Search Documents

By Leslie G. McMillion

A field project to develop and demonstrate a method for alleviating problems of highly mineralized ground water where they occur as isolated zones or pockets in fresh-water aquifers is being conducted in the Ogallala aquifer of eastern New Mexico by the Robert S. Kerr Water Research Center. Removal of contaminated water is by a large-capacity well and the pumped poor-quality water is used locally for secondary recovery of oil. Benefits of the operation are threefold in that the aquifer is being reclaimed for future fresh-water production, contaminated water is being used beneficially, and fresh water which otherwise would have been used for waterflooding is available for other purposes. Ground-water quality in the site has improved markedly after two years of operation. Use of water in the arid and semiarid Southwest has grown so rapidly that demands in many localities far exceed available supplies. In the High Plains region of New Mexico, Oklahoma, and Texas, the only large sources of water are underground reservoirs, being depleted at an alarming rate. In some parts of this region, the aquifers contain pockets of highly mineralized waters; and the mineralized waters in some of them have started spreading in response to the drawdown effects of pumping wells. The aquifers of this region are primarily composed of sand and gravel beds; any cleanup by natural processes will require many tens or even hundreds of years. Most of these pockets of highly mineralized water were caused by oil-field brines seeping downward from earthen disposal pits. Thousands of these pits were in use in the region until only a few years ago when they were prohibited by the oil regulatory agencies of the respective states. The resulting areas of poor quality water are serious enough to warrant much corrective attention. Correction will involve one or more of three approaches: 1) Restrict the pumping of fresh water in the zones where the drawdown of the pumping well will significantly influence the movement of the contaminant. 2) Remove the highly mineralized water entirely from the affected area. 3) Develop and pump the poor-quality water in such a manner that its movement is held in check, even though only a part of the contaminant is actually removed. The principal hurdle to overcome in applying methods 2 or 3 is financing of the operations, since there are very

Jan 1, 1972

By Herbert Hughes

The trend in modern building construction is definitely toward the use of weight-reducing materials. The basic advantage of lighter structural weight is obvious; reduction of dead load with retention of equivalent strength affords the possibility of increasing the live load, or if this is not desirable or necessary it makes feasible a reduction in size of structural steel members and corresponding savings in other phases of construction. Among the weight-reducing materials and practices rapidly gaining favor are the use of light-weight patented insulating board to replace back-up tile or units, particularly in home construction; introduction of aluminum alloys to replace steel for many purposes; manufacture of porous brick, the use of which materially reduces the weight of masonry walls and partitions; and the use of self-rising vesicular concrete, dia-tomite and sawdust tile, porous gypsum, or gypsum tile for nonload-bear-ing partitions and walls. Even building accessories are being designed to save weight and space; one of the most striking examples of this is improved radiator construction. Concrete technique is keeping pace with the rest of the industry. Burned shale aggregates now available in many sections of the country will make concrete weighing only 100 Ib. per cubic foot, saving roughly 35 per cent. in weight and sacrificing none of the strength of a rock-sand mix. It may be more expensive, but actual experience has shown that the saving in dead load will effect a reduction in structural steel which in many instances will more than offset the increased cost of the aggregate. The vesicular nature of most light-weight aggregates gives the concrete especially good insulating, fireproofing and soundproofing properties; yet absorption is compara.tively low. Strangely enough, however, the increased use of light-weight aggregates appears to have augmented the demand for ordinary aggregates in concrete construction rather than to have decreased it. Light-weight aggregates have widened the field for concrete structures and, since the producers do not attempt to recommend the use of their material except where weight or other special properties are important factors, impetus has been given to sales of other aggregates.

Jan 1, 1931

By John Palomino Melgarejo, Jose Soto

Compañía de minas Buenaventura en concordancia con su política ambiental y en cumplimiento con sus normas legales vigentes ha venido cumpliendo la ejecución del plan de cierre de la Unidad Esperanza; la estabilización Física, geoquímica e Hidrológica fueron la base de los trabajos operativos, para ello se realizó una revisión minuciosa de las especificaciones técnicas de ingeniería de detalle para el cierre de bocaminas con efluentes y se ha propuesto nuevas actividades de ingeniería para la correcta ejecución de los trabajos programados. Así mismo se complementó nuevos productos los cuales dan un valor agregado a los trabajos de impermeabilización de bocaminas asegurando su funcionalidad al largo del tiempo.

