Search Documents

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By I. N. Knapp

Introduction.-The special object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such description as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft. in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, boilers, and pipe yard were also carried on 3-in. planking. Drilling Outfit.-This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35 h.p., "oil country" boilers, one double 8 ¼ by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary' jetting swivels, hose, complement of tools, pipes and connections, and. a mud mixer, with engine.

Jan 12, 1914

By David B. Reger

Widespread wildcatting for new supplies of natural gas and the beginning of importation from the southwest characterized the petroleum industry of West Virginia during 1944. Within the state, drilling for oil did not increase but. more gas wells were completed than in any previous year since 1937. Out of 40 wildcats drilled there were 25 gas discoveries and 15 dry holes. No commercial oil was found in the 40 wells. The proved limits of several oil pools were slightly extended by marginal drilling, resulting in 1300 acres of new oil territory, although no distinctly new pools were found. At least four new gas pools were assuredly discovered and various successful wildcats indicate future pools or wide extensions. The new proved gas territory, in definite new pools and definite extensions, is about 34,000 acres. A considerable net decline of proved oil has occarred and probably a slight decline of proved gas reserves. The account of operations, as gathered from trade journals and other reporting services, shows that 918 new wells were drilled, resulting in 71 oil wells with 613 bbl. of daily new production; 577 gas wells with 305,372,000 cu. ft. of daily open flow, and 142 dry holes. Also, 107 old wells were drilled to deeper sands, with 22 bbl. and 12,327,000 cu. ft. of added production. On the new wells the oil average was 8.6 bbl. per well per day, and the gas average was 529,241 CU. ft. per well per day. On new wells the ratio of dry holes to completions was 15.47 per cent. On deeper drilling the ratio of failures was 19.63 per cent. Production of oil for the year was estimated by the Oil Weekly as 3,069,000 bbl., as compared with 3,349,000 bbl. in 1943. Production of natural gas for the year is estimated by the author as 200,000, 000,000 cu. ft., as compared with the U. S. Bureau of Mines final figures of 223,789,000,000 cu. ft.t in 1943.

Jan 1, 1945

By F. G. Tickell, R. C. McCurdy, O. E. Mechem

The behavior of fluids in the voids of a rock is fundamental to the study of many of the problems of oil-field development and production. For it is by virtue of these openings between grains that oil and gas are able to move through the rock, to be contained by the rock, and to pass from the rock into the well. The capacity to contain fluids is measured by the porosity of the rock, and the ease of fluid movement is governed by the permeability. When the engineer wishes to estimate the amounts of oil and gas in an underground reservoir he is often concerned with the porosities of the rocks and, when dealing with problems relating to rate of production, he is more likely to be interested in the permeabilities of the rocks. Rocks are permeable because they are porous, but they may be porous without being permeable. Clays are very porous, and yet they are impermeable from a practical standpoint. Attempts have been made1 to correlate permeability with porosity for certain rock members but, where a definite relationship between these two properties is found to hold, it is purely fortuitous and local. Porosity and permeability do not necessarily bear any quantitative relationship to one another. The porosity of a substance is the percentage of void volume to bulk volume. The petroleum engineer is usually interested only in the inter-granular voids that are accessible to fluids. In measuring porosity he does not wish to include scaled openings. The measurement he desires is one of "available porosity," otherwise called "apparent porosity." The porosity of a natural aggregate of solid grains, such as a sandstone or clay, is governed by: (1) Grain-size distribution, (2) angularity of grain, (3) colloidal content, (4) degree of compaction. It is not difficult, for unconsolidated rocks, to measure the effect of any one of these when it alone is varied, and then to predict what the effects on porosity will be for such single variables. It is very difficult, however, if not

