Search Documents

By A. M. Al Taweel, S. M. El Mofty, T. A. Hassan, M. R. Moharam, A. M. Ramadan

The axial mixing characteristics of a pilot-scale flotation column were investigated with the objective of identifying means to mitigate the extent of axial mixing that adversely affects its grade/recovery performance. A wide range of design and operating conditions was investigated and the experimental results, obtained using the dynamic response method, were analyzed using three axial mixing models. The dynamic response of the column can best be described using the axial dispersion model. The results obtained suggest that the value of the axial dispersion coefficient, EL. can be signi6cantly reduced by judicial selection of hydrodynamic conditions and/or the use of column inserts that suppress the onset of hydrodynamic instabilities inherent to the operation of conventional flotation columns. Up to 40% reduction in the value of EL was thus obtained by using spargers that produce more uniform bubble sizes, while up to 30% reductions were obtained by controlling the residual frother concentration.

Jan 1, 1995

By James R. Gage

THE lead deposits of Missouri may be divided into three districts, the southwest, middle, and southeast. As too much time would be required to devote a detailed account to each district, only a description of the modes of occurrence of the lead ores in the southeast district will be given. The lead mining region proper of Southeast Missouri is embraced in an area of about twenty-five miles in width by about one hundred in length. The country embraced in this district is very broken, and traversed by ridges from one hundred to three hundred feet in height, with an occasional knob rising higher. Porphyry forms almost the entire substructure of the region, with here and there outcrops of granite. The crystalline rocks were eroded into ridges and valleys before the deposition of the limestone took place. These porphyries are older than the Silurian limestones, and "belong (according to Pumpelly) to the Archaean (Azoic) formation, of which they may be the youngest member in Missouri. They are the near equivalents, in point of age, to the great iron-bearing rocks of Lake Superior, New Jersey, and Sweden."12/02/2007

Jan 1, 1875

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By Michael G. Nelson

A computer simulation of the automatic control of continuous mining machines has been prepared, similar to previous simulations of longwall mining systems and coal thickness sensors. The simulation allows for programmed variation of the horizon detection method, the azimuthal guidance system, the type and configuration of the miner, varying hardness in the unmined face material (leading to varying error in the machine heading), and the miner's cutting cycle. It simulates control of the miner in three axes. Use of the simulator makes it possible to anticipate problems arising from the complex character of underground mining, which include unpredictable multi-pass coupling and unpredictable variation in geological conditions.

Jan 1, 1993

By Wiltshire PG

The process uses sodium hydroxide and sodium nitrate reagents as in conventional Harris refining plants, selectively removing the arsenic to the caustic phase at an operating temperature of 420-450¦C. A novel feature of the process concept is continuous treatment of loaded caustic slag for recovery of arsenic as a sandy crystal product suitable for further processing to arsenic trioxide. A large pilot plant was constructed and operated over a period of 3 years to develop materials handling techniques and equipment components and to prove the concept. Stable operations were achieved at equivalent capacities of 200 tonne/yr arsenic removal. The process is being considered in plans for expansion of bullion softening capacity at Port Pirie.

Jan 1, 1984

By Ryan Law

Ground energy systems are being installed in increasing numbers in the United Kingdom. This is particularly true in London where planning regulations require larger scale developments to provide at least 10% of their entire energy demands from renewable sources. A common approach has been to use the groundwater from the Chalk aquifer as a source of energy. This paper explains the potential long and short term sustainability problems with groundwater based systems sited in central London (or any other urbanized area). It also outlines an approach to site testing and numerical modelling to ensure that the system functions well throughout its lifetime. This approach is then applied to a project located in central London.

Jan 1, 2008

By Robert Linton

THE PURCHASE of silver by the United States Government under the provisions of the Pittman Act is practically completed. Producers of silver in this country will now have to market their silver in competition with the rest of the world. It therefore becomes of interest to study such data as are available and endeavor to obtain such suggestions as may be afforded therefrom as to the probable future market position of the metal. Conditions influencing the marketing of silver are numerous and complex. It is a commodity entering. into the arts and manufactures, and therefore influenced by the condition of various lines of business which make use of it; it is currency-being used by all countries for subsidiary coins and even as the founda-tion of the system by a very few; and it serves as a frequent basis for speculation. The various factors involved can easily set up so many cross-currents in the flow of the metal that predictions in regard to the market position of silver can never be safely made, although it may be possible to form some idea of prob-able trends over a sufficiently long period. Of course price is determined, as is the case with all commodities, by the inexorable workings of the law of supply and demand.

