Search Documents

By D. S. Ramey

In-situ leaching of the oxidized copper mineral resource at the San Manuel mine has proven to be a technically and economically viable method of copper extraction. Although this leaching method has been modeled to predict future production capabilities, the expected magnitude of the ultimate recovery from any portion of the present mine is not fully understood. A closely controlled test has been designed, constructed, and is now operating to determine the rate and magnitude of copper recovery. The test, initiated in June 1992, is scheduled to operate for approximately 18 months. This paper presents an overview of the test design and current results.

Jan 1, 1993

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982

By S. Ramachandran, R. G. Woolery

INTRODUCTION Union Carbide is currently operating an in-situ leach project on the Palangana Dome area in Duval county. This deposit meets all the requirements for in-situ leach in that the ore (1) is below the water table, (2) is in a permeable horizon, (3) is amenable to chemical leaching, and (4) is confined by impervious layers. This project has been under commercial production since 1976, and its capacity has been expanded on three occasions since going on-stream. Recently, additional uranium reserves were discovered on the Rogers-Cardenas (R-C) property about 32 km north of the Palangana operation. The ore is located within the Oakville sands and its characteristics are quite similar to those of the ore at Palangana. Both are an unconsolidated Arkosic sand high in clay and calcium carbonate. The R-C ore, however, is somewhat coarser with a mean particle size of 0.15 mm as compared to a mean particle size of 0.07 mm for the Palangana ore. In all respects it would appear that this ore would be a candidate for in-situ leach as a satellite operation to Palangana. Unfortunately, R-C ore is above the water table and, therefore, not amenable to the Palangana practice. Because of the limited known reserves in this deposit, it is readily apparent that conventional mining and milling are out of the question. However, because of its proximity to our Palangana operation, it seemed worthwhile to consider other options. The most viable route based on our past experience was to heap leach the ore. Our recent success at our Gas Hills facility and our Maybell operation, in employing a heap leach practice to our marginal reserves seemed to be a logical approach for processing this ore. Our experiences at both locations are described in "Heap Leaching - A Case History" by R. G. Woolery et al., Mining Engineering, March 1978. In both instances the process is an acid leach circuit and acid consumption averages 20 kg/t H2SO4. A preliminary feasibility study showed that because of the high strip ratio required for the R-C project to be successful, additional ore reserves must be located and that a method of heap leaching with an alkaline circuit would have to be developed. As a result of this paper study, the decision was made to proceed with a program of additional exploration drilling to determine the total ore reserves that could be mined economically. The Mining Department will evaluate each ore zone for cutoff grade, strip ratio, and expected mining cost. At the same time, a laboratory program to evaluate the available core samples for amenability to heap leaching with respect to an estimate of uranium recovery and processing costs was developed. This program is currently in progress, and at this time, we are just completing our process amenability study. BENCH-SCALE EVALUATION OF THE R-C ORE The initial bench-scale slurry leach tests on the R-C ore showed an acid consumption in excess of 200 kg/t H2SO4. These data, of course, discouraged us from considering this process route. Not only would the acid cost be prohibitive, but the gypsum generated by the reaction of the sulfuric acid with the calcium carbonate of the ore would severely effect the percolation of the lixivant. For this reason, the laboratory program was directed toward an alkaline circuit compatible with heap leaching. Because of the proximity of the R-C property to our Palangana operation, it seemed advisable to integrate the processing of this ore into the production at Palangana. Doing so would enable us to bring the R-C property into production by merely enlarging our present facilities at Palangana; otherwise, construction of a grass roots plant would be necessary. Ideally, the simplest method would be to construct the heaps at Palangana and employ an ammonium carbonate/bicarbonate leachant compatible with the in-situ production liquor. The product liquors could then be co-mingled or processed separately as desired. To determine if this goal was practical, samples of the R-C ore were obtained, and a laboratory program initiated. Heap leach amenability testing consisted of preliminary bench-scale evaluation to determine optimum solution strength and ultimate uranium recovery, followed by small column tests to confirm the bench-scale metallurgy and to determine percolation characteristics. These bench-scale tests are being followed by pilot-scale testing approximating field conditions. As expected, the bench-scale tests showed that the dissolution rate is considerably slower for alkaline leach than has been our experience in acid leaching. Because of the slower reaction rates, product liquor grades will be lower than for acid, as greater volumes of solution are required for satisfactory uranium extractions. The greatest influence on reaction times found in the laboratory was the carbonate/bicarbonate strength and oxidant addition. However, the higher salt concentration reduced the efficiency of the IX resin circuit and about 25g/L salt proved to an upper limit compatible with subsequent IX treatment. The oxidant contributed significantly to the early extraction rate but seemed to have only minimal effect on the total practical U308 extracted or the time required to achieve it. This variable will require larger scale testing to determine if the added cost of the oxidant is actually justifiable. Thus, the small-scale laboratory slurry tests, based on the 0.088% U308 sample available, indicate that leaching at 25g/L ammonium carbonate/bicarbonate, with or without oxidant, we might expect an 80-85% U308 extraction on this ore.