Sep 1, 2017

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

Reduce longwall shearer operators' dust exposures by more effectively suppressing the dust generated by the upwind cutting drum. Approach Direct more of the shearer water supply to the upwind drum, thus reducing the shearer operator's exposure to respirable dust while making more efficient use of water. How Proportioning Permits More Efficient Use of Water On most longwall mining operations, the cutting action of the shearer drums is the primary source of dust. Al-though the amount of dust generated is directly related to the amount of coal and rock cut by the drum, the exposure or the shearer operators to dust depends more on their work position relative to the upwind drum. When cutting with the airflow, the upwind drum, cutting bottom coal and floor rock, is the primary generator of dust reaching the operators. The lead drum is downwind of both shearer operators and is thus of less concern. (See diagram). When cutting against the airflow, the lead drum is upwind-taking a full cut, including roof rock-and both shearer operators may be exposed to very high levels of respirable dust. Currently, water sprays mounted on the cutting drum provide the most effective method of controlling dust from longwall shearer drums, and all longwall mining operations use some type of bit flushing or cavity filling water spray system on the cutting drums. Bureau surveys of longwall operations, conducted as part of its research program to reduce respirable dust, have indicated that six longwalls with better than average compliance records use higher than normal water flowrates to the cutting drums. The average water flow to the shearers at these six operations was approximately 60 gpm-about 50 percent more water than is normally supplied to double-drum longwall shearers.

Jan 1, 1982

By Leopoldo Gutierrez, Sergio Castro, Lina M. Uribe, Janusz S. Laskowski

"The effect of sulfite and metabisulfite ions on the amyl xanthate flotation of copper-activated pyrite, in distilled water and seawater, has been studied by micro-flotation tests and redox potential measurements. The activation of pyrite was carried out varying copper ions concentration. It was found that in the presence of copper ions in solution, sulfite and metabisulfite are able to depress copper-activated pyrite at neutral or slightly acid pH. After the addition of sulfite or metabisulfite ions the resulting pH is more acidic with metabisulfite ions. A significant increase of the redox potential of the solution was observed as copper ions concentration increased. Then, the initial reducing conditions brought about by sulfite and metabisulfite ions, change abruptly to oxidizing conditions in the presence of copper ions. Under these oxidizing conditions, the metabisulfite showed to be an effective depressant for pyrite mainly in seawater. However, sulfite was a pyrite depressant in both distilled water and seawater. Based on these results, the pyrite depression by sulfoxy-depressants during the flotation of Cu/Mo ores in distilled water and seawater is discussed.INTRODUCTIONDepression of pyrite by sulfoxy-depressants (sulfite and metabisulfite) in the presence of copper ions is an important issue. This is particularly true when pyrite depression in the flotation of Cu/Mo sulfide ores is carried out in seawater. The use of lime in seawater must be avoided because the formation of magnesium hydroxy-complexes and precipitating magnesium hydroxide strongly depresses molybdenite flotation (Castro et al., 2014). In order to solve this problem, one large plant in Chile uses sodium metabisulfite (MBS) instead of lime to depress pyrite in seawater. In plant practice, this also improves molybdenite flotation since with the use of MBS the pyrite depression is carried out at pH 6-7, instead the pH 11-12 usually employed with lime.From a general point of view, pyrite exhibits some natural floatability over acidic pH ranges and may be partially floated without thiol collectors (a coating of sulfur/polysulfides has been claimed). Therefore, pyrite flotation with xanthates is usually high in the acidic pH region, but decreases greatly at alkaline pH (Leppinen, 1990; Fornasiero and Ralston, 1992; Zhang et al., 1997)."