Jan 6, 1923

By C. M. Frost

Crude shale oil produced by gas combustion retorting of Green River oil shale was hydrocracked over a cobalt molybdate catalyst at operating pressures of 500, 1,000, 1,500, and 3,000 psig, an operating temperature of 8900 F, and a liquid hourly space velocity of 1.0. Hydrogen feed rate was maintained at 6,000 scf/bbl. The volume-percent yields of total liquid product were directly proportional to the operating pressure. Weight-percent conversion and volume-percent yields of gasoline were directly proportional to the log of the operating pressure. Catalyst deposit percentages were inversely proportional to the log of the operating pressure. Nitrogen and sulfur removal rates as well as saturation of the liquid products increased as the operating pressure was increased.

Jan 1, 1973

By D. D. Lambert, E. C. Simmons

Rare earth element (REE) analyses of cumulus plagioclase from the PGE ore zone of the Stillwater Complex indicate that pressure fluctuations in the magma chamber acting on a single magma cannot be responsible for features such as the reappearance of Mg-rich olivine on the liquidus. The data are more consistent with a model involving multiple injection and mixing of geochemically distinct magmas. The PGE-bearing sulfides of the J-M Reef are associated with such a reappearance of olivine, indicating that the unusual location of the ore zone may be related to the addition of new magma, compositionally distinct from magmas that produced cumulates in the Ultra- mafic zone of the complex.

Jan 1, 1984

Silver and gold bearing ore from the Palmarejo mine, located within the Mexican state of Chihuahua, contains a complex mix of electrum, native silver, silver sulfides and silver chlorides. This paper presents a case study that describes the selection, development and engineering of a tailored process plant for the recovery of silver and gold from this ore. Process circuit feasibility study modelling, metallurgical test work and engineering studies are outlined. Options considered to optimise the recovery of the contained silver and gold are compared, based upon cost, operability, recovery and engineering aspects. Concentration by flotation was found to be the preferred primary recovery route. Intensive leaching of the flotation concentrate resulted in solution grades sufficient to allow direct electrowinning to be evaluated against the more traditional Merrill Crowe process. The flotation tailings stream is processed through a separate leaching stage as there is sufficient economic metal extractable from this stream. The processing flow sheet, which is designed to maximise the recovery from both the flotation concentrate and tailings, and to utilise a common metal production facility, is presented.

Jan 1, 2009

By Sergio Demetrio

Based on the current reality of the copper smelters industry, besides the advances that have been and are expected for the next few years, the authors present a futurist vision of the processing of copper concentrates and copper smelters in the years 2000. Outlined new development strategies and ways of improvement in this business, including research, development and management of the works that today posses characteristics of a profitable operation, as well as the changes expected with respect to the entry of new actors and the creation of new products The authors finally bet for small or tailor-made smelters with ad hoc technology for their raw materials and few units to coordinate -devoted to specific concentrates using high technology and low manpower. Considering the in-situ hydrometallurgical route, as well as the pyrometallurgical route in works or conversion facilities that buy or process white metal and produce copper and other metals associated with this such as gold and silver, besides sulfuric acid, plants which should be strategically located in zones with high sulfuric acid price to make this a product which contributes to the profitability of the business.

Jan 1, 1999

To rapidly and dependably locate shorts and opens in mining equipment power cables. Approach: The approximate locations of faults are found using a sound pulse echo, then the faults are exactly located with one of two probes. How It Works: To approximately locate u fault in shielded or unshielded cable, the cable is disconnected from the mine power center, and connected to the sound pulse generator. The generator is also connected to the ground conductor of the cable. When the generator is energized, electrical pulses are transmitted, and each moves along the conductor until it reaches a fault. When a pulse reaches the fault an echo returns to the instrument, either a positive pulse if the fault is an open, or a negative pulse if the fault is a short. See Figure 1. The further along the cable the first fault is from the instrument, the longer it takes for the echo to return. The instrument automatically measures the time and calculates the distance. The distance in feet is shown on an illuminated digital display.

Jan 1, 1976

By Hayashida O, Numata Y

Ultraviolet and infrared spectroscopic analyses and the extended lluckel molecular orbital method were applied to determine the electronic and binding states of 2-mercaptobenzothiazole and the adsorption system of 2-mercaptobenzothiazole on pyrite. 2-mercaptobenzothiazole exists rather in thione form than in thiol forru and the two adsorption peaks in solution were assigned to both 7t--?rt* transitions. 2-mercaptobenzothiazole chemically adsorbs on pyrite mainly due to forming the bond between iron (pyrite) and sulphur (2-mercaptobenzothiazole).

