Search Documents

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011

By L. T. Sanchez, W. T. Rogers

This paper presents the results of a production experiment evaluating the effect of the use of oxygen in the bessemer converter with respect to its relation to blowing time, amount of steel scrap or cold pig iron which can be melted and teeming temperatures of the molten steel. THE simplest and probably the most efficient and economical means for producing steel from molten pig iron is the bessemer converter. This process is essentially a mechanism for bringing oxygen into contact with the molten metal thereby oxidizing the elements silicon, manganese, and carbon. The source of oxygen is that contained in the air and is limited by that amount. In theory, there is an intermediate chemical reaction due to the mass action of iron and air which is represented by the equation: 2Fe + O2- = 2Fe0 The FeO then becomes the oxidizing agent and reacts with the silicon, manganese, and carbon to produce silicon dioxide (SiO,), manganese oxide (MnO), and carbon monoxide (CO), in the order mentioned. The balancing of the various chemical reactions shows that in the ordinary bessemer process more than sufficient oxygen is delivered to satisfy these reactions, which indicates that a further increase in the oxygen content of the air would serve no useful purpose. In spite of this reasoning, however, it will be demonstrated that when melting stelel scrap, commercially pure industrial oxygen introduced into the normal air blast will permit the melting of a larger proportion of steel scrap than is possible with air alone and also will increase the production rate by a substantial reduction in blowing time. It will also be shown that when melting cold pig iron, it is possible to melt up to twice as much pig iron with the use of oxygen as can be melted without added oxygen with a nominal increase in blowing time. At the plant where this study was made, oxygen is purchased from a nearby supplier and piped directly into the plant. It is supplied to the bessemer converter by being introduced directly into the blast line through an automatic control system which may be adjusted by the bessemer operator or "blower." Normally, iron is supplied by five blast furnaces to an open hearth shop containing twelve 165-ton capacity stationary furnaces and a bessemer converting shop having three 30-ton converters. The molten metal from the blast furnaces is allocated to one shop or the other in a manner to best provide for maximum production. At various times, it is desirable to direct the maximum amount of available blast furnace production to the open hearth shop. This has the effect of reducing the production of the bessemer shop. When this condition exists, it is desirable to supplement the reduced iron charge at the bessemer with steel scrap or cold pig iron to the maximum possible extent in order to maintain high total ingot production. This condition becomes aggravated when one of the blast furnaces is taken out of production for any repair job and particularly for extended periods such as when relining is necessary. The purpose of the investigation and experimentation with oxygen was to determine whether or not it would contribute to increased flexibility in the use of the raw materials, molten iron, steel scrap, and cold pig iron. In addition to the effect of oxygen on flexibility of operation, it was also necessary to determine the relation of its use to production rate or "blowing time," final finishing temperature of the steel or "teeming temperature," and steel quality.

Jan 1, 1953

By Edwin F. Brush, John Chipman

Published data on the activity of carbon in binary and ternary austenite at 1000°C are reviewed. The composition variables are . The coefficient, Vj, has the value for substitutional elements but may be assigned a ualue -1 for silicon to effect a simplification on the mathematical treatment. The activity coefficient PC = is obtained from gas equilibrium data. For the ternary systems studied the Henrian activity coefficient is given by the expression: The principle advantage in cornparison with the analogous expression in terms of atom fractions is found in the fact that for most systems the final term and in many the last two terms are zero. Values of the interaction parameters are tabulated and the graphical comparison of the equation with experirt~ental data is sho,wn in several figures. The thermodynamic properties of the solid solution, austenite, are of considerable importance in the heat-treatment of alloy steels and in other aspects of ferrous metallurgy. Early studies embodied in the Fe-C diagram have been extended to include other binary and some ternary diagrams. Our best hope of obtaining a useful thermodynamic treatment of reactions in complex alloy steels will not be found in quaternary and quinternary phase diagrams but in determinations of activities and interaction relations among the several solute elements. The foundation for such a development was laid by smith' in his early studies of the activity of carbon in Fe-C alloys and his subsequent work on Fe-C-Si, Fe-C-Mn, Fe-C-Ni, and Fe-C-Co solid solutions.2"4 Other observers have also made noteworthy contributions and these will be discussed and correlated here in the light of a somewhat simplified mathematical treatment of solute interactions. Fe-C AT 1000°C In a recent review of the thermodynamic properties of binary Fe-C austenite it was shown that the simple mathematical treatment employed by smith' was capable of describing all the published results on this solution. The treatment utilizes the atom ratio, yc = nC/nF,, rather than the atom fraction. The activity of carbon is proportional to the equilibrium gas ratio, either measured on a scalk in which the activity of graphite is taken as unity or, alternatively, aC may be set equal to yc at infinite dilution. In either case the ratio aC/y = (PC, the activity coefficient. It was found that the experimental data of smith1 and those of Diin-wald and wagner; Bungardt, Preisendanz, and Lehn-ert,' and Scheil, Schmidt, and Wiinnings at temperatures of 800" to 1200° C as well as reliable data on the solubilities of graphite and cementite could be represented by the equation for which graphite is the standard state: The data on alloyed austenite have been obtained at 1000°C. For this temperature, the "Henrian" activity coefficient (which is unity at infinite dilution) is: FOr an interstitial solute such as carbon in austenite it has been shown by statistical mechanicsg that the activity in the infinitely dilute solution is proportional to the ratio of the number of lattice sites occupied by carbon to the number of yet unfilled lattice sites. A variable zz proportional to this ratio serves as a useful measure of concentration:" in which b is the number of lattice sites provided by each atom of solvent; in austenite b = 1. The Henrian activity approaches zz at infinite dilution and the ratio a is the activity coefficient. The effect of a change in concentration is then given by: It has been shown further that in some systems the derivative in Eq. [4] remains constant over a wide range of concentrations. In such a case second-order terms become negligible and the Henrian activity coefficients is:

