Search Documents

By Owen Collins

In surface mining, designing patterns to reduce the probability of flyrock and optimizing fragmentation through powder factor calculations are important for safe, efficient blasts. The designed powder factor is established for the blast once parameters such as burden, spacing, stemming, and powder column height are determined. In practice, these parameters are usually constant throughout a production blast with row-to-row burden and spacing. However, challenges can arise with the introduction of an open face. Many variables could necessitate the adjustment of the face row to optimize blast results. Variables include drill accessibility, challenges with toes, overhangs, and geology. The approach is often, but not exclusively, determining how to keep a consistent powder factor from the open face through the body of the blast. However, the solutions used vary case-by-case and rarely are two blasts the same. Technology has improved the ability to deal with challenging face conditions. 3D modeling with the aid of drones allows the application of angled holes to be more effective and simpler. This is just one instance where technology has improved blast results. This paper will present solutions to challenging face conditions. Thoroughly analyzing instances where challenging open-face variables were met with an effective blast solution could help provide insight as to what yields consistent blast results.

Jan 26, 2026

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016

By Amélia de Santana Cartaxo

O objetivo deste trabalho foi analisar a influência causada pelo resíduo de Pedra Cariri após tratamento de calcinação em massas argilosas usadas para produzir tijolos de cerâmica vermelha, visando a melhoria e o barateamento dos produtos cerâmicos produzidos e mostrar outra alternativa de reciclagem desses resíduos. As matérias primas foram beneficiadas e formuladas em função do percentual de pedra cariri, caracterizadas por difração e Fluorescência de raios – X, conformadas, queimadas, sendo posteriormente submetidas a ensaio de flexão, absorção de agua, porosidade. A adição de resíduo propiciou o aumento do módulo de resistência à flexão, conforme maior temperatura. As análises de absorção de agua ficaram no limite e a porosidade diminuiu. A amostra de argila utilizada nesse trabalho demonstrou uma melhora em algumas propriedades devido a adição da pedra cariri calcinada, mostrando assim uma certa viabilidade para sua utilização na fabricação de tijolos de alvenaria, e seu uso sustentável é possível.

Oct 30, 2017

By Paolo Farina

Slope monitoring radar has emerged in the last ten years as a leading edge tool for monitoring movements in natural and engineered slopes, thanks to its ability to rapidly measure slope movements with millimetric accuracy over wide areas in any weather conditions, obviating the need to install artificial reflectors. In recent years, slope monitoring radar has experienced significant improvements in its performances, mainly thanks to the use of different radar technology, such as Synthetic Aperture Radar (SAR), able to overcome some of the limitations of the first generation of radar and to provide higher spatial resolution, longer working distances and faster acquisition time. One of the leading applications of this technology is today represented by slope monitoring within the surface mining industry. Prominent international mining groups currently employ slope monitoring radar, based either on Real Aperture Radar (RAR) and SAR technology, for active and background monitoring of open-pit walls. The main technical features of typical slope monitoring radar based on SAR technology along with their possible applications are presented in this paper along with recent case studies of successful slope monitoring in open pit mines.

Jun 1, 2012

By O Omidi, P D. Katsabanis

The effect of delay time on fragmentation has been discussed for a long period but rarely in a satisfactory and unbiased way. Despite the efforts of many researchers, delay selection for fragmentation improvement or optimisation remains a controversial issue. Large-scale tests have been plagued with scarcity and scatter of observations, while small-scale tests have been associated with boundary effects and energy losses. Theoretical work is often used to produce explanations for available measurements or tries to simplify wave propagation and wave interaction to guide observation and practical work. The present work analyses results obtained from a relatively large number of small-scale experiments in blocks made of grout, and re-analyses results of previous experiments, to conclude on the effect of delay on fragmentation. It is shown that the main contribution of the delay is found in the fragmentation of the larger fragments of the blast, while the small fractions show almost no effect. Samples, where copper liners were used to inhibit penetration of detonation products in the rock mass, showed effect of delay only when short times were used and steady but poor fragmentation when long delays were used. Based on small-scale experiments, it appears that the fragmentation is optimised when a hole fires prior to the radial cracks, produced by the previous hole, reach the free face of the blast. Gas penetration may result in the development of few more fractures that affect the fragmentation of the largest particles of the blast.CITATION:Katsabanis, P D and Omidi, O, 2015. The effect of delay time on fragmentation distribution through small- and medium-scale testing and analysis, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 715–720 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Stambolie

