Search Documents

By R. H. Doremus

From measurements of carbide precipitation rates in a iron it was concluded that the carbides nucleated on dislocations in both strained and unstrained samples, except for the latter at lower temperatures and higher carbon concentrations, where there were more muclei than could form on the dislocations. The equation of Cottrell and Bilby for the segregation of atoms to dislocations was found to be inapplicable to this system. No satisfactory theory for the growth process is available. A study of the rate at which a second phase separates from solid solution can frequently reveal much about the mechanism of separation. There are still many features of the precipitation of carbon from a iron that are not understood, although this system has been examined extensively. To provide more insight into the mechanism of carbide precipitation in a iron, rates of this process were measured at different temperatures, carbon concentrations, and densities of dislocations in the iron. The concentra- tion of carbon in solution was followed from the height of the internal-friction peak; this height is directly proportional to the amount of carbon in solution and is not affected by the growing carbide particles. In this paper these rates are compared with those found by earlier investigators, and the mechanism of precipitation is discussed in light of these results as well as two earlier studies1, 2 and the electron microscopic work reported in the preceding paper. EXPERIMENTAL The amount of carbon in solution was followed by

Jan 1, 1961

By L. C. Morganroth

From a geological standpoint, but scant attention has been paid to fire-clay beds. Only within the last few years have they been the subject of individual investigation, prior to this time having been considered only in their relation to coal seams. While the relative importance of coal and fire clay is still immeasurably in favor of coal, yet an industry as large as that of fire clay is entitled to a measure of attention. A discussion of the Carboniferous clays is practically a discussion of the clay beds in the Appalachian basin, since more than 90 per cent. of these clays mined are from this region. The clays are confined to the northern end of the basin, or the States of Pennsylvania, Ohio, Kentucky, Maryland and West Virginia, ranking in importance about in the order named. The clay deposits of the Carboniferous period have been divided into two classes; those found in the Pottsville conglomerate series of rocks, ' and all those that are found in the formations above, for the reason that the clay beds above the Pottsville series all resemble each other in properties, composition and appearance, and all are distinctly different from the bed found in the Pottsville formation. The bed of clay found in the latter formation is unique in that flint clay is practically restricted to it. (A variety of flint clay is occasionally found in these upper deposits but this is in such small amounts as to be negligible.) Carboniferous clays occur between stratified rocks; sandstones, limestones, etc., in the same manner as coal veins. They are often accompanied by a coal vein although where the clay is of a workable thickness, the coal is generally too thin to work. The clay beds are sometimes known by the name of the coal seam at which horizon they occur. Clay beds may be from a few inches up to 20 ft. in thickness. They may consist of all soft clay, all flint or both soft and flint. The Carboniferous clay beds of Pennsylvania are the most important of any of the clay beds found in the country, and are among the oldest ones worked. We know more about this clay geologically for the reason

Jan 1, 1916

By J. D. Braun, C. W. Powell

Diffusion between gold and indium at two temperatures below the melting point of indium (155.4oC) was investigated. The major, component of the diffusion zone was determined to be AuIn2; the other, intermediate phases in the system occur in much narrower layers In order of decreasing layer width these are: Au9In4, AuIn, Au4In. Inter diffusion coefficients of the four intermediate phases and the terminal solid solutions lie in the range of 2.4 x 10-l3 to 1.8 x 10-11 sq cm per sec. WHEN two metals which do not form a continuous series of solid solutions interdiffuse, each phase in equilibrium at the diffusion temperature should appear as a separate layer in the diffusion zone. In the Au-In system, diffusion plays a significant part in many commercial applications, particularly where indium alloys are used as solders for electrical contacts with very fine gold wire, for estab- lishing electrical contact to thin metallic films, and for mounting metal-coated piezoelectric crystals. A knowledge of the number, extent, and type of phases which form at diffusion temperatures below the melting point of indium, 155.4oC,1 and the diffusion constants for the system would be useful for these practical applications. Of more basic significance, additional information on polyphase diffusion in a system not previously investigated would be gained. The phase relationships in the Au-In system were determined primarily by Kubaschewski and Weibke1 and are based on thermal, microscopic, and X-ray analysis, Fig. 1. There are five intermediate phases in the system having approximate compositions corresponding to the formulas: Au4ln (ß)—80.0 at. pet Au; Au3In (?)— 75.0 at. pet Au; Au9In4 (d)—69.2 at. pet Au; AuIn—50.0 at. pet Au; AuIn2—33.3 at. pet Au. Solid solubility of indium in gold at 700°C is reported as 12.64 at. pet and at 406°C as 10.36 at. pet. No solid solubility of gold in indium is reported.