Jan 1, 1933

By J. W. Littleford

The Roan Antelope Copper Mines Ltd. are situated in the north central part of Northern Rhodesia, at an altitude of 4000 ft. and 13" south of the Equator. The town site (Luanshya) is well situated and enjoys among other things a really temperate climate for 10 months of the year. The two spring and summer months, October and November, while hot and humid, do not bring any great discomforts as compared with many other mining camps. Strictly modern brick homes, with electric lights, purified water, telephone and water-borne sewage, add to the comfort of the employees. A rainfall of approximately 60 in. per year furnishes ample water for both industrial and domestic purposes. The rainy season generally begins in October and lasts through until March. As much as 3 to 4 in. is recorded in 24 hr., but this offers no difficulties because the runoff is very rapid. The property is connected by a 24-mile branch line from Ndola with the main line of the Beira-Mashonaland and Rhodesia Railways Ltd. Practically all supplies from overseas are transported over this line from Beira, 1743 miles distant on the east coast in Portuguese East Africa. The mine output also leaves Africa from this port. Passenger service is principally via Cape Town or Durban, a distance of about 2100 miles to either port. The Imperial Airways maintain a service from Cape Town to Croydon, taking 9 days for the trip. Connections can be made with this service at Broken Hill, 150 miles south of Luanshya, by either rail or automobile. Thus, after several days of travel through virgin bush, a visitor arrives at a typically modern town site in the heart of Africa. Every development in mining, milling and smelting practice is used to advantage. Plan of Mill The practice in the three principal phases of the production of copper from the ores of this company have been published from time to time. Milling practice, however, is continually changing and what may be

Jan 1, 1935

By Robertson A. D C, Cranfield L. C, Murray C. G

Most base and precious metal mineralisation in the Gympie Province is genetically linked to intrusion of branitoids of Late Permian to Late Triassic age. Most lodes are hydrothermal quartz and quartz-calcite veins at intrusive contacts, within either the granitoids themselves or the country rocks, and commonly associated with dykes. Other types of intrusive related deposits are disseminated porphyry type Cu, base metals in skarns, and Mo in quartz pipes and veins. Although the Late Permian-Late Triassic granitic intrusives can be subdivided in terms of age, it is not yet possible to relate deposits of particular metals or styles to granites of a specific age on a regional scale.Some significant mineralisation is not associated with granitic intrusions. This includes the Gympie goldfield, by far the largest known deposit within the Gympie Province. Gold occurs in quartz veins crosscutting Early Permian volcaniclastic sediments and also in NW striking fault zones. The source of the mineralisation is unknown. Gold and silver also occur in epithermal, disseminated and breccia hosted deposits within Late Triassic continental volcanics. Epithermal Hg mineralisation at Kilkivan may be related to Early-Middle Triassic volcanics.

Jan 1, 1990

By George Sachs, J. Spretnak

The process of recrystallization has not as yet been explained satisfactorily. Some definite conclusions could be drawn from recent investigations, such as, for example, that recrystallization is a process of nucleus formation and crystal growth1 and that the orientations of the nuclei correspond to some fragments of the original crystals, which have been considerably distorted during deformation.2 There are, however, a number of metals and alloys crystallizing in the face-centered cubic system, which form a particularly simple orientation if recrystallized as a sheet.3 Such a shect is almost a single crystal with the cubic axes parallel to the rolling, transverse, and normal directions of the sheet. This preferred cubic or (100) orientation of the recrystallized sheet has been considered to be very different from the rolling structure of the same metals,4 but there are two reasons why this last supposition remains open to controversial discussion. The first reason is academic: In practically all cases except the one mentioned above, close correlations and similarities between rolling and annealing orientations have been observed; for instance, in iron and steel sheet.6 Secondly, no deformed metal actually forms a simple orientation. In any thoroughly investigated case a number of different orientations and considerable scattering or deviations from the ideal orientations have been found.6 It is generally true that investigations on single crystals have shown that a definite orientation is approached in stretching or in compression of an originally undisturbed crystal.7 In the special cases, however, where the initial orientation was close to an important crystallographic direction that differed from the final "ideal" orientation, the resulting orientation changed very little by deformation, staying somewhere in the vicinity of the initial orientation.8 Such deviations

