Search Documents

By Hallan N. Marsh, Bruce H. Robinson

It is now generally recognized that to secure the greatest ultimate recovery of petroleum from a field it is necessary to maintain at all times the lowest possible ratio of gas to oil production. The numerous ways of securing low ratios are not so generally understood or practiced. To many operators, reduction of gas-oil ratio simply means "beaning back" wells, with resultant reduced production rate. This postponement of production is often considered and spoken of as "lost" production, with the result that control of gas-oil ratio is in disfavor with some operators. Various methods are herein discussed by which gas-oil ratio may be reduced, some of which invoLve no curtailment of current production, while others are accompanied by an actual increase of daily production. It is further shown that in cases where rate of production is reduced to conserve gas, the indicated ultimate recovery is generally increased. Principles involved are discussed, and conclusions are illustrated by data from the operation of wells. General Principles The rate and ratio in which oil and gas enter a well are solely dependent, so far as the operation of that well is concerned, upon the pressures maintained in the well opposite the producing strata at various times and at various depths. The method of getting the oil out of the hole, whether by natural flow, gas-lift, or pumping, has no effect upon either rate of production or ultimate recovery except through its effect upon pressures. Oil apparently enters wells according to some such equation as the following: R = KC(Pf - Pw)n Where R = rate of production. K = well coefficient, depending upon thickness of sand, and size and number of pores in the sand. C = fluid coefficient, depending upon viscosity, surface tension, etc.

Jan 1, 1929

By Michael Hoch, Daniel B. Butrymowicz

The isothermal section of the Ta-Ti-Zr-0 system at 1500°C was investigated using X-ray diffraction and rrzetallographic techniques. Up to 71.4 at, pct 0 the system contains nine four -phase regions. Zsopleths at 10, 20, 30, 40, 50, and 60 at. pct 0 were constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of tantalum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct 0 on the Ti-0 and Zr-0 binaries and at 71.4 at. pct 0 on the Ta-0 binary. The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen and Anderk, chmidt, Hayes, Roberson, and asche, and Hoch and athur.' EQUIPMENT The Same equipment as that for the study of the Nb(Cb)-Ti-Zr-0 system was used.' The X-ray dif- fraction patterns were analyzed with the help of the ASTM card set7 and NBS circulars.' MATERIALS The tantalum powder (99 pct pure), the titanium powder (99.6 pct pure), the tantalum pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmont Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., New York. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure", the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE The samples were heated by induction in a vacuum furnace, and examined metallographically and by X-ray diffraction at room temperature. The procedure was the same as that in the Nb(Cb)-Ti-Zr-O work,' EXPERIMENTAL RESULTS AND DISCUSSION OF DATA A four-component system can be represented by a tetrahedron at a single temperature and pressure

Jan 1, 1964

By N. A. Ziegler

THE present publication is a continuation of the work on gas analysis, described in a paper presented before the Institute of Metals Division a year ago.1 While that paper was largely descriptive in character, dealing with the various parts of the apparatus and method of operations, the present one gives numerical data obtained as a result of a series of experiments with iron-carbon alloys. The apparatus and the methods applied are essentially the same as previously described, changes being only in minor details. Attention should be called to the fact that in the present work we are dealing with the gaseous mixtures obtained as a result of vacuum melting of various ferrous alloys. It should be understood that when the terms "degasified sample" and "products of degasification" are used, they refer to the sample remaining after the vacuum fusion of the alloy and the gaseous products removed therefrom, respectively. The writer does not wish to create the impression that the metallic products of this process are absolutely free from any gaseous elements, nor that the gases obtained are present as such in the original sample. These two points are not yet definitely known and are subjects for future investigation. The point, however, which has been established beyond doubt, is that all the gases dealt with come from the metallic charge and are present either in the charge as such, or are produced as a result of chemical reactions going on within the charge. The suggestion that the gases are due to the reactions between the metallic charge and the refractory materials has no valid basis.

