Search Documents

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By Bernard J. Scheiner, R. J. Wesely, Cy E. Jordan, A. D. Zunkel, Gary M. Wilemon

The U.S. Bureau of Mines has investigated leaching of off-grade western United States phosphate deposits using sulfuric acid (H2SO4) in the presence of methanol. A combination of ore grinding followed by sulfuric acid in methanol leaching extracted over 80 pct of the phosphate. This leaching technique significantly limited the dissolution of iron, aluminum, and magnesium impurities and produced a phosphoric acid that was well within the desired limits for these impurities. The dissolution rate of phosphate rock in the sulfuric acid methanol system was significantly slower than the conventional aqueous sulfuric acid dissolution. Initially dissolution of the phosphate particle was controlled by the amount of surface area available to the sulfuric acid reactant. After about an hour of leaching, phosphate dissolution was slowed almost to a stop, limited by the rate of ion diffusion through the calcium sulfate barrier layer surrounding the unreacted phosphate particle. Consequently, the ore was ground below 38-pm to increase the particle surface area available and improve the overall dissolution kinetics and extraction. In addition, the sulfuric acid was slowly metered into the reactor to prevent any excess heat from the mixing of acid with the methanol from simulating the formation of methyl sulfates. The formation of methyl sulfate ultimately lowered the overall phosphate extraction by exhausting the supply of available sulfate ions for the dissolution reaction. Subsequent evaporation of the methanol from the product acid decomposed the methyl sulfates leaving undesirable sulfate ions in the product acid. Slow acid addition to the reactor provided high phosphate extraction and limited the amount of sulfate in the final product acid.

Jan 1, 1993

By E. S. Bardwell, Roy H. Miller

During the period extending from May, 1922, to September, 1923, the copper-refining furnaces of the Great Falls Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont., were operated exclusively with pulverized coal as fuel. The installation was made first as an experiment. It proved successful from the start and was abandoned solely because fuel oil from the Sunburst field became available at a price sufficiently low to be more desirable from an economic standpoint. The equipment required for pulverized coal has, however, been kept intact and is available for immediate use should the oil supply fail. Inasmuch as pulverized coal had been used on two large reverbera-tory smelting furnaces and was, at the time we were considering its application-to the copper-refining furnaces, being used on the Wedge furnaces roasting zinc concentrate for the electrolytic zinc plant, we were equipped with a coal-pulverizing plant of ample capacity to supply pulverized coal for the furnace refinery. The only problem was to devise suitable means for transporting pulverized coal from the pulverizer plant, located in the smelter building, to the refinery about 3000 ft. distant and about 150 ft. above the level of the pulverizer plant. When studying this installation, it should be borne in mind that the layout represents an adaptation suited to the existing conditions at this particular plant. The installation was entirely satisfactory and uniformly dependable but might be modified to advantage from an operating point of view if an entirely new installation were being planned. Fuel Supply The use of the local coals, high in ash and sulfur, was abandoned some time before coal-dust firing was attempted. Local coals from the Great Falls field carrying an average of 4 per cent. sulfur and 22 per cent, ash were used with fair success in the small furnaces in use prior to 1916. In the 250-ton furnaces, however, the time lost in grating and removing clinker from the fireboxes, as well as the difficulties incident to the high-sulfur content of the fuel, became serious and recourse was had to the