Jan 1, 1940

By Sivell W

We discuss the origin of the Patuki ophiolite complex and the Dun Mountain ultramafics of Middle Permian age in Nelson, New Zealand. It is shown that the Patuki volcanics have strong affinities with tholeiites of mid ocean spreading ridges transitional to alkaline basalts similar to those from fracture zones and ocean islands. At D'Urville Island, typically pillowed alkaline basalts enriched in rare light rare earth elements (LREE) - ophitic spilites - are associated with LREE-depleted (N-MORB-like) tholeiitic spilites with intergranular textures. The metabasalts are associated with a wide variety of sediments, and with sediments are intruded by conformable sheets of serpentinite. Coarsely crystalline mafic and plagiogranitic rocks signify vents and magma chambers, and we propose that the group developed as ocean crust from a slowly spreading mid-ocean ridge, transform association, overwhelmed at intervals by volcaniclastic sediment. Detailed mapping at a scale of 1:5000, and stratigraphic and geochemical development and structural coherence, show that the group is not melange in the Franciscan sense. The Dun Mountain Group, of serpentinites, peridotites, dunites, gabbros and other rocks, intruded the upper Patuki Group as a linear series of aligned pods and sheets. They carried up with them tectonic inclusions of older rock, which were metasomatised, and altered wall-rock, and one low angle dike passed several hundred metres into overl~ing sediment, at moderate temperatures (500 C). The rocks did not act as a floor (and alleged source) for the Patuki, but partly post-dated and were emplaced into Patuki.

Jan 1, 1987

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

This Information Circular from the National Institute for Occupational Safety and Health (NIOSH) documents and supplements the information presented in a series of workshops held during 2002 and 2003. The primary intended audience consists of all who are involved in developing and conducting miners? training. According to the Mine Safety and Health Administration (MSHA), mine operators reported 240,000 full-time equivalent workers and independent contractors reported 42,000 full-time equivalent workers working on mine property during the year 2000. Unfortunately, these workers have a relatively high risk of suffering serious work-related injuries and illnesses. The mining industry has the highest rate of occupational fatalities among all U.S. industries. The fatality rate is 30 deaths per 100,000 workers compared to 4.6 for all private industry(Morbidity and Mortality Week Report, 2001; NIOSH, 2002).Compared to workers in other industries, miners also have a relatively high rate of nonfatal lost-time injuries, and their injuries tend to be more severe (Bureau of Labor Statistics, 1999). Many miners are also exposed to significant health hazards, including coal and silica dust, diesel exhaust, and noise. More than 1000 U.S. miners die of lung disease each year(NIOSH, 1999).

Jan 1, 2002

By M. E. Nicholson

The solid solubility of boron in iron has been determined by saturating iron with respect to FeyB at several temperatures from 870° to 1135 C. In alpha iron the maximum solubility was found to be 0.002 pct B and in gamma iron the solubility varied from 0.001 pct at 915°C to 0.020 pct B at 1165OC. The eutectic and peritectoid temperatures were found to be 1165° and 911 °C respectively and the gamma iron solidus was located approximately at 0.020 pct B. RECENT investigations of boron-treated steels', ' indicate that the solubility of boron in austenite is of the order of 0.003 pct at 900°C. This has led to the general belief that the solubility of boron in a and r iron is considerably less than that indicated by Wever and Muller." Therefore the solid solubilities of boron in a and r iron have been re-determined. The eutectic and peritectoid temperatures were also remeasured and the r-iron solidus was studied in some detail.* In 1929 Wever and Miiller investigated the phase equilibria of Fe-B alloys. Fig. 1 shows the solid solubility region of the Fe-B diagram based on their investigation. They found that boron lowered the A, transformation temperature to 1381 °C where saturated 6 solid solution "which must contain about 0.15 pct B" and "r solid solution containing about 0.10 pct B" are in equilibrium with liquid containing 1.9 pct B. At the eutectic temperature of 1174"C, 7 solid solution was found to contain "about 0.15 pct B." A peritectoid relation was found to exist between a and y iron with an invariant temperature at 915 "C, where the boron solubility in 7 iron was "about 0.10 pct B" and the solid solubility in a iron "did not exceed 0.15 pct B." Although most of their