Jan 1, 2016

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By A. W. Farenwald

Fine grinding cannot be accomplished in machines in which the component parts move in definite and restricted paths with respect to each other. Such machines are crushers. A "grinding mill" may be defined as any machine in which the crushing elements are free to make direct contact with each other but are kept from doing so by the sand to be crushed. Such a machine must possess the ability to give numerous contacts per unit of time. Upon consideration, one will see that this definition nearly includes the old Chilean and Huntington mills, the "rolls" and the stamp mill. It definitely includes all forms of ball, pebble and rod mills. The ideal (perfeet) grinding mill may be defined as one in which the crushing elements are identical in shape and substance and possess perfect freedom of motion with respect to one another. Of the mills mentioned, only the ball and pebble mills come under this definition of the ideal mill. Even the rod mill fails to get a place under this definition of the perfect mill. Modern Fine-grinding Mill In current practice fine grinding is performed in rotating cylinders1 partially loaded with hard objects, the agitation of which accomplishes the crushing or grinding of the rock or ore. The hard objects called "grinding media" nearly always are steel or some other alloy of iron. Hard rock (flint pebbles) have been and still are used to a limited extent. When steel is used as the grinding substance, the form is the sphere or "ball." The combination of rotating cylinder and steel-ball grinding media is termed "ball mill." Shapes other than the sphere have been tried. Cylindrical grinding media also have been and are now used in grinding mills. When cylindrical media are used the mill is termed "rod mill." Mechanical Elements of Grinding Mills The mechanical elements of a grinding mill arc: (1) the rotating element, (2) the grinding media, (3) the rotating means.

Jan 1, 1935

By Davey P. T, Tsambourakis G

Mineralogical analysis of supergene sulphide ore recovered from areas close to the underground workings at the abandoned Mutooroo (South Australia) mine shows that the original sulphide minerals have undergone substantial alteration. The cause of this alteration is believed to be contact with the highly saline, acidic mine water. The copper is now present as a sulphide that can best be described as a copper- and iron-delicient chalcopyrite, CuxFeyS2, where in most cases x < y. The values of x and y vary from point-to-point within each grain.Leach tests under a variety of conditions show that dissolution of the copper from the supergene sulphide ore can be readily achieved, particularly when compared with the behaviour of Mt Isa chalcopyrite concentrate. For the supergene sulphide ore, an increase in the acidity and the iron(lll) concentration of the leachant re ults in an increase in the rate of copper dissolution.The results are briefly discussed in terms of the experimental in-situ leaching operation at Mutooroo, South Australia.

Jan 1, 1986

By C. R. Hayward, H. O. Hofman

The aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation. The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment, that the present paper deals. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization; by casting a thermal balance to find the distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a summary of several tests will give the best method of operating. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jan 1, 1910

By R. W. Raymond

THE question, what is the best proportion among weight, fall, and speed of stamps, is one which has not yet received thorough and systematic examination. In considering the economical application of stamping machinery, we meet, at the beginning, with serious difficulties in obtaining accurate data for comparison. The weight and fall of stamps vary as the shoes and dies wear out; and this may lead to a change of speed also. Moreover, defects in engines, boilers, or machinery for the transmission of power, may occasion serious losses, which cannot fairly be charged to the arrangements of the stamps proper. Again, the capacity of stamp-mills is directly dependent, in some degree, upon the nature and extent of discharge, fineness of screens, and other peculiarities of the battery. Finally, the hardness and tenacity of the rock crushed varies so much that comparisons between different localities cannot be implicitly trusted. The safest experiments are those made in the same mill, by changing first one and then another condition of working; but this is seldom possible for such conditions as weight and lift of stamps, and only within narrow limits for their speed. We may eliminate questions of friction, transmission, and generation of power, in the case of stamps, by measuring the power actually developed by their fall. Thus, the weight, multiplied into the fall in feet, and the number of drops per minute, gives us exactly the number of foot-pounds exerted by each stamp. Dividing by 33,000, the number of foot-pounds per minute in one-horse power, we have the horse-power per stamp, from which the effective power of the whole mill may be obtained. Dividing the amount of rock crushed daily by the effective horse-power, gives us the daily amount per horse-power; and this is the best measure that can be obtained for the effectiveness of the stamps. A complete discussion of the subject would require us to determine the exact influence of the discharge, etc., and the exact resistance offered by different classes of rocks, for both of which points the data are wanting. Professor J. D. Hague, in the third volume of the United States Geological Exploration of the Fortieth Parallel, gives a valuable