Jan 1, 1979

A. R. Ledoux,New York City: The so-called combination method " is generally used in assaying bar copper for silver. It has been modified from time to time. Briefly outlined

Jan 1, 1901

By C. E. Johnston

In December 1956, International Minerals & Chemical Corp. installed a rope-suspended belt haulage system in its Carlsbad, N. M., potash mine to complement the already existing rail transport arrangement. In this article the author describes when and where each system is used, the advantages and disadvantages of both, and future planning and proposed changes in haulage at IMC. The haulage system at the International Minerals & Chemical Corporation (IMC) potash mine near Carlsbad, N. M., reached a turning point in December 1956 with the introduction of rope-suspended belt haulage. In fact, IMC pioneered the use of this type of belt in the potash industry. Since that time belt conveyance has been employed as an extension of the rail system but not as a replacement of the main rail haulage. IMC's potash mine is located in the Permian Basin, approximately 20 miles east of Carlsbad in Eddy County, N. M. The 800, 850 and 900-ft levels have been exploited. From these levels over 60 million tons have been extracted. The two ore minerals are sylvite (KCl) and langbeinite (K2SO4. 2MgSO4). The principal gangue mineral is halite, with minor amounts of polyhalite, kainite and leonite. Langbeinite is mined on the 850-ft level and sylvite on the 900. The 800-ft level, with both langbeinite and sylvite mineralization, is idle. Mining heights vary from 54 in. to over 10 ft. A room and pillar mining system is used. Geologically, mining is done in the Salado salt formation. The U.S. Geological Survey has classified the 900-ft sylvite level as the first ore zone and the 850-ft langbeinite level as the fourth ore zone. Since the grade of sylvite is low, mineralization at the IMC mine is somewhat irregular and salt horses, are common. Selective mining and a flexible haulage

Jan 1, 1963

By Murl R., Schrock

THE use of diamond-drill holes at the Moctezuma Copper Co., Pilares mine, Pilares de Nacozari, Sonora, Mexico, for the ventilation of raises has resulted from experiments that were made in an effort to secure continuous and efficient ventilation in hot and gaseous raises. The method is particularly applicable in long raises and in raises run from development levels where the source of fresh air is distant. In order that the CO, concentration shall not become excessive, 30 cu. ft. per min. per man must be supplied to a heading for breathing purposes:' The quantity of air that will pass through a diamond-drill hole by

Jan 1, 1929

By AIME AIME

A STUDY of subsidence and ground movement in the copper and iron mines of the upper peninsula of Michigan has been made by W. R. Crane of the United States Bureau of Mines and published as Bulletin 295 of 66 pages and 49 illustrations. As a result of subsidence, the country adjacent to the mines and over- lying the mine workings in this district is often broken to such an extent as to affect its value; mine shafts and development openings are occasionally so damaged as to be rendered useless, and water can enter the workings through fractures and cave-ins. The problem is more serious in the iron-mining districts, where villages and towns not owned by the operating companies have grown up around mining operations.

