Search Documents

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By B. Aydin, A. S. Aloglu, S. Kahraman, E. Saygin

"The coal strength parameter is used in operations such as the selection and design of mechanical excavators and coal crushing/grinding equipment. However, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason a method for the indirect determination of coal strength from easy tests would be useful. In this study, the predictability of coal strength from the needle penetration test was investigated. This is a very easy and practical test method. Point load and needle penetration index (NPI) tests were carried out on coal specimens from Çayirhan coalfield in Turkey. The point load indexes were converted to the uniaxial compressive strength (UCS) values by using the general conversion factor. The UCS and NPI values were evaluated using regression analysis. A strong linear relationship was found between the two parameters. The conversion factor for the UCS-NPI ratio is 0.35 for the tested coal samples. It is concluded that the UCS of coal can be predicted from the NPI.IntroductionKnowledge of coal strength is important for the selection and design of mechanical excavators and coal crushing and grinding equipment. Uniaxial compressive strength of coal is used in designing pillar dimensions in room and pillar mining. Coals always contain bedding planes and cleats; they are also brittle and fragile. Therefore, coring or cutting prismatic specimens from coal for the standard strength tests is difficult, and sometimes not possible. For this reason, a method for the estimation of coal strength from easy tests would be useful.The needle penetration test is a nondestructive index test that is applicable both in the field and the laboratory and does not require any special sample preparation. The test has been used for the estimation of physical and mechanical properties of weak or soft rocks (Okada et al., 1985; Yamaguchi et al., 1997; Takahashi, Noto, and Yokokawa, 1988; Uchida et al., 2004; Aydan et al., 2006; Aydan, Watanabe, and Tokashiki, 2008; Aydan, 2012; Erguler and Ulusay, 2007; Park, Obara, and Kan, 2011; Ulusay and Erguler, 2012; Aydan and Ulusay, 2013; Aydan. Sato, and Yagi, 2014). This study investigates the predictability of coal strength from the needle penetration test."

Jan 1, 2017

By Felipe da Silva Siqueira, Weslley Luiz da Silva Assis, Camila dos Santos Pinto, André Luiz Moraes Alves, Guilherme Dias da Fonseca, Paulo Rangel Rios

Neste trabalho estudou-se o comportamento cinético das transformações de fases por nucleação e crescimento nas interfaces (faces, arestas e vértices), das matrizes poliedricas de Kelvin, Voronoi e de Monte Carlo, através da simulação computacional. Com o objetivo principal de comparar os resultados obtidos das simulações com os modelos analíticos de Johnson e Mehl, Kolmogorov e Avrami (JMAK), e de John W. Cahn. As matrizes foram geradas por modelos estocásticos e através do método de crescimento do Cone Causal. Em engenharia o entendimento do comportamento das transformações de fases por nucleação e crescimento são importantes para prever os possíveis locais de nucleação, assim como no entendimento do comportamento dos constituintes presentes do diagrama ferro carbono, na decomposição da austenita, no processo de recristalização, entre outros. Desta forma, o modelamento computacional foi utilizado para o estudo das transformações de fases por nucleação e crescimento, obtendo como resultados a fração volumétrica, o caminho microestrutural e a contiguidade, ambos resultados foram importantes para a caracterização microestrutural e para descrever a distribuição dos núcleos no espaço. Com os resultados obtidos observou-se que se os núcleos estão bem distribuídos nas interfaces o impingement será mais fraco, levando as simulações de Voronoi e de Kelvin a corroborarem com o modelo analítico de JMAK, já o Modelo de Monte Carlo, não apresentou o mesmo comportamento, ou seja, ficou evidenciado que nem sempre a aleatoriedade vai ser válida para todos os casos. Foi constatado também que se aumenta consideravelmente a quantidade de núcleos, a distribuição perde a característica de aleatoriedade e passa a se comportar como clusters, corroborando com o modelo analítico de Cahn.