Jan 1, 1969

By P. M. Blair

This paper presents numerical solutions of the equations describing the imbibition of water and the countercurrent flow of oil in porous rocks. The imbibition process is of practical importance in recovering oil from heterogeneous formations and has been studied principally by experimental means. Calculations were made for imbibition of water into both linear and radial systems. Imbibition in the linear systems was allowed to take place through one open, or permeable, face of the porous medium studied. ln the radial system, water was imbibed inward from the outer radius. The effects on rate of imbibition of varying the capillary pressure and relative permeability curves, oil viscosity and the initial water saturation were computed. For each case studied, the rate of water imbibition and the saturation and pressure profiles were calculated as functions of time. The results of these calculations indicate that, for the porous medium studied, the time required to imbibe a fixed volume of water of a certain viscosity is approximately proportional to the square root of the viscosity of the reservoir oil whenever the oil viscosity is greater than the water viscosity. Results are also presented illustrating the effects on rate of imbibition of the other variables studied. INTRODUCTION The process of imbibition, or spontaneous flow of fluids in porous media under the influence of capillary pressure gradients, occurs wherever there exist in permeable rock capillary pressure gradients which are not exactly balanced by opposing pressure gradients (such as those resulting from the influence of gravity). The importance of such capillary movement in the displacement of oil by water or gas was recognized in early investigations and described by Leverett, Lewis and True in 1942.1 Methods advanced by these authors for studying the process using dynamically scaled models were rendered more general and flexible by the research of later workers.2"4 The influence of capillary forces in laboratory water floods has also been discussed by several authors.6 While imbibition plays a very important role in the recovery of oil from normal reservoirs, Brownscombe and Dyes7 pointed out that imbibition might be the dominant displacement process in water flooding reservoirs characterized by drastic variations in permeability, such as in fractured-matrix reservoirs. In water-wet, fractured-matrix reservoirs, water will be imbibed from fractures into the matrix with a countercurrent expulsion of oil into the fractures. If the imbibition occurs at a sufficiently rapid rate, a very successful water flood can result; if the imbibition proceeds slowly the project might not be economically attractive. Scaled-model studies have demonstrated the vital importance of imbibition in secondary recovery in fractured reservoirs. It is therefore important in the evaluation of waterflooding prospects to develop a thorough understanding of the quantitative relationships of the factors which control the rapidity of capillary imbibition. The imbibition process serves reservoir engineers in still another important way by providing a technique for studying the wettability of reservoir core samples. Such experiments are usually conducted by observing the rate of expulsion of oil or water from core samples submerged in the appropriate fluid. Several papers have been 'published on the experimental techniques involved?? Although Handy has recently published a method for calculating capillary pressures from experiments with gas-saturated cores, it has not yet been possible to deduce quantitative information regarding water-oil relative permeability and capillary pressure characteristics of the rock from the experimental results. Thus a technique is needed for studying the quantitative dependence of imbibition rate on oil and water viscosity, initial water saturation, relative permeability-saturation, and capillary pressure-saturation relations. The development of such information, including saturation and pressure profiles by laboratory experiments, would be very difficult. However, recent advances in the applica-

