Search Documents

By Donald J. MacNeil

THE opinion, based upon geological knowledge, that certain areas within the Province of Nova Scotia might yield commercial quantities of petroleum, is not new. It dates back to at least 1864, when the Pioneer Oil and Salt Company drilled some shallow holes in search of oil near lake Ainslie, Cape Breton. As a matter of fact, several companies were engaged in oil exploratory work near lake Ainslie at about that time; included among them were the Inverness Oil and Mining Company, the Victoria Oil Company, the American Oil Company, and the Cape Breton Oil and Mining Company. Oil exploration by these and other companies was conducted sporadically on Cape Breton island until 1914. In several instances, the depth of the test holes exceeded 1,000 feet; the deepest was carried to 3,260 feet. The Lake Ainslie area was selected because oil seepages were present along certain sections of the lake shore, but the tests that were drilled to tap the oil-bearing zone failed to yield anything of commercial value. Currently, there are three areas in Nova Scotia wherein active exploratory work is being conducted, namely, at Pugsley Siding close to Amherst; at Kennetcook, Hants county; and near Mabou, Inverness county. The Pugsley Siding test is being drilled by the Sun Oil Company, of Philadelphia; the work at Kennetcook is under the direction of the Nova Scotia Oil and Gas Company; two relatively deep holes were drilled by the Lion Oil Refining Company in 1944 near Mabou, and, as a result of the additional geological information derived therefrom, another test probably will be drilled by this Company in the same area. Aside from these activities in the search for petroleum, the oil possibilities of several other sections of the Province are being studied by means of surface geological mapping.

Jan 1, 1945

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By T. Kontos

Rogers Group, Inc., is the nation's largest privately held aggregates producer (primarily producing crushed limestone and secondarily sand & gravel) and a major regional asphalt paving construction contractor. The company also has interests in building supplies and coal. Facilities are concentrated in five states in the central U.S. (Ohio, Indiana, Kentucky, Tennessee, and Alabama), with an additional location in Southwestern Virginia. At the request of its then CEO and with support from the company's ownership, Rogers embarked on a strategic planning program in late 1986 by retaining an outside management consulting firm. The ultimate goal of this program was to develop a self-sustaining strategic planning process to inject a strategic dimension into every manager's business thinking and to improve company performance. Since then, Rogers has internalized the outside consultants' strategic planning framework --initially, using it wholesale, and later, greatly streamlining and tailoring both the planning process and product to meet the specific needs of the company. Implementation of strategies developed from strategic planning has resulted in significant improvements throughout the organization. The latest product of the strategic planning effort is a company-wide (or, "corporate") strategic plan that carries the theme of "Market Leadership through Excellence". This paper provides a case study of successful corporate strategic planning by examining the evolution of strategic planning at Rogers and by summarizing the key elements of a sound planning process and product.

Jan 1, 1994

In its largest product launch in company history, Cummins Engines welcomed more than 200 customers, vendors and media to witness the unveiling of its new QSK95 engine at its Seymour Engine Plant in Seymour, IN on Nov. 1. It took the efforts of 150 engineers to design the QSK95 and more than $100 million in investments to establish a new production line and test facility at Cummins? Seymour Engine plant. The result of these efforts is a new platform of engines that Cummins says will provide as much as 2,983 kW (4,000 hp) and will be the most powerful, high-speed diesel engine ever built.

Jan 1, 2012

By Norris E. Brooks

MAPCO Inc. is an integrated energy company involved in oil, gas, gas liquids, pipelines, and coal. The Coal Segment has installed a simple incentive program based on profit, tons produced, and hours worked at each operation. The plan has two segments-production bonus and profit sharing. Each segment is described and the results, which include high productivity, good safety, and high morale are discussed.

Jan 1, 1983

By G. A. Campbell

This paper considers the international market trends of the rare earths and how they are strongly influenced by the by-product/co-product nature of their mining and processing. The two main economic minerals for the rare earths are bastnasite and monazite. Monazite is primarily a by-product of mining ilmenite and rutile and is affected by changes in these markets as well as the presence of thorium. Bastnasite is a by-product of mining iron ore in China and a stand-alone product in the USA. The paper will use conceptional relationships and empirical data to delineate the various by-products/co-products relationships and how they determine observed international market behavior.

Jan 1, 1996

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By Travis A. Davidson, Ralph E. Burnham, Cathy Aimone-Martin, J. Kelly Ratliff

Blasters face a long list of tasks to execute daily—from vehicle inspections to blast design and layout, hole loading and tie-in, securing the site, and finally, safely executing the blast. Good practices and, in most cases, regulations and requirements necessitate documenting their work, specifically their blast report. While some blasters use paper forms, others use electronic means to streamline the process. The authors have served as attorneys and expert witnesses in representing companies and individual blasters in numerous administrative and legal matters in which documentation of the blaster’s work was both critical and detrimental to the effectiveness of defending their work. This paper discusses in a case-study manner the authors' observations concerning good blast report format, specific observations around electronic and paper report completion, record-keeping, seismograph setup and recordkeeping, video and photo documentation, internal auditing, and other topics related to documenting the blast. The paper aims to serve as a discussion guide for blasters to improve their blast record-keeping process, develop better practices that effectively document their work, and allow them to defend their work should a claim arise concerning their operations.

