Search Documents

By M. K. Larson, J. K. Whyatt, R. B. Langston, J. C. Johnson, H. Kirsten, T. M. Brady

An experiment is described in which hollow inclusion cells (HICells) were used to measure stress in a jointed rock mass during drift development at the Stillwater Mine, Nye, MT, USA. Two HICells were installed in the footwall approximately two drift widths ahead of the face. One HICell was over cored and then immediately tested in a biaxial chamber. The other HICell was left in place and monitored as the drift was excavated in three advances, each one-half the width of the drift. Strains were recorded hourly by a datalogger. Results show that there was little stress change during the first and second drift advances, but that a large stress change occurred after the third advance. The measurements also showed that the in situ principal stress directions lined up with regional geologic structures. Stress changes during face advance were likely caused by deformation along localized joint sets and inelastic deformation near the face.

By Brian S. Prosser, Ian J. Duckworth

With the trend in the coal mining industry pushing towards improved productivity and greater production, the number and size of longwall panels is increasing rapidly. The development and mining of large longwall panels causes unique problems in the provision of adequate ventilation at the working faces. Because of the transient nature of the longwall panel, and the difficult field conditions for ventilation measurements, detailed pressure and volume surveys are often not conducted around the longwall circuit. This is unforlunate because the highest resistance airway in longwall mines is typically the longwall tailgate, which frequently represents the only unregulated split in the ventilation network. This paper examines data collected from ventilation studies of longwall panels at nine mines. The variation in airway resistance, ventilating pressure and airflow is examined and compared with specific factors such as airway dimensions, ground conditions and support type used.

Jan 1, 1997

By K. Irmscher

During the last years, using modular computer models on the software and distributed computer capacities on the hardware side has become quite common in the mining industry. When tackling real mining problems under the condition of heterogeneous systems, however, some problems become obvious: the incompatibility of the heterogeneous platforms in connection with the heterogeneously structured information and the necessity of interpreting the data. Knowledge based approaches are employed for solving different planning problems in the field of mining industry. The main problems here consist in the knowledge representation and data acquisition. Starting point of the investigation form classifications of mining planning problems and the corresponding models which can be transformed into information models for evaluation. With help of an expert system a practical solution is represented. Distributed systems with mobile computing and communication facilities for immediate access can be used as an additional support for planning and processing. On the base of public or private computer networks (including mobile networks) the foundation is given for a computer supported treatment of planning tasks. Additionally the use of teleworking scenarios in regions of mine planning and data collection in geological applications is prepared. Foundation forms a workflow system on an object-oriented distributed platform.

Jan 1, 1996

By Wayne Stange

Due to the availability of user-friendly microcomputer based packages, the use of simulation is increasing.. Users have however encountered problems inherent to the structure of sequential-modular simulators. These are the difficulties associated with estimating parameters for arbitrary' models and the solution of design and optimization problems. The implementation of an optimization routine in the simulator MicroSim has facilitated the solution of such problems. The literature indicates that more efficient numerical techniques for solving optimization problems than those presently used in MicroSim are available. These techniques, together with user-interfaces which allow such problems to be specified easily by users, will result in the development of simulators much more powerful than existing ones.

Jan 1, 1989

By Harold M. Mooney

RESISTIVITY measurements for determining depth to bedrock, water table, and other geologic discontinuities have had only limited success. Many of the difficulties can be attributed to complex geology and to basic limitations of the method; current flow through a continuous medium is a diffusion phenomenon, emphasizing irregularities near the source and smoothing out those at a distance. Some of the failures, however, are due to careless field work and incompetent interpretation. A forthcoming publication1 may help to reduce difficulties of this sort. The writer here attempts to bring order into the multiplicity of interpretation methods and, to a limited extent, to evaluate them. For all methods, the field data to be interpreted consist of apparent resistivity values plotted against electrode separation, Fig. 1. The interpretation should give depths to one or more geologic horizons. Direct currents and the Wenner four-electrode configuration will be assumed, since these are widely used, although the interpretation problems remain essentially the same for other electrode configurations. Alternating currents higher than, say, 20 cycles per second introduce complications beyond the scope of this paper. Three approaches to the interpretation problem have been used. These may be called empirical, theoretical curve matching, and direct. Many techniques have been proposed, but each can be reduced to one of these approaches and to a single geologic idealization. This idealization rests on the following assumption: the earth in the limited volume of interest can be approximated by a horizontal sequence of layers, each homogeneous and isotropic in its electrical properties. This seemingly restrictive assumption has proved to have practical value, although future work should aim at removing some