Nov 10, 2019

By P. Saunier, S. Fourmont, R. Stafford, A. Jung, J. Mlynarek

The safe and economical storage of tailings generated by modern day mining operations is possibly the single largest challenge faced by miners today. By nature, tailings are a waste product that have little to no economic value. Yet, their physical and chemical contents can pose incredible environmental hazards if not stored correctly. The variety of factors that are met when designing Tailing Storage Facilities (TSFs), means that in most cases, a low-cost solution is sought to accomplish storage, meet environmental regulations, and adhere to industry best practices. TSFs can be large dam face structures or smaller structures like retention/evaporation lined ponds. Water management is potentially the single largest factor that miners and designers must contend with when constructing a TSF. Water is a necessary component in the process of extracting ore but can be difficult and expensive to remove once it is mixed with solid tailings particles. As a result, the most common disposal of these water containing tailings, called a slurry, is to simply discharge into an embanked TSF (Vick, 1990). These structures, just like any other water retaining dam, can breach releasing contents downstream. Despite modern advancements in TSF design, there have been numerous dam failures that have resulted in tragic loss of life and ecological devastation. Most notably in the last decade, the Brumadinho and Mariana Dam disasters in Brazil killed 278 people in downstream communities when TSF dams failed in 2019 and 2015, respectively (Rotta at el., 2020). Similarly, in 2014, the Mount Polley tailings spill in British Columbia was the second largest tailings spill on record and caused extensive damage to adjacent watershed ecosystems when the TSF embankment was breached (Byrne at el., 2018). While there were indeed numerous unique and underlying factors present in each of these structural failures, a shared element in the devastation was the large-scale release of unstable liquefied tailings

Mar 2, 2022

The primary goal of a maintenance information system should be to aid the maintenance department in providing the required equipment or plant availability at the lowest possible cost. To achieve this goal, the system must provide information in support of the following objectives: (1) establishing the best fleet, equipment, and component configuration; (2) establishing the best maintenance program; (3) executing the defined maintenance program efficiently; and (4) monitoring equipment availability. These objectives can be satisfied with five groups of reports. Each of these groups should provide regular, periodic reports to aid in planning and monitoring trends, exception reports to identify problems, and on-request reports to provide analytical capabilities.

Jan 1, 1979

By John A. Ruppert, John E. Conley

Shortages of cinders, largely resulting from industrial plants converting to fuel-oil, together with an enhanced building activity, have seriously affected the cinder block and lightweight concrete manufacturers. In the search for other sources of lightweight aggregate, various clays, shales, slates and natural occurring lightweight rocks such as pumice, scoria, volcanic ash and the like have received special attention. Methods and equipment for producing suitable lightweight aggregates have been considered. In addition to an expanded use of the rotary kiln, the traveling-grate and continuous-sintering machines are being installed in many localities.

Jan 4, 1950

By A J. Moore

The Australian Coal Association Research Program (ACARP) funded project, No C14057, entitled æEffect of Blasting on InfrastructureÆ, has been carried out with the objectives of providing methodologies for the assessment of the strength of infrastructure types and the establishment of responsible and realistic limits. Personnel from Melbourne, Newcastle and Swinburne Universities and Terrock Consulting Engineers conducted the project. Infrastructure types including: conveyors; power transmission towers; wooden power poles; electrical substations; pipelines, bridges; public access roads and underground workings have been investigated by both field studies and structural analysis. Railways, underground telecom cables, dams and industrial buildings have been reviewed using general structural analysis. This paper has been prepared for the mining industry to provide a progress report on the project.

Jan 1, 2007

[WILLIAM LITTLEJOHN President Castle Gate, Utah BENEDICT SHUBART Secretary-Treasurer 521 Boston Bldg., Denver, Colo. .JAMES DALRYMPLE Vice-President for Colorado State Office Bldg., Denver, Colo. HORACE MOSES Vice-President for New Mexico Gamerco, New Mexico .J. B. FORRESTER Vice-President for Utah Hiawatha, Utah P. H. BURNELL Vice-President for Wyoming First National Bank Bldg., Ogden, Utah EXECUTIVE BOARD COLORADO: J. B. DICK Walsenburg R. A. McALLISTER Trinidad NEW MEXICO: W. W. RISDON Albuquerque J. B. MORROW Dawson UTAH: CHAS. LEGER Rolapp R. R. KIRKPATRICK Sunnyside -WYOMING: F. L. McCARTY Rock Springs J. C. RAE Gebo]

Jan 1, 1924

By K H. Esbensen

The critical role of representative sampling is featured and illustrated by selected examples from the geosciences and beyond. As there already are many demonstrations of the potential (and potentially large) economic consequences of ignoring proper standards with respect to representativity, eg for mining and minerals processing companies, which æstand to lose millions of dollars by failing to optimise exploitation of their mineral resourcesÆ, such need no further iteration here.This keynote lecture, rather, takes a point of departure from the opposite perspective: what is to be gained by a scrupulous stand for representativity? Honesty, reputation, credibility, market advantage - is what!CITATION:Esbensen, K H, 2012. The critical role of representative sampling, in Proceedings Sampling 2012 , pp 9-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By A. F. Daily