Jan 21, 2025

By B. Hyatt, E. Klokholm

The reesistivity of Cu-Pd alloys of 9.6 to 29 pct Pd alloys was measured after plastic deformzation in tension. For all compositions a continzting decrease in resistivity with increasing plastic strain was observed. By comparison with the results of Damask on a brass ad Cu3Au, it was deduced that these anonzalous decreases in resistivity are due to the decrease in short-vunge order caused by cold work. An anomalous decrease in the resistivity of cold-worked CU-Pd alloys was first reported by Jaumot and Sawatzky.' They observed decreases in the electrical resistivity when disordered Cu-Pd alloys drawing at room temperature. Recently, a similar anomaly was reported by Aarts and Houston-Mac-Mi1lan2 in Ag-Pd alloys containing 10 to 45 pct Pd. The plastic deformation in this case was produced by tensile strain at liquid-nitrogen temperatures. For AE-Pd alloys the relative resistivity change becomes positive for tensile strains of about 20 pct.

Jan 1, 1960

By Vincent T. Ricca, Kurtis Chow

When dealing with acid mine drainage as to treatment levels, costs, and evaluation of abatement schemes, predictions of the quantity and quality of the discharges are needed. An acid mine-drainage model is presented in this paper. In essence, the model is a hybrid of computer programs for stream flow simulation and acid mine drainage. Two major aspects of the model are discussed: mine-water generation and acid-load production. The former is based on hydrologic concepts and the latter on pyrite oxidation kinetics and oxidation product removal. The total model is programmed for the high-speed digital computer. The major inputs are: climatological, basin characteristics, and mine characteristics data. By the use o f the hydrologic model the amount of water that flows through the pyritic system is determined. From this information, acid loads removed by leaching, inundation, and gravity diffusion are then predicted. The outputs from the total model are: average daily mine-water discharge, the associated acid concentration or load, plus the average daily flow in the receiving streams or at basin outlets. The capabilities of the separate models have been tested individually and the joint model has been applied to a small drift mine in southeastern Ohio.

Jan 1, 1975

By Osvaldo A. Bascur, Curt Heftier

The lack of integrated information including the Energy/Utility Suppliers with sufficient detail for analysis causes inefficient operation in metallurgical complexes including the Energy/Utility Suppliers . Defining the right context for information use is essential for sustainable operations. This being said, what are we doing to enable people to act upon information and to be aligned to optimize the use of resources like raw materials, energy, water and consumables for an entire metallurgical complex? Collaboration between all company entities is a key component of improving efficiency. Evolution of web technology and object modeling of enterprise assets enables collaboration across the whole business. Operational troubleshooting occurs more quickly as the organization acts on issues to reduce wasteful operation. This paper presents a real time software infrastructure with tools that give users the ability to sift through available data, transform data into information for business continuous improvement and optimization. We will introduce a new technology for analyzing real time data, information and events using multidimensional analysis of information to detect anomalies based on the statistics of the data classified by time events to reduce the information into action. A new paradigm for collaboration at a local and strategic level is proposed to enable the enterprise to become proactive in dealing with wasted time and products. Three examples from the industry will presented and their benefits highlighted.

Jan 1, 2011

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By Francisco Contreras

El sistema electrohidráulico es una alternativa económica para reemplazar sistemas neumáticos y operar una instalación nueva en el accionamiento de las compuertas de carguío; con un costo mínimo en el consumo de energía eléctrica, si está constituido por los componentes debidamente dimensionados. En el presente trabajo se detallan tales componentes, así como el procedimiento de aplicación de la mecánica de fluidos en ingeniería (principio de Pascal); lo que permite transmitir grandes fuerzas utilizando pequeños elementos constitutivos, y realizar maniobras de mando y reglaje con facilidad. Dado que una bomba hidráulica movida por un motor eléctrico es capaz de desarrollar esfuerzos enormes aprovechando la sección de cilindros, esta tecnología tiene un amplio potencial de desarrollo. Con un solo equipo de poder se pueden operar independientemente las tolvas que sea necesario maniobrar en distancias de hasta 500 metros con telegobierno por mando eléctrico. Puede aplicarse en piques, rampas, galerías, cruceros, etc.

Dec 31, 2017

By Pieter de Waal

The beneficiation equipment under the control of plant metallurgists exploits the differences in the physical properties between valuable and waste mineral components. In many cases, laboratory results are too late for process control and can only serve the purpose of "post" reports, the calculation of a mass balance and the issue of a quality certificate. As a result, experienced operators regularly adjust separation equipment based on the colour and texture of the various product streams in the beneficiation plant. Metallurgists quickly learn to recognise the different minerals in their ore body. The stereo microscope has been a valuable tool used by operators to quantify known mineral species. For many years it was the only practical method available for the purpose of process control and even for quality contro1. The modem spectroscope is far superior to the human eye and can rapidly detect a change in mineral composition. New generation optical scanners and digital signal processors can provide useful signals, related to mineral composition that can readily be applied for the purpose of process control. Successful case studies, covering dry in-line and slurry applications as well as in-plant fast spot analysers are presented.

