Search Documents

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By D Beahm

Introduction The Energy Metals Corporation (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin including the JAB Property, one of several potential properties being planned for development as a satellite facility to the greater Antelope Uranium Project. A National Instrument 43-101 Technical Report has been completed for the JAB property. This report estimates total measured and indicated mineral resources on the property totaling 3,555,022 pounds U3O8 contained in 2,400,875 tons at an average grade of 0.073 % U3O8 at a .25 GT cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB Property is located in Sections 13, 14, 15, 16, 21, 22, and 23, Township 26 North, Range 94 West, approximately Latitude 42o 14’ North and Longitude 108o 00’ West (Figure 1, Location Map). This property consists of unpatented mining lode claims and Wyoming State mineral leases comprising approximately 2,100 acres.

Jan 1, 2007

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

How Particles Stick to Bubbles - The Influence of pH and Hydrophobicity in Flotation

Sep 13, 2010

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By B. Tiryaki

Longwall shearers usually suffer from excessive pick and pickholder consumptions and severe wear of the back plate of the clearance ring section of shearer drums. In practice, most of the drums were seen to be withdrawn from the face due to the abovementioned problems, while vane picks and their holders were intact due to the improper lacing design of the clearance ring picks. However, few underground investigations and their results on the effect of lacing arrangement of clearance picks on the service life of shearer drums have been published. Nevertheless, the pick consumption characteristics of shearer drums were not investigated in detail, since these are fewer pick consumptions with shearers when compared to roadheaders. This paper is concerned with the comprehensive in situ trials on the effect of lacing of clearance ring picks on the lifespan of shearer drums, and the pick consumption characteristics of longwall shearers at Cayirhan Coal Mine in Turkey. The lifespan of shearer drums employed with shearers in this mine increased 70 per cent, while the consumption rate of clearance ring picks decreased threefold through using an alternative lacing for clearance picks, indicating the significance of utilizing proper design techniques for clearance ring picks for the service life of shearer drums. Statistical analyses carried out, using the raw pick consumption data, implied that the clearance ring picks experienced much higher loads than vane picks, revealing that special attention must be paid to designing clearance ring picks. An average maximum consumption value of 41 was determined for clearance ring picks, with corner-cutting picks having the most replacements, while it was 35 for vane picks, on three-day based pick replacements.

Jan 1, 2004

By Xingtian Hui

Due to variation in the geological natures of underground coal mines, especially when the entry?s roof/floor are soft and weak, it is vital to select an appropriate roof bolting system to ensure entry stability, coal production, and miner?s safety. No single type of roof bolting system perfectly fits for various types of openings, even within a mine. From the results of continuous research on roof bolting in the past 10 years, the authors used a novel concept of ?Self-screwed? mechanism to develop five types of roof bolting under a patented Self-screwed Tube Bolting System (STBS)©. This roof tube bolting system can be applied to meet different timing-strength requirements under varying mining conditions to increases the stability of mine workings. This paper outlines the structures and mechanisms of the five types of self-screwed roof bolting systems along with their unique characteristics, advantages and disadvantages, and limitations. Two case studies using a Self-screwed Tube Drilling Bolting (STDB)©, one of the five types of roof tube bolting systems, show the principles of mechanics, suitability and parameters for a mine entry and a subway?s construction/ supports in the surrounding soil layers and soft sands, respectively are presented. The results confirmed the time dependent anchorage capacity between predictions and on-site measurements. Currently, other types of the self-screwed tube bolting systems are also being applied to different coal mines in China to increase entry stability and meet safety requirements.

Jan 1, 2009

By John Heilig, Patrick Andrieux

"Near-field monitoring of blast induced seismic vibrations is a practical and useful way of assessing blast field behaviour for diagnosis and optimization purposes. It is also necessary in order to provide the information from which empirical vibration prediction equations, such as the one proposed by Holmberg (11 for example, can be derived. (Strictly speaking, the “near field” extends from the blasthole itself to about one charge length away from it; however, throughout this article, “near field”will.most often refer to the outer limit of this zone, from roughly 0.75 to 1.50 charge length away.) In order to obtain reliable data, proper field monitoring techniques are of paramount importance. Once the data are properly recorded, analysis can be done either in the time domain (describing vibration amplitude vs. time) or in the frequency domain (usually describing vibration amplitude vs. frequency)."

