Search Documents

By John Bell

Aim of Rock-Crushing Experiments THE aim of the laboratory experiments described in this paper was twofold: 1. To measure as accurately, as possible the maximum amount of crushing that can be effected by 1 hp. acting for 24 hr., by the two proposed methods for measuring the amount of crushing, namely: (a) by Rittinger's method; (b) by Stadler's method, based on Kick's law. 2. To show, if possible, that by one of these methods, the amount of crushing produced by 1 hp. in 24 hr. is a constant amount throughout a wide range in the diameter of the piece crushed, and that by the other method, the amount of crushing is a variable quantity over the same range of diameter; or else show that neither of the proposed methods for measuring the amount of crushing indicates a fixed relation between power and crushing and consequently a new method for computing this amount will have to be found to permit the establishment of a law of crushing. Experimental Methods Testing machines, calorimetric methods and commercial. types of rock-crushing machines were considered with reference to their value for measuring power used in crushing. The following electrically driven crushing machines, installed and available in the McGill Ore-dressing Laboratory and which had been used in previous rock-crushing tests, on the whole seemed especially suited to the investigation: (1) Comet "A" crusher; (2) 7 by 9-in. Dodge crusher; (3) 10 by 16-in. rolls. In later tests a 3 ½ -ft. Huntington mill was used.

Jan 2, 1917

Diamond wire rock cutting is the most widely used technology in carbonate stone quarrying owing to technical performance and block face quality. Interest is also growing for siliceous deposits. This paper deals with the problem of optimum wire utilization under restrictions regarding a set of variables and parameters. A computer program of general applicability has been set up with the aim of studying the most suitable combination of technologies and the effect on the technical and economic results of bench geometry, overall quarry yield, market -stone value, quarry size as well as the quantity, productivity and price of human and material resources and their organization in the elemental working cycle. Two quarrying problems are considered as significant instances a granite and a travertine quarry. The results are illustrated and discussed.

Jan 1, 1989

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By Fabio Amaya, Andrés Marulanda, Ramiro Gutiérrez, Alberto Marulanda

The behavior of a salt rock mass is strongly related to a creep phenomenon. The amount of creep depends on the level of stress generated in the underground excavation. Additionally, security conditions and the lifespan of an underground cavern excavated under this geological conditions depend on the evolution of creep. Based on the experience of the failure of the Old Underground Salt Cathedral of Zipaquirá(Colombia) and the construction of the new one, the theoretical framework to predict the creep behavior of a salt rock mass is explained. The theoretical formulations are calibrated based on actual observations of the material behavior to predict the lifespan of this striking structure.

Jan 1, 2003

By Connie S. Musulin

Radon concentrations in shallow uranium mines such as the Bureau of Mines experimental research mine are affected by barometric pressure changes. The radon concentrations show a significant correlation with absolute pressure; but over a period of days, a steady rise or fall in barometric pressure will result in noncorrelation of data. Fan shutdowns also affect radon concentrations, and an equation was derived to determine the time required for the radon concentration to return to normal after a fan shutdown, whether the ventilation is blowing or exhausting.

Jan 1, 1982

By Christopher Haycocks

Subsidence induced innerburden shearing and stress fields, whether active or passive, frequently contribute to significant ground control failures in overlying seams. In this paper proven multi-seam technology is used on upper seams to forecast and quantify the magnitude and severity of damage and the increased mining risk due to interaction. Increased upper seam ground control problems are demonstrated using hazard mapping which provides a viable technique for utilizing damage predictions in design.

Jan 1, 1986

By D. D. Porter, C. Fairhurst

Crack propagation in the region of a statically pressurized borehole is investigated to determine a role of the sustained borehole pressure following detonation in a blast. The case of a single-hole bench blast is reduced to a plate model, which is considered both theoretically and experimentally. Based on the principle of least work, it is hypothesized that the path of any crack in the plate will coincide with one of a family of maximum principal stress trajectories. These trajectories were computed, and critical experiments in glass, designed to test the effects of controlled crack origin and of changed trajectories from different loading configurations, confirm this hypothesis. It is concluded that under ideal conditions the crack path can be predicted and that cracks can be produced in the absence of either high-amplitude stresses or stress waves. Energy considerations for crack extension are discussed, and, based on the strain energy distribution, a relationship between hole burdens and spacings is revealed, a critical burden is demonstrated, and a maximum crater width is shown to exist.

Jan 1, 1971

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By Gerhard Mücke

Geothermal and operational reasons in the German coal mining industry make it necessary to an increasing extent to climatize coal faces and headings by means of refrigeration plants. Air coolers installed on coal faces as well as in gateroads play an important part in such climatization. They must transfer, under difficult conditions, the refrigerating capacity supplied by central or de-central refrigeration plants from the chilled water to the air in the workings. The performance data of two new types of coalface coolers and of two different types of gateroad coolers were measured in two testing stations under different thermo- dynamic conditions with dust-free fresh air. As air coolers must be installed particularly at working points with a high .dust load the heat exchanging surfaces are fouled for the most part causing an essential reduction of the refrigerating capacity. The investigations therefore were extended to measurements with a certain dust load in the intake air of the coolers.

