Search Documents

By N. S. Tanious

Three water-spray ventilation systems were tested to determine their effectiveness in diluting methane at a room and pillar coal mine face. These systems were: the shrouded nozzle, the spray fan, and the conventional nozzle system that is normally supplied with continuous miners. The testing was carried out in two stages. The air-moving capacities of the nozzles were first evaluated in a duct. The duct tests showed that: (1) the volume of air moved by the nozzle is controlled by the type of nozzle, the space around it, and its location relative to the duct wall; (2) the spray fan nozzles or the shrouded nozzles are both capable of moving air quantities up to 6400 cfm (3.02 m3/s); and (3) when the shroud was removed from around the shrouded nozzle, its bare nozzle moved between 9 and 65 percent more air. In the second stage of testing, a full-scale evaluation of the three systems was conducted. The three spray systems were mounted on a continuous miner which was positioned in an aboveground simulated mine entry. The simulated face tests gave the following results: (1) the standard nozzle system, which is mounted on the front end of the miner, is inadequate for diluting methane; (2) under the best testing conditions (lowest methane emission rate, highest primary ventilation airflow, and closest brattice set back), the slight improvement given by either the shrouded system or the spray fan is the same; and (3) under the worst testing conditions (highest methane emission rate, least primary ventilation airflow, and farthest brattice set back), the spray fan gave superior performance.

Jan 1, 1987

By Will H. Coghill

Titanium is a well-known component of bauxite ores, sometimes occurring in sufficient quantity to mace its recovery worth considering. This question has been raised by some of the companies lixiviating bauxite ores. At the East St. Louis plant of the Aluminum Ore Co., a subsidiary of the Aluminum Co. of America, the waste sludge discharged daily contains over 75,000 pounds of Ti02. The sludge is all through 20-mesh, and a large proportion is slime. A supple of the waste was deslimed so that a gravity-concentration test of the "sand" could be made. The Aluminum Ore Co. cooperated in the work and made the chemical determinations In order to anticipate the results of table concentration a series of specific gravity fractions (float-and-sink) was made with heavy liquids. Acetylene tetrabromide was used for a density of 2.95, methylene iodide for 3.33, and thallium formate for 3.78, and the double salt of thallium formate-malonate made the separation at slimed sample appears in Table 1.

Jan 1, 1928

To improve the reliability of the Bureau developed bore-hole gage now widely used to determine the absolute state of stress in rock. Approach Use the knowledge gained by extensive field tests to design a more rugged and reliable Instrument using lighter and stronger materials. How It Works The original gage consisted of a stainless steel cylinder 1-3/8 Inches In diameter and 10-1/2 inches long. The new gage is made from titanium. This lighter material reduces the weight of the gage by 43 percent, which enhances the gage placement and depth of overcoring in vertical up? holes. For added strength, the titanium case and placement end are now threaded to the gage body instead of using screw fasteners. Three pairs of strain gaged transducers are positioned to measure the diametral deformation of a 1-1/2 diameter borehole at 60-degree intervals around the Inner surface of the borehole. Each transducer consists of a beryllium copper cantilever with a strain gage cemented on each side. These transducers are secured Into the gage body by a tapered shank for minimal creep. The transducers opposite each other are wired together to form a 4-arm external bridge circuit. A pair of transducers is referred to as a component. Any deformation of the borehole, which occurs during overcoring, is detected by pistons which translate the motion to the components. Each

Jan 1, 1982

By Roderick Guthrie

Three regimes of bubble formation in liquid metals, in terms of the mechanisms of bubble formation are reviewed. Towards this, bubble formation for a horizontal nozzle submerged in liquid pig iron was re-examined, for which an empirical correlation had been developed, correlating bubble size with gas flow rate, liquid metal surface tension, nozzle outer diameter and the capacitance number of the gas delivery system. Very good agreement between predicted and measured bubble size was obtained for non-wetting, ceramic-liquid metal systems. However, the question of how to create much smaller bubbles than those generally formed in liquid metals according to that work, is critically important. One method could be to create a submerged gas injection system by passing the gas entering the liquid metal through a narrow slot nozzle and make use of Rayleigh-Taylor instabilities. Ralph Harris has provided us with evidence to suggest that a carefully designed slot nozzle might serve as a candidate to create very small bubbles in liquid metals.