Jan 1, 1927

By D. Pearson

INTRODUCTION In 1975 278x10 3 tonnes of zinc was consumed in the United Kingdom, of which 69.3x10 3 tonnes was obtained from secondary sources. Of this secondary zinc 37.7x10 3 tonnes was used in brass making, the remainder was used in non metallic applications - eg oxides and salts. Many forms of zinc-bearing wastes arise, for example as galvaniser's drosses and residues, fumes from ferrous and non-ferrous metallurgical processes, and filter cakes from rayon manufacture and metal finishing. In the case of zinc-bearing dusts and fumes, the quantities available for recycle are at present restricted by the failure to collect them efficiently, hut environmental factors are leading to improvements in gas cleaning, with the result that quantities collected will increase and then exceed those required for the production of chemicals, so that some dusts may either have to be dumped or processed to metal. The recovery of zinc from steelmaking dusts is practised in W. Germany (1) and Japan (2) employing processes based on reduction in rotary kilns in order to produce sponge iron and a zinc- rich oxide suitable for feeding to the zinc-lead blast furnace. Although the zinc-lead blast furnace is the only zinc-making process used in the UK, no similar treatment of steelmaking dusts is carried out, a pilot scheme was tested by the British Steel Corporation, but development was abandoned for economic reasons. It appears to be cheaper to pelletise suitable dusts and export them for treatment elsewhere.

Jan 1, 1981

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By H. M. Howe, E. C. Groesbeck

That the quiescence of a liquid while it is solidifying should favor the formation of columnar crystals, normal of the cooling surface, is seen readily on considering the mechanism of solidification. First, each particle of any composite liquid, whether it be an aqueous solution or a molten metal, in solidifying splits up into two parts, different in composition and hence in fusibility. One part is infusible at the existing temperature, and hence solidifies, and in general attaches itself to the inclosing walls of metal which have already solidified; A, Fig. 1. The other part is fusible at the existing temperature and hence remains molten. In the case of carbon steel, the part of each drop which actually solidifies is poorer in carbon than the drop itself was before it began to solidify, and this impoverishment of the solidifying half-drop enriches the other half-drop in carbon, and thus makes it unfreezable at the existing tern- By this mechanism there arises during solidification a "littoral" or shore layer of liquid B, Fig. 1, bathing the already solidified walls, and more fusible than either those walls or the great remaining central mass of liquid or " deep sea " C, from which it separates them. It is essential that we grasp clearly this conception of a fusible littoral molten layer coating the already solidified walls and separating them from the deep sea. Meanwhile heat is flowing rapidly outward through these walls, its escape cooling them, so that if any given particle of the deep sea metal could get past this littoral layer and come into contact with the solid walls, it would in turn solidify, and like its predecessors would split up in solidifying into a less fusible half-drop which would attach itself to those . walls and a more fusible one which would remain molten. Thus we see

Jan 1, 1920

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By William Gleason

While a fleet of 100 t (110 st) haul trucks were busy removing overburden from the open pit mine in the distance, a host of dignitaries, including congressmen and California state representatives, gathered for Molycorp?s official groundbreaking ceremony at the Mountain Pass Mine on April 20. The mine, recognized as arguably one of the richest rare earths deposits in the world, is at the center of Molycorps? strategic ?Mine to Magnets? plan. It aims to secure America?s future supply of rare-earth-dependent technologies by developing a strong domestic rare earth industry. Molycorp identifies rare-earth-dependent technologies as those that cannot be produced without rare earth materials. The list of these technologies is long and growing. It encompasses everything from personal electronics and batteries for hybrid cars to permanent magnet generator wind turbines and national defense applications.

Jan 1, 2011

By C. F. Kaiser

The Broken Hill proprietary company Limited grate kiln pellet plant (1) located at Whyalla in South Australia commenced production on May 13, 1968. During commissioning, about 25,000 long tons of fluxed pellets were produced. Plant performance was satisfactory and acceptable under the plant guarantee. For production reasons, it was necessary to curtail the fluxed pellet run and revert to the production of acid pellets. In 1970, some 250,000 long tons of fluxed pellets were produced under varying operating conditions to determine the requirements for optimum quality pellets at acceptable production rates. In excess of 180,000 long tons of these fluxed pellets were exported to Japan. Problems experienced in production of the fluxed pellets are detailed, and the quality of the fluxed pellets compared to that of normal acid pellets produced at Whyalla. Brief Plant Details Run of mine ore treated was predominantly soft and friable and contained an average of 66 per cent Fe, 1.7 per cent Si02 and 1.8 per cent Al203. The main iron mineral in the ore was hematite with some martite also present. Plant feed was ground dry in ball mills 11 ft in diameter by 29 ft long to a Blaine surface area of 1600 sq.cm/g and the ground ore was wetted in a pug mill. Balling was carried out in balling drums 10 ft in diameter by 32 ft long. Induration equipment included an eighteen windbox grate 12 ft 2 in. wide by 164 ft 1 in. long, a rotary kiln 18 ft 6 in. diameter by 118 ft 8 in. long and an annular cooler 50 ft mean diameter by 7 it wide.