Jan 1, 1929

By F. R. Pyne

The following notes are presented in an endeavor to point out the disadvantages attending the use of chrome brick in reverberatory furnaces in which are conducted the treatment of materials of such a nature that absorption by the brick is of too great value to be wasted, and these values must be recovered, if possible, in order to prevent metal losses that can not be tolerated. Several years ago one of the large Eastern copper refineries decided to utilize basic material in place of siliceous material in the walls of their reverberatory furnaces for the treatment of very foul blister copper, as the latter rapidly corroded the siliceous linings. It was also expected that there would be less slag formation, with a consequent decrease in the cost of treatment and a reduction in the metal losses. Magnesite brick were first used, but while the corrosive action of the foul material was greatly reduced, and the amount of slag formed was very much less, the magnesite proved to be unsatisfactory in certain parts of the furnace, because of its tendency to crack and spall badly when subjected to the alternate heating and cooling that takes place in a reverberatory refining furnace. This made many repairs necessary, and consequent frequent interruption in the operation of the furnace, which, together with the high price of the magnesite brick, ran up the cost of maintenance to an unreasonable amount. It was, therefore, decided to substitute chrome brick for magnesite brick in the parts of the furnace affected. The results, as far as the reverberatory furnace was concerned, were very satisfactory. The corrosion due to the action of the foul blister was small and the amount of slag formed was no greater than when using magnesite, and the tendency to crack and spall shown by the magnesite was eliminated. Gradually the use of chrome brick was extended to all furnaces, those treating blister copper as well as those melting cathodes, and the results were so satisfactory that the siliceous roofs were replaced by roofs of chrome brick except in certain places where experience showed a more satisfactory performance on the part of the silica brick. It was immediately recognized, for both the magnesite and the chrome brick, that the metal absorption was very heavy, but it was felt that the

Jan 1, 1918

By T. L. Joseph

IN connection with its investigations of the blast'-furnace process, the Bureau of Mines, in coöperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferromanganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new, raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the coöperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests.

Jan 1, 1928

By W. E. C. Coxe

MANY of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission was accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned ; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which be furnished for the head of the rail could not be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

By O. Tiitu

Drying is a unit process that has numerous applications in metallurgical process industry. Kumera Technology Center is a worldwide equipment and process supplier, who has expertise on both direct and indirect drying. In a conventional direct heated dryer, the required energy is obtained from combustion of fossil fuels emitting a considerable amount of off-gases. However, thermal energy can be already available in some metallurgical plants such as modem copper smelters where steam is produced by waste heat boilers of flash smelting furnaces. The total volume of off-gases, and especially the amount of harmful gases, released into atmosphere can be remarkably reduced when using steam as an indirect energy source for drying. Kumera Technology Center has developed a new type of steam dryer for drying of, for example, abrasive copper concentrate with silica sand. In the development of the new dryer, Kumera's approach has been to combine the best properties of both the existing steam dryers and the rotating drum dryers. In the design, special attention has been paid to overcoming the reported problems of excessive wear and clogging of steam tubes and to reducing the required maintenance operations. The Kumera Steam Dryer, having a patented flexible steam tube arrangement inside the rotating shell, has a high effective heating area - drum volume ratio without leading to problems with build-up and clogging. It can also be easily scaled up so that a single dryer can dry all of the feed for a large flash furnace. In this paper, we will present the operational and maintenance experiences from two years operation of the first full-scale Kumera Steam Dryer at Norddeutsche Affinerie Aktiengesellschaft in Hamburg, Germany. We will also provide an overview of the future developments with respect to construction and scale up as a response to market demands.

Jan 1, 2002

THE Mining Methods Committee during the past year has spent much of its time developing the interest of members of the Institute in the work that comes under its direction. The response on the part of the membership has been most encouraging and in order to give a concrete form to the program which it hopes to develop, an "Outline for Papers on Mining Methods" has been drawn up and is herewith submitted for consideration. This outline has slowly taken shape until it now represents ideas contributed by a great many men, and it is hoped that it will be suggestive and helpful in the preparation of papers. This program can be used for the preparation of papers covering single large operations or, preferably, as the basis for a description of methods and the presentation of results obtained either in different districts or in different branches of the industry. The Committee presents this outline for the consideration of the various Sections of the Institute with the request that they will endeavor to interest the members of the Sections in covering comprehensively the mining operations with which they are connected. It is not the plan of the Committee to publish a paper on every mine, giving all the details outlined, but rather that an engineer familiar with a district prepare the general information and engineers of each important mine in the district compile the specific information of the mine with which they are connected. The general information and the specific information shall be sent to the Committee, and with this information the Committee will prepare a paper on the results obtained under the various mining methods in the different districts. The Committee requests that all papers shall be compiled under the direction of the Chief Engineer of the company and then submitted to the General Manager before acceptance for publication or compilation and tabulation with other similar data. Where the study of this subject approaches the fields of other standing committees of the Institute, the