Jan 1, 1995

By A. C. T. Bigg

"The mineral potential of the Nanisivik area was discovered as far back as 1910 when a prospector of the Geological Survey of Canada, on an expedition under Captain J. G.Bernier, recorded a deposit of pyrite with minor sphalerite and galena. An outcrop of the present orebody was discovered by Texas Gulf Company in 1957. Subsequent drilling outlined the orebody consisting of 6,000,000 tonnes of ore containing 13 % Zinc and 1.5 % Lead. The orebody appears to have been formed by the filling of a limestone cavern with sulphides. The sulphide minerals consist of pyrite, sphalerite and galena. The limestone bedrock is mostly dolomite with some calcite and magnesite. A cutoff grade of about 6% Zinc has been calculated.In 1972 Mineral Resources International Limited took an option on the property. Upon completion of the feasibility study by Watts, Griffiths and McOuat, the then new independent project management group of Strathcona Mineral Services Ltd. were engaged to develop the project through the financing, construction and operating phases. Strathcona Mineral Services still manage the project from their head office in Toronto and through the Mine Manager and Department Superintendents at the Mine site. The interest for the project is presently split five ways: Mineral Resources International Ltd. 53.5 %, Government of Canada 18 %, Metallgesellschaft A.G. of Germany 11.25 %, Billiton B. V. of Holland 11.25 % and Texas Gulf Co. 6 %."

Jan 1, 1980

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By Douglas Rudenko

Most engineers, mine operators, or contractors acknowledge the importance of having accurate subsurface information in order to plan a project or solve a problem. Conventional methods of exploring the subsurface such as augering, core borings, or test pits can provide information, but it is often costly and sparse. Geophysical methods offer an alternative to help supplement sparse information~ gathered through conventional exploration techniques.

Jan 1, 1998

By R. A. Kearns

Biennially the Bureau of Mines issues a list of equipment that has been accepted as approved or permissible during the two calendar years immediately preceding the date of publication of the listing. By so doing the mining industry is kept informed of the availability of the latest equipment for safe use underground. This list supplements Bulletin 543, Permissible Mine Equipment Approved to January 1, 1953; Information Circular 7722, Permissible Mine Equipment Approved During the Calendar Years 1953-54; Information Circular 7840, Permissible Mine Equipment Approved During the Calendar Years 1955-56; and Information Circular 7957, Permissible Mine Equipment Approved During 1957-58. This list includes equipment meeting those standards that have been revised since Information Circular 7957 was .issued. Schedule 16E,4 a revision of Schedule 160, was approved May 19, 1960.

Jan 1, 1961

By B. Hilscher, P. Nayak, N. Yoon

"The mining industry is currently facing challenges with declining feed grades and is struggling to find solutions to improve the project’s economic value. By means of pre-concentration, ore sorting aims to separate the barren material from the valuable ore to reduce energy consumption and tailings generation, while increasing the feed grade, concentrate grade, mill recovery, and revenue. In addition, ore sorting allows the modification of deposit geometallurgy in order to allow the creation of an optimal mill feed.This paper evaluates the applicability and challenges of ore sorting by utilizing the results from four different mines, and reviews them in detail. The mines include two underground and two open pit mines that are base metal and precioius metal operations. In order to understand the applicability of ore sorting in these operations, initial rock-by-rock test results and different types of assays (atomic adsorption [AA], inductively coupled plasma [ICP], and fire assay) are utilized. Using the assay results, the grade recovery curves for ore sorting are generated and they are further improved by using and developing an ore sorting algorithm, which is discussed in this paper. The application and evaluation of ore sorting in greenfield and brownfield properties will also be discussed.The state of the art ore sorting technologies for both rock-by-rock and bulk sorting are reviewed in this paper. The future technologies on the horizon, including different combinations of sensors, are explained. The sorting technologies include, X-ray transmission (XRT), X-ray fluorescence (XRF), colour, infrared, electromagnetic, and laser induced breakdown spectroscopy (LIBS).IntroductionOre sorting is a sensor-based sorting technique introduced between the excavation stage and processing stage, where the unwanted waste is diverted to the waste dump and only the ore is sent to the mill for further processing. As a result, the quality of the material entering the mill is improved and the dilution of the ore is reduced. In greenfield projects, sensor-based ore sorting provides an opportunity to reduce the capital cost of the project and increase the return on investment (ROI). With most operations currently facing the challenge of finding a high grade deposit, having a sorting unit provides several advantages while keeping the cost at minimum."