Jan 1, 2013

By Otis Hutchins

IT is intended to discuss in this paper the protection appliances used for high-temperature pyrometer installations involving the use of platinum couples and describe some of the characteristics of a new carborundum protection tube. Of all the components that go to make a complete pyrometer installation, the one given the least attention and the one about which there is the least exact information is the outer protection tube. This condition is unfortunate as much, and in some cases even the success of the equipment as a whole, depends on the proper type of protection. In the majority of cases, the installation is allowed to operate without attention until some part of the apparatus breaks clown. The outer tube is the component that usually fails and, more often than not, the failure causes breakage of the porcelain protection and ruin of the couple. This condition should be recognized and studied as it has a very important bearing upon the upkeep cost of pyrometer equipment. The cost of the outer protection tube is small compared with the cost of the platinum couple and procelain protection and it would well repay users of this type of equipment to replace their outer protection tubes at certain definite periods, which experience shows is necessary to prevent destruction of the platinum. Speaking generally, platinum thermocouple equipment is used for measuring temperatures over 2000° F. (1094° C.), and is used extensively for the control of brick and pipe kilns, glass pot furnaces, glass tank furnaces, heat-treating furnaces, open-hearth furnaces, and forge furnaces. A satisfactory protection tube must be sufficiently refractory not to soften at the maximum temperature within the furnace. It must be resistant to cracking clue to temperature changes, should be as nearly gas-tight as possible, and should be made of a material with a high thermal conductivity and great resistance toward erosion by the furnace atmosphere.

Jan 9, 1919

By E. C. Dominguez, H. B. Scharf

The Sparrows Point plant of Bethlehem Steel Co., southeast of Baltimore, is the largest Bethlehem plant, with an annual rated capacity of 6.2 million ingot tons. There is considerable diversity of product, but a high percentage is sheet, tin plate, galvanized sheets, and rod and wire. The large amount of light-weight end product requires a number of pickling installations that necessarily consume large quantities of sulfuric acid. In the coking operations sulfuric acid is also consumed in recovery of ammonia as ammonium sulfate and in treatment of recovered light oil derivatives. Total sulfuric acid consumption in the plant is currently approaching 10,000 tons per month, of which 55 to 60 pct is required for pickling. In 1951 the acute sulfur shortage caused grave concern as to future sulfuric acid supply for the Sparrows Point plant. Raw materials for acid making were already at hand in the form of hydrogen sulfide and pyrites sufficient to produce nearly half the sulfuric acid required at that time. It was also known that the Bethlehem mining activities would produce additional pyrites in the future. Late in 1951 Bethlehem management decided to build a 250-ton sulfuric acid plant at Sparrows Point to utilize these raw materials. The plant was built and put in operation in May 1953. The steel plant has expanded considerably since 1951, and it is now necessary to operate the acid plant far over rated capacity in order to supply plant demand. Production of acid in 1954 amounted to 93,000 tons.

May 1, 1956

By A. F. Nylander, J. H. Jensen

Magnesium, in its combined forms, is the sixth most abundant element and the third most abundant metal in the earth's crust, but it is so reactive that it is never found in nature in the elemental state. As part of the rock-forming minerals like magnesite, dolomite, olivine, and serpentine, it is combined in virtually insoluble forms. As part of soluble minerals like kainite (KC1 MgS04 - 3H20), leonite (K2S0, MgSO, 4H20), langbeinite (K,SO, 2MgS04), and carnallite (KC1 . MgCl? 6H20), it is found in evaporite deposits, generally of marine origin, deep within the earth's crust. Since these minerals are soluble, they are found only in deposits protected from the percolation and leaching action of ground waters by an insoluble and impermeable mantle. Usually this mantle is from several hundred to many thousands of feet thick. Finally, as a solute in marine-like brines, magnesium is common in surface and subterranean waters throughout the world. The oceans, which contain 0.13% Mg, illustrate the inexhaustible nature of the reserve. The recovery of magnesium from the rock-forming minerals, usually by thermal decomposition, and from dilute brines such as sea water by precipitation with lime, are frequent industrial practices. But the recovery of magnesium as magnesium chloride from evaporites or natural brines of concentration greater than sea water has been of little industrial significance for economic and technological reasons. The present US capacity is preponderantly based on the sea-water magnesia process with thermal reduction capacity in second place. No present magnesium capacity is dependent on recovery from the stronger natural brines. But projected capacity, although still weighted in favor of the sea-water magnesia process, is partly based on the recovery of magnesium chloride as a byproduct of potash operations.