Jan 1, 1873

By R. E. Hathaway

INTRODUCTION For a number of reasons, the mineral processing industry has been slow to adopt significant automation of its processes. Most ore grinding operations can be operated manually so the pressure for automation to run the process has not been there. Furthermore, many plants had proven over years of operation that manual operation would produce a profit, so why automate? Until recently, the instrumentation necessary for automation of the grinding process was not available. All this has now changed, however. Increasing costs for labor, fuel, power, grinding media, reagants, and capital equipment have not been matched by the market price of the finished product. This cost-price squeeze has made it mandatory to reduce operating costs and improve the efficiency of the process to remain profitable. A number of other factors have added to the direct operating cost to make the problem even worse. These include environmental pressures to conserve natural resources and reduce smelter stack emissions; increased competition--especially from developing countries, varying economic conditions, stockpiling, governmental controls, and to top it all off, lower grade ore bodies. Although many of these other influences are good overall, they take their toll in cost per ton of delivered product. Fortunately, many operators are finding the solution to the cost-price squeeze in instrumentation and process control. Automated processes yield tighter spec. products, require less operating labor, produce more product from a given plant, and reduce unit cost by increasing process efficiency. The plant manager has a "handle" on the plant through process control so that he can change operating modes as economics dictate by changing the set point of some process controllers. He can even respond to economic conditions by switching control strategies from one that maximizes production to one that maximizes recovery, or minimizes unit cost, etc. This has all been made possible by the advent of on-line analytical instruments and practical process control computers. On-stream particle size (1), x-ray, and silica analyzers are now available and in use in many plants. Digital computer hardware and software has become practical so operators can use it without trying to become computer experts. This chapter describes the approach toward design and implementation of automatic grinding circuit control that has proven to be the most cost effective, based upon results from a number of

Jan 1, 1982

By Charles F. Ramseyer

The manufacture of iron and steel is one of the largest of our industries; and in point of size of single plant and equipment certainly the biggest of all industries. By the general public it is generally considered a prime example both of the marvelous technical advances achieved by modern science and engineering in the design and operation of equipment and of the efficiency of big business in the coordination of men and materials. Actually the operation of its basic processes has not changed significantly in either theory or fundamental design of equipment in the past 75 years. Though many other process industries have been born and developed, and not seldom completely revolutionized, during this period, the primary processes of making iron and steel are still carried out along the lines laid down, and in the equipment originated so long ago, by Bessemer, Siemens and Martin, and subsequently expanded to practically the modern scale by Carnegie, Schwab and Captain Bill Jones in the eighteen eighties and nineties. The application of the principles underlying the continuous counter-current physical and chemical interaction of solids, liquids and gases, which have been so successfully used in the rapid evolution of our chemical process industries, has been very largely lacking in the steel industry. In the days of the last-named giants, especially Carnegie, the steel industry made great and rapid technical progress. Carnegie's ever driving idea (as later with Ford in the production of automobiles) was the finding of new and better ways of making cheaper steel. Carnegie himself was a steelman, and so long as he dominated the industry its technical progress was rapid; and he, like Ford, was vastly successful financially as well, since his costs were continually being driven lower than those of his competitors by his advances in steelmaking technique.

Jan 1, 1935

By N. B. Pilling

THE development of a proper treatment for shells in connection with war contracts has brought to our attention the fact that the temperature of the liquid bath in which steel is quenched has a decided influence on the speed of cooling in the case of some liquids and very little in the case of others. Widely different physical results have been obtained by the use of water spray, water immersion, and oil immersion and further experiment has shown that the quenching effect of water used as a spray or an immersion varies greatly with the temperature of the water. The present experiments were undertaken with the idea of obtaining information of a quantitative nature regarding the quenching properties of a number of liquids used commercially in hardening steel. The general features of such cooling media are common knowledge and in the literature may be found records of numerous attempts to evaluate the cooling power of a liquid when used as a quenching bath. Much, if not most, of the data given on this subject is in the form of a simple statement of the time required for a certain heated mass to cool between two arbitrary temperatures when immersed in the liquid, quite regardless of the path of the temperature change. Our own purpose has been somewhat different. We have attempted to isolate that property of these. liquids having to do with their ability to absorb heat rapidly, as distinct from the behavior of a considerable mass when exposed to different thermal environments. More specifically, from the data obtained through autographically recorded cooling curves of a small standard mass quenched under various conditions, we have tried to analyze the mechanism of heat absorption by the several liquids, measure the changes in its rate as a function of the temperature of the surface of transference, and ascertain the influence of the temperature of -the liquid itself upon both.