Jan 1, 1955

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

By P. M. Pincheira Brown

The widely accepted inverse relationship between copper prices ail stocks, has been commonly used by analysts to explain the behavior of the copper market and to forecast film copper pries. However, empirical data have not shown such a clear relationship between copper prices and stacks. Existing evidence only indicates a weak tong-nut relationship that vanishes in some periods. In this paper a simple comprehensive model is provided which explains both parallel and opposite direction movements between prices and stocks. Former are explained mainly by stocks demand expansions-contractions while the latter are in essence due to increases in the supply curve. Furthermore, econometric estimations are provided, thus giving a powerful tool to forecast and explain price developments of the copper market.

Jan 1, 1999

By B. W. Frazier

AT a recent meeting of the North of England Institute of Mining and Mechanical Engineers, during a discussion upon the compression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

Jan 1, 1874

By J. Brent Hiskey

INTRODUCTION Metal electrodeposition processes are of fundamental technological importance to a number of fields. Electrorefining, electrowinning, electroplating, and electrogalvanizing have all been the subject of intense study for over a century. More recently, electrochem- ical deposition has played a critical role in advances in microelectronics and lately has been an enabling technology for the production of certain nanostructured materials. Electrometallurgists have most frequently been concerned with the structure and morphology of massive deposits. For example, in metal recovery steps such as electrorefining and electrowinning, deposits demonstrating adherent coarse-grained characteristics are most desirable. In the case of electroplating, a bright fine-grained, tenacious and strongly adherent deposit is required. The fabrication of microelectronic devices and the production of nanoscale structures such as nanoparticles, nanowires, and nanorods requires a keen understanding of early stage deposition effects. The initial stages of metal deposition, usually referred to as electroclystallization, are fundamentally linked to nucleation and growth phenomena. Early stage deposits are typically very ordered. Whereas, bulk metal deposition structures are much more ran- dom. In both cases, the discharge of a metal ion at an electrified interface is represented by simple cathodic reduction as follows: [ ] Me(H2O)xn[ ] is a hydrated metal ion residing in the bulk solution and Me is the metal atom occupying a crystallographic lattice position. A similar reduction reaction can be

Jan 1, 2005

By R. G. Mallon, R. L. Braun

Primary copper-sulfide ore deposits that are well below the water table can be chemically mined by in-situ high-pressure leaching. The leaching is accomplished by pumping oxygen gas into the bottom of a large underground flooded column of rubblized ore. Part of the injected oxygen dissolves under the high hydrostatic pressure in the column. With a high enough injection rate, the excess oxygen gas induces a convective circulation of oxygenated solution within the rubble column, which transports dissolved oxygen throughout the system. At elevated temperatures, this results in a relatively rapid dissolution of the copper minerals. A method of calculating the leaching rates is presented. The calculation is done by means of a finite-difference computer code that couples all of the processes relating to copper leaching, convective circulation, and the injection, dissolution, and consumption of oxygen. Results of the calculation for a typical case show that over 70% of the copper can be extracted in less than six years with good efficiency in oxygen utilization.