Jan 11, 1964

By Robert S. Schecter, Mark P. Walsh, Michael J. Humenick

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within ground-water aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contamination. Since ammonia is one of the constituents of the leach solutions now being field tested, one environmental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laborator.y experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit.

Jan 1, 1979

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By J Watson, C Zhang, I Canbulat, C Wei

Coal burst is defined as a dynamic release of energy within the rock or coal mass in underground coalmines that causes violent rock or coal ejection in the vicinity of mine excavations. It poses one of the highest safety and productivity risks in the mining industry as coal bursts have the potential to cause multiple fatalities. As Australian coalmines go deeper, the likelihood of coal burst increases. Thus, it is critical to assess the ground support requirements in coal burst-prone conditions. A previous study conducted by the authors (Wei et al, 2022) reviewed the support capacities of a wide range of ground support elements in laboratory tests. This study aims to examine the role and effects of the ground support elements and systems for Australian underground coalmines to minimise the damage caused by catastrophic dynamic failures (ie coal and rock burst) and enhance the safety of mine workers.

Nov 29, 2022

By F. H. Willcox

IN Bessemer-steel practice, air is blow, through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and carbon. Toward the end of the blow, when the iron is not protected. from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Bessemer and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast irons is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blowholes lies in part in the presence of dissolved oxide of. iron in the

Jan 2, 1917

By B. F. Koch

COPPER reverberatories develop large amounts of exit gases of a temperature in the neighborhood of 2000°F. The gases are not only of a noxious nature but must usually be disposed of at considerable heights above the yard level by a stack. Handling these gases at the temperature mentioned would require rather expensive construction of conveying flues and stack. Moreover, wasting such amounts of heat is certainly most uneconomical. Numerous investigations have indicated that waste heat boilers of the water-tube type are the most practical and economical means for utilizing that heat although the gases are heavily laden with rock dust and copper-bearing slag, which upon cooling form hard deposits on the surfaces of dampers or heat absorbing elements placed in the gas stream. Avoiding Slag and Dust Deposits Based largely on the experience of the paper industry in burning black liquor, a waste heat boiler design was developed a few years ago, providing not only extensive water-wall surfaces for cooling the gases below the fusing point of the slag but also settling out, as far as possible, the solidified particles of slag by creating low gas velocity. Matter carried in a stream of gases or air has a tendency to maintain its original direction upon a change in the direction of the flow of the conveying medium. Reverberatory waste heat boilers installed at Hurley and Morenci endeavored to utilize that tendency for the elimination of slagging particles at predetermined places and before they would strike the tube banks of the boilers. Both installations were successful in minimizing the slagging of boiler tubes and thereby minimizing the need for hand lancing. However, the low draft carried at the up-take of the reverberatory furnaces resulted in a positive pressure in the upper part of the furnace of the waste heat boilers, causing the emission of gases from lancing doors and making more difficult the already unwelcome work of cleaning the boilers by handlancing. Attempting to correct this nuisance as much as possible, the overall height of the Chuquicamata waste heat boilers has been reduced to the minimum considered necessary to obtain proper water circulation in furnace walls. Moreover, it is attempted to solidify slag and dust particles by providing large amounts of water-cooled surfaces before the gas stream reaches super-heater and convection banks of the boilers. The furnaces have been made as deep as an economical and practical arrangement of headers for water