Jan 1, 1964

By M. E. Lombardi

The cost of maintaining the production of an operating oil company is one of the most important, as well as one of the most difficult to estimate, of the various items which go to make up the total cost of producing oil. In the opinion of many operators the cost of drilling and developing new wells, whose, production takes the place of the loss in production through decreased yield of the old wells, is considered an operating expense, for the reason that the total income-producing power of the property is not increased. The cost of these new wells may be added directly to production expense, or it may be charged to capital account, and this account depreciated to the same extent. In either case, after an oil company is on a satisfactory income-producing basis, the money for drilling new wells to maintain production must be taken from the income of the company. Three factors determine the cost of maintaining production: First, the rate of decline in yield of the wells; second, the cost of drilling and equipping new wells in terms of their production; third, the decrease in initial production of new wells as the property is drilled and gas pressure taken off the sands, etc. In order to check theoretical figures for the cost of maintaining production the writer, with the assistance of Reed Bush and Fred Tough, has compiled the following figures. It is necessary first of all to choose a' period of time during which production for the field or territory studied remains fairly constant. The longer the period of time over which this condition prevails, the better. It is also necessary to eliminate or allow for any extraneous condition which may have affected the production returns, such as the shutting down of a large number of wells, the bringing in of a well of exceptionally large yield, the opening up of virgin territory where the flush yield is greater than will be had from new wells in after years, etc. All these conditions are exemplified most simply in the case of the Coalinga field, and perhaps these figures are more truly prophetic than the two other cases given. In applying these figures to the future it is well to assume that the average yield of new wells will constantly de-

Jan 1, 1916

By C. L. Baker

The district of Catoree, San Luis Potosi, ranks among the first half-dozen silver-producing camps of Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapnni, Mazapil, Palomas, Musquiz, Minas Viejas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (610 m.) in 41/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catoree from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catoree, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to crosivc forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstone?, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains: some of this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution of the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebblcs, and finer detritus. According to tradition, the higher portions of the Sierra Catoree were forested with pines and cedars but none remain within the mining district, although cedar is found farther south in the range. The vegeta-

Jan 1, 1922

By Frank L. Antisell

Certain physical and chemical properties of copper are so intimately related that a change in variation of the physical properties indicates a certain chemical change. The standard specifications of copper of the American Society for Testing Materials are based upon physical characteristics with one exception, namely, the copper contents. The physical standard includes electrical properties, defects in the "set or casting," variation in dimensions, weight, etc. Paragraph 4 of the specifications states, " Wire bars, cakes, slabs and billets shall be substantially free from shrink holes, cold sets, pits, sloppy edges, concave tops, and similar defects in set or casting." Shrink holes and concave tops indicate both physical and metallurgical defects; cold sets, sloppy edges, etc., indicate physical defects only; small pit holes may be indicative of either or both physical and metallurgical defects, depending on conditions under which they originated. To the refiner, a copper casting, no matter how made, is known as a "shape," irrespective of whether it is wire bar, ingot, cake, slab, billet, etc. As practically all shapes are cast in an open mold, that is a mold without cope, the surface of the shape cools in contact with the atmosphere and has a coating of oxide. Certain phenomena of the surface indicate the adaptability of the metal for forging or rolling. The writer believes that it is much simpler to produce shapes that are metallurgically correct than those that are mechanically satisfactory. When copper is to be rolled into thin sheets or drawn into very fine wire, the slightest physical defect becomes evident. It is, therefore, of the utmost importance to consider every characteristic of the shape and ascertain the physical and chemical relationship. Pitch and Set.—The appearance of the surface of the copper when cooled is considered as to its "pitch," or the general contour of the surface of the shape (which may vary from a concave to a convex); and the '" set,"' or the detail appearance of the surface of the shape (the wave-like structure). When the shape presents a concave surface, it is known as "low pitch;" a convex surface is known as "high pitch" or "tough pitch;" and a level surface is called "flat pitch." The set of the copper is, in a very large measure, directly related to the pitch; and so intimately are