Mine planning processes are continuously evolving, increasing in complexity, and are required to be developed in shorter timeframes, often missing important steps in the process. Underground coal mines are also moving into more challenging environments, with the more favourable resources having been exhausted. In addition to traditional mine planning processes there is an increasing level of complexities associated with parallel systems including the preparation of Joint Ore Reserves Committee (JORC) compliant estimates (JORC, 2012 and Guidelines Review Committee, 2014) or seeking critical regulatory development consent to undertake mining. There is a clear link between geotechnical considerations and success of mining operations, and therefore it is essential that such considerations are elevated in both status and priority. It is obvious that geotechnical considerations are paramount in any mine, however it is imperative to accept that such considerations, and the collection of information relating to such, are undertaken from the onset of any mining project. CITATION:Stambolie, T, 2018. Elevating geotechnical considerations in the Australian underground coal industry and mine planning process, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 383–391 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Jerry Dimaggio, Ahmad A. Alhasan

With the increased vulnerability of transportation infrastructure to extreme events, resilience of transportation and infrastructure assets has become more critical. The term geotechnical asset applies to all infrastructure features constructed on, in, or of soil and rock. Depending on a specific application, a “geotechnical asset” may serve as a foundation of an asset, the asset itself, or both. This extent and variability of type (walls, slopes and structural foundations) makes them the most critical and challenging assets to manage and maintain. Moreover, geotechnical assets are vulnerable because of the number of internal asset variables and their susceptibility to accelerated moisture, erosion, and environment-related changes, which directly or indirectly impact the asset performance. This paper discusses the workflow and components of a recently developed resilience-based design framework of geotechnical assets. The core concept in Resilience-Based Design is to model the asset performance over time including possible repeated extreme events. These events result in accumulated progressive damage and accelerate the deterioration of the asset leading to progress serviceability or strength failure. The framework focuses on capturing the impacts of damage on the assets performance and incorporating preventive and corrective maintenance during the asset service life. The Resilience-Based Design (RBD) framework was then contrasted to the Allowable Stress Design (ASD) and Load and Resistance Factor Design (LRFD) frameworks in a significant case study of a soil slope stabilized using anchored drilled shafts. The slope was monitored over an extended period of time to capture the creep deformations of the stabilized slope. The design procedure will model multiple flood events using weather models developed for the area. Following the detailed case study example of the framework, the paper discusses the needs and procedures to implement the framework for a wide range of applications.

Oct 7, 2024

By D Morton, G Wallace

"Evolution Mining is the sole owner of the Mt Rawdon open cut operation, located 75 km south-west of Bundaberg in Queensland, Australia (Figure 1). It is a massive, volcanically hosted, low-grade gold deposit that exhibits excellent characteristics conducive to low cost mining and treatment.In 2014, Mt Rawdon began investigating initiatives to deliver higher mill throughputs without any significant capital expenditure or modifications to the existing processing plant. Various studies have shown throughput increases are possible by applying more blast energy, essentially by reducing feed size through blasting and leaving less work for the comminution circuits (Brent et al, 2013; Ziemski, 2011; Workman and Eloranta, 2003).Given that 53 per cent of energy used on a mine site is consumed by the comminution circuit, with only two per cent being consumed by drill and blast (Smith, 2013), it makes logical sense for a mining operation to align their drill and blast with their processing plant. The term commonly used when exploring this relationship is a ‘Mine to Mill’ program.Over nearly 12 months, various blasting options and Mine to Mill methodologies were tested at Mt Rawdon. Throughout the journey, it was abundantly clear that the Mine to Mill initiative is not as simple as making one technical or physical change and expecting an improvement. Rather, true sustainable improvements demand a paradigm shift across both the mining and processing cultures, where all departments are aligned and working towards the one outcome. This true overarching Mine to Mill mentality, enabled by Vistis™ 250 high energy bulk explosive, ultimately led to a sustained increase in throughput and profitability of the Mt Rawdon operation.Citation:Wallace, G and Morton, D, 2016. High Energy Bulk Explosives and Mine to Mill Focus – the Mt Rawdon Story, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 60–69 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By P. Shahinian, M. R. Achter