Jan 5, 1922

By Faruk Oksuz, Clay Haynes, David Egger

The United States Army Corps of Engineers (USACE) has committed to solve a major drainage problem in the suburban Chicago community of Griffith, Indiana. The Cady Marsh Ditch is currently undersized and on occasion spills its banks causing flooding and economic setbacks to the community. Preliminary studies have identified both tunnel and surface solutions as being attractive and viable. The USACE has decided that this project is an opportunity to use the design-build contracting approach to maximize ingenuity in project approach and to allow the market to dictate whether a surface or subsurface solution is most attractive. The tunnel would be over one-mile in length through sands, gravels and clay. Water control will be an issue during tunneling. The paper will explore the contracting approach to the project and the adaptation of Underground Technology Research Council (UTRC) guidelines for underground contracting to a design build project. The roles of Owner, Owner’s consultant, and design-build contractor will be defined as interpreted by the USACE and key contract provisions will be described and contrasted with a traditional design-bid-build approach to tunnel construction.

Jan 1, 2003

By W. R. Finney

THE formation of scale in boilers and other industrial equipment, and the corrosion of such equipment, are closely related problems. Since in the petroleum industry these problems cover a very broad field, this paper has been confined to the effects of scale and corrosion on gas engines, compressors, pipes and fittings, used in plants extracting gasoline from natural gas, and the steps taken in arriving at a workable plan for combating these evils at the Midwest Refining Co.'s plants in the Salt Creek field, Wyoming. Eliminating, or at least minimizing, the many deleterious effects occasioned by the use of bad water in jackets and cooling systems of gas engines and compressors has been the subject of much study for many years but no generally accepted plan has been evolved. The problem was unusually difficult at Salt Creek, as the severe winters of Wyoming bring operating conditions quite different from those encountered in warmer states, and the water available was especially bad. While the conditioning of water to prevent scale and to lessen corrosion may not be a particularly difficult problem in plants in large industrial centers, it becomes much more difficult when attempted at plants remote from railroads and by men without previous experience to guide them. In fact this difficulty has been so great in the Wyoming oil fields that until comparatively recently it has been the practice to allow much equipment to be ruined rather than to attempt corrective measures. At the Midwest plants this problem was given attention first by the plant men and later by both plant men and laboratory staff. To the latter it was simply one of many problems which arise in connection with field and plant operations, which must be studied and, if possible, solved. Many mistakes were made during the course of this investigation, but since mistakes, properly interpreted, are of value in guiding one's steps aright, it is believed that a review of the different stages of development which have led up to the present method of handling this problem will prove of interest to the industry.

Jan 12, 1926

JUDGING from the attitude of past and present Parliaments in Australia, it is a' reasonable assumption that encouragement of the principal industries has been adopted as a main principle in the government of the country, but while in most cases bonuses, subsidies, and other means have been proved successful and become recognized as established methods in the case of mining, which is undoubtedly one of the most important industries, the question is complicated by difference of conditions and variable quantities, and it can scarcely be said that any system has been proved generally successful. Indeed, it would not be a very extravagant statement to assert that problems connected with affording direct monetary assistance in aid of mining development, and at the same time devising a system adaptable to the varying conditions to be met, are, in every State of the Oommonwealth, matters continually exercising the minds of those concerned in providing and ailocating such assistance ie Parliament on the one hand, and the Department of Mines on the other.True, there are methods in vogue of granting State assistance to the mining industry which have undoubtedly been successful, but it is in most cases questionable whether the beneficial results following successful expenditure in one direction have compensated.