Jan 1, 1921

By W. Klement

By quenching liquid alloys, single-phase solid solutions are obtained in the ranges 0 to 42.0 at. pct Co-Au and 0 to 15 and 75 to about 100 at. pet Co-Cu. Metastable solid solutions are also found in multiphase 42.0 to 49.0 and 69. 0 to about 100 at. pet Co-Au alloys. fie inability to achieve complete solid solubiliiies in Au-co and cu-co alloys is rationalized by a conszderation of the rate processes during cooling and solidification. Trends in lattice distortion and shifts in the compositions of the melting-point minima and critical points are discussed for the binary alloys of copper, silver, and gold with some of the transition metals of the first long period. By rapidly cooling alloys from the melt, a continuous series of metastable solid solutions can often be obtained for components of similar crystal structure which normally form eutectic systems.' The eutectic system Au-Co, Fig. 1, and the peritectic system Cu-Co, Fig. 2, were investigated in order to determine the extent of the metastable solid solutions attainable with the present technique.* EXPERIMENTAL PROCEDURES Most of the alloys were prepared by melting weighed quantities of the elements (purity greater than 99.9 pct) under hydrogen in alumina crucibles by means of induction heating. After reweighing, the alloys were cast under argon into 1 mm diam wires. However, it was not possible to prepare some of the Cu-Co alloys with the requisite homogeneity (over about 1 mm3) in this way. For these alloys, reduced powders (purity greater than 99.9 pct) were mixed for 12 to 48 hr, pressed into compacts that were sintered at 1000º to 1050°C for 6 to 48 hr under hydrogen, and then furnace-cooled. Alloy charges of a few mm3, cut from the cast wires or chipped from the sintered compacts, were heated to 1550º to 1600°C in 30 sec in an alumina insert held within a graphite support and then ejected by a pulse of helium onto a lightly polished copper strip on the inner periphery of a rotating wheel. The

Jan 1, 1963

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By Charles Camsell

Few persons ever stop to consider how vital an influence minerals, and especially metals, have had upon human history, how they have affected the every-day life of the individual or how at different periods they have altered the course of nations and determined their progress. Students and writers of history have dealt very fully with political history and have given us a great deal of detail about the careers and policies of kings, parliaments and nations, but frequently have not touched the economic causes that have been the real forces influencing the development and carrying out of these policies. So far as minerals are concerned there is no single work from which one can get a concise and consecutive account of the growth in the use of minerals, nor of the diverse ways in which the. geographical distribution, the .search for, the development and the use of mineral resources have affected human progress from the beginning of man's history. The reason for this is quite plain, and when one takes a little time to think of it he begins to appreciate the magnitude of the job and he will realize that the story of minerals and mineral resources touches a tremendous range of human activity, not only of mining .and metallurgy, but the whole field of agricultural and industrial growth, of exploration and colonization, transportation and commerce, monetary system, commercial policy, in short, almost every phase of economic life.

