with notes on the presence of water or any unusual features which the driller may observe.When coal is struck, samples of each ten feet are usually sent for analysis.The location and surface level of each bore is fixed by surveyors, and details of dates and methods of drilling are also kept.Bores are allocated numbers, prefixed by the name of the parish within which they are drilled. Numbers are allocated in conjunction with the Department of Mines, to avoid duplication.Records of strata and analyses are kept in folders, with 100 bore numbers per folder.Standard plans are drawn, showing the locations, bore numbers and surface levels. For each bore they also show the depth and thickness of coal struck, and the total depth drilled.Cross sections are then drawn, connecting the various coal seams, which have been identified by the geologist.

Jan 1, 1960

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

By K McNabb, M H. Turner, P A. Jenkin

Mining of the Agnew nickel deposit commenced in 1970 using a variety of underground mining methods, though with mixed success due to the difficult ground conditions. WMC Resources Ltd acquired the operation in 1989, and commenced nickel production with an open pit. In 1995 all production reverted to the rejuvenated underground mine, using exclusively SLC (sublevel caving) methods. Currently the mine produces 1.4 Mt per annum, at an average grade of 1.74 per cent Ni. Underground mining of the Perseverance orebody has always presented significant challenges due to the difficult ground conditions in the weak and altered ultramafic rocks. The range of problems include areas of swelling minerals, intense and extremely weak shear zones, relatively high in situ stress, and in other areas very brittle rocks. Under these conditions rock mechanics input has been and remains a critical element of the mining strategy. Severe ground behaviour difficulties down to a depth of 500 m below surface prompted a review of the mining strategy for the large disseminated nickel orebody, including evaluation of alternative mining methods. However, sublevel caving was ultimately selected as the preferred method, and a re-design of the SLC cross-cut layout followed. A selection of rock mechanics investigations of interest are described, including complex virgin stress measurements, detailed ground behaviour monitoring, and the use of non-linear stress analyses to re-design the mine layout. Subsequent ground behaviour, support design and production scheduling are also described.

Jan 1, 2000