Jan 9, 1919

By Henry H. Otto

The anthracite industry can be divided into two parts—the underground, or mining, and the outside, or preparation or manufacture. To understand recoveries in the two branches, some of the history of the industry and the changes that have taken place in the past century should be considered. It is a long step from 1807, when 55 tons were produced in the Wyoming field, to 1917, the peak year, when 80,841,223 tons were shipped to market from all the fields. In 1820, the Lehigh Coal Co., the predecessor of the Lehigh Coal & Navigation Co., shipped 365 tons in arks down the canal of the Lehigh Navigation Co. The Schuylkill field was not opened until 1822, when 1480 tons were shipped. The Wyoming field really became a producer in 1829, when 7000 tons were mined and shipped. It is well to note, at this time, the passing of the Coleraine colliery after a life of 88 years; in collieries of this age will be found the romance of the region, as well as the history of the changes to date. Mining Methods In the Lehigh region, the first coal came from the old quarry mines at Summit Hill; a little later the open-cut workings, or quarries, east of Jeansville, and near Beaver Meadow were opened. In the Wyoming field, it was necessary to resort to underground mining almost from the very first. Ashmead1 has described the changes in outside preparation methods, dl tending to increase the percentage of coal shipped to market. A description from the days when the lump coal was raked and screened out in the quarries or mines, to the modern breaker of today, shipping as high as 6000 tons of at least eight sizes of coal in an 8-hr. day is a very interesting story. Each size is a step toward increasing the yield from the property. With the belief that the supply was inexhaustible, the early mining was conducted with the thought of getting the maximum amount of coal on first mining. The superintendent was his own foreman and engineer.

Jan 1, 1925

By J. Allen Veatch

THERE exists in., the territory embraced between the summit of the Sierra Nevada and the coast a great dike and vein system that appears never to have been recognized in its entirety, nad many facts concerning it have never been published. This is important, not only in affording numerous clues bearing on the origin, nature, and age of the mercury deposits, and eliminating many controverted questions, but it. incidentally affords numerous facts bearing on the genesis of gold, copper, chromite, magnesite, dolomite, a type of calcite deposit, and numerous associated minerals. The mineral springs of the State almost without exception emanate from these dikes. A great range of the hydrocarbons also exists throughout the entire system of these dikes. Seepages from their, walls have frequently been mistaken as emanating from the inclosing sandstone and shale, resulting in heavy expenditures in the futile development of these Cretaceous beds, which contain no petroleum within the territory. The theory of mountain making by lateral or tangential pressure is inconsistent with some of the following recorded facts. The limitations of this paper do not admit of a description of each of the hundred or more mercury deposits embraced in the area, and therefore only typical examples will be described. The accompanying map, Fig. 1, is not submitted as complete, or as entirely accurate, but it is as nearly so as the notes at hand will admit. The field is too extensive to be completely covered by a single individual. The heavy continuous lines represent sections actually surveyed! The sections and extensions- in. dotted line are assumed, and are either unsurveyed, or -buried under younger beds. There are numerous branches connecting the great parallels that the small-scale map does not admit of plotting, even if the survey had been complete. Likewise, the conclusions in some instances may be faulty, but it is to be hoped that as a whole they may serve as a foundation on which a more complete structure may be built in the future.

Jan 2, 1914

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called' "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By M. H. Sommer

Many attempts have been made to develop a relation between the tensile properties and the deep-stamping qualities of metals commonly used in deep drawing. These operations are generally performed cold and the metal is always stressed beyond the elastic limit. However, the problem cannot be readily solved without a proper investigation of: (1) the relation between actual stress and actual strain in the plastic range and (2) the stresses that are set up in the metal during the process of deep stamping. Much work has been done in recent years to add to our knowledge on plastic deformation of metals and the shortcomings of the ordinary tensile test, particularly in the plastic range, have been sufficiently recognized. It has been widely acknowledged that the local contraction, which appears in a tensile test after the maximum load is reached, is not a general characteristic of the material but is peculiar to this form of testing. The plastic deformation of materials is explained by the slip of their crystals along certain planes and this rearrangement should be similar whether observed in a tensile, compression or torsion test, and if the results of any of these forms of testing show deviations, it must be due to other influences, as for example the local contraction in a tensile test. For this reason the tensile-test curve as obtained from the measurements taken on a tensile-test machine or registered by an autographic device has been supplemented by the so-called "actual stress-strain curve," which is constructed from the observed tensile-test data by eliminating the effect of local contraction and is in complete alignment with the stress-strain values obtained in a compresison or torsion test. The actual stress-strain curve shows the increase of actual unit stress in relation to unit elongation beyond the yield point and beyond the point of maximum load and indicates clearly the extent of strain-hardening which the ordinary tensile-test curve does not reveal. The following metals have been investigated in this paper and their actual stress-strain curves and, further, their char-