Jan 1, 1976

By Dale Preece, Stephen Chung, D. Scott Scovira

The DMC_BLAST (Distinct Motion Code) has been developed to model rock motion and displacement during the gas expansion phase after the detonation of an explosive in a borehole. Recently, a designated delay firing order algorithm was written into the DMC_BLAST code. The model can now be used to analyze rock mass displacement for a V-cut, center opening, or sinking cut initiation sequences. This new feature allows the investigation of the effects of delay firing order on rock displacement when blasting complex inter-bedded and ore-waste structures. The model provides important ground movement and mixing indicators for dilution control in surface gold mining relative to the initiation sequences employed. Echelon blasts as compared to center opening type blasts show differences in their internal muckpile displacement. These displacement differences can be important to operations that mine narrow strike driven ore bodies. The model also has applications to through coal seam blasting and demonstrates that down-dip blasting is a better alternative than up-dip blasting. There is less disturbance to the dipping coal seam and less mixing of the rock and the coal.

Jan 1, 2000

By Thomas B. Dellinger

Since 1950, rotary-drilled, large-diameter holes, "big holes", with depths to over 300 ft and diameters of over 30 in., have become numerous and widespread. 50 such holes have been drilled for access shafts to LPG mined caverns. Over 70 holes have been drilled for various other commercial activities. Over 150 holes have been drilled by the AEC for atomic testing purposes. These holes have ranged up to 300-in. diam with 1600-ft depths, 120- in. diam with 570-ft depths, and 72-in. diam with 4800-ft depths. Equipment is now available to drill a wide range of big holes for varied requirements. At least a dozen drilling contractors are participating or have participated in the drilling of big holes. The accompanying tables show pertinent historical, technical and economic data on over 250 holes. The purpose of this paper is to present a review of the big hole drilling equipment available, a compilation of the available data on large-diameter holes, to show the experience obtained to date and to show that big hole drilling is feasible and available to the industry.

Jan 12, 1965

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By J. A. McKeown, B. M. Sanders, A. Dadgar, R. H. Sergent

This paper describes the leaching of gold with Geobrom® 3400 from a very rich (6.2 kg/tonne) black sand concentrate and its subsequent recovery by ion exchange resins and solvent extraction. The dissolution of gold from black sand ranged from 94 to 96%. Gold loadings and recoveries of nearly 100% were achieved by both ion exchange and solvent extraction methods. The kinetics and equilibrium of loading gold onto ion exchange resins and its elution from the resin were studied. The commercial ion exchange resins PAZ®- 4, DOVEX®- 21K, and Amberlite® XAD- 7, and Great Lakes Chemical experimental GLR-30 were evaluated in this work. Diethylene glycol dibutyl ether was used in all the solvent extraction work for gold recovery from Geobrom leach solution. The consumption of Geobrom was about 130 kg per tonne of the concentrate processed. Therefore, the cost of lixiviant to extract 3.11 x l0-2 kg of gold from the black sand was only about $1.00. Based on the electrochemical regeneration of bromine, the economics of bromine process vs. cyanidation were investigated.

Jan 1, 1990

Throughout the Kalgoorlie Field the dominant factors influencing all planned exploratory work are: firstly, the general geology of the district, and, secondly, the lode fracture pattern. Superimposed on these, there are innumerable faulting problems which tend to complicate the search for ore.In this paper it is proposed to deal primarily with the lode fracture pattern and to touch on the general geology only insofar as it affects ore distribution. So much has been written on Kalgoorlie geology that it would be impossible to review the literature adequately in a brief paper such as this. The basic facts of rock types and rock distribution are well established and the broad structure of the field is known in the central portion, though it is less well established towards the northern and southern ends.The latest descriptions of the general geology are those of Stillwell (1), and Gustafson (2), -and these represent the basis of current knowledge.GENERAL GEOLOGY.The field is six miles long and about one mile wide, the long axis trending north-west. The "Golden Mile," or heart of the mining 'area, covers a length of three miles in the southern section, and consists of a central core of quartz dolerite greenstone which merges into uralitic quartz 'dolerite on its western margin. The uralitic quartz dolerite is derived from an original quartz dolerite by a low grade...