Jan 1, 2014

By Augusto Cabrera La Rosa

Jul 20, 1956

By Frank G. Breyer

C ONDITIONS have not been favorable for new developments in any line. It has been a period, how- ever in which recent developments have been subjected to the severest tests. Those which have been able to hold their own in the severe competition of 1932 must be considered fully proved commercial processes. The continuous vertical-muffle retort plant at Palmer- ton is reported to have been in operation at practically full capacity throughout the year. The high quality of metal produced and the low operating costs are factors which have kept this plant running when many of the older furnaces were shut down. The plant at Meadow- brook, W. Va., is also reported to have been in steady operation throughout the year. Average retort life is said to be better than two years with about three-quarters of the original retorts still in operation after 2 ½ years.

Jan 1, 1933

By André Tarcizo de Oliveira Vieira

A Companhia Siderúrgica Nacional (CSN) gera diversos resíduos metálicos de diferentes granulometrias que não podem ser utilizadas na rota natural da produção do aço. Este trabalho tem como objetivo descrever o pioneirismo do desenvolvimento e a implantação de melhorias no sistema de adição em carros torpedos que permitiram a utilização nobre de resíduos ricos em ferro, demonstrando a viabilidade técnica assim como a viabilidade econômica. A redução do consumo de energia é outro argumento para reciclagem de resíduos, neste contexto a CSN tem aumentado o interesse pela reciclagem devido a necessidade de diminuição de consumos energéticos e da consciência ambiental. O processo desenvolvido demonstrou a viabilidade da utilização de metálicos de pequena granulometria pela adição em carros torpedo, aumentando a oferta de ferro gusa líquido para os convertedores da CSN.

Aug 2, 2018

FEB. 17-The past month found the average citizen backed off just a little more into his blind corner staring glassily at hydrogen bombs, unbalanced budgets, John L. Lewis, more inflation, a rising wave of strikes, the country's only active battleship on a mudbank, a famous scientist in gaol as a traitor, a favorite actress on a Roman holiday, and rising mountains of potatoes, butter and eggs begging for destruction. About the only bright spot has been industrial activity and employment, but even these are menaced by the coal shortage. Most industries have orders on hand or in prospect to warrant high operations for some time to come. The trend of the Reserve Board's production index is upward except as strikes may interfere. There has been heavy buying at the seasonal merchandise shows, particularly in furniture and house-hold goods. The demand for goods of this kind illustrates greater confidence in the Spring outlook than was generally felt a year ago. Further, the demand also reflects improved market positions due to curtailment of output and reduction of inventories in 1949 and sustained consumer buying power. It demonstrates the strong support that is given directly to many businesses, and indirectly to all, by the phenomenal construction activity that is now under way. The Commerce Department places the number of new dwelling units started in 1949 at the new all-time high of 1,019,000.

Jan 3, 1950

By Verônica Scarpini Candido

O conhecimento das características microestruturais de materiais utilizados como constituintes mássicos de cerâmica vermelha é de grande importância para a compreensão das propriedades das peças queimadas. Assim, este estudo tem por objetivo caracterizar microestruturalmente a escória granulada de aciaria proveniente de uma siderúrgica do estado do Pará visando a sua incorporação em argilas para produção de peças de cerâmica vermelha. O resíduo passou pela etapa de beneficiamento e, depois, foi realizada a difração de raios-X (DRX) e fluorescência de raios-X (FRX). Além disso, realizou-se também a análise morfológica por microscopia eletrônica de varredura (MEV). Os resultados mostraram que hematita, magnetita e wustita são as fases predominantes associadas aos óxidos de ferro. A análise química por FRX mostrou que o resíduo apresenta baixos teores de sílica (SiO2) e alumina (Al2O3), associados a elevados teores de óxidos de ferro e óxido de magnésio. Dessa forma, a caracterização da escória granulada de aciaria mostrou que esse resíduo apresenta-se como um potencial constituinte mássico cerâmico podendo contribuir para a formação de fase liquida durante o que acarretaria em melhoria das propriedades tecnológicas como absorção de água e resistência mecânica.

Oct 30, 2017

By E. Bonates

Dispatching systems have attracted considerable attention in the last years due to substantial gains in productivity achieved through their implementation. These systems will be extensively used in the future by mine operators as a means of optimizing productivity. This paper describes a computer simulation model designed to study the feasibility of continuously dispatching trucks in open-pit mines based on different operating procedures. The system developed is semi-automated and performs an active role by suggesting to the dispatcher the best assignment according to each specific circumstance. It is modeled based on an advance-clock increment to reduce computing time and allows the insertion of heuristic dispatching policies and equipment real-locations when breakdowns occur. Dispatching procedures taking into account long-term production objectives are considered in system development.

Jan 1, 1988