Jan 1, 2017

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Ed Cope

The newly discovered South Arturo deposit is a Carlin-type, breccia-hosted, oxide gold deposit located on the Dee Mine property at the north end of the Carlin Trend in Nevada. The Dee Gold Mine was discovered in 1981 by Dee Delamar, a Cordex geologist. The property was put into production by Rayrock Mines in 1984. During its 16-year mine life, the Dee Mine produced about 18.6 t (600,000 oz) of gold from oxide ore at an average production rate of about 1.24 to 1.55 t/a (40,000 to 50,000 oz/year). In October 1997, Bar-rick Gold Exploration acquired the right to earn a 60-percent interest in the Dee property from Dee Gold Mines through an exploration farm-out agreement. Barrick Gold Exploration began exploration activities on the property in 1998 and vested in its 60 percent operating interest in 2004. However, the discovery hole at South Arturo was not drilled until July 2005 from atop the historic mine dumps located 300 m (985 ft) south of the Dee openpit. The discovery hole (BD-72) encountered a cumulative 75.6 m (248 ft) of oxide mineralization grading 1.9 g/t (0.055 oz/st) gold beneath 260 m (855 ft) of dump material and post mineral Tertiary Carlin Formation volcanic and sedimentary rocks. Oxidation within the deposit extends to depths greater than 610 m (2,000 ft). The deposit has passed the prefeasibility test and is presently in the feasibility stage. Exploration is on-going to enhance or enlarge the known deposit. The current resource for the deposit stands at 40.4 t (1.3 million oz) of gold. The South Arturo discovery is an example of an historic mining property yielding a new discovery through the diligent application of area selection criteria of the model type and persevering when early results were generally negative. Barrick?s original exploration pro-grams on the property were focused on the discovery of deep, high-grade sulfide deposits that would likely be mined by underground methods. As it turns out, South Arturo is mostly oxidized and will be amenable to mining by openpit methods

Jan 1, 2008

By P. Sklenicka

Remediation of the environmental (and social) disturbances caused by opencast brown coal mining in the past in north-west Bohemia isa priority for state environmental policy. In order to provide a concept for full restoration of land following disturbance by opencast mining, a special interdisciplinary project supported by a grant from the Czech Ministry of Environment was started in 2000. The initial stage of the project was intended to summarize and evaluate the findings and the works carried out in connection with various reclamation activities in the afflicted area over a period of more than 50 years. The main aims of the three-year project are to make use of the best available landscape environmental management knowledge in order to harmonize the ecological, aesthetic, productive and social functions of new valuable landscape, including the recovery of historical continuity and an understanding of ?landscape memory?. The basic landscape functions were assessed on two different scale levels. On a large scale, the relevant attributes were investigated over the whole area of the Sokolov brown coal basin (220 km2). The data and experience acquired were used to define large-scale guiding principles for the rehabilitation of a post-mining landscape. On a small scale, the basic characteristics and functions of the landscape were analysed in the Litov-Chlum model area (2 km2). The information derived from this analysis was used to formulate a small-scale approach for the rehabilitation of the model area and also to define general methodological principles. Keywords: rehabilitation, post-mining landscape, degraded landscape, non-productive priorities

Jan 1, 2004

By Fred N. Kissell, Andrew B. Cecala

In This Chapter [Where methane is emitted at longwall faces Where methane accumulates at longwall faces Using the modified shearer-clearer to eliminate ventilation eddy zones Using a walkway curtain to reduce methane buildup during the headgate cutout Control of frictional ignitions and The best location for the methane monitor] The methane released along a longwall face represents only 10%–20% of the total methane emitted from the entire longwall panel. Nevertheless, in very gassy coal seams, this methane released at the face can pose a problem because the shearer is a ready ignition source. Preventing methane ignitions at longwall faces requires four actions. The first is to provide better ventilation around the shearer to eliminate the ventilation eddy zones at the drums where methane builds up. These eddy zones are eliminated by mounting additional water sprays on the shearer to direct air into them. The second action to prevent methane ignitions is to install a water spray behind each cutter bit and regularly replace worn bits. Water sprays behind each cutter bit act to quench the hot metal streak that follows a worn bit when it strikes rock. The third is to ensure that no ventilation eddy zones are inadvertently created by poor placement of water sprays. The fourth is to ensure that the methane monitor on the shearer is in the best location to detect methane accumulations. ADDRESSING METHANE ACCUMULATIONS AT LONGWALL FACES3 Cecala et al. [1985a, 1989] and Denk and Wirth [1991] studied methane emission and ventilation patterns at longwall faces to find where methane accumulations are most likely. Although not always the case, the major source of methane at longwall faces is usually the breakage of coal by the shearer. Stress-related fracturing of the coal seam at the face, called bumps or bounces, can cause the release of additional gas (Figure 4–1).

Jan 6, 2006

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982