Search Documents

By David Bequette, Ray D. Peterson, Cynthia K. Belt

"With a need to cut production costs in the metals industry, cost savings from energy efficiency improvements are critical. Opportunities can be found by reviewing furnace systems and practices so that the melting and holding processes operate at the highest energy efficiency. Many of the changes can be implemented with a minimum of expense or capital investment. This paper will review several low cost methods to optimize energy efficiency on reverberatory melting or holding furnaces. These five methods (furnace utilization, idle procedures, fire rate, controls, furnace pressure) will be explained and information given to implement these changes. Included are several rules-of-thumb and benchmarks for aluminum reverb furnaces.IntroductionEnergy can be a significant portion of the total manufacturing costs for metals and materials manufacturing involving thermal processing such as heat treating, melting, and high temperature processing. Natural gas prices have dramatically varied over the last few years. While no one can foresee the future, prices are expected to increase from the current low prices. More recently, emphasis is being put on the reduction of greenhouse gases with the potential of additional costs to industry.One of the first steps in an energy management program is to measure the energy usage of the process [1]. The results are typically understood in relation to the mass melted in kWh / mT [BTU / lb]. For the purposes of this paper, furnace energy efficiency is calculated over a month or even a year and thus includes hold times. This efficiency is typically different from the values quoted by furnace manufacturers. Those values are for limited short term tests at highutilization.Once you know the performance for your furnaces, these should be compared to industry benchmarks. For aluminum melt furnaces with cold air burner systems, a benchmark value or goal is 1800-2000 BTU/lb [1160-1290 kWh/mt], though some of the best have reached 1600 BTU/lb [1030 kWh/mt]. Furnaces with regenerative burners can attain 1100-1200 BTU/lb [710- 775 kWh/mt]. There are some designs of multi-chamber furnaces or oxygen furnaces that have improved on these numbers, perhaps as low as 950 BTU/lb [615 kWh/mt]. Typically, as the degree of sophistication and energy efficiency of the furnace increases, so does the cost."

Jan 1, 2010

By d&apos, F. Elia

Hot cracking of magnesium (Mg) alloys during welding creates a barrier to enhancing the use of these alloys in automotive applications. As a result, it is imperative to understand the mechanisms responsible for hot cracking of Mg alloy welds in order to develop means of eliminating this problem. In this study, the hot cracking susceptibility of AZ91E and AE42 magnesium alloys were assessed using the moving torch Varestraint test method. Plates of 3 mm thickness were extracted from AZ91E and AE42 ingots and subsequently tested. Quantitative cracking data in terms of maximum crack length (MCL) was used for evaluating the cracking susceptibility. Scanning electron microscopy was carried out. The results suggest that AE42 showed a higher resistance to hot cracking in comparison to the AZ91E alloy. This was attributed to the difference in microstructure between the two alloys. In the fusion zone and HAZ of AE42, the brittle needle-like A1IIRE3 phase was seen to decompose to the more ductile particle-like Al2RE phase, thereby increasing the alloy's resistance to hot cracking. In contrast, SEM fractography revealed that brittle A16Mn and Mg17A112 intermetallic particles segregated to grain boundaries and triggered hot cracking in AZ91E.