Jan 1, 1952

By T. M. Chance

THE term "low-sulfur coal," as used in this discussion, is limited to coals containing less, or very little more, than 1 per cent. sulfur. For certain purposes it might be advantageous to include coals that contain as much as 1.25 per cent. sulfur, because such coals have been considered as available for making metallurgic coke of fair grade; but the same reasoning might apply to coals containing as much as 1 ½ per cent. sulfur, if facilities exist for utilizing such coal by admixture with coal containing less sulfur. In Pennsylvania, it is not possible to define the exact geographic limits of the areas in which coals relatively low in sulfur exist, because variations in the percentage of sulfur occur irregularly and often abruptly. It is not uncommon to find areas, more or less circumscribed in extent, in which the coal is relatively high in sulfur although all the surrounding territory contains low-sulfur coal; and, similarly, small areas of low sulfur coal exist in districts where the coal is normally high in sulfur. These generalizations apply, With few exceptions, to the whole area underlaid with bituminous coal in the State of Pennsylvania, and also to each of the individual beds of coal in this state. Pennsylvania is poorly supplied with coals of the low-sulfur class. We find, however, as an offset to this condition, very large areas in which coal ranging from 1 to 2 ½ per cent. sulfur exists in beds of good workable thickness. This coal, by washing, can be reduced in sulfur low enough to make coke of a high grade. While a considerable tonnage of workable low-sulfur coal remains in the Pennsylvania bituminous dis-tricts, it has been necessary to turn to the areas of higher-sulfur coal for the supply of metallurgical coke. This utilization of the higher sulfur areas has been made possible either by washing or by selective mining. Washing.-Fine crushing of the entire feed is not generally necessary to the successful washing of Pennsylvania coals. This is due to the fact that the pyrite is rarely finely and uniformly disseminated throughout

Jan 8, 1919

By D. I. Chalmers

The Brockman rare-metals and rare earth resource is located within volcanic and volcanogenic sediments of the later Proterozoic Halls Creek Group in the East Kimberley region of Western Australia. Exploration including surface trenching, percussion and diamond drilling has defined a major resource of rare-metals and heavy rare earth elements. The host&apos; is a steeply dipping ash-flow tuff, described informally as the Niobium Tuff, enriched in zirconium, hafnium, yttrium, niobium, tantalum, rare earth elements, gallium and beryllium. The mineralization is fine- grained (<20 micrometres) and is the result of alteration and re- mobilization of comparatively simple precursor minerals such as columbite and zircon by fluorine-rich deuteric solutions that were retained in the tuff following eruption. The ultra fine-grained structure of the tuff precludes mineral liberation and separation by physical methods. However, values can be converted to water soluble sulphates by reacting with concentrated sulphuric acid at 250°C. The solution containing aluminium, niobium, tantalum, zirconium, hafnium, yttrium, rare earths and gallium can then be processed to pure products in a sequence of solvent extraction and ion-exchange steps. As a result of these processing techniques, the commercial products obtainable from the resource include mixed rare earth and yttrium concentrates, zirconium-hafnium concentrate, niobium-tantalum concentrate and ceramic grade alumina. Further separation could result in high purity products suitable for ceramic and electronic applications.

Jan 1, 1992

Electron paramagnetic resonance provides a fast method to characterise quartz. Quartz from veins associated with the Cambrian massive sulphide deposits in the Mt Read Volcanics of western Tasmania and from Devonian reefs associated with gold mineralisa- tion at various localities in Tasmania exhibit specific EPR patterns, different from quartz from common veins. The intensity of the EPR spectra of the quartz can be used as a statistical guide to gold mineralisation at Beaconsfield.

Jan 1, 1987

By John P. Dunford

U.S. Bureau of Mines researchers are investigating the ability of mine-wide monitoring systems already in place at many coal operations to provide a direct link between geotechnical instruments and the mine-wide monitoring console on the surface. This paper describes a number of field tests using instruments such as-string potentiometers to measure roof-to-floor closure and bed separation and pressure transducers to monitor pillar loading. The advantages of using existing systems include on-site data collection and analysis, real-time understanding of geological conditions, and long-term data recovery from areas that have become inaccessible to mine personnel. However, because data are generated constantly, large files develop very quickly. In many cases, the data are redundant, such as during times of reduced mining activity or in areas not yet in the vicinity of active mining. To reduce the volume of data, a software program was written that eliminates unnecessary readings and generates a more concise file that can be output to a mine-wide monitoring system, personal computer, or as hard copy.