Jan 1, 1934

APRIL BEGAN with increased disorder in the Ruhr and some blood-shed. The war cloud in the East disappeared, however, with the signifi- cance by the Turks of their intention to return to Lausanne to negotiate a treaty of peace with the Allies. The French occupation of the Ruhr continued during April without there being any spectacular develop-ments. Of course there was surliness on the part of the Germans. In the meanwhile the statesmen on both sides were intimating what they might give and what they might take, sounding the sentiment of their respective populaces. The British Government found that its revenue for the last fiscal year has been greatly in excess of expenses. The surplus was applied to reduction of the debt. A consequence of this development has been a reduction in British taxes for the ensuing year, which has naturally created a much better feeling in Great Britain. On the other hand the unemployment situation in Great Britain caused increasing alarm. At the begin-ning of April about 1,500,000 men were out of work and the thought was developing that this might be not merely a temporary emergency, but a long continuing condition. The uneasiness of the workers themselves began to be exhibited in increasing strikes and threats of strikes. There were important domestic events during April. The six miners who were on trial in Illinois for the Herrin massacre were acquitted, following which the State dropped further prosecutions on the ground that Williamson County is so thoroughly under labor domina-tion that justice could not be had there. The Supreme Court of the United States on Apr. 10 handed down a decision that an act of Congress fixing minimum wages for women in the District of Columbia was unconstitu-tional, being interference with the freedom of contract included within the guarantees of the fifth amendment. Advances of wages became more general during April. The leading event under this head was the action of the United Steel Corporation putting into effect an.11 per cent. increase in the wages of common labor on Apr. 16, by virtue of which the rate per hour was raised from 36 c. to 40 c. This was dictated by competitive conditions, the labor difficulties of the steel industry being due less to a scarcity of men than their disinclination to take jobs in that industry while the building and other industries were paying as high as 60 c. per hour for similar work.

Jan 5, 1923

By Stirling Huntley

With the threatened falling off in production of the lighter oil pools of the Tampico embayment in Mexico, a general search of that country for oil-producing regions has resulted in renewed activity in the region of the Isthmus of Tehuantepec, one of the first districts exploited in Mexico. Since the drilling of the first well in the San Cristobal section by the Pearson interests in 1902, drilling has been continuous, except during 1917-1921, when practically all development was stopped by the revolutionary activity. Early in 1921, a drilling campaign was inaugurated for the purpose of testing out the known salt-dome poolfi on the flanks of the salt masses, rather than on their tops where previous tests had been located. On Dec. 7, 1921, the Aguila Co., with which are consolidated the Pearson interests and which has been the only company active in developing this region, unexpectedly drilled into a sand horizon at 3015 ft. with its Conception well No. 18. The hole was unable to handle the production, as a 1400-ft. string of 121/2-in. casing was hanging in the hole, a salt-water horizon drilled through at about 800 ft., was not cemented off, and 3000 ft. of 4-in. drill stem with rotary bit was in the hole. This well's potential capacity was never determined, but it made 7000 bbl. of 25" Bé. oil through the bit and Pin. drill stem, in one of its sporadic flows before sanding up, and thus proved itself capable of the largest potential production of any well on the Isthmus. The well showed salt water before caving and sanding up with the drill stem still in the hole, and will probably never be used for production. Wells Nos. 22 and 23, drilled nearby, have proved disappointments after making good showings of oil. In the spring of 1922, Ixhuatlan wells Nos. 28 and 29, deep tests supposedly on the flank of the known salt cores in that field, went into solid salt; No. 28 at 2250 ft. and No. 29 at 2400 ft. No. 28 was continued in the salt for 1000 ft. before operations were stopped. Later comple-

Jan 1, 1923