In a comparison of the creep -rupture properties of nickel in air arid in vacuum there is a reversal in relative strengths with variations in stress. At low stresses the properties are better in air while at high stresses they are better in vacuum. In the early stages of creep in a high stress test the specimen in air nzay have the lower creep rate but the one in vacuum is creeping at a lower rate in the later stages. A mechanism, involving two competing processes in terms of oxidation strengthening and weakening by surface-energy reduction, is proposed to explain these reversals. It had generally been assumed that, relative to their properties in air, the high-temperature strengths of metals would be increased in an inert atmosphere as a result of the elimination of the deteriorating effects of oxidation. However, several recent investigations have shown that the creep strength may be greater in air than in nonoxidizing gases. Pickus and Parker1 found that the creep rate of nickel was lower in air than in hydrogen or nitrogen. Internal oxidation was mentioned by Shepard and Schalliol as a possible cause for the longer creep life of Hastelloy C in air than in vacuum or helium. Sweetland and Parker, who observed lower creep rates for aluminum and copper in air than in helium, discuss the possible applicability of the dislocation-barrier mechanism to explain their results. Surface oxide layers may interfere with the escape of dislocations through the surface or with their generation there. In addition to showing the strengthening in air of low-alloy and stainless steel, and nickel and cobalt-base alloys, shahinian4 presented notch-effect data which indicate the role of stress concentrations; alloys of relatively low ductility were more sensitive to atmosphere strengthening when notched specimens were used. Although Bleakney's copper wires had a lower reduction of area in air than in vacuum, it is difficult to interpret his results in terms of strength changes since the stresses employed were not measured. In contrast to these data showing the strengthening in air, a number of investigations, most at relatively low temperatures, have demonstrated that the environment may cause a decrease in strength. These results are generally explained in terms of the effect of environment on surface energy. In a review of the subject, Benedicks and Harden use the concept of atomic bonding to explain how the adsorption of impurities would decrease the energy of a clean surface. A decrease in surface energy would facilitate the propagation of cracks or extension of the surface. Use of this mechanism is made by sato7 to explain the weakening of steel specimens bent in various liquids, by Potek and Shcheglakovs for the reduction of fracture strength of steel in molten metal, and by Benedicks and Harden for the reduction of strength of a variety of materials in a number of liquids. A similar explanation might be used for the results of Forestier and Clauss. The fracture stress of fine wires pulled in a variety of gases, including air, is lower than in vacuum. They attributed their results to the "tendency" for the gases to condense on the metal surface. That the strength of metals is affected by the type of gas in which the test is conducted has been demonstrated convincingly; the mechanism of the effect, however, is still uncertain. This investigation represents one in a series to explore the influence of variations in alloy composition and test conditions on the atmosphere effect in the expectation that the results would afford an insight into the processes taking place. To determine the effect of specimen composition, the present investigation was conducted

Jan 1, 1960

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By Orville R. Lyons

THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,1 but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913,8 by the United States Bureau of Mines in 1938,4 by Hancock in 1947,3 and by the national French research agency Cerchar in recent years.2 In 1950 Anderson' proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or ±0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1952

By Leo Horvitz

Microanalysis of near-surface soils for hydrocarbons is the basis of a method for locating gas and oil deposits. To substantiate this technique, evidence of vertical migration of hydrocarbons from petroleum accumulations is presented. Tabulated data relevant to hydrocarbon surveys conducted in several petroleum provinces are included. PEROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer' in Germany and by Sokolov in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas. Since 1936 work on petroleum exploration techniques of this type has been going on in this country. However, instead of determining hydrocarbon content of soil air collected in the field, investigators analyze samples of the soil itself for adsorbed and occluded hydrocarbons, which are released by suitable treatment and found in larger amounts than are the quantities reported for soil air. Difficulties often encountered in collecting gas samples in the field, moreover, are eliminated when soil is used as the sampling medium. Field Procedure: Sample locations are first surveyed over the area to be investigated. Care is taken to locate the stations at considerable distances from roads, pipelines, drilling wells, and other sources of contamination. The borehole pay be dug with a bucket-type hand auger or with mechanical drilling equipment. Lubricants are avoided in either case. When the desired depth is reached, a sample is brought to the surface, placed in a pint glass jar or can, and securely sealed. Sample containers are carefully labeled and delivered to the analytical laboratory. Generally a satisfactory sampling depth range is 8 to 12 ft. In some regions, however, satisfactory data are obtained from samples collected at much shallower depths. Such is the case, for example, in areas of west Texas where the limestone and caliche near the surface occlude hydrocarbons and prevent their rapid escape to the atmosphere. In carrying out broad reconnaissance surveys in search of large features, considerable time is saved by first taking samples one-fourth to one-half mile apart along profiles about one mile apart. If the analytical data indicate a hydrocarbon anomaly of interest, additional samples are taken to produce a more dense and uniform sampling pattern within the interesting area. This sampling program is particularly adaptable to areas that are sectionized. In areas covered with a network of roads, sampling along these roads facilitates the reconnaissance survey. Actual sampling density used depends upon areal extent of features expected. When flanks of piercement-type domes where accumulations may be only several hundred feet wide are sampled, stations are often no more than 200 ft apart. Analytical Technique: Of the hydrocarbons composing petroleum, only the more volatile would be expected to reach the surface of the earth. The analytical technique, therefore, was developed to determine only those constituents that exert a vapor pressure at room temperature. Actually, in near-surface soils, only a very small part of the hydrocarbons are heavier than pentane. Details of the analytical technique have previously been reported. Only a brief description of the methods will be presented here. A weighed portion of the sample, about 100 g, is first treated with an aqueous solution of copper sulphate and then with phosphoric acid in a partial vacuum. The copper sulphate prevents the reaction of the acid with carbides that may be present because the sample has been contaminated by auger particles. Such a reaction may produce spurious methane. The role of the acid is to decompose any carbonates present, thereby helping to release the hydrocarbons. The carbon dioxide is removed with potassium hydroxide and the flask containing the