Jan 1, 2011

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018

By Y. Champoux, N. Atalla, R. Oddo, C. Lesage

"Percussion drills are the source of the most serious noise problems in mining activities, due to their extremely high noise levels(114-122 dB(A)) and widespread use(Bartholomae and Stein, 1988). Percussion drills will continue to be widely used to drill small diameter holes in hard rock because no other method seems to be economically avail-able to replace them (Boillat et al., 1993).Many studies (Danière, 1991; Hawkes etal., 1977a; Jensen and Visnapuu, 1972;Leblond et al., 1976; Milette, 1989) were con-ducted to determine the major noise sources of percussion drills. The exhaust air of pneumatic drills, the hammer, the bit in contact with the rock and the drill rod have been identified as the major noise sources. A muffer can be used to reduce the exhaust noise and the hammer can be enclosed. The bit noise is considered to be of concern only at the beginning of holes. When all the available methods are used to reduce the noise of a percussion drill, the drill rod vibrations become the dominant noise source (Hawkes and Burks, 1979). However, the noise levels generated by this source remain high and future efforts should concentrate on reducing its radiation.Works by Hawkes and Burks (1979) and Hawkes et al. (1977b) for the U.S. Bureau of Mines provide the most complete description on the noise and vibration of percussion drill rods.The longitudinal and bending waves are the two most important types of elastic waves generated in drill rods. Among these, only the longitudinal waves contribute to the drilling rate. The bending waves are caused by non-centralized impacts, drill rod curvature and non-uniform bit/rock interface. Drill rod noise is generated by Poisson’s ratio expansions and contractions of the rod as the longitudinal waves travel up and down it and by transverse rod motions induced by bending waves. The radiation efficiency is much higher for bending waves than for longitudinal waves. Most of the impact energy is transformed into longitudinal waves, as expected for axial impacts. The evaluation of the relative contribution of longitudinal and bending waves to noise generation poses a very difficult problem for experimental, analytical and numerical approaches. It is, however, an important issue because the relative contribution of these two waves will guide future noise reduction efforts. It seems that very little can be done to reduce the noise radiation of the axial waves without affecting the drilling rate. The main difficulty that analytical and numerical approach-es face, in the evaluation of the relative contribution of the two waves, is that there is no adequate theory for predicting the bending vibrations from the factors that cause them. The experimental approach has, thus, been limited to test fixtures that do not adequately represent the boundary conditions, as well as by measurements obtained under real operating conditions from which it is difficult to establish the relative contribution of the two types of waves. For example, Hawkes and Burks (1979) and Hawkes et al. (1977b) used a test fixture with free-free boundary conditions and made no clear link with measurement under real operating conditions. Rather, they have based their discussion on a simple model. Many authors assume that fexural waves are the main noise source on drill rods. However, measurements have been somewhat contradictory and researchers are still unable to state with certainty that this is indeed the case (Lednik et al., 1988)."

Jan 1, 1997

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda's mine production goal was set at 500,000 tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: Combined the exploration and business development groups Formed teams to search for and respond to opportunity Made our geologists more business minded and our engineers more optimistic Went global Set clear thresholds, farmed out the marginal properties, fast tracked the others Focused reconnaissance exploration where we had a clear competitive advantage Became a "flexible" partner to both juniors and seniors Is it working? A number of successes, near successes, and outright failures are discussed. The main result is a much higher rate of opportunity flux which is essential for success in the mining industry.

Jan 1, 1999

By Zhong Zheng, Xiaoqiang Gao, Zhaojun Xu, Shipeng Huang, Shenglong Jiang

Steel enterprises in China are trending to improve material and energy conversion effect, because they are facing great challenges including energy saving and emission reduction, quality and efficiency improvement. According to the theory of metallurgical process engineering, with the process data in steel manufacturing, some novel indices are designed for quantifying the conversions in different metallurgical unit processes. By analyzing common technologic characteristics in different units, the main manufacturing units are divided into two categories: metallurgical reaction unit and other manufacturing unit. The novel concepts named as “material dissipation rate of unit process”, “material accumulation rate of unit process”, “enthalpy change of unit process” and “energy dissipation rate of unit process” are proposed for describing the effect and dynamic characteristics of the conversions in manufacturing units. Finally, material dissipation rate and energy dissipation rate in unit processes are calculated and analyzed respectively with the real-world process data from a steel plant in China.

Mar 1, 2018

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By B Oostendorp, R van der Merwe, P

In order to assess whether polysaccharide depressants are strongly or weakly and reversibly bound to the surface of talc, a series of experiments was conducted on New York talc in which the floatability of the talc in a microflotation cell was determined. The talc was conditioned in solutions of carboxymethyl cellulose (CMC) or guar gum in 10-2 ionic strength Ca(NO3)2 or Mg(NO3)2. The talc was then washed with four successive aliquots of water, or cation solution, to try to remove the polymer and the flotation response of the talc was assessed. CMCs of different charge (DS) were used to assess the effect of charge on the strength of bonding. The results show that CMC and guar gum could be removed to a large extent from the talc surface by washing with water (the floatability was restored), however very little could be removed from the surface by washing with cation solution. The higher charge CMC was easier to remove from the talc planes in the absence of cations than the lower charge CMC. Thus CMC bonding to talc has been shown to be irreversible or very slowly reversible only if cations are present, implying that cations are necessary to keep the polymer bound to the surface of the planes to effect depression. The presence of ions in solution also had the effect of maintaining surface coverage of the talc by guar gum.