Jan 1, 1926

By Borje Hjortzberg-Nordlund

THE great Swedish export iron ore mines are Kiruna and Malmberget in the north above the Arctic circle and Grängesberg in Central Sweden, see Figs. 1 to 3. These mines exported in 1951 about 13 million metric tons of high grade iron ore and concentrates. The origin of these three ore fields seems to be the same. They are of pre-Cambrian age and are regarded as typical instances of primary eruptive ore that has thrust up as glowing masses of lava flow between two somewhat older beds of porphyry. Apparently the ore and the porphyry became segre. gated from common parent magmas by a process of differentiation. Despite the fact that the Kiruna orebody belongs to the earliest pre-Cambrian formation, it has been influenced to an unusually small extent by later metamorphosisms, apart from its having been set on edge through folding and wrenching off by a number of later faults. The Kiruna ore occurs along a stretch of more than 4 miles as a series of slabs or lenses sloping steeply toward the east and sandwiched between two beds of porphyry. The main orebody has a length of about 3 miles and an average width of 300 ft with a maximum of 600 ft. The dip varies from 65" to 45" toward the east and the known depth is 3000 ft, although magnetic surveys indicate it may be at least 6000 ft. Malmberget has undergone a more thorough transformation, having been pressed and crumpled into a meandering band of disconnected layers and lenses. The largest of the more connected bodies of ore, the Great Ore Layer, outcrops on a low mountain ridge and has a total length of about 4 miles and a maximum width of about 300 ft. The dip varies from 30" to 70" towards the north. The main orebody in Grangesberg, the so-called

Jan 1, 1953

By C. Birch, M. Katuruza

"The purpose of this study was to demonstrate unmanned aircraft system (UAS) technology in opencast highwall mapping using the experience at Isibonelo Colliery in Mpumalanga Province of South Africa. In opencast mines, geological mapping has evolved over time and there have been challenges in extracting valuable information from exposed highwalls due to restricted access for safety reasons. A UAS was used at Isibonelo Colliery to conduct highwall mapping, using drone-based digital photogrammetry techniques. A demonstration survey was undertaken during February 2018. The highwall flyover demonstration was planned for two areas (North and South pits) where field control points were placed by the mine survey department. A contractor used a DJI Phantom 4 (Pro) for the highwall mapping. Raw data was processed within 48 hours and a 3D model of the mapped pit area was produced. Further data extraction included obtaining updated weathering and lithological contact elevations and thicknesses for use in short-term planning. The results showed a good correlation between the resource model and the UAS data model. The project was considered a success and highwall flyover mapping and is now standard practice at Isibonelo Colliery.IntroductionDetailed geological mapping is crucial to the understanding of the structure of any mineral deposit. Several mapping methods may be applied depending on the available exposure/outcrop and nature of the orebody; for example, coal deposits typically suboutcrop only, therefore an opencut highwall provides the best exposure for mapping the geology. Mapped information, when incorporated into a resource model (generated from exploration borehole data), improves the understanding of the orebody or coal seam. This research paper focused on the use of unmanned aircraft system (UAS) technology for pit highwall mapping to generate data for updating geological models and avail the latest information to mine planning to improve the short-term plans."