Jan 1, 1965

By Franklin P. Wood

Unnumbered ages have passed since the time when nature's laboratories were working without the aid of capital or labor unions assisted only by earth's cooling crust and old Sol's rays, to lay the prodigious coal beds of the earth and distil the oils which now furnish the basis for the world's great industries. Strangely enough rays from the same old sun probably somewhat diminished in intensity are still drawing from earth to clouds the water that will run down hill and through man-made devices produce energy to compete with that made with the products created in ages past. So now we find that within the past century vast human industries have grown up around the products of these agencies and here we are today discussing the many problems connected therewith and among the others the subject of this paper, which is essentially the relation of COAL to OIL in industry. The problems involved are those of human relationship and are not fundamentally unsolvable when engineering skill and knowledge is properly applied. The last few years has developed a brand of pessimism that is especially prevalent in the coal industry, at any rate in the west where we come in contact with it. In any general discussion with coal men, a very short time only is required to bring out the feeling or expression that the coal business is on the rocks and the reasons run the gamut of human deviltry. We have heard that in the not far distant past corn was so cheap that the farmers were compelled to burn it and thus deprive the coal mines of their well earned right to sell coal for this purpose. We have heard that the flood of oil is so vast that it was being burned in preference to coal, and to heap insult on injury that the rail- road locomotives were burning oil in order to pull coal away from the mines. We have heard that the union was responsible for all the woes to which the industry is subjected. We have heard that the family tin lizzie is so depleting the family exchequer that coal could not be purchased and if purchased could not be collected for. We have heard that producing mines are so numerous that the profits are a negligible quantity. These are but a few of the reasons assigned for making the coal producers a class of pessimists which is not good for the industry. All these reasons given and all the others must be taken collectively and these are not the cause but the effect of a rapidly changing civilization. An analogy may be found in the experience of many of us in the electric industry a few years ago. You may remember that less than 20 years ago the high efficiency Tungsten electric globe was introduced. It was so much more efficient than the old carbon lamp that only one-third of the current previously required was needed to produce the same illumination. Consternation seized the ranks of electrical men who had little or no vision, for the out- look was that so little current would be sold that everyone would be bankrupt. This limited vision, however, did not prevail, for all engaged in the industry spurred on by necessity, accomplished many of the things that we are now enjoying the fruits of be- cause the electric industry has grown and is growing by leaps and bounds and every highly efficient improvement is greeted with rejoicing. It is well known that when the old type of carbon arc lamp began to be replaced by modern units the manufacturer of carbon rods thought his doom was sealed and yet these same manufacturers have so adjusted them- selves to conditions that the dry battery business of today is of vastly greater volume and profit than was the carbon rod business of the past. Of course, there are industries that should not have survived anyway that have gone down and out to makeway for vastly improved conditions and can

Jan 1, 1925

By M. H. Gaskell, D. C. Lindley

Small, steeply inclined reservoirs without natural water drives often are found associated with salt domes or other highly faulted structures. Frequently, only one well may be economically justified in these reservoirs, from which oil is produced by an expanding gas-cap drive or by a dissolved-gas drive. Although a large fraction of the oil upstructure from the well may be recovered during primary depletion, only a small fraction of the downdip oil can be produced because of gravity effects. This downdip oil has been defined as cellar oil991 in contradistinction to "attic oil" which is the oil above the structurally highest well in reservoirs where a natural water drive is present. In this study, two methods of producing cellar oil by water flooding a one-well reservoir were investigated by means of a laboratory model. This model was scaled to represent a prototype reservoir having an area of 30 acres, a permeability of 500 md, and a thickness and dip of 30 ft and 30°, respectively. One method considered, the simultaneous injection of water and production of oil from a single well, would require that the lower portion of the productive interval of a well be completed for water injection and the upper portion for oil production. The other method considered, intermittent injection, would involve alternate injection of water into and production of oil from a single well. Injection of water into the formation would repressure the reservoir, causing gas to go back into solution. Since some of the injected water would flow updip from the well, water injection usually would be followed by a waiting period during which the water could drain from above the wellbore. Production of oil by gravity drainage and gas-cap drive could be initiated when water drainage became sufficiently complete. The amount of water produced along with the oil would naturally depend on how soon after water injection ceased that production was started. This process could be repeated in cycles until oil could no longer be produced economically. Of these two methods, the intermittent injection technique would be simpler to put into operation since it does not require a dual completion. Also, it is probably more generally applicable than the simultaneous injection-production method. It is to be expected that in some reservoirs the rock and fluid properties would be such that practical oil-production rates could not be achieved by the simultaneous technique. However, in reservoirs where the simultaneous method will result in practical rates of oil production, it does have the advantage of permitting immediate, continuous oil production; whereas in the intermittent method, oil production is interrupted by periods of water injection and drainage. It was the objective of this study to determine whether these two methods of cellar oil production are practical for the representative prototype investigated and to evaluate their relative merits. DESIGN OF LABORATORY MODEL SCALING REQUIREMENTS The prototype reservoir and fluids were selected to have the dimensions and physical properties shown in Table 1. The laboratory model was then designed in accordance with well known scaling criteria, as discussed by Croes, et al,2 except for one modification. According to Croes, et al, one requirement of scaling a laboratory model to a reservoir prototype is that both the relative permeabilities and dimensionless capillary pressure be the same functions of water saturation for the model and the prototype. Since unconsolidated sand packs are used in the laboratory model to represent the consolidated porous media of the prototype, it is virtually impossible to satisfy this requirement. Much of the difficulty stems from the fact that unconsolidated sands usually exhibit lower residual oil and connate-water saturations than do reservoir rocks. To satisfy the scaling requirement as nearly as possible, Perkins and Collins' have suggested that the relative permeabilities be re-defined as