Jan 1, 2005

By O. Engler, J. Friis, S. J. Andersen, C. D. Marioara, Y. Aruga

"This work investigates the early stages of precipitation in Al-Mg-Si alloys using a combination of high angle annular dark field scanning transmission electron microscopy (HAADF-STEM), selected area electron diffraction (SAED) and density functional theory (DFT) calculations. Quenching from a high temperature (solution) treatment leaves an alloy in a high-energy unstable state, with solute and vacancies in supersaturation. Thus, already at room temperature (RT) a large driving force exists for solute atoms to cluster and order on the Al matrix positions. DFT calculations indicate that strain alleviation is important at this stage. We observe larger regions of Mg-dominated L10 ordering together with a Si-dominated ordering of smaller clusters in a particular geometry connected to the Si-network found in all the precipitates. In addition, building blocks of the main hardening phase ?'', stabilized by vacancies, are observed at higher, typical pre-aging temperatures.INTRODUCTION Al-Mg-Si (6xxx) alloys are widely used in industry due to a combination of favorable properties such as strength, ductility, corrosion resistance and lightweight. They undergo a complex production route, usually consisting of the following thermo-mechanical steps: casting, homogenization, extrusion or rolling, solution heat treatment (SHT) and artificial aging (AA). The SHT takes place at temperatures above the solvus line in the phase diagram, usually between 500°C and 570°C, followed by a rapid cooling to RT. This ensures that high amounts of solute atoms, uniformly distributed on the cubic face-centered (FCC) Al lattice, together with a large amount of vacancies, are quenched-in. The material is therefore in a super-saturated and unstable state. During the subsequent AA, at temperatures usually between 150°C and 220°C, the solute atoms diffuse and cluster, forming metastable precipitates with needle/ lath/ rod morphologies having the main growth direction along <100>Al. With a maximum alloy solute level (Mg + Si) of only 2%, these precipitates increase material strength up to three times that of pure Al, and are essential for the final material properties. To understand and make better use of this phenomenon, it is imperative to research the nature of the precipitates (such as their atomic structure), measure their key parameters (number density, size, volume fraction) and connect it to material properties (Marioara, Andersen, Zandbergen & Holmestad, 2005; Marioara et al., 2014). The following precipitation sequence is given for the Al-Mg-Si system:"

Jan 1, 2018

By Chad B. Donovan

There is a strong need in North America and other major steel producing markets where major capital investment in new equipment has been minimal over the past several years to make improvements to existing casting machines. In many cases, very cost effective improvements can be made to existing equipment in order to maximize the efficiency and production of an older designed continuous caster, a classic caster. SMS Group and its predecessor companies have been maintaining continuous casting molds for over forty years. This experience has allowed SMS Group to intimately understand the advantages and disadvantages of each design. The most vital component of the continuous caster is the mold copper design, as it has the most influence over the ability to cast a quality product. Updating to a modern copper design is less complicated than most steel producers think and the benefits are significant. Premium mold coatings such as UniGuard® and NanoGuard® allow casters to guard against exposed copper and wear while producing quality products for record campaign lengths.

Oct 30, 2017

By L. Pretorius, S. Uludağ

This paper explores how to apply system dynamics principles to surface mining problems towards understanding the consequences of mining efficiencies. Some simulation examples related to machine and people performance have been used to demonstrate systems engineering concepts to mining engineers. The simulation tool used is Vensim, which is widely used in industrial engineering applicable to systems thinking, and systems dynamics. The science and mathematics behind the system dynamics as well as benefits and typical challenges are discussed to explore the applicability to mining problems. The benefit of having one less drill is easily quantifiable with the developed model which is one of many other measurable benefits, using the developed model. Some of the benefits of the improved quality of drill holes are not fully quantified as this depends on the mine specific inputs. There are examples of quantifying this in the other industries using system dynamics tools.