Jan 1, 1972

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By Mohsen Elsayed, Amr Sallam, Ahmad Mohamed, Xuebing Zheng, Mohamed Alrowaimi

The foundation is an essential component of the wind turbine that ensures continued operation under stable and safe conditions. Both shallow and deep foundations are utilized to support wind turbines including gravity spread foundation, anchor foundation, pier or drilled shaft foundation and pile and pile cap foundations. Conventional methods were typically utilized to design the wind turbine foundations. With the advances in numerical modeling in the geotechnical field, foundation designers may utilize numerical analysis to design wind turbine foundations. Geotechnical numerical packages allow modeling structural components and soil-structure interaction that is usually neglected in conventional methods. Furthermore, the subsoil conditions, geometries, stress-strain behavior, boundary conditions and load staging can be modeled, minimizing the assumptions and generalization. This results in better understanding of the stress strain behavior of the foundation leading to optimized foundation designs. This paper includes a brief review of current foundations used to support wind turbines with an emphasis on post tensioned single pier foundations. The current conventional foundation design methodologies and state-of-the-art foundation design utilizing numerical modeling of the single pier foundation will be discussed. Two case histories where the single pier foundation, designed using numerical modeling, were utilized to support the wind turbines will be presented. INTRODUCTION The foundation is an essential component of every wind turbine that ensures continued operation under stable and safe conditions. Turbine manufacturers provides load specifications for designers to be utilized for wind turbine foundations design. Loads include bending moments, torsional moments, lateral forces and vertical forces in both operational and extreme wind conditions. Essential specifications under seismic conditions might also be provided in seismic prone areas. Turbine manufacturers also include foundation design criteria including minimum rotational stiffness, minimum horizontal stiffness, maximum allowed inclination and maximum allowed lateral movement under both operational and extreme loads. Geotechnical explorations and evaluations are typically performed at early stages of the wind development projects. The field explorations usually include Standard Penetration Test (SPT) borings, Cone Penetration Test (CPT) Soundings, geophysical surveys, and laboratory tests to define soils stratification system and soil strength and compressibility characteristics. The most critical soil parameters for turbine foundation design are shear strength parameters (cohesion and friction), shear modulus, Poisson’s ratio, and unit weight. The depth to the groundwater table is also a crucial parameter in design. Advanced field explorations techniques such as Dilatometer Tests and Pressuremeter Tests may also be utilized. Laboratory tests for foundation design typically include index parameters, consolidation and triaxial tests.

Jan 1, 2019

By Fred W. Gordon

The heading of this paper was prompted by the knowledge that experience, up to this time, seemed to indicate that smaller furnaces were preferable for smelting the material of this section. Since the reasonable success thus far achieved by the first furnace of this plant tends to change the above opinion, and unsettle the generally-accepted views of furnace-men as to "weak " coke, a few words as to the design of the plant and the mode of operation adopted may prove interesting.

Jan 1, 1889

By D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast- holes in magnetic taconite at the preliminary taconite plant of the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing ma- chine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1.