By V. P. Petrov, V. S. Znamensky

There are a great number of asbestos deposits in the USSR, and some are quite large. The main deposits of chrysotile asbestos are shown in Fig. 1. The Bazhenovo deposit, which is located in the Sverdlovsk region, is the largest and has been mined since 1889. Systematic studies of asbestos deposits were begun from the very be- ginning of Soviet government and are most often connected with the names K.E. Tarasov, P.M. Tatarinov, B.J. Merenkov, N.D. Sobolev, F.V. Syromjatnikov, V.N. Lodochnikov, V.P. Petrov, V.P. Eremeev, L.A. Sokolova, V.R. Artemov, and V.F. Dybkov. Investigations by these people and others helped the USSR be one of the most important producers of asbestos in the world. In this chapter, the main asbestos deposits of the USSR are explained in a general outline from the point of view of their genesis, common features, and differences that must be taken into account for forecasting, exploration, and the mining of asbestos. All chrysotile asbestos deposits of the USSR were formed from magnesium rock as a result of comparatively low grade temperature, hydrothermal alteration, and free crystallization of fibrous chrysotile in open cavities that served as catalysts. Chrysotile, a widely distributed rock-forming mineral, is not in general an important mineral for industry as it is a long fibrous and main vein variety. However, it must serve for geologists as an important prospecting criteria. And, the geologist should search for the mineral not only in places of possible chrysotile generation, but in places where asbestos may be crystallized in its long fibers. The Soviet geologists distinguish chrysotile asbestos deposits in two groups: (1) ultrabasic rocks and (2) sedimentary dolomite terranes, taking into account how the maternal rock was affected by hydrothermal solutions. The largest deposits are related to ultrabasite. In dolomite, the largest deposits are small and their asbestos contains almost no iron, which makes it a better filler for insulating plastics. There are a few types of asbestos deposits within the limits of the ultrabasic group, the largest being a Bazhenovo type to which the deposits of the Urals are attributed. This Bazhenovo asbestos is characterized by the most complete zonality of disposition for various kinds of asbestization. These types of deposits are, for the most part, the only ones presently working in the USSR. The Bazhenovo deposit is connected to the gabbro-peridotite intrusive belt that is about 180 km long and is broken into a number of fault blocks as shown in Fig. 2. Granitoid veins of intruded rocks are found along the deepest faults, and were sources of hydrothermal solutions that affected the maternal rock. The nearest granitoid vein, ultrabasite, is substituted by listwanite that consists of quartz, talc, carbonate, and some other essentially talcous rock. The next zone of hydrothermal alteration is composed of serpentine. The boundry between serpentinite and unaltered ultrabasite is as irregular, diffuse, and rough as the boundaries between all other zones. Nearer the vein of granitic rock, ultrabasite is entirely serpentinized into massif serpentinization that penetrates through cracks and fissures. There is an unaltered ultrabasite space between fissures, and the biggest block is preserved unaltered in the central part of the massif. The Soviet geologists call this ultrabasic sopka. Preservation of the unchanged blocks is of great importance for deposit formation as volume changes are impossible during the process of asbestization and serpentinization. It may be confidently said that asbestization in Bazhenovo type deposits is possible only when alteration of ultrabasite has not completely occurred. Under conditions of massif volume, a very big mass of substance must be carried out of the ultrabasite for the progressive stage of serpentinization. However, in the regressive stage,

Jan 1, 1986

By Paley N, Cameron A, Townson P

Although blasthole deviation is a problem which can seriously affect blasting operations, there is little practical emphasis on controlling this deviation and no practical emphasis on understanding its practical behaviour. The most common way of dealing with it involves tight control over drill set up and surveying hole paths. The surveying might involve simple collar location and inclination measurement to estimate the hole's actual path. At best, some operations routinely survey hole paths after all holes in a stope have been drilled. In addition, although there is an expectation that holes will deviate, there is no planning for this behaviour in order to reduce its impact on the blast. Design decisions are invariably made with the assumption that holes are straight. If and when surveys reveal problems it is possible only to adjust charging and initiation to 'work around them'. In extreme cases the drill might be recalled to fill in gaps. The lack of planning and the lack of understanding are doubtlessly linked.A model is presented that will predict the expected path of a drill hole. By knowing how a selected few holes deviated it is possible to make a good estimate of the deviation of other holes in the same rock mass. After minimal calibration the model can be used to increase the amount of information for a given amount of surveying or the amount of surveying can be reduced while maintaining the same level of knowledge of blasthole deviation. Equally important is the ability to plan for the deviation in future drilling through altering the initial collar angles or drilling from different locations. It is the authors' hope that planning for hole deviation becomes as much a part of the design process as planning for detonator delay scatter and explosive performance variation.