Sep 1, 2021

By W. B. Lilienthal, J. C. Melrose

The application of Bingham&apos;s law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham&apos;s law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn&apos; have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham&apos;s law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,&apos; following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham&apos;s integration of Bingham&apos;s law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning&apos;s equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,&apos; the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham&apos;s equation is defined

Jan 1, 1951

By J. R. Schneider

INTRODUCTION Landowners in Texas for many years have freely granted, reserved and leased "oil, gas and other minerals" or interests therein. In recent years we have witnessed much litigation concerning what sub- stances should be included as "other minerals" within the phrase "oil, gas and other minerals," and this question has received the attention of numerous legal scholars. At the South Texas Uranium Seminar held in Corpus Christi, Texas, in September, 1978, Mr. William R. Dodson presented a paper dealing with this very subject and entitled "Uranium - Mineral or Surface? Who Owns It?" In his paper, Mr. Dodson reported on two recent Texas Supreme Court decisions, Acker v. a, 464 S.W.2d 348 (Tex. 1971) and Reed v. Wylie, 554 S.W.2d 169 (Tex. 1977). which held that the particular substance in question in each case is not a mineral within the phrase "oil, gas and other minerals" if substantial quantities of the substance lie so near the surface that production will entail the stripping away and substantial destruction of the surface. Since that time another chapter has been written in the Texas saga of "When is a Mineral not a Mineral?" and it is the intent of this paper to present an update of the Texas law. A review of the early Texas cases so ably covered by Mr. Dodson in his paper will not be repeated, except as is necessary to illustrate the evolution of the legal doc- trine which has been so aptly named "The Surface Destruction Test". BACKGROUND In order to appreciate the genesis of the problem, one must consider that oil and gas production commenced in Texas many years ago, Spindletop came in in 1901. As oil and gas became more valuable, land- owners with considerable frequency sold interest in the oil, gas and mineral estates in their lands, and reserved interest in the oil, gas and mineral estates in their lands when they disposed of their property. Due to the oil and gas background, and perhaps be- cause oil and gas was paramount in the minds of the parties, the traditional language employed in these grants and reservations was "oil, gas and other minerals" or variations thereof. There are literally hundreds of instruments employing this language constituting a link in the chains of title to thous- ands of acres of Texas land. In addition, there are thousands of acres of Texas land held by oil, gas and mineral leases, the primary terms of which have been perpetuated by production, containing similar language in their granting clauses. The severance of the mineral estate from the surface estate results in two separate and distinct estates, each having all of the incidents and attributes of an estate in land. with the surface estate being the serviant estate, and the mineral estate being the dominant estate and having certain easements in the surface estate to explore. produce and remove the minerals. Harris v. Currie. 176 S.W.2d 302, 305 (Tex. 1943). As observed by the court in the Harris case, this is because a grant or reservation of minerals would be wholly worthless if the grantee or reservor co~lld rwt enter upon the land in order to explore for and extract the minerals granted or reserved. Although the Texas law has recognized that an oil and gas lessee has the right to use so much of the surface as is reasonably necessary to produce the minerals. Warren Petroleum Corporation v. Monzingo, 304 S.W.2d 362, 363 (Tex. 1957), recent decisions of the Court have qualified this doctrine. In Getty Oil Company v. Jones. 470 S.W.2d 618 (Tex. 1971). Getty&apos;s pumpine, units were interfering with ones self-propelled sprinkler system utilized for irrigating the premises, and Jones sought to require Getty to install the-pumping units in cellars so that the sprinkler system could pass over them. In an effort to accommodate both the surface estate and the mineral estate, the court held (page 622) "...where there is an existing use by the surface owner which would otherwise be precluded or impaired, and where under the established practices in the industry there are alternatives available to the lessee whereby the minerals can be recovered, the rules of reasonable usage of the surface may require the adoption of an alternative by the lessee". Bearing in mind that the "reasonable use doctrine" grew up in the oil and gas industry involving sub- stances which can be produced by methods that do not destroy or deplete the surface estate, the question presented is whether the Texas courts will extend this doctrine to situations where claimants of "other minerals" seek to produce shallow deposits of iron ore, coal, lignite and uranium by surface mining methods which do destroy or deplete the surface estate? The surface destruction test has answered this question in the negative, at least as to iron. coal and lignite. However, the multitude of mineral estates in Texas which have been created by a grant. reservation or lease of "oil, gas and other minerals" will, doubtlessly, continue to fuel the fires of litigation. EARLY TEXAS DECISIONS In view of the evolution of the Surface Destruc- tion Test, an exhaustive review of the early Texas