Jan 1, 1911

By Ernest Stütz

(New York Meeting, October, 1918.) THE problem of increasing blast: furnace efficiency through diminution of flue-dust production while operating with burdens consisting largely of fine ores has of recent years attracted the attention of metallurgists, whether directly or indirectly interested in the economies of iron smelting, and the various methods evolved from theory or practice have been submitted to wide discussion. After the very thorough and, at that time, exhaustive view of the whole subject, which was afforded to the industry by the meeting of this Institute in February, 1912, the subject was again taken up at the meeting of the Verein deutscher Eisenhüttenleute at Diisseldorf in December, 1912. While American and German conditions are not entirely identical, it may be of interest to give here the words of the gentleman summing up the discussion at the Diisseldorf meeting: ' The chief advantage offered by the use of briquettes lies in the fact that disturbances in the furnace, caused mostly by the presence of fine ores in the burden, are avoided, and that blast pressure can be considerably reduced. The resulting economies cannot be overrated, as, with lower blast consumption per ton of product, the installation will be able to take care of increased production. In consequence of lower pressure and speed of blast, heat is more efficiently utilized, flue gas temperature is lowered, and coke particles are less liable to be carried along with the flue dust, of which considerably less is produced. Finally, by increased regularity of operation and higher . temperature in the lower parts of the furnace, the quality of the product is improved. The question of briquetting iron ores has grown to be one of the most important in the iron industry, and, it is not any more a question of what is the cost of briquetting ton of ore, but what, in using ore briquettes, is the cost of production of a ton of iron.'

Jan 7, 1913

As near-surface underground mines progress deeper, the inevitable question is whether to convert from truck haulage to shaft hoisting. The desire to defer capital expenditure frequently delays investigation of the shaft option, or deferral of a decision to start shaft sinking, unless the shaft option is clearly significantly better than trucking. By the time increasing depth makes trucking uneconomic, there may then be insufficient resource remaining to justify a shaft, and the mine must close. However, had the shaft been built earlier, its lower operating costs would have permitted the mine to continue to greater depths. This paper presents a methodology for investigating the shaft versus trucks decision. As well as the typical analysis of which option is preferable at the time the analysis is conducted, the process presented illustrates how the timing of the decision to sink a shaft is critical. The paper shows how to identify the latest date at which the decision to sink a shaft can be made, after which time the shaft option will not be economic. It also illustrates how to assess the resource that may be required to justify the shaft. Considering this in conjunction with the latest decision date, implications for the companyÆs exploration program are discussed.

Jan 1, 2005

By S. W. Parr, A. R. Powell

FOUR general methods have been used in the study of the decomposition of coal. The first has been directed toward the processes of coal formation, the second has been by means of microscopic studies, the third from the data of destructive distillation, and the fourth has made use of various solvents. Applying these methods to the sulfur of coal, it has been found that the organic sulfur of plant and animal life enters into the formation of coal and remains in organic combination in the final product. The inorganic sulfur is almost entirely combined as iron pyrites and marcasite. The infiltration of hydrogen-sulfide waters is doubtless a large factor in these combinations. Sulfates are found in very small quantities except where free oxygen has entered the coal strata. The mechanical mixing of detritus with the early coal material is another source of sulfur. In this case the sulfur is distributed in microscopic particles throughout the mass. In destructive distillation, a part of the sulfur comes off as hydrogen sulfide and various thiophen compounds, but this furnishes little information as to the nature of the sulfur compounds in the coal itself. The use of solvents has given valuable data concerning the sulfur compounds in coal. Fremyl and later E. Guignet2 noted the action of alkaline solutions on coal after treatment with nitric acid and Anderson and Roberts3 showed the presence of large quantities of organic sulfur in the extract so obtained. In a study of the phenol extract of coal, Parr and Hadley4 found organic sulfur in the soluble organic material. These investigations proved the presence of organic sulfur in coal in addition to the inorganic forms, such as iron pyrites and sulfates. T. M. Drown6 attempted the analysis of the pyritic and sulfate sulfur as distinct from the organic forms by means of sodium hypobromite; no definite proof of

Jan 1, 1920

The Hartley layered mafic igneous complex within the Great Dyke of Zimbabwe contains economically-recoverable quantities of platinum group metals and gold, nickel, copper and cobalt. The recoverable metals are concentrated in a thin gently-dipping stratigraphic unit - the Main Sulphide Zone. The Hartley Platinum mine, jointly owned by BHP and Delta Gold NL, is scheduled to come on stream at the end of 1996 at an initial mining rate of 2.16 million tonnes per annum and will produce approximately 150 000 oz of platinum and 3300 tonnes per annum of nickel, as well as saleable amounts of palladium (110 000 oz), rhodium (11 500 oz) and copper (2232 tonnes).