Jan 1, 1992

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By Theodore Marvin

NOW that real progress is being made in building airplanes that can stand up under adverse conditions in isolated parts of the world, utilization of aviation by mining and petroleum companies is proceeding rapidly. This isolation, offering such handicaps to ordinary methods of transportation, also was the thorn in the flesh of aviation until the recent advances in plane and englue design. The accompanying illustration shows one of the six new planes just delivered to the U. S. Government for map making. The planes will be used in Department of Commerce, Coast and Geodetic Survey, Navy Hydrographic, and Insular work. There is a trap door in the bottom of the hull for a Fairchild camera which takes five pictures-vertical, N60°, E60°, S60°, and W60°-at regular intervals. It is manufactured by the Grumman Aircraft Engineering Corp., Farmingdale, N. Y.

Jan 1, 1935

By AIME AIME

INDUSTRIAL Pittsburgh, the center of the coal and iron and steel industry of the world, was host to the Coal Division at its Fall Meeting held there on Oct. 21 and 22 at the William Penn Hotel. The past year has witnessed remarkable progress in new methods of mining and burning of coal and many of the papers on the program discussed these developments. Nearly 100 had registered at the time of the first session on Wednesday morning and this number increased to 168 on Thursday. Owing to the large number of papers on the program, eighteen in all, it was necessary to hold group meetings on Thursday morning, with a capacity attendance at each meeting. . Chairman McAuliffe was on hand early Wednesday morning to open the meeting. George Otis Smith, representing President Lovejoy, came over from Cleveland where he attended the meetings of the Institute of Metals Division. Secretary Parsons arrived later from Cleveland and spent the whole morning with the executive committee of the Division. Doctor Smith, Secretary Parsons, and J. T. Breunich were the official representatives from Institute headquarters.

Jan 1, 1936

By AIME AIME

Maurer's review summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled.

Jan 1, 1967

By J. P. Sheehan, W. R. Hibbard, M. Baeyertz

This paper deals with molybdenum modifications of 5140 steel that have the same hardenability but a better tolerance for phosphorus than the AISI-SAE 5140 grade. Lack of toughness in steels with higher than normal phosphorus contents is well known to metallurgists. This problem is troublesome even within normal phosphorus ranges, if the heat treatment or the design of the part or the service is critical. Under such unfavorable conditions and also in the case of phosphorus contents toward the upper side of the commercial range, the use of molybdenum to replace a part of the chromium in 5140 steel provides a factor of safety. The toughness of steel is variously exhibited in different mechanical tests; broadly the term is applied to the capacity of the steel to deform prior to fracture. Defined in this way, toughness is considered to be an inherent quality that depends upon the composition and structure of the steel, and also upon its temperature during deformation and fracture in the test. In the present state of our knowledge, the type of mechanical test needs to be included in any discussion of toughness, because the revelation of this quality in steel depends on the stress state and rate of stressing imposed by the test. In comparing the toughness of one steel with another by laboratory testing, it has long been customary to use notched tests that impose severe constmint to deformation, and then to test over a range of temperatures to obtain the so-called transition. At temperatures above the transition, the steel fails after considerable deformation and absorption of energy. Below the transition, less energy is absorbed as the steel fails largely by cleavage. The transition range itself is characterized by a more or less abrupt change in energy absorption and type of fracture. The conventional V-notch Charpy impact test has been used exclusively in the work covered by this report. For the steels under study, rather sharp transitions are obtained with this test, at testing temperatures that are easily obtained in the laboratory. The position of the transition on the testing temperature scale provides a rather sensitive index of the toughness of the steel, when the steels under study are similar in character as they are in this work. Turning to the metallurgical reasons for the greater toughness of one steel as compared to another, the authors propose to limit the discussion to the small field under study. Only one structural state is considered, tempered martensite of a hardness of about 28 Rockwell C or 269 Brinell. The study deals first with the loss of toughness in AISI-SAE 5140 steel caused by increasing the phosphorus content from about 0.020 to 0.040 pct. A second part of the work deals with counteracting this loss in toughness by replacing a part of the chromium by molybdenum. A series of molybdenum modifications was studied, in each of which the chromium was reduced sufficiently to duplicate the hardenability of 5140 steel. Phosphorus affects the toughness of steel in two ways. An inherent lack of toughness of phosphorus-bearing ferrite as compared to low phosphorus ferrite has often been noted. Jolivet and Vidall have shown that phosphorus has the same effect in tempered martensite in chromium steels. The other well known effect of phosphorus is to make steel susceptible to temper embrittlement. Temper brittleness is a loss in toughness brought about by tempering steel within a limited temperature interval somewhat below the A1 temperature. In most of the standard AISI-SAE alloy steels, this temperature interval is approximately 850-1100°F. Either of these types of loss in toughness is easily followed by the shift in the transition temperature obtained with the notched-bar impact test. The data to be presented show the beneficial effect of substituting molybdenum for a part of the chromium in 5140 steel with either moderate (0.020 pct) or high (0.040 pct) phosphorus contents. Both the inherent lack of toughness of phosphorus-bearing steel and temper brittleness are counteracted by this use of molybdenum. The work of Jolivet and Vidal mentioned above shows the detrimental effect of phosphorus on the toughness of tempered martensite in the absence of temper embrittlement, as well as the temper brittleness caused by phosphorus. They used two steels, essentially 0.25 pct C-1.4 pct Cr, with 0.044 and 0.013 pct P, respectively. The nonembrittled state was obtained by quenching in oil from 1610°F, then tempering for one hour at 1200°F and quenching in water. In this state the transition temperature range of the low phosphorus steel in the notched-bar impact test was below that of the steel with 0.044 pct P. An additional treatment of 24 hr at 975°F (that is, in the embrittling range) caused both steels to lose toughness, but the high phosphorus steel showed the greater embrittlement. Recently Hollomon2 has published a comprehensive survey and bibliography of the literature on temper brittleness, to which the reader is re-