Jan 1, 1980

By H. M. Fisher, R. E. Snow, S. C. Sun

SEVERAL constructive and fundamental studies have been made in the analysis of data obtained from experiments carried on with batch ball and rod mills. The operating characteristics of ball milling in small continuous circuits have also been appraised. It is from these analyses that some of the theories of comminution have been developed. Relatively few studies of continuous rod milling have added significantly to the fundamental concepts, because seldom have they yielded sufficiently consistent results. Perhaps they have been too limited in their scope. Careful control of the variables in batch grinding is simple compared with that encountered in a continuous operation. This factor alone has discouraged many investigators. Occasionally results of systematic changes made in industrial rod mill circuits have been published, but usually the data are sketchy and are restricted because of the unwieldiness of the equipment used. The work, in general, has not been comprehensive; nevertheless it has provided empirical relationships that have bridged the gap between postulate and practice so that by proper manipulation of formulae, a mill designer can anticipate mill size and power requirements.14 Although operating variables of a small continuous mill are not so easy to control as with the batch mill, with present day devices, and with careful experimental work, consistent results can be obtained. Nearly four years ago, in the Process Laboratory, Allis-Chalmers Mfg. Co. began a systematic study of the effects of several variables upon the performance of the pilot rod mill. A mill was built in the laboratory to provide the versatility required for the proposed study. It was constructed in sections so that it could be operated, with a few modifications, as a rod mill 30 in. x 8 ft or 30 in. x 4 ft. The discharge end of the shell was flanged so that either an end peripheral discharge or an overflow discharge could be installed. Thus the performance of at least four types of mills could be studied merely by changing the type of discharge or the length of the mill shell. The grinding experiments were designed so that a study could be made of the way in which the mill speed, feed rate, and pulp density influenced the performance of both overflow and end peripheral discharge rod mills. Four sets of experimental data were collected from the four mill arrangements. The mill in each set of experiments was fed at four rates of feed depending on the length of the mill, at four pulp densities, and at five percentages of critical speed. Electrical and mechanical controls were in- stalled to regulate all these independent variables, and auxiliary devices were used to verify the precision of the controls at each point. The dependent variables used to quantify the experiments were the reduction ratio and the hew surface area produced as calculated from sieve analyses. These were incorporated with the energy factor by the calculation of both the new surface produced per unit of energy and the Bond work index.&apos; Rod wear, as a dependent variable, was not studied because of the short period of operation for each run. Exclusive of repeat runs, each set of experiments yielded 80 products, and the total study at least 320 products, all of which were quantified. With the operating information collected, these data presented a bewildering accumulation. Statistical analysis has been invaluable in unraveling the confusion and in presenting a means of establishing the nature and the magnitude of the significant variables. Data presented in this paper are those from the 30 in. x 4 ft end peripheral discharge rod mill, Fig. 1, when limestone was ground at feed rates of 1000, 2000, 4000, and 5000 lb per hr, at pulp densities of 50, 60, 70, and 80 pct solids, and at mill speeds of 50, 60, 70, 80, and 90 pct of the critical speed. These 80 tests have all been run at least twice, and occasionally a third time, to prove that the data obtained were reproducible. The techniques of operation and the methods of quantification of results are described in the following pages and the results analyzed statistically to show the significant variables. The variables are plotted to show the relationships that exist. A massive dolomitic limestone from Waukesha Lime and Stone Co. was used for feed during these experiments because of its availability and its tex-tural uniformity. This limestone analyzed 28.7 pct CaO, 21.0 pct MgO, 6.0 pct SiO2, 0.4 pct A1²O³, and 0.3 pct Fe²O³ and had a loss on ignition of 44.1 pct. It had a rod mill grindability at 14 mesh of 9.6 grams per revolution from which a work index of 13.9 was calculated. The ball mill grindability at