Jan 1, 1955

By August J. Breitenstein, W. Spencer Hutchinson

The outstanding engineering accomplishment of the last three decades has been the development and application of more and cheaper power and its use instead of the labor of men and animals. Substitution of power for manual labor has taken effect on every hand in the United States. With the aid of energy mechanically available to his hand, one man does the work that only a few years ago required two, three or even a greater number of laborers. The results in respect to the favorable economic effects are well known; namely, increased production, higher wages and lower costs. On the other hand, the vast social effects, both good and bad, have been none the less important, even if less understood and only casually regarded. The chief sources of energy today are the mineral fuels, coal and petroleum. In the United States they yield more than 90 per cent of the total energy demand. Thirty years ago the proportion of energy supplied by the mineral fuels was likewise above 90 per cent, but the division according to origin was very different. These relations are shown for the years 1900, 1930 and 1950 in Table 1. Method or Preparation and Interpretation of Statistical Data The fuels comprised in this study are: (1) the coal group including both bituminous and anthracite coal; (2) the petroleum group, taking in not only petroleum but natural gas and natural-gas gasoline. Natural gas for many years has been used in localities relatively near the wells but statistics were found no earlier than 1910. Demand has rapidly

Jan 1, 1934

By Alexander Anderson

In many oil fields a great variation in the production of adjoining wells has long been observed, and a certain proportion of dry holes, situated between prolific producers, has been regarded as normal without thorough investigation as to cause. Similarly, an occasional prolific producer has been found in a part of a field where all other holes have proven disappointing. Adjoining wells which showed an unreasonable difference in production have been surveyed, and the bottom of the poorest producer has been found to have lost sufficient vertical depth, through its drift, to diminish seriously its penetration in the oil zone. Again, the bottom of the good producer has been found to he more favorably situated by its migration up structure. Surveying of wells in California fields has shown many instances where the dry hole has drifted far off the structure to such a degree that no amount of deepening could ever convert it into an oil well. In other cases, edge wells have been found to drift into the field. At this time, in California, the surveying of oil wells is beginning to he accepted as a routine part of operating procedure. Some operators are surveying all of their new wells and, in some of the recently discovered fields, this practice is providing invaluable assistance in methodical development. The information that has been obtained from the surveying of many wells has convinced most operators that it pays to give careful attention to the drilling of wells. Chews are now usually cautioned to avoid reckless competition with each other. Whereas, formerly, certain companies demanded a large footage from their drillers, they now issue orders that a very moderate speed in drilling shall he maintained and that every care be taken to avoid practices likely to cause excessive deviation of the hole frorn vertical. As a result of these new instructions to drilling crews, a distinct decline in the average drift of the wells drilled by these operators has taken place and fewer dry holes are being drilled from good locations. To the petroleum engineer and the geologist, oil-well surveys provide the necessary data required for the construction of the correct cross-

Jan 1, 1929

By H. T. Mercer, A. C. Paulson

The composition of steel and the theory of its heat treatment have been so ably discussed elsewhere that it is unnecessary to go into the subject here. The purpose of this paper is to describe briefly the method of treating drill steel at the Copper Range mines, giving some of the troubles encountered and the manner in which they were overcome or corrected. To study the matter properly, it was necessary to devise a system of records that would show the actual underground performance of the drills. To illustrate this system, the records of the Champion mine are used, as it is at this mine that most of the work along these lines has been done. Reports from each drill machine are made daily by the shop and mine, and tables compiled from these reports show the footage drilled, steel broken, drills received and sent out at the shop, drills sharpened, and bits cut off. These data show what each machine or party is doing and whether the miners' supply of drills is kept up to date. There have been times when the supply of drills has been short and time lost by the miner in looking for drills. The daily records show the number and condition of drills on hand at all times. Under the old method of sharpening, the drills were heated in a coke furnace, the proper degree of heat being judged by color. Then they were sharpened in a machine, reheated in a second coke furnace where the proper heat was again determined by color, and quenched in water. While this method was fairly successful in the hands of a careful workman and for the solid steel used in the old piston drill machine, the introduction of the faster water machine, using hollow steel, produced changes both underground and in the shop. Much more was expected of the hollow-steel and hammer-type machine, with its improved method of rotation, but troubles due to breakage, burnt bits, uneven tempering, etc., at once appeared.