Jan 1, 1950

By Ernest O. Kartinen

This report is the accumulation of eight years of experience on only one small phase in the business of oil production. It is not intended as a final report but rather as a progress report dealing with the internal corrosion of oil field dehydrating tanks. The corrosion of dehydrating tanks continues to be a problem in the production of crude oil. The deterioration hy corrosion of these tanks falls into three general classifications: (1) Atmospheric corrosion of exterior areas, (2) corrosion of the underside of deck and the rafters and top area of the upper row of staves in that part of the tank which is known as the vapor space, and (3) corrosion of the bottom and shell areas, and the steam coils which are normally immersed in water and thus exposed to the corrosive action of the water. Atmospheric corrosion is primarily a paint problem, and has been omitted in this discussion. The corrosion in the vapor space, in this company's experience, which has been of great concern only in one area. has also been omitted in this discussion. The third, and most troublesome type of corrosion, and the one with which this report deals, is that which occurs in the water-exposed areas of dehydrating tanks, and, to a lesser degree. in some stock tanks. The operating temperature of these waters varies from 80°F to 160°F and the salt counts run from a few thousand to as high as 25.000 parts per million. Corrosion in these tanks occurs in three forms: (1) pits, (2) ringworm type of attack along the vertical and horizontal bolt seams, and (3) as a general attack, spread over a wide area. Steam Coils In dehydrating tanks, our experience has been that the steam coils are the first to show signs of corrosion, and then the shell and bottom areas. This action is not uniform throughout this company's operations. Some installations have coil troubles with very little tank trouble, and some show just the opposite. But in the majority of cases the coils are the more seriously corroded areas. This may be partly due to the fact that we have tried by periodic application to keep a protective coating on the interior areas of the tanks, and some protection has been afforded by these coatings. Through the years several types of hot and cold coatings have been tried with many various methods of cleaning the steel, ranging from use of cleaning solvents to hot and cold Oakite washes, as well as sandblasting. Although experience has shown that a longer life expectancy of a coating is possible after a very thorough steel cleaning job, it has still been necessary to recoat these tanks at least every two or three years. Until a few years ago, vertical spiral steam coil bundles were installed when the tanks were originally erected. When these coils needed replacement, in some cases within 18 months, it was necessary to remove a couple of shell staves to accomplish this task. This required a down time period of several days and was often very inconvenient to the production operations of the leases. This problem was considered on the basis that the coils were expendable, and thus. to eliminate any unnecessary down time when changing coils, the vertical spiral coils were discarded in favor of horizontal flat coils which could be taken in and out of the tanks by way of the cleanout openings, and put together with unions. This made a fairly easily replaceable and repairable coil. But it was still very much of a nuisance when repairs were necessary. Efforts to increase the useful life of the dehydrating tanks led to the adoption of galvanized tanks at an increased initial cost. The zinc coating was depended upon for protection and no other protective coatings were applied. In July, 1944. during the development of a new lease, a 3-ring 1,500 bbl, black iron water tank was converted into a dehydrating tank with steam coils to handle the new production. This tank was coated inside with a cold, brushed-on coating, for protection against corrosion. After approximately 18 months of service, holes developed in the tank and the steam coils. The tank was emptied and cleaned for repairs. The coils were so badly pitted that it was felt advisable to replace them. Coating Becomes Loose Inspection of the tank showed the protective coating to be still in place but loose, and numerous blisters were in evidence. A closer inspection showed that the interior of this tank was so badly pitted under the coating that any further attempt to use the tank was inadvisable. This tank was therefore discarded and a new galvanized tank ordered and set up at considerable expense and inconvenience. In April, 1946, another dehydrating tank installation was made on an adjoining lease. This installation consisted of a 1,500 bbl. 3-ring galvanized tank with two sets of flat steam coils 12 in. and 24 in. up from the bottom. In September, 1947. seventeen months after installation. salt showed up in the boiler feed water. When the dehydrating tank was opened and cleaned, the steam coils were found to be badly pitted — several holes having penetrated through the wall of the pipe. New coils were installed.