Jan 1, 1955

By J. C. Melrose, W. B. Lilienthal

The application of Bingham&apos;s law to the behavior of drilling fluids in a rotational viscometer permits the expression of viscometric data in terms of plastic viscosity and yield value, the flow properties of a plastic fluid. A commercially available rotational viscometer is described, and when modified to a multispeed type viscometer, is shown to provide a simple and convenient instrument for the measurement of these properties both in the laboratory and in the field. The data obtained are shown to be useful in defining and understanding mud control problems relating to chemical treatment and to the hydro-dynamic behavior of muds. INTRODUCTION The highly complex drilling fluids which are required for deep drilling often give rise to new and unusual mud control problems. Rapid and economic solutions to these problems may require, on the one hand, better understanding of the changes which contaminants and chemical treating agents produce in the colloidal and inert solids of the mud, or, on the other hand, closer control of the hydrodynamic behavior of the mud. The latter objective obviously can be achieved only if a correct rheological analysis of the flow behavior of drilling muds is available and if this is accompanied by the appropriate rheological measurements. The purpose of this paper is to describe such measurements in the field, and to show how the resulting data can be of value in solving difficult mud control problems. It is now generally recognized that Bingham&apos;s law of plastic flow can be utilized in describing the hydrodynamic behavior of drilling fluids in the non-turbulent flow range. Beck, Nuss, and Dunn&apos; have recently applied this law to the flow of mud in small pipes, and Rogers2 has reviewed the rather extensive literature on this subject. So far, however, the use of Bingham&apos;s law has been restricted to the analysis of mud flow in pipes or capillary tubes, and it has not been directly applied to the flow in rotational viscometers. In the work to be reprted, the Reiner-Riwlin3 equation for the flow of a plastic fluid in a rotational viscometer has been utilized to permit the expression of multispeed viscometric data in terms of plastic viscosity and yield value. the two absolute flow properties of a plastic fluid. With regard to the application of these measurements, the calculation of the relationship between pumping rate and pressure drop, both in the drill pipe and annular space, has long been a subject of interest. Beck, Nuss, and Dunn,&apos; following Caldwell and Babbitt: base their calculations for non-turbulent flow on Buckingham&apos;s integration of Bingham&apos;s law for pipe flow and measurements of the plastic viscosity (rigidity in their terminology) and yield value. In the case of turbulent flow, Fanning&apos;s equation is employed, and the pressure drop is relatively insensitive to the flow properties of the mud. Since flow in the drill pipe is likely to be turbulent at usual circulation rates, the plastic flow properties will chiefly influence the pressure drop in the annular space. As pointed out by Beck,&apos; the control of this component of the total pressure drop may be of special importance where lost circulation problems are encountered. Other hydrodynamic problems to which it should be possible to apply measurements of the plastic flow properties include predictions of the velocity distribution in non-turbulent flow and the critical velocity for transition to turbulence. Plastic viscosity and yield value. as abmlute flow propertie.;, will reflect the colloidal or surface-active behavior of the solids present in drilling fluids. Measurements of these properties should therefore find application in developing a better understanding of such behavior and in characterizing the type and condition of these solids. Garrison and ten Brink have utilized multispeed viscometric data in this manner. although their measurements were not expressed in terms of the absolute flow properties. In connection with the application of these measurements, it should be recognized that the presently used one-point viscosity measurements are relative in nature. The API Stormer 600-rpm measurement, for example. is a function of both plastic viscosity and yield value, as well as mud weight, and will often be misleading when its application to mud control problems is attempted. NOMENCLATURE, UNITS, AND DEFINITIONS In Fig. 1 an idealized plot is given of the flow variables involved in any viscometric measurement. It is seen that the flow behavior of plastic fluids is characterized by two constants — plastic viscosity, µp, and yield value, F. Other workers hate used the term rigidity for plastic viscosity or the term mobility for its reciprocal. The term plastic viscosity, however, emphasizes the close relation this property bears to the viscosity of a true fluid and is expressed in the familiar viscosity units of centipoises. The yield value is expressed in lbs/100 sq ft, the units adopted for gel strength measurements with the APT shearometer. Definitions of these properties based on rheological or macrc)scopic flow considerations follow from Fig. 1. The plastic viscosity of a substance obeying Bingham&apos;s equation is defined