Jan 1, 1980

By G. L. Oldright

DURING 1919, in the face of high cost for labor and supplies and a rapidly dropping copper market, the management of the Ohio Copper Co. of Utah was left with an orebody that had been shown to be very low grade, and a mill that could not make a satisfactory recovery, even by flotation, because a considerable proportion of the copper minerals was oxidized. About seven million tons had been mined by the use of a caving system, the best of the broken ore extracted and milled, and the nature and copper content of the rest of the orebody fairly well determined. The rock of the whole mine was shown to run between 0.3 and 1.3 per cent. in. copper. As, the Ohio Copper orebody lies at the contact of the original sandstone (now altered to quartzite) with the quartz monzonite intru-sion that was the source of the mineralization at Bingham Canon, the rock was thoroughly shattered. It was shown further that the rock was mostly quart-zite, with a few quartz-monzonite "fingers" projecting into it. Although some of the old cleavage planes had been healed by resilicification so as to leave some of the copper minerals disseminated in the rock, a large proportion of these minerals was distributed along the cleavage planes.

Jan 10, 1923

By Y. C. Kim, M Nataraja, J. T. Buckley, D. H. Tiktinsk

The Nuclear Waste Policy Act of 1982 (NWPA) assigns the U.S. Department of Energy (DOE) the responsibi1it.y of locating, constructing. operating, closing and decommissioning a nuclear waste repository. Prior to submittal of a licensee application to the U. S. Nuclear Regulatory Commission, the DOE is required by 10 CFR part 60 to conduct a program of site characterization for the site to be described in such application. Site characterization includes an exploration and research program in the field and laboratory to determine the geologic conditions and ranges of those parameters which are necessary for determining the suitabi1it.y of the site as a geologic repository. The information thus collected should be able to establish with reasonable assurance that the public and environment will be adequately protected from the hazards associated with a repository at the site. This paper demonstrates by example a geostatistical approach which, on the basis of the existing limited data base, can be used to evaluate (1) whether existing information on a certain parameter is adequate to be considered representative. (2) if additional information is required, where should the additional sampling or testing be performed, and (3) whether the new1.y acquired data along with the existing information constitute representative data.

Jan 1, 1986

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By John A. Herbst, Per-Olaf Samskog, Jan Bjorkman, Yi Chang Lo

The study described here is concerned with the development of a model for the simulation and optimization of a rod milllpebble mill circuit. A series of laboratory tests was conducted to investigate the effect of critical operating variables. The pebble mill model structure used was a population balance type which accounta for impact breakage and fines production from pebble wear. Model parameterization and verification were performed using data obtained in batch tests and in a plant test campaign. The model developed was found to provide accurate predictions of plant-scale grinding. The prediction errors are less than 21 for the product size and 31 for the mill power required to achieve that product with a mill volume scale-up of 14,000 to 1. These results indicate that accurate extrapolations from laboratory batch data to plant scale performance are poaaible using the population balance model and scale-up prediction procedures for pebble mill circuits as well as ball mills. Preliminary indications are that the new model developed here will provide vital input for pebble mill optimization and process control as well as pebble mill design.

Jan 1, 1990

By C Gunther

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By D. A. Sullivan, D. W. Fuerstenau

The authors investigated the comminution of quartz and limestone mixtures in a ball mill, showing that the distribution modulus of a comminuted material is the same whether it is ground separately or as part of a mixture. Analysis of the ground products indicates that quartz and limestone consume energy during ball milling in proportion to their mass fraction in the mixtures. Recently Schuhmann' made a significant contribution to comminution theory by proposing that complex comminution operations comprise the summation of many individual comminution events. By means of the single comminution event hypothesis, Schuhmann derived the Charles energy-size reduction relationship by considering that fragments of every particle crushed during a single impact have a size distribution characterized by the Schuhmann size distribution. In this paper, the size reduction of mixtures of solids in ball mills is analyzed by considering that size reduction occurs as many single comminution events. If a mixture of two materials is being ground in a ball mill, each successful impact of a ball with a particle of one material should yield an assembly of particles whose size distribution is characteristic of that material. Considering both materials to follow the Schuhmann size distribution equation, the size distribution of material 1 in the product is Where y is the weight percentage of material 1, which

Jan 1, 1962

By M. Karmis

Promoting a strong safety culture requires that the significance of unsafe acts be emphasized. This can be achieved vividly by accurate recreation of unsafe actions in the workplace, demonstrating explicitly how they resulted in a fatality or significant injury. Visual reconstructions of incidents can be realized today on personal computers. The approach described in this paper uses readily available PC software and hardware and results in output that can be presented to the intended audience using a variety of delivery methods. An actual incident involving a surface mining operation is reconstructed using Virtual Reality techniques. Use of the visualization approach to accident reconstruction as a training tool is discussed.

Jan 1, 2003

Mine geologists have access to an economic mineral deposit, production parameters and secure exploitation title. They are well placed to understand ore formation and should contribute to the effective exploration of company mine property. Application of their special skills has been curbed by pre-occupation with production duties and by company re-engineering, including staff reductions. Contributions to exploration have been diminished and personal development inhibited. Modified management is required. Participation in mineral system studies and in exploration research comprise part of the basis for the re-emergence of mine geologists on the exploration scene. Changes in investment strategies in the minerals industry may create new employment opportunities. With regard to estimation of resources and reserves, the competence of practitioners who are incapable of disclosing their methods in transparent terms is under question. Ethical standards are also under public scrutiny because of some notable malpractice. Independent auditing may hecome more intrusive. While understandable in a market context, it reflects poorly on the profession. More substantial effort in public communications can improve the credihility ofthe industry and equip practising mine ceolouists for snider responsihility.

Jan 1, 1997