Jan 1, 1993

By Beeby Thompson

ALTHOUGH the exclusion of foreigners and private owners from participation in the development of the. Russian oil fields prevents first-hand information being obtained, both official and private news indicate a growing appreciation of the value of the country&apos;s oil resources. Notwithstanding the suppression of that initiative and energy which only ambition can adequately stimulate, the industry is progressing and exports of products are assuming an importance that cannot be disregarded as an economic factor in the world&apos;s oil business. The following notes and observations must be regarded mainly as the views of one who has closely followed the fortunes of Russian oil, when considering the changes that have taken place in geological knowledge and oil-field technique, which have so profoundly modified oil-fields methods. Russia is fortunate in having retained the services of. a few scientists and technologists whose devotion to science has superseded their personal inclinations, and to these few men must be attributed the slow, but nevertheless striking, progress that has been made. The productive oil fields of Russia are centered around the Caspian Sea which, with its connected river system, constitutes such an ideal means of internal distribution for products. From the group of oilfields of which the. city of Baku forms a center, oil is pumped to Black-town, a suburb of Baku, where all the refineries are situated. The next important group of oil fields is located in the Terek district near Grosny, where refineries are erected and the products are piped or carried by tank cars to Petrovsk for the internal Russian market, or sent to the Black Sea by rail. A third oil field is spread over the province of Uralsk, north of the Caspian, Sea, the main port of outlet being Gourief, at the mouth of the River Ural. In Trans-Caspia there are two oil-field centers, one near Krasnovodsk on Chelekan Island, and one in Central Asia at Ferghana. The product of the former fields is transported to Baku for treatment, while the output of the Turkestan field is refined and consumed locally, mainly by the railway.

Jan 3, 1925

By R. W. Raymond

ChaRles William HenRy Kirchhoff was born March 28, 1853, at San Francisco, Cal., where his father, Charles Kirchhoff, was at that time consul for his native country, Germany. A few years later, the family moved&apos; to Hoboken, K. J., in which city the son received his preliminary education at the Hoboken Academy, proceeding later to Germany, where he was graduated in 1874 as mining engineer and metallurgist at the Prussian Royal Mining Academy of Clausthal, in the Harz. Upon his return to the United States, he became chemist of the Delaware Lead Refinery at Philadelphia, and retained that position for three years. But in 1877 he began what was to be an almost uninterrupted life-long association with David Williams, the publisher of The Iron Age, of New York, who established in that year, and continued for a brief period, a journal entitled the Metallurgical Review, on the editorial staff of which Mr. Kirchhoff received a place. The enterprise was doubtless an attempt to cover a wide metallurgical field outside of that which properly belonged to The Iron Age. But it was soon abandoned, and Mr. Williams wisely concentrated his energies upon the older journal, which, under his vigorous and skillful management, and the labors of the able editors and correspondents whom he selected, became one of the greatest institutions of its class in the world. From 1878 to 1881, Mr. Kirchhoff was assistant editor of The Iron Age. From 1881 to 1884, he was managing editor of the Engineering and Mining Journal; in 1884 he returned to The Iron Age, to become for five years its associate editor, and in 1889, on the retirement of James C. Bayles, editor-in-chief. This list of dates and employments, without further comment, sufficiently indicates, at least to the eye of an expert, that Mr. Kirchhoff had found his congenial career in trade journalism. His qualifications for this profession were somewhat exceptional. He possessed the scientific training, the knowledge of foreign languages and literatures, and the power of making and keeping friends, which enabled him to get early notice of technical novelties; he had the taste for statistics which made him both industrious and intelligent in their collection and use; and to these traits he added a mastery of the meaning of such accumulated data, and a sane, critical judgment of the situations which they represented, as well as of the sources and the figures themselves, which made his opinion weighty

Jan 1, 1917