Jan 1, 1950

By S. W. Chang, James R. Hein, S-R. Lee, A. Zondervan, H. Choi

"Nine Fe-Mn nodules from the extensive nodule field in the east of Campbell Plateau of southwest Pacific Ocean beneath the Deep Western Boundary Current (DWBC) and Antarctic Circumpolar Current (ACC) were analyzed for the 10Be/9Be dating by AMS (Accelerator Mass Spectroscopy) at IGNS, New Zealand.Several types of nodule morphology were identified including distinctive discoidal forms with overgrowths resulting possibly from overcrowding and partial sediment burial. Five principal nodule facies were also recognized by location and occurrence (Fig. 1) (Wright et al., 2005). Fe-Mn nodules show various concentric internal growth textures, such as, cuspates, large parabolic cuspates, pseudo-columnar, columnar, globular, and laminated, which vary even in a nodule with hydrogenetic, early diagenetic, or mixed origin. Each texture shows micro-textural varieties and different mineralogy and/or chemistry. The genesis of each internal texture was indicated by the REE patterns, the mineralogy of Mnoxides, and the Mn/Fe ratios."

Jan 1, 2017

By AIME AIME

THE fall meeting of the Petroleum Division, held at Tulsa, Okla., on Oct. 11 to 14, devoted two days to technical sessions and two to field excursions. A representative attendance of 250 to 300 engineers and operating officials engaged in oil production marked the sessions and paid close attention throughout to a notable series of highly technical papers. Restricted as the program was to consideration of production problems only, the time proved too short for discussion or even the presentation of the 20 papers submitted. Much informing and pertinent discussion none the less took place, and the sentiment was general to the effect that the meeting was one of the best ever held by the Division. The meetings were held in the auditorium of the Municipal building and local arrangements were well looked after by the Mid-Continent Section of the Institute and the Oil and Gas Association. The combination of the three organizations served to bring together engineers and operators most usefully. F. Julius Fohs, chairman of the Division, presided at the sessions on Monday. Tuesday morning John M. Lovejoy of the local section took over this responsibility in the absence of T. E. Swigart, who was detained in California. The afternoon session was presided over by A. G. Heggam of the Oil and Gas Association and the Tuesday evening banquet by W. C. Franklin of the same organization.

Jan 1, 1926

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 1, 1985

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

By W. A. Walker, G. W. Ostroot

An increase in the number of deep wells being drilled where extreme bottom-hole temperatures are encountered, and the anticipated drilling of wells where temperatures in the range of 500°F or higher may occur, has brought about a comprehensive investigation of cementing materials and of the techniques involved in their proper usage at these elevated temperatures. Included are developments in cements, retarders, weighting materials and other cement additives which make it possible to formulate a variety of compositions to help resolve the cementing problems of these extreme well conditions. The problems associated with the selection and testing of cements are discussed, and a resume of field results is included. Previous studies on strength retrogression indicate that caution should be exercised in the selection of a cementing composition for use in high-temperature wells. It now appears that, by the addition of silica flour as a stabilizing additive to certain cements, compositions covering a wide range of slurry densities can be designed to meet extreme well conditions without strength retrogression. Improvements in cement retarders make it possible to produce a four-hour thickening time at static temperatures up to 500°F. This temperature is considerably higher than conditions presently being encountered in drilling and completion work. Inert weighting materials, used to produce 20-lb/gal or heavier cement slurries, are reviewed. INTRODUCTION As the search for oil continues, the number of wells being drilled to depths of 10,000 ft or below has continued to increase over the past decade. During 1959, there were 50,893 wells drilled in the United States for a total of 209 million ft of hole. Of this total, approximately 4.45 per cent were drilled below 10,000 ft and 0.30 per cent below 15,000 ft, with a record depth of 25,340 ft recorded (Table 1). With the drilling of this record-shattering hole comes the question, "How deep can wells be drilled?".' Limitations with respect to equipment (surface and subsurface), cementing materials and techniques would cause some concern; however, a panel of experts have agreed that the U. S. oil industry has the equipment and know-how to drill a 50,000-ft hole. The greatest deterrent would be the 700°F temperature they would anticipate encountering at this depth. Although the number of wells drilled under what is generally considered hot-hole conditions (230°F and higher) has been relatively high, each well often presents distinctly individual problems and requires separate consideration and selection of special materials, techniques and equipment. At the present time there are over 30 additives and special cements available for use in "tailoring" a cementing composition for a specific well. It is not uncommon to use three or four different additives with the basic cement to produce the desired slurry characteristics. A generally accepted procedure is to make laboratory tests on selected cementing compositions prior to pumping them into wells deeper than 12,000 ft, or where static temperatures are in the range of 260°F or higher. In some instances, it is recommended that laboratory tests be made where less severe well conditions are encountered. Prior to selecting a cementing composition for a particular well, key personnel representing the operator, drilling contractor and service company should meet to determine that each individual is acquainted with every detail which might influence cementing results and to discuss the execution of the job. For cementing hot-holes, a number of factors must be evaluated before proceeding with the operation. Consideration must be given to the following. 1. Thickening time—The slurry must remain fluid for a sufficient length of time to allow displacement down the casing and up the annular space in a primary cementing job or, in squeeze-cementing, adequate thickening time for both the build-up of a satisfactory squeeze pressure and the reversing out of excess cement. The thickening time of standard retarded cements will often be too short under extreme temperature conditions, thus involving special formulations and requiring laboratory tests to determine the proper amount of additional retarder to obtain the desired pumpability.