Mar 1, 2019

By James Norman, O. C. Ralston, John Dasher

MOST mineral products are used in the finely divided state, but some are sold in larger sizes. Coal, gravel, metallurgical fluorspar, phosphate rock, hematite, chromite, and other products are sold in sizes coarser than can be treated by many mineral-dressing methods. Gravity separation of coarser sizes by log washing and jigging is probably as ancient as any process now in use. The performance of jigs on a feed with sufficient difference in density of the minerals is excellent, but many families of minerals are too similar in density to be separated effectively by this method. The use of heavy suspensions of fine solids to separate coarse coal from bone and slate has been in use for some years. This separation by sink-and-float was limited until recently to light minerals. Development of galena and ferrosilicon as suspension media, by Minerals Beneficiation, Inc., at Mascot, Tenn., Pitcher, Okla., and Crosby, Minn., under patents granted during and since 1938, has permitted excellent results to be obtained on minerals of very similar densities up to 3.3. This process has been put in the hands of American Cyanamid Co. for exploitation, and further research now in progress may increase the density of suspension obtainable so that separations at a density of 4.0 may be practicable before this is published. The Huntington-Heberlein dense-medium process, developed in England, is also being commercialized in the United States by Sink and Float Corporation. Du Pont has developed a sink-and-float separation using halogenated hydrocarbons as parting liquids; at this writing, the method is used commercially only on coal but has been successful in the pilot plant on many other minerals using tetrabromethane at densities up to 2.95. While these processes were being developed to extend the range of separation by difference in density to the coarser sizes, the Bureau of Mines was engaged in developing a process that will extend the range of separation by difference in wettability up to 2-in. size. War work has pushed aside its further development indefinitely. The results are published here with the hope that some use may be suggested that will justify post-war development, and so that readers that may be able to make immediate use of the scheme may have the information. EARLIER WORK It has been known since the time of Herodotus (B.C. 484(?)-425) that water-repellent particles will adhere to sticky surfaces. That early historian reports the

Jan 1, 1942

By Borje Hjortzberg-Nordlund

THE great Swedish export iron ore mines are Kiruna and Malmberget in the north above the Arctic circle and Grängesberg in Central Sweden, see Figs. 1 to 3. These mines exported in 1951 about 13 million metric tons of high grade iron ore and concentrates. The origin of these three ore fields seems to be the same. They are of pre-Cambrian age and are regarded as typical instances of primary eruptive ore that has thrust up as glowing masses of lava flow between two somewhat older beds of porphyry. Apparently the ore and the porphyry became segre. gated from common parent magmas by a process of differentiation. Despite the fact that the Kiruna orebody belongs to the earliest pre-Cambrian formation, it has been influenced to an unusually small extent by later metamorphosisms, apart from its having been set on edge through folding and wrenching off by a number of later faults. The Kiruna ore occurs along a stretch of more than 4 miles as a series of slabs or lenses sloping steeply toward the east and sandwiched between two beds of porphyry. The main orebody has a length of about 3 miles and an average width of 300 ft with a maximum of 600 ft. The dip varies from 65" to 45" toward the east and the known depth is 3000 ft, although magnetic surveys indicate it may be at least 6000 ft. Malmberget has undergone a more thorough transformation, having been pressed and crumpled into a meandering band of disconnected layers and lenses. The largest of the more connected bodies of ore, the Great Ore Layer, outcrops on a low mountain ridge and has a total length of about 4 miles and a maximum width of about 300 ft. The dip varies from 30" to 70" towards the north. The main orebody in Grangesberg, the so-called

Jan 1, 1953

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"This paper briefly summaries the status of a recent program aimed at identifying new chemistry for use as sulfide mineral frothers and collectors. The background motivation and planning behind this work is given along with the general families of chemical structures synthesied and studied in detail followed by typical flotation application results in various laboratory and plant scale tests. Flotation testing to date has been very encouraging with often improved recoveries of certain minerals and improved pyrite selectivity being observed over commercially available reagents. In addition, in some cases, the dosage and lime requirements of these new collectors are significantly less than that associated with standard sulfide mineral collectors. INTRODUCTIONFroth flotation is one of the most widely used and economic means of concentrating metal sulfide ores. There are numerous reference books that have been published on the chemical aspects of flotation [e.g., ref. 1-7] which are based on studying the influence on selected minerals of chemical structures that have been used commercially for many years. In fact, almost 98% of the volume of flotation collector and frother reagents used at the industrial level today were known and manufactured in some form 25 years ago [8]. There are many reasons for this lack of significant new flotation reagent development [9] including the general utility and relative cheapness of existing collectors such as xanthates and existing frothers such as the alcohols and glycol ethers. Another reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials. This environment makes reliable reagent comparisons difficult and seriously limits the use of theoretically based chemical structure studies to predict new or optimal reagents. In addition, the higher cost of specialty flotation reagents demands that their performance attributes be significantly greater than that achieved with existing all-purpose commercial reagents - something often difficult to prove in practice."