Jan 1, 1929

By W. Hu

Gravity concentration has been the main method for tin ore beneficiation, based on the significant difference of density between cassiterite and gangue in the tin ore. However, with the exhaustion of rich and coarse reserves, the proportion of tin distribution in slime be-comes as high as 50 to 70% and has a size range of -19 urn. In some sulfide tin ore, most of the tin is of the minus 10-urn size fraction, and thus slime processing has gained importance in tin ore processing. Some innovations are being developed, such as the centrifugal cone separator, belt concentrator, slime table, B-M separator, and slime flotation. Direct flotation with tolyl arsonic acid has been practiced with success.

Jan 1, 1989

By B. B. Sandiford

It has been known for many years that the efficiency of a water flood can be improved by lowering the water-oil mobility ratio in the system. Such a change leads to better sweep efficiency and also to more efficient oil displacement in the swept zone. Data from our laboratory water-flood tests of both small cores and long sand packs are presented which show that water mobility can be reduced and oil recovery increased by the addition of certain polymer solutions to flood water. The reduction in mobility, in many cases, is greater than would be expected from conventional viscosity measurements. These solutions, however, do not cause significant reductions in oil mobility. The over-all effect of these mobility changes is increased waterflood oil recovery. Encouraged by results of our laboratory work, we expanded our study to include pilot field tests of floods with such solutions. One such test, made in the West Cat Canyon field, Santa Barbara County, Calif., is described in detail in this paper. Three other field tests are also discussed. INTRODUCTION Oil production from most reservoirs following primary depletion and/or water flooding is often less than 50 per cent of the original oil in place. Heavy oil reservoirs seldom yield over 15 per cent of their original oil. With new reservoirs becoming harder to find, the improvement of oil recovery efficiency is one of our very important problems. We describe here some of our attempts to increase the efficiency of oil displacement by adding a water-soluble polymer, partially hydrolyzed polyacrylamide, to flood water. This technique will be termed "polymer solution flooding". The concept of using high-viscosity water to increase the efficiency of water flooding is not new. In 1944 Detling (Shell Development Co.) obtained a patent covering the use of several additives for viscous water flooding.' His objective was to improve water-oil mobility ratios by increasing the viscosity of the flood water. Other patents2-27 have been granted covering specific water-SO~LIble polymers or specific conditions of viscous water flooding. Barnes'" described his laboratory model study of the injection of a viscous water slug into a reservoir which had been partially invaded by bottom water. He concluded that, for this type of reservoir, "the cost of viscous water should not exceed a few cents per barrel for viscous water slug injection to be economically feasible" Our studies have led us to a somewhat different conclusion in a number of cases where hydrolyzed polyacrylamide solutions have been injected into reservoir models or actual reservoirs. Possible reasons for this difference are discussed in this paper. Our studies have shown that polymer solutions may lead to an increase in oil recovery over that from an ordinary water flood by (1) improving sweep efficiency, (2) improving microscopic displacement efficiency, or (3) a combination of these mechanisms. In the work of Barnes, only the benefit of improved sweep efficiency was considered. Also, our work has shown that there are marked differences in the effectiveness of different water-soluble polymers as flood water additives. Partially hydrolyzed polyacrylamide is better than many other water-soluble polymers we have tested because, even in very low concentrations, it can lead to increased oil recovery. This is an important advantage when either a dilute polymer solution is injected continuously or a relatively concentrated slug is injected followed by water. In the latter case! portions of the slug become diluted and function in the formation as very dilute solutions. As dilution takes place the effective slug size will increase which, in turn, will reduce the cost per barrel of the effective flooding medium. The reason that partially hydrolyzed polyacrylamide solutions are more efficient at low concentrations than certain other polymer solutions of equivalent viscosity (when measured in conventional viscometers) is not fully understood. We do know that the shapes and sizes of macro-molecules dissolved or suspended in liquids influence the flow properties of their solutions or suspensions. Solutions of partially hydrolyzed polyacrylamide cause greater reductions in water mobility than would be expected from conventional viscosity measurements. LABORATORY STUDIES Laboratory water floods were run in linear and radial systems with different water-soluble polymers and under varying conditions of flow. including reservoir conditions of temperature, pressure and fluid composition. Some of these runs are considered in this section. OIL DISPLACEMENT IN LINEAR MODELS In this group of runs the sweep efficiency approached 100 per cent because the linear sand packs used were as nearly uniform as possible. Results reflect primarily the micro-scopic displacement efficiencies. The laboratory models were unconsolidat-ed sand packs the lengths of which varied from about 4 in, to 40 ft. Further information on the flow models used is listed in Table 1. Using conventional procedures, water floods were run on sand packs containing either refined or crude oil at restored state. Frequently, a repeat run, similar to the first, was made as a check. Then a third run was made on the restored-state model using either polymer solution or a combination of polymer solution (slug) and water. Details of these runs are also reported in Table 1. In Figs. 1 and 2 results of two different groups of runs are shown in which the oil used was a 62-cp refined oil and the flooding medium