Jan 1, 1951

The copper concentrate market is becoming increasingly unstable. In the early 1990s large concentrate stocks were built up and the glut was cleared only after treatment charges rose so sharply that &apos;non-traditional&apos; custom smelter capacity, such as in Kazakhstan, could be employed, By 1994 the market had shifted and Western smelters were unable to secure enough concentrates to operate full out. The reason for these sharp swings in the market balance is that virtllally all the recent mine development has been non-integrated. With different companies developing new mine . and smelter capacity, it is inevitable that the pace of expansion in the two sectors will not be coordinated. For many years the Japanese smelters were the major buyers from the new mm-integrated mines. However, Japanese smelter capacity is unlikely to increase appreciably in the future and this stabilizing influence will be very difficult to replace. This paper will examine the likely concentrate/smelter balance over the next five years and will forecast the likely direction of? treatment charges. It will also touch on the critical variables in assessing the viability of new greenfield custom smelter capacity, such as proximity to concentrate sources, by-product sulfuric acid prices and, most importantly, tariff protection.

Jan 1, 1995

By Chas. H. Behre

MINING geology, both theoretical and practical, continued to make noteworthy progress during 1938. Mining companies generally, stimulated especially by the improvement in economic conditions during the latter part of the year, extended their workings and developed new ore bodies. Federal and state surveys expanded their search for favorable localities and actual ore bodies, with corresponding enlargement of regional knowledge. Theoretical investigations covered geochemistry of ore deposition, structural control of mineralization, and mineralogy of the ores (chiefly aided by the microscope). More geochemical work is greatly needed: ore searching is still too purely empirical, based on features that have been recognized else- where. Thus, clearer understanding of the conditions essential to transportation of metal salts is needed. Jean Verhogen has suggested that solubilities

Jan 1, 1939

By C. L. Wilsey, K. M. Oakes, W. J. Reich, M. J. Protani

The time frame required to complete the National Environmental Policy Act (NEPA) process for a new mine or the expansion of an existing mine can range from nine to 24 months, or even longer. The time frame will vary depending on whether an environmental assessment (EA) or an environmental impact statement (EIS) will be completed Completing properly designed baseline studies to collect natural resource data to support the EA or EIS prior to the start of the NEPA process can shorten this time frame. In this paper, a two-year natural resource baseline study by Homestake Mining for the Ruby Hill Mine, Eureka County, NV, is used as a case study to describe how a properly designed and executed natural resource baseline study streamlined the NEPA process.

Jan 1, 2003

By L Yao, J Li, C Sammut, B Li

The underground mine environment is inherently complex and hazardous, which necessitates ensuring mining workers’ safety. With the fast development of AI techniques, human activity recognition has become a crucial task to enhance daily life, especially in such challenging settings. This enables automatic monitoring and detection of the mine workers’ activities and operations on a large scale, which leads to better support of workers’ safety and welfare. Existing traditional uni-modal approaches, which use data of one single modality, suffer from low data quality and noise, so they struggle to generalise effectively in such extreme conditions (Li et al, 2022). As underground mines have extreme and complicated environments, such as dust, low light, signal interference, and rugged terrain, uni-modal approaches could not resolve such obstacles and are not suitable for real-world deployment. Multi-modal human activity recognition approaches could use data from multi-modal sources, thus capturing complementary information and producing robust and effective performance in recognising and monitoring mining activities. In this case, designing suitable multi-sensor hardware and AI activity recognition models has become a pivotal task. Producing efficient multi-modal approaches for edge deployment is another problem worth exploring.

Sep 1, 2024