Jan 1, 1993

By A. D. Davis, C. J. Webb, T. V. Durkin

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well-defined drainage in a heavily mined area of the northern Black Hills. The basin contains numerous inactive and abandoned mines, as well as a heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer. Thus, it can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted and two abandoned-mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 2000

Heavy media separation serves to upgrade mill feed and reduce unit operating costs, allowing ores to be mined which could other wise be uneconomic. At the Aberfoyle mine at Rossarden in north-east Tasmania, a simple heavy media operation using a converted Akins screw classifier as a separating vessel, removes barren quartz from mineralised material. At the Cleveland mine at Luina on the west coast of Tasmania a more complex ore mix requires a versatile operation combining hydro-dynamic and static separation equipment to provide an efficient beneficiation circuit. The two operations are briefly described with a background of basic heavy media separ- ation practice.

Jan 1, 1978

Compare the dust control efficiency and bit life of surface coal mine drills using standard water injection and water injection with water separation. Approach A research study was conducted to determine if a water separation technique affects wet suppression dust control. Dust control efficiency and bit life of surface coal mine drills were compared during tests using both standard water injection (wet drill bit cutting) and water injection with water separation (dry drill bit cutting). Background Surface coal mine blast hole drills typically generate a substantial amount of dust during the drilling cycle. One method used to control this dust is the injection of water into the bailing air. This is known as wet suppression.

Jan 1, 1988

By K. A. Natarajan, I. Iwasaki

The effect of poisoning on the behavior of platinum electrodes in redox potential measurements in metallurgical systems was studied in the presence of such inorganic surfactants as cyanide and sulfide and such organic surfactants as dodecylammonium acetate, trimethyldodecylammonium chloride, potassium ethyl xanthate, and potassium diethyl dithiophosphate (Aerofloat®). These chemical species represent, more or less, typical constituents encountered in leaching, flotation, and sewage treatment systems. Triangular wave voltammetry was used as the experimental technique to study the nature of poisoned surfaces. Among the species studied hydrogen sulfide and dodecylamine were found to form a resistant surface film affecting charge transfer. Platinum electrodes appeared to have a weaker tendency to adsorb sulfide species in alkaline pH ranges, while cyanide, xanthate, and dithiophosphate affected the normal electrode behavior differently. Possible methods of reactivation of a poisoned electrode by mechanical cleaning are suggested.

Jan 1, 1974

Two main aspects need to be considered when analysing a potential petroleum development project. Firstly, an estimate of the recoverable reserves must be made, and in many instances, these reserves must serve as collateral to finance development if outside capital is required. Secondly, the likely production profile and cash flow has to be established, and this cash flow then must meet debt service require- ments and in addition generate the required profits. In making these crucial deter- minations, the impact on the project of a wide variety of risks has to be analysed. A computer model, which represents the project in its entirety, is a great aid in determining project viability. Such a model requires imput from geologists, engineers and economists, and interpretation of the model must also be a joint effort. Communications, and inter react ion amongst individuals and disciplines is essential if the best answers are to be obtained

Jan 1, 1983

By Keith Leonard Sutherland

AEROFLOAT 25 is a complex mixture of free cresylic acid with aryl substituted dithiophosphoric acids, sulphides, disulphides, etc. Its complete composition has not been published by the makers or patentees. It is prepared1 by the reaction between phosphorus pentasulphide and carefully selected cresylic acid. We have been informed that this acid contains no phenol and very little cresol, and that it is rich in the higher alkyl phenols, particularly the xylenols. The reaction between a phenol ROH and phosphorus pentasulphide may produce compounds of the following type:2 [ ] Except for the simplest type, the thiophenols (ii), the boiling points of these compounds lie above 300" C. The amounts of the thianthren compounds formed from the five xylenols (if all these are present) will vary according to the position of the substituents. In an attempt to ascertain something of the nature of the reagent, fractional distillation under atmospheric pressure was undertaken. At the outset, hydrogen sulphide was freely evolved, and-particularly below 200°, C.-the fractions had the strong odor characteristic of the

Jan 1, 1939

By L. M. Chan, D. H. Carlson, J. H. Johnson

This paper discusses laboratory evaluation of a tailpipe emissions measurement apparatus (EMA) developed by Michigan Technological University (MTU) under contract to the Bureau of Mines. The apparatus dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, C02, NO and NO2 at known dilution ratios. The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. During the preliminary laboratory evaluation concentrations of DPM, CO and CO2 were measured. The concentrations of CO and CO2 measured by the EMA were usually within ±14 pct of laboratory-measured values for CO and ±20 pct for CO2. EMA DPM concentrations correlated well (r = 0.96) with the laboratory values, but were 29 pct lower on average. The CO and C02 differences were observed to be related to the method of calculating the EMAs' dilution ratio and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminery analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios.

Jan 1, 1991