Jan 1, 1996

By J. M. Glass, C. D. Sholtess

We at Hughes Tool Co. are extremely proud of the quality of the hardware and techniques introduced through our efforts in tunnel-machine development and of the ready acceptance of them by manufacturers and contractors throughout the world. All of us who attended the conference and who are represented in the book, we believe, anticipate an increasing need for improved methods of underground excavation. The development of such methods will permit the further exploitation of our underground resources plus providing underground space for transportation and habitation at a rate compatible with demand. We hope that our comments, derived from the application of Hughes Tool Co.'s rotary boring experience, may provide a better understanding of the boring method as a possible avenue through which the desired improvement in underground excavation may be attained. We hope you may also become aware of some of the problems Hughes, as a pioneer developer of raise, shaft, and tunnel-boring equipment, must face prior to further major undertakings in this very interesting field. Our task is to acquaint you with the present status of the Hughes Tool Co. development program as it relates specifically to tunnel-boring machines. We feel this task can best be accomplished by a brief review of the general sequence of events leading to and constituting an equipment development program and more specifically the manner in which these events have occurred to either influence or further our boring-machine development program. The development of a machine to accomplish a certain function or series of functions is usually a very long and tedious process to which any number of individuals must contribute, perhaps over a period of centuries. Of particular irony is the fact that often those who contribute most generously do not necessarily reap the greatest immediate benefit. A marketable ma- chine will, however, result from a sequence of events such as these: 1) A problem or need is defined. 2) An idea is born to eliminate the problem.

Jan 1, 1970

By C. P. Watson

Economics has been defined as the useful application of wealth or material resources. The search of alchemists in the Middle Ages for s formula by which base metals might be transmuted into gold was no more intensive than has been the search by all branches of the oil industry for methods whereby the rnatcrial resources of West Texas in the nature of sulfur-bearing oil might be usefully applied. The purpose of this paper is to present in brief space developments that are conceded to possess economic significance. History The first discovery of oil in commercial quantities in the Permian Basin of West Texas was the Westbrook field in Mitchell County in 1920. Three years later the discovery well in the Big Lake field was cornpleted as a small pumper (70 bbl.) at a depth of 3028 ft. In 1925, discovery of the Powell or World pool in Crockett County stimulated activities in the Permian Basin, further establishing the importance of the Permian limestones as sources of production. The years 1925 and 1926 were marked by a period of extensive leasing and drilling activities. At the close of 1926 more than 7,000,000 acres had been leased and discovery wells completed in the Hurdle, Hendricksand Yates fields, definitely establishing the importance of the Permian Basin as a source of production from free-flowing wells. Review of Fields The producing fields in the Permian Basin are grouped on three distinct lines of folding. These may be separately identified as the Big Lake-Powell fold; the Yates, Hurdle, and Church-McElroy area and the Winkler County development. Production is derived from a porous limestone stratigraphically uniform, encountered at depths varying from 900 to 3100 ft. Lenticular sand bodies above the lime in Howard County have resulted in the

Jan 1, 1928

By Arthur L. Flagg

The Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of moderate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 Sq. miles, bounded on the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sea-level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet without railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a sligh degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction. At present all supplies and equipment are hauled in by wagon from Stites, a distance of 58 miles, over a wagon road constructed by the State in 1904, following in the main the old Nez Perce trail. While this is not a bad road, it is not all that might be desired. Starting at Stites at an elevation of 1,327 feet above sea-level, the road runs through low hills to Clearwater, a distance of 10 miles. In the next 16 miles the climb is steady until the Mountain House is reached, which is near the summit of Mount Pisgah. This is the highest point passed on the road, having an elevation of 6,500 ft. From the

Jan 1, 1914

By Harold L. Bare, Frank R. Barnako

Coal mining historically has been a. hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work. COAL MINE ACCIDENT EXPERIENCE The US Mine Safety and Health Administration (MSHA) is the main source for accident experience data in coal mines. Coal mine operators are required, by law, to forward to MSHA monthly the number of fatal and disabling injuries, man-hours worked, and tons of coal mined. This information is compiled and published quarterly, with annual summaries, by MSHA. Trends in the number of fatalities and fatal injury rates are shown in Fig. 1. Major coal mine disasters, with number of miners killed, and dates of coal mine safety legislation are shown in Table 1. The fatal and disabling injury frequency rates for the coal industry are shown in Fig. 2.

Jan 1, 1981

Jan 1, 1964