By J. E. Owen

A model of a porous body is presented in which the pore space consists of a system of voids and interconnecting tubes. Relationships between porosity and resistivity formation factor are determined partly by calculation, partly by experiment. Con triction effects characteristic of the model are shown to be sufficient to account for high formation factors. It is shown that constriction may be combined with moderate amounts of tortuosity to give model pore systems exhibiting to a first approximation porosity and resistivity properties similiar to those of natural porous bodies. INTRODUCTION The relationship between the electric resistivity of a fluid-filled porous body and the geometry of its pore space is so complex that the calculation of the resistivity of a natural porous rock is a practical impossibility. Both the resistivity of a body and its porosity are measurable quantities, however, and previous successes at relating them have been reached by an empirical approach. Efforts at obtaining theoretically derived formulae relating them have generally been unsatisfactory. One of the reasons for this may lie in the pore geometry that has been assumed. THE TORTUOSITY CONCEPT A Parameter called the formation factor is useful in dis-cussing the resistivity of a fluid-filled porous body. This parameter is the ratio of the resistivity of a fluid saturated porous body to the resistivity of the saturating fluid. Formation factors are often available from measurements on cores or from electric logs, and many attempts have been made to correlate formation factors and porosities of geological formations. Whenever a successful correlation is found, the engineer working with electrical logs has a useful tool for the determination of porsities of pay section?. One of the more successful formulae applicable to these correlations is the familiar equation empirically obtained by Archie.' which F is the formation factor. $ is the porosity, and rn is an exponent called the cementation factor. When the for- mula applies, the cementation factor usually is found to be between 1.3 and 2.2. The values for formation factors experimentally obtained are often higher than simple pore geometry would lead one to expect. In an effort to account for such high values certain formulae have been derived based on a so-called "tortuosity concept." In deriving these formulae a synthetic porous body is usually assumed in which the solid material is an electrical non-conductor. and in which the pore system consists of three sets of fluid-filled tubes of uniform diameter connecting opposite faces of the body which, for convenience, is considered to be cubical in shape. The three sets of tubes account for the whole of the effective porosity of the body, and usually, it is specified that they do not interconnect. By considering that the pore tubes are not straight but tortuous, their resistance to the flow of electric currents can be made as high as needed to explain high formation factors. Such an explanation has some basis in fact, but it appears that the tortuosity concept is often incorrectly applied when other factors are largely responsible for observed high resistivities. Recently, Wyllie and Spangler have recognized that tortuosity as calculated by conventional formulae has little if any physical significance.' RESISTIVITY AND THE CONSTRICTION CONCEPT Any explanation of high formation factors which depends solely on tortuosity of uniform pore paths necessarily ignores the effect that variations in the cross-sectional area of the conducting paths have on the resistivity of a body. Although, as previously pointed out, the calculation of such paths for an actual body is impossible, it will he shown that a synthetic pore network can be devised which will yield to analysis, and lead to results in agreement with the experimental data represented by Equation (1). The porous body to be considered is assumed to be homogeneous and isotropic or, for present purposes, identical in its characteristics in the three directions parallel to its coordinate axes. It will he assumed to be built of identical unit cubes, each of which contains a single pore network connecting all faces of the unit cube. A unit of such a pore network is shown

Jan 1, 1952