Jan 1, 1965

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988

By Carle R. Hayward

ATHOUGH there are signs of improvement in the lead industry, conditions are still far from what we have been accustomed to call normal. There has been little to stim¬ulate research and those responsible for the finances of the companies have been inclined to discourage expenditures except where need was urgent or the prospect for immediate returns bright. In spite of this fact, improvements have been developed here and there which will be available as business conditions become adjusted. No publicity is allowed at present. The rising price of silver has had a tendency to increase the production of lead from argentiferous ores but the greatest interest continues to be in the secondary field. Practically all lead plants situated near large centers of population are treating scrap materials, particularly battery plates, the quantity of which is increasing with the improvement in automobile sales.

Jan 1, 1936

President MRS. HARRISON SOUDER Smith Paramus Road Ridgewood, N. J. First Vice-president MRS. ROBERT HURSH 10 Kilburn Road Belmont, Mass. Second Vice-president MRS. ERLING L. JORGENSEN 95 Knollwood Rd. Short Hills, N. .1. Third Vice-president MRS. PERCY E. BARBOUR 1R(; Riverside Drive New York, N. Y. Fourth Vice-president MRS. C. B. MURRAY 2040 Stearns Rd. Cleveland, Ohio

Jan 1, 1938

By James Terry Duce

Production of oil in Bahrein for the war years was as follows: YEAR BBL PER YEAR Prior to 1939 . . . . . . . . . . . . . . 22,287,055 1939 . . . . . . . . . . . . . . . . . . . . . . 7,588,554 1940 . . . . . . . . . . . . . . . . . . . . . . 7,073,919 1941 . . . . . . . . . . . . . . . . . . . . . . 6,794,157 1942 . . . . . . . . . . . . . . . . . . . . . . 6,240,627 1943 . . . . . . . . . . . . . . . . . . . . . . 6,571,609 1944 . . . . . . . . . . . . . . . . . . . . . . 6,713,795 1945 . . . . . . . . . . . . . . . . . . . . . . 7,308,938 Total to Jan. 1, 1946 . . . . . . . . 70,578,654

Jan 1, 1946

By R. C. Wallace

In the early explorations of the Northwest, the search for minerals played a not inconsiderable part. The first episode had its disillusioning sequel. Sir Martin Frobisher, in 1576, sailed up that bay in Baffin land now known as Frobisher bay, thinking that he had the coast of Asia on his right hand. He brought back from this expedition a piece of 'black earth' from Hall island, from which an alchemist by coaxing nature, or his own conscience, obtained gold. A second expedition of three ships was fitted out in 1577, and a third of fifteen ships in 1578. The ships were loaded with this 'black earth', which on subsequent investigation was found to be worthless, and interest in minerals for the time being ceased. In 1612 Hall and Baffin went in search of a gold mine near the Arctic circle on the west coast of Greenland, reported to be worked by the Danes. They found old workings, but no ore. To come nearer the Hudson Bay area, it is noteworthy that the charter granted by Charles II to the Hudson Bay Company in 1670, as a result of the explorations of Radisson and Groseillers, was given "-in consideration for their having at their own cost and charges undertaken an expedition to Hudson bay in the northeast parts of America, for the discovery of a new passage to the South sea, and for the finding of some trade for furs, minerals and other considerable commodities, and of their already having made by their undertakings such discoveries as did encourage them to proceed farther in pursuance of the said design, by means whereof there might probably arise great advantage to the King and his Kingdom - ".