Jan 1, 1988

By George A. Takach

The U.S. Bureau of Mines is conducting research with the goal of automating underground coal mine roof bolters for greater mine safety. In the project described here, the Bureau has focused on automating the drilling portion of the drilling and bolting cycle. A drill monitoring system designed and developed by Parvus Corp. of Salt Lake City. UT, was placed on a Bureau model roof- bolting drill. The drilling parameters of torque, thrust, rotation rate, penetration rate, and position are monitored through sensors connected to an asynchronous, control-oriented local area network (LAN) that communicates with data-accumulating and data-processing nodes. By placing microprocessors at the two data nodes and at the valve control nodes, and combining these nodes with a personal computer (PC), the monitoring and control system can achieve parallel processing capabilities. Such capabilities are referred to as locally intelligent distributed processing. Only data that have changed significantly are reported through the LAN to a supervisory control and data acquisition (SCADA) system mounted on an IBM- compatible 80286 PC. The SCADA system displays the values of the drilling parameters and calculates the specific energy of drilling, which is then used as an indicator of the type of rock being drilled. Besides monitoring the drilling process, an operator at the computer can control the rotation and thrust of the drill from a remote location through the SCADA program and can set drilling parameters on the basis of observed values of the specific energy of drilling.

Jan 1, 1992

By Arthur F. Taggart

IN 1900, Elmore found that if an acidulated pulp was stirred up. with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from-the gangue-what today is called collection-and second, to buoy the collected sulfide away from the gangue.. The action in collecting is illustrated by Fig. 1, which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids, we consider the oil and water fixed and the solids presented, to the surface of contact, the condition will be as shown in Fig. 2; the. sulfide tends to. be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them, there. GAS As BUOYANT MEDIUM OF FLOTATION In 1906 Sulman, Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Froment, DeBavay, Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To. all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. But they placed on the oil an additional burden; viz.: froth-making, and it soon became apparent that not. all oils were suitable for the dual purpose. As a matter of fact, it is probable 'that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928

Stressed steel cables, similar to those used in pre-stressed concrete, have been used for rock mass reinforcement, in civil engineering, for many years. This type of reinforcement has been attempted for open pit wall support, on several occasions, but has never gained wide acceptance as a practical approach because of high cost and complexity of installation in a mining environment. On the other hand, untensioned, fully grouted cable dowels (cable bolts) have gained wide acceptance for ground support in underground mining and it is perhaps surprising that this technique has not been used to a greater degree in open pit mining. The first systematic application of this technique in Australia was at the Mary Kathleen uranium mine in 1976, where it was spectacularly successful in maintaining steep stable walls in a jointed rock mass with unfavourably dipping structures. Cable bolting, and other techniques, are now being used to an increasing degree for wall support in both small and large open pits, for two basic applications: 1. stabilisation of potentially unstable sections of a wall, or 2. to allow steeper walls and reduce waste stripping volumes. In virtually every situation, wall rein- forcement has significant economic as well as technical advantages. The paper describes the development of the techniques, the mechanisms of wall support, the methods used, and discusses several case histories of its application to Australian open pit mines.

Jan 1, 1986

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By H. R. Barnhurst

IT would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Doubtless the crossing of the sticks of wood in building a, wood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets utilized metal bars as supports for the same purpose. It is probable that Tubal Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in east iron, grate bars cane in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a. natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deficiencies in its primary development, and within that tine there has been great advancement in the means of producing initially fire of high efficiency, so that to clay we are moving rapidly toward loth high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to Min nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for raking what was at best a, very imperfect pulverization of the coal, and the expense of preparation was very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 10, 1913