Jan 1, 1955

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama, Ryuji Oinuma

"Recently, the arsenic grade in copper ores has been increasing year by year. Arsenic bearing minerals (enargite (Cu3AsS4) and tennantite (Cu12As4S13)) coexist with typical copper minerals such as chalcopyrite (CuFeS2). The removal of arsenic from copper ores that contain relatively high arsenic content is essential due to its adverse impact on the environment and the resulting economic consequences. In this study, arsenic removal and dissolution behaviour of Cu and As from enargite (Cu3AsS4) were investigated using ferric sulphate (Fe2(SO4)3) solutions containing sodium chloride under high pressure oxidation conditions. The effects of numerous parameters including the concentration of Fe2(SO4)3 and NaCl, temperature, total pressure, leaching time and particle size were studied while other variables such as pulp density and stirring speed were fixed at 100 g/L and 750 rpm. The results showed that more than 60% of the copper was dissolved in a 0.1 M ferric sulphate solution under the high pressure oxidative conditions, whereas the leaching rate of arsenic was less than 20%. SEM observation revealed that elemental sulphur was deposited on the surface of enargite forming a passivation layer and the residue was agglomerated. Those phenomena may cause a decrease in the copper leaching rate. It was found that more than 80% of copper was dissolved in the ferric sulphate solution in the presence of 0.34 M sodium chloride under the conditions optimized, whereas the dissolution of arsenic in the mixture did not exceed 2%. XRD analysis of the solid residues from the leaching experiments used ferric sulphate and mixtures of ferric sulphate and sodium chloride showed arsenic to be present as scorodite (FeAsO4).INTRODUCTION In recent years, there has been an increase of the arsenic (As) content of copper ores due to the gradual depletion of high grade copper ores. In some copper deposits, arsenic occurs in the form of minerals such as enargite and tennantite. The removal of arsenic in ores containing copper is critical to the production of pure copper and the management of the environmental challenges caused by the smelting process. Due to the environmental risk caused by arsenic emission and the deteriorated quality of the copper product, smelting of enargite concentrates is not an effective method for the extraction of copper (Padilla et al., 2010; Safarzadeh et al., 2014; Long et al., 2012). Therefore, a number of studies have been carried out to develop arsenic removal technologies from copper ores using various methods such as hydrometallurgy (Curreli et al., 2009; Tongamp et al. 2010), pyrometallurgy (Dalewski., 1999; Padilla. et al, 2012) and bio-oxidation (Ehrlich, 1964; Sasaki et al., 2010). Several hydrometallurgical leaching processes like sulphuric acid, alkaline sodium sulphide and sodium sulphate and ferric sulphate leaching have been developed to treat enargite ores and concentrates. The alkaline sodium sulphide leaching process has been developed for the removal of arsenic from enargite (Anderson, & Twidwell, 2008; Parada et al., 2014). The mechanism of the dissolution of arsenic from enargite in sodium sulphite solution is"

Jan 1, 2016

By S. Hartman

The Escalante Silver Mine in Southwest Utah produces an average of 71.000 kg (2.3 million troy ounces) of silver dore annually. Precipitates from a cyanide leach circuit are treated by either acid leaching prior to fusion or a direct fusion with nitre. Process development, plant experience, and a comparison of both methods will be discussed. Plant experience from the custom treatment of a gold/silver precipitate containing matte producing elements will also be covered.