Jan 1, 1922

Bougainville Copper Limited (BCL) operates a 50 Mtpy copper/gold/silver mine and concentrator on Bougainville Island, Papua New Guinea. BCL has installed an in-house developed data logging and supervisory process control system using a DEC PDP 11/73 mini-computer in the mill and has recently installed a similar system in the crushing plant. Together with the central DEC VAX 11/780 computer, they form part of a high speed, fibre optic, local area network in the concentrator. The in-house developed software, known as BIAS (Bougainville Copper Information and Automation System), was developed as a low cost option to interface to a number of different existing plant input/output systems while providing the capability to make maximum use of computer networking facilities. The package includes the more usual control system colour displays and data logging features, but also makes provision for two novel features: (a) Any user connected to the computer network can access the system displays. This allows metallurgists and management to monitor (but not control) plant operation from their offices. (b) Specialized application programs for performing advisory and supervisory control, dynamic simulation, and data analysis are easily incorporated into the system. The mill process system currently runs rougher/scavenger flotation stabilizing control and general data logging. The crushing plant system currently performs data logging only; however it will soon be augmented with the facility to run dynamic crushing plant simulations. Future developments will concentrate on making greater use of the detailed information available from the mine's fully automatic truck dispatch system which runs on a VAX 11/780 computer. Milling process control will be expanded to examine possible economic control of the operation of regrind and cleaner flotation circuits. An advisory water management system to optimize water supply within powerhouse generating capacity constraint will also be investigated.

Jan 1, 1987

By E. H. Denny

IN the past few years many men, including technically trained engineers, have been asphyxiated in metal mines, coal mines, tunnels and surface wells where a few relatively simple precautions with regard to ventilation and air testing would have saved them. Death from mine gases is analogous in some respects to death from poison and from drowning. The respiratory passages of a victim who has breathed oxides of nitrogen from burning explosives are badly irritated and a few hours or even a day after exposure he may develop a quick and fatal pneumonia; if, however, he enters without respiratory protective apparatus an atmosphere deficient in oxygen (a condition that may occur in unventilated or poorly ventilated parts of all underground mines) he collapses and if not rescued dies more quickly and surely than a lone nonswimmer who falls suddenly into deep water. An example of an atmosphere virtually without oxygen was demonstrated by an air sample taken by a Bureau of Mines engineer wearing oxygen breathing apparatus in a Cripple Creek shaft some years ago, during the recovery of the bodies of two victims of asphyxiation; analysis of the sample by the Pittsburgh laboratory of the Bureau showed the presence of 18.40 per cent of carbon dioxide, 0.27 per cent of oxygen, and 81.33 per cent of nitrogen, although the atmosphere apparently was clear and normal. In a mine one can pass from good, breathable air to an atmosphere that will kill as quickly as one can dive from a board to deep water below. SOME INSTANCES OF ASHYXIATION BY GASES IN METAL MINES The following typical examples of comparatively recent instances of asphyxiation in metal mines were taken chiefly from reports of various kinds of the U. S. Bureau of Mines.