Jan 1, 1925

By W. S. Morris

THE East Texas oil field is the largest in the United States and perhaps the largest 'in the world ; likewise, it is one of the most interesting. The East Texas oil field is a water-drive field. Small amounts of salt water were produced from wells on the western side of the field from the bt-ginning of the development. By the end of 1933 (the field having been discovered in September 1930) water production had reached 9000 barrels per day. By the end of 1936, approximately 2000 wells were producing about 45,000 barrels of water per day, and the problem of salt water disposal attracted the serious attention of the operators. Salt water production in the field has steadily increased and today approximately 450,000 barrels of water per day is produced while the oil production averages about 375,000 barrels. The disposal of this salt water has therefore become one of the major operating problems. Various methods of salt water disposal have been tried in the East Texas field. Evaporation in open pits proved

Jan 1, 1944

By AIME AIME

THE petroleum economics session," held on Wednesday morning, Feb. 20, 1929, presided over by Campbell Osborn, chairman, proved to be of un- usual interest and resulted in serious and constructive discussion of the papers presented. The first paper on the program, "Gasoline Economics and Refinery Operation," was by H. J. Struth, petroleum economist of the Gulf Publishing Co., Houston, Tex. While this paper was intended to cover the re- finery situation, it also presented the author's reasons for believing that the oil producer should give cognizance to gasoline demand as a most reliable barometer by which to parallel the production of crude petroleum. The discussion which followed brought out some interesting points in connection with the immediate outlook for the industry as a whole during the present year. Some advanced the opinion that, regardless of the out- come of proration efforts, the refiner is in a position to conduct his operations on a reasonably profitable basis, provided that he exercises control over them. This would mean running less crude and resorting to wider utilization of cracking to produce the gasoline demand. Thus, if the refiner uses diligent care in scheduling his still runs, the producer will be obliged to carry over a large stock of crude this year, unless he is able to keep production below the limits prescribed by the demand for gasoline.

Jan 1, 1929

By George M. Fowler

EVERY year it becomes more difficult to find new mining districts and new ore deposits. Nearly all of the important discoveries so far can be attributed to surface manifestations overlying the ore deposit. In the future greater skill will be necessary to find ore deposits that give little or no indication of their presence. Mining geology is making progress by broadening its attack upon mineralized regions, by including in its investigations studies of the relation of physical-chemical processes to ore precipitation and various phenomena that heretofore have not always been looked upon as major factors in the problems. Such, for example, are petrographic peculiarities that will help determine structure, aspects of strata or formations favorable or unfavorable to structural deformation or mineralization, and renewed studies of chert and dolomite. This broadening attack is not necessarily being directed to the study of large areas, but rather by doing extremely detailed work in three dimensions in relatively small critical areas to find the key to the structure, reasons for the manner of rock deformation, composition and texture of the rock, and other con¬trolling factors in the larger areas.

Jan 1, 1935

Beverley S. Randolph, Frostburg, Md. (communication to the Secretary): It has always appeared to me that each coalseam has its peculiar character or habit, due to the conditions of its formation, by virtue of which it is either persistent or variable in its section over extended areas. One seam will hold its thickness, chemical character, number and position of partings, beds of slate, etc., over a large area, while another will be found to vary in some of these characteristics every few feet. As the position of the outcrop is an accident of the topography, depending on folding and erosion which have taken place since the bed was formed, no one opening in the outcrop, or, in fact, anywhere else, can supply reliable evidence as to the general character of the seam. To determine the character of an untried seam, a number of sections are necessary from widely separated points, in order to show such variations as may exist. Should material variations be developed, more numerous sections are necessary, in

Jan 1, 1901

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By Paul M. Tyler, Carle R. Hayward

DOES it pay to do really good work? Quite likely the practical millman will answer that it does not. The preparation of ores for market is primarily a business enterprise, and by and large the individual operator does not bother his head about squandering our national resources or making easier the job of the smelterman. Having accepted such ore as he may get fro111 the mine, his job is to make the best possible showing with his mill fro111 the standpoint of financial return. His success is measured in dollars and cents, and he has no rightful reason to expect more than scant acknowledgment of any other achievements from the stock- holders of his company who in the last analysis are his employers.

Jan 1, 1936