Jan 1, 1948

By R. W. Raymond

The death of Professor Blake removes the oldest of American economic geologists and mining engineers, and deprives this Institute of one of its earliest and most illustrious members. To many of us it brings a personal loss also, the loss of a friend. William Phipps Blake was born June 21, 1826, in New York City. His father, Elihu Blake, was a surgeon-dentist of eminence, a direct descendant of William -Blake, who settled in the Massachusetts Bay Colony about 1630. He was prs pared for college at private schools in New York, and entered the Sheffield School of Yale, where he was graduated as Ph.B. in the chemical course, class of 1852, the first graduating-class of the institution. In the same year he became chemist and mineralogist of the New Jersey Zinc Co., and chemist of chemical works at Baltimore, Md. In 1853, he started the Department of Mineralogy of the World's Fair at New York City. In 1854, 1855 and 1856, he was mineralogist and geologist of the United States Pacific Railroad Surveys of Willianlson, Pope, and Whipple, and for the War Department at

Jan 1, 1911

By William P. Diamond

Production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 m' to 10.1 x 106 m3. Peak production rates were generally about 0.03 to 0.06 x 106 &/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to several factors including: completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance, is hole location. Holes on the ends of the panels, where overburden strata are in tension due to the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location which is in compression. Analysis of gob gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 1995

By Gordon M. Matheson, Charles V. Logie

The current state-of-the-art design of mine pillars can be grouped into empirical and numerical design techniques. Numerical design techniques are based on sophisticated computational techniques which analyze the stresses and strains through the interstices of a pillar. Empirical techniques are less exact, but have been widely used, particularly for coal mine pillar design, because of their ease of computation. Over the years numerous empirical equations have been proposed to calculate the ultimate strength of coal mine pillars. This paper presents a review of the various equations which are most frequently utilized and examines the fundamental assumptions, limitations and applicability of the design formulae. The review intends to provide the practicing mining engineer with an understanding of the assumptions and mathematical basis of each equation to aid in the selection of the criteria most applicable to his specific design problems. Recommendations are made of the empirical equations that are presently most acceptable for design.

Jan 1, 1983

By B. L. Cusack, N. W. Stump

Selected technological developments applicable to lead and zinc mineral processing and changes in Australian concentration practices made since 1770 are reviewed. Laboratory and pilot plant studies of two new ores have been conducted since 1770. These have resulted in final flowsheet proposals which are described. New production capacity since IT0 has been based on plant expansion or the retreatment of oxidised tailings from plants operating pre-1940ts. Major developments in existing plants have come from the application of computer control to crushing, grinding and flotation and the installation of on-stream analysis systems. Flowsheet configurations have been altered in a number of plants. Selected research topics applicable to lead and zinc processing are also reviewed.

Jan 1, 1977

By F. E Turton

THE town of Rancagua, at the junction of the state and Braden Copper Co. railroads, is located 82 km south of Santiago, the capital of Chile. From Rancagua 70 km to the east, situated in the Andes at an elevation of 7000 ft, is the town of Sewell, the location of a millsite. Two and one half km east of Sewell by underground railroad at an elevation of 7500 to 10,000 ft is the Teniente ore-body. The history of El Teniente dates from the eighteenth century, when according to legend a Spanish lieutenant, or teniente, a fugitive from justice, escaped to the Andes and camped at what afterwards became known as the Mineral El Teniente. This man reputedly discovered a vein of high grade copper ore. The first official records date from 1819, when some exploitation was begun, and continue until 1870. The orebody was large and of relatively low grade and was beyond the capabilities of the small groups attempting to operate it. No effort was made to erect a concentrator until William Braden became interested in the property. In 1901 Mr. Braden promoted the necessary capital for the first practical exploitation of the ore-body. Barton Sewell and E. W. Nash, both of the

Jan 1, 1953