Jan 7, 1951

By Lightfoot BW, Bultitude-Paull J

The Sirosmelt top submerged lancing system has many applications in the smelting of base metal and complex materials. It has particular advantages for smaller scale smelting and the treatment of recycle materials in smelters where its low capital and operating costs and its operational flexibility are of immediate benefit. The system can be fueled by oil, gas or coal, as well as by mixtures of fuels. For many applications, the use of coal as a fuel has operating cost advantages over oil and gas, but conventional pulverised coal feeding systems entail very large capital expenditure and this militates against the use of coal. The methods available for improving on conventional technology for coal firing of Sirosmelt systems are discussed and operating experience with alternative systems are outlined. The use of coal as a reductant in the Sirosmelt system is also discussed.

Jan 1, 1987

By Howard M. Wells

The investment worth of a mineral deposit can only be realistically evaluated in relation to specified engineering design criteria which fully detail the proposed method of exploitation. The operational design of a mine falls essentially within the technical discipline of the mining engineer, under the constraint that the technical design should be aimed at optimizing the financial attractiveness of the project. In the case of a marginally viable proposition it becomes vitally necessary to identify the best set of design parameters which together will add up to an optimum investment proposal. This paper examines some fundamental logic of optimization for a "wasting asset" type of investment such as a mine, with special reference to the rate of annual production and the strategy of selective mining.

Jan 1, 1979

By Henry U. Ross

The behaviour during reduction of iron-ore pellets and sinters was investigated. Several methods for the preparation of agglomerates and their reduction were tried. Commercial agglomerates from world-wide sources as well as experimental samples were tested. The effect of coke additions to pellet and sinter plant feeds was given special consideration. An analysis of the test results has helped to explain many of the phenomena associated with the reduction of iron-ore agglomerates such as swelling, loss in strength and wear resistance, changes in porosity, changes in mineralogy and the formation of metallic iron and slag. A double-layer pellet with all of the coke concentrated in the core proved particularly interesting. Although large quantities of coke showed that partially reduced agglomerates containing metallic iron could be produced in the laboratory, the problem of producing reduced pellets and sinters by the existing agglomerating processes still remains.

Jan 1, 1977

By S Mundell, J Armstrong, M Evans

"Automation is a common goal within the coal industry for reasons such as efficiency, reliability and sustainability. However, it requires standards and frameworks so business systems can communicate effectively. Automation of sample analysis processes has been difficult to establish due to a lack of direct business system communication between commercial laboratories and mining companies. This has resulted in manual procedures that have contributed to problems relating to analysis instructions, sample identification, results formats and visibility of status.These problems result in loss of data and confidence in data validity, loss of process efficiency and inability to react to issues. An Australian Coal Association Research Program project (Evans, Armstrong and Arboleda, 2014) has addressed these issues through the Coal Quality Data Exchange methodology for direct business system communication between coalminers and commercial laboratories to optimise the transfer of coal quality data.The benefits to the coalminer of the framework are:increased clarity and auditability of what is being sent to the laboratory and what was requestedreduced potential for error introduced through manual transcription tasksincreased speed of loading of analytical results to the customer Geoscientific Information Management Systemimproved turnaround time for analytical resultsincreased knowledge about what took place in the laboratory with respect to the determination of the analytical resultsincreased visibility of the status of a ‘work order’. The benefits to the technology companies and commercial laboratories is a common framework on which to build a sustainable solution that gets away from the multitude of formats catered for today and time consuming manual processes. The common framework significantly advances the future possibilities for the automation of sampling and analysis processes in a production environment.CITATION:Armstrong, J, Mundell, S and Evans, M, 2014. Automating communications between laboratories and mines – a case from the coal industry, in Proceedings Ninth International Mining Geology Conference 2014 , pp 351–360 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of grinding conditions on galena flotation and galena separation from pyrite. The changes occurring on the mineral surface during grinding were investigated by EDTA extraction and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the type and amount of oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite flotation but had little effect on galena flotation. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled.Grinding conditions had a large effect on the flotation of the galena particles of different sizes. Flotation of fine galena particles (-10 µm) was depressed by iron oxidation species derived from the grinding media. Chromium grinding medium decreased the production of iron oxidation species and therefore increased the flotation of fine galena particles."

Jan 1, 2003