Free World consumption of diamonds of all types closely follows the fluctuations of the business cycles in the large industrialized countries, particularly the U.S. Sustained purchasing by this country for stockpiling purposes has been a major factor in Free World demand for crushing bort and industrial diamonds, and it has been for this reason that investments in larger plants have been made by all major diamond mining companies during the past few years. For the purposes of this study, the diamonds produced in the Congo and elsewhere in the Free World are divided into three types:

Jan 5, 1961

By Bruce H. Van Brunt, Danny L. Taylor

Estimation of local recovered tonnage and its grade above a cutoff is of paramount importance during the exploration and development stages of any mineral deposit. The spatial dis- tribution of grades as well as the cumulative distribution must be defined. In this paper, Probability Kriging, an estimator based upon rank order statistics and the estimation of the distribution of point grades within a panel, is applied to the Manhattan gold deposit. Mapping the conditional probabilities that estimated panel grades exceed a cutoff is useful to the understanding of the distribution of mineralization in a structurally controlled gold deposit.

Jan 1, 1989

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By William E. Ford, Edward Salisbury Dana

1. Normal Class (28) Gypsum Type 2. Hemimorphic Class (29) Tartaric Acid Type 3. Clinohedral Class (30) Clinohedrite Type Mathematical Relations of the Monoclinic System Crystallographic Axes. - The monoetinic system includes all the forms which are referred to three unequal axes, having one of their axial inclinations oblique. The axes are designated as follows : the inclined or clino-axis is a; the ortho-axis is b, the vertical axis is c. The acute angle between the axes a and c is represented by the letter 0; the angles between a and b and b and c are right angles. See Fig. 331.

Jan 1, 1922

By P. Ritsopoulos, A. J. Dentsoras

The objective of this paper is the development of a reliable simulation model for the operation and production capacity of an aggregates quarry. Based on this model, a computer program is introduced that provides the final production outputs according to the defined material gradation and machinery characteristics. The program takes into consideration all operational parameters that may be introduced by the user through the whole machinery network. As a result, all production parameters are properly updated. The structured simulation program can help detect production inefficiencies that result from design ineffectiveness. Additionally, the program can be used for the generation of alternative scenarios for future modifications of a plant's configuration. Finally, a designer can use it as a tool for obtaining optimum solutions concerning newly designed quarries. As a case study, a quarry operating at Heraklion, Crete, was examined. The application of the program to the plant produced a complete image of the quarry's input/output characteristics, along with some suggestions for improvements on certain production processes.

Jan 1, 1998

By Donald C. Myntti

Modern open-pit mining can be described as a capital-, labor-and energy-intensive, large-scale, mechanized, and highly repetitive bulk material preparation and handling operation, with emphasis on the word "mechanized." In hard rock, this generally means shovels loading blasted materials into haulage units for transport to processing plants, stockpiles, or waste dumps. Mine management deals with several primary concerns on a daily basis; e.g.: Will any serious accidents and labor problems occur today, and will the tonnage targets be met considering the physical condition of the equipment? The latter subject will be discussed from a maintenance perspective. A successful, progressive heavy equipment maintenance program that protects company assets involves many elements. They include: •Proper equipment selection and procurement •Well-trained and motivated workforce •Good shop facilities •Preventive maintenance (PM) program •Warehouse support •Operations-maintenance department cooperation •Meaningful paperwork

Jan 3, 1978

The Nelson province was chosen as the prime area for rhenium sampling, based on its mineral associations. Sample preparation involved benefication by grinding and flotation. A modification of published procedures for rhenium analysis was developed and the results compared with those obtained for molybdenum on the same samples using atomic absorption spectroscopy. The results of the analysis for both metals is discussed and the relationships between rhenium and the molybdenum mineralisation of this region is commented on. A metallogenic province is defined for molybdenum and rhenium and the tectonic setting for this is discussed. Some consideration has been given to rhenium possibilities in Fiordland and the Coromandel Range.

Jan 1, 1980

By R. C. Wilmoth, R. D. Hill, R. B. Scott

A cost breakdown is given for reclamation and mine drainage abatement conducted by the Federal Water Quality Administration's demonstration project near Elkins, W. Va. Costs for construction of control measures have been developed and include backfilling strip mines, sealing subsidence areas, reconstructing stream channels, and installing mine seals to prevent the entrance of water and air.

Jan 1, 1973

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977