Jan 1, 1938

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Richard Hollis

The Mount Isa copper smelter was expanded in 1998 to a capacity of over 250000 t/y anode copper. This tonnage will be produced from a single stream consisting of an Isasmelt smelting furnace, and four Peirce-Smith converters - one of which was installed as part of the expansion project. During the course of the expansion project Mount Isa Mines Limited (MIM) signed an agreement with WMC Fertilizers Ltd (WMCF) to supply sulphur containing smelter gases over the fence to a new sulphuric acid plant to be built by WMCF. This will result in a further increase in copper production by reducing the time when smelting is curtailed by Air Quality Control restrictions. As well as the need to modify the primary gas system to connect to the acid plant, the hoods and crossover ducts and their support structures on the original three converters required replacement, and secondary ventilation was also needed to improve converter aisle hygiene. Each of these areas was addressed by the project. Preliminary ideas for carrying out the modifications were found to have a serious impact on converter aisle operations, and would have led to a production loss of over 50000 tonnes of copper. Following benchmarking in other copper smelters, a suitable construction plan was developed and carried out to minimise this loss. This paper describes the methodology and construction plan adopted.

Jan 1, 1999

By Frank Linforth

THE object of this paper is to present a brief outline of the methods of geologic mapping employed in the Geological Department of the Anaconda Copper Mining Co., at Butte, and to show by means of a few typical examples the practical nature of the results obtained. The extremely complicated geological conditions early encountered in Butte mining led mine operators to realize the necessity of accurate detailed geologic mapping as an aid to successful development of the ore bodies. The organization of the Anaconda Geological Department was undertaken in 1900 by H. V. Winchell, who, in conjunction with D. W. Brunton, worked out the essential methods of procedure which are, in the main, followed at the present time. Since the year 1906 the geologic work has been under the direction of Reno H. Sales, and in some respects the scope of the work has been slightly enlarged. Au excellent article describing the general equipment of the geological department was presented by D. W. Brunton at the British Columbia meeting of the Institute in 1905.1 His idea, that data collected underground and recorded should be put to practical use and not remain a mere " inventory of the company's underground possessions," is the keynote to the success of applied geology in Butte. The geologic notes are taken as soon as possible after the ground is broken so that any mistake in the mining may be corrected at once, or any particularly advantageous procedure may be suggested before any useless work is done. Taking the notes underground is a comparatively simple matter, but a few necessary precautions may be pointed out. The essential to success is that the notes shall show exactly what geological facts are disclosed. The observer must discriminate carefully between important and unimportant exposures in making the record, especially as regards the relation between veins and stringers, between faults and minor slips, or between the characteristics of veins of different ages. A simple color scheme has been adopted for making this record: Red pencils are used to indicate.

Jan 11, 1913

By C. P. Parsons

To properly account for the various characteristics of drilling muds obtained in different areas and geological horizons, it is necessary to study the composition of the mud from a chemical and physical standpoint as determined by the proportions and activities of the various solid contituents that are present in various states of division. Briefly summarized, science teaches that there are three states of division into which these solid constituents or particles may be grouped: namely, the suspended state, the individual particles of which are known as suspensoids; the colloidal state, in which the individual particles are termed colloids; and the crystalloidal state, wherein the individual particles are held in true solution and are termed crystalloids. The suspended state is one wherein the particles are fairly large and are present as molecular complexes, having none of the properties of colloids or crystalloids. Since matter varies in physical character and in chemical activities with its state of division, these coarser suspensoids do not themselves materially affect the physical or chemical properties of the solution in which they are suspended. On the other hand, they are distinctly detrimental in drilling muds and it is desirable that they be removed. Under the general classification of suspensoids are included sand, gravel and cuttings which contribute nothing to the colloidal stability or other desirable properties of the drilling fluid. As the state of division approaches but does not reach a molecular simplification, the term "colloidal state" is used in describing this condition. The colloidal state arises when one form of matter is in a very fine state of division and is distributed through a second phase. The material in the finely divided state is called the dispersed phase, while the liquid in which it is dispersed is called the dispersive phase. These particles of matter are in a colloidal state and will not settle out from the dispersive phase so long as colloidal conditions are stable. Moreover, they exhibit the property of having an oscillating movement around a central position in solution (the Brownian movement). In the third state of division, the crystalloidal state, the individual particles are held in true solution and are usually present as single molecules or ions. In a drilling fluid the water content of the fluid contains

Jan 1, 1931