Jan 1, 1989

The Porgera gold mine has made significant progress with the successful installation of a JK FrothCam image analysis system. The system is used to measure and control froth velocity on the scavenger circuit which has brought significant economical and operational benefits. The froth velocity signal, determined by analysis of the camera, is transmitted to the PLC that manipulates flotation cell airflow rate and cell level controllers to maintain a target froth velocity of 130 mm per second. Following on from a three-week trial installation in June 2000, a permanent installation was commissioned on the scavenger Outokumpu (OK150) tank cells. Further work is in progress on the rougher Wemco cells. This paper describes the evaluation of FrothCam Technology and its subsequent installation.

Jan 1, 2003

By Joseph Hoang, Nick Reed, Scott Wishart, Michael Lovitt

Marvel Loch Underground forms part of St Barbara Limited’s Southern Cross Operations which is located 360km (224 miles) east of Perth. Southern Cross Operations produces approximately 120,000 ounces of gold each year. Mining occurs in over 8 lodes using a variety of stoping methods including Uphole Benching, Long Hole Open Stoping, and Core and Shell.

Jan 1, 2012

By Kremena Dedelyanova

The paper presents research of mechanism for the creation of air bubbles in vibratory a column flotation machine. Factors are discussed that influence the increase in the duration of the bubble in the area of contact with the mineral particles. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in a vibratory column flotation machine is determined.

Aug 1, 2013

By F. L. Pellet, S. Maiolino

"The determination of rock bolt contribution to reinforced joint shear strength is still a challenge, especially for assessing reinforced rock mass stability. For this purpose, several experimental studies have been performed during the last decades, mostly on small scale rock joint and bolt specimens. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for. For this reason full scale lab tests are required as an alternative to in situ tests for which boundary conditions are more difficult to control.In this paper the results of an experimental program carried out with a large shear box, dedicated to test bolts in full scale conditions is presented. Different rock bolt diameters and different rock bolts inclination with respect to the shear plane were tested Experimental results were satisfactorily compared with an analytical model which is able to compute the contribution of the rock bolt to the shear strength of the joint as well the associated displacement of the joint. These conclusions allows us to validate the model in order to help the designer of reinforced rock engineering structures, such as slope or underground openings, to precise the optimum installation of rock bolts. INTRODUCTIONFully grouted rock bolts are commonly used for rock masses reinforcement to ensure the stability of rock slopes and underground cavities. For this purpose, the determination of rock bolt contribution to reinforced joint shear strength is of the utmost importance. During the last decades, several experimental studies have been performed to investigate the behavior of bolted rock joint. For obvious reasons, almost all the experiments were achieved on small scale bolted rock joint specimens (Bjurström, 1974; Azuar, 1977; Dight, 1983; Egger & Fernandes, 1983; Schubert, 1984; Spang & Egger, 1990; Egger & Zabuski, 1991). These studies made it possible to assess the influence of different parameters such as the bolt’s diameter, the number of bolts, the angle between the bolt and the joint, the nature of the rock, the friction and the dilatation angle of the joint. However, to accurately assess the rock bolt contribution, scale effect has to be accounted for (Vallier et al., 2010). For this reason full scale lab tests have been performed as an alternative to in situ test for which boundary conditions are more difficult to control."

Jan 1, 2015

By Lin Yang, Yuanbo Zhang, Zhuoxuan Li, Guanghui Li, Jinghua Zeng, Tao Jiang

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 oC, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Jan 1, 2015

By Ivan César Lopes Diniz

Stretcher Reducing Mill (SRM) is a mill used in production of tubes. It is composed with a set 24 of stands responsible to define the final outside diameter (OD) of tubes. External appearance is critical in this process even though this requirement has no effect on mechanical properties. For this reason, an investigation of external longitudinal marks mechanism is in progress using 6 Sigma methodology. This paper is a part of the investigation with focus on the rolls and its mechanical properties. Destructive tests were performed in the rolls and compared with the project. After a detailed investigation, it was concluded that rolls were out of hardness specification and the project was poor of information. A new supplier was developed (internal market) based on the new project and all requirements were achieved as demonstrated in this paper. A monopolistic market for this product in VSB (Vallourec Soluções Tubulares do Brasil) was eliminated. Concerning the effect on the external longitudinal marks, the new rolls developed within hardness range minimized the mechanism of wear on rolls surface and consequently on tubes surface. A collateral effect has been faced, but still better than external longitudinal marks on tubes surface. The quenched and tempered rolls are more sensitive for process variation, mainly linked with cooling system and temperature of tubes (mechanical resistance for deformation). Nevertheless, a new material has been aimed focusing on reduction of rolls breakage with good tenacity and affordable cost.

Oct 4, 2019