Search Documents

By M. M. Austin

Pure metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last, five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow. Strength and Ductility of Tantalum Since there is no good way of defining working properties numerically, illustrations will be used. It is possible to roll a bar of pure tantalum 0.4 in. thick to sheet 0.001 in. thick, without heating or annealing. The sheet produced will be sound and may be bent upon itself at right angles to the direction of rolling. Longitudinally the sheet will be somewhat brittle. A disk of annealed metal may be cupped and drawn to the form of a capsule 3/16 in. dia. by 146 1? in. long. If carefully handled this capsule can be further deformed by drawing to a tube having an outside diameter of 0.050 in. Disks of tantalum may be spun into tubes of 39 in. dia. and 1½ in. long. In the form of rod, reductions may be made from 0.4 in. to 0.001 dia. In the latter process, it is necessary to heat the wire four or five times to 500" C., at intervals between 0.040 and 0.001 in. Although the melting point of tantalum is 2850" C., these heatings at 500" C. are sufficient to distinctly anneal it. Published figures on the strength and ductility of tantalum are not particularly accurate. This is due to the fact that these properties vary widely, depending on the extent to which the metal is contaminated by gas. There are no sharp critical points in these changes with gas content; samples of metal will vary from a springy or actually brittle condition to one of leadlike softness. Samples that have had a prolonged heating at high temperatures in a good vacuum, under conditions such as would be provided in vacuum-tube experimentation, will yield a product of about the hardness of annealed copper. The usual commercial metal will have the hardness of annealed mild steel.

Jan 1, 1930

By A M. van Niekerk, W Mey

Coal mining has an impact on the water management of the water scarce Upper Olifants River Catchment. A prefeasibility study was carried out by Anglo Coal and Ingwe Collieries Limited to establish the water supply and demand in the catchment. A geohydrological model was used for the coalfields to determine the stored water and excess water available. Two distinct collective and treatment systems were proposed for the Witbank and Middelburg municipalities to treat excess water from the Anglo Coal and Ingwe Collieries Limited. The Emalahleni Water Reclamation Project for Witbank was initiated first. Water management and treatment experience gained at Anglo Coal was the cornerstone to develop the collection, treatment and distribution system. A full enquiry was issued to Keyplan, Veolia, Bateman Africa and IST Technik to construct, commission, operate and maintain a 20 ML/day desalination plant to treat acidic, saline mine waters to a South African National Standard (SANS) 0241 Class 0 potable water. After the technical and financial adjudication, Keyplan were awarded the contract. An integrated regulatory process was adopted through consultation with all the relevant regional and head office staff of the Department of Minerals and Energy, Department of Water Affairs and Forestry and the Mpumalanga Department of Land Affairs via an authorityÆs steering committee. A rock engineering evaluation was done to select both the plant and waste disposal sites as all possible sites are undermined. Various contracts are required with the individual mines for water supply, the Emalahleni Local Municipality for the delivery of potable water and for the disposal of wastes.

Jan 1, 2006

By Wengui Su, Qi Zhang, Junce Wang, Zhijun Ma, Xingyuan Weng

"Mesoporous materials with large specific surface area, pore size, and pore volume have been widely used in many fields such as ion exchange, gas separation, adsorption, and catalysis. Mesoporous materials prepared using natural zeolite have the advantages of both acid and alkali resistance. In this work, mesoporous materials were prepared using natural zeolite as the starting material and diethylenetriamine (DETA) as a template. The resulting samples were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 adsorption-desorption experiments. The influence of the crystallization temperature and crystallization time on the specific surface area, pore volume, pore size, and morphology of the resulting mesoporous materials are also discussed. Our results show that for an increase in both the crystallization temperature and time, the average pore size first increases then decreases, while the specific surface area first decreases then increases. Based on this work, we concluded that the optimal crystallization temperature was 2003 and the optimal crystallization time was 60 h. These conditions gave an average pore size of 17.93 nm, a pore volume of 0.048 cm3g-1, and a specific surface area of 16.48 m2g-1.INTRODUCTIONMesoporous zeolite, as the name implies, is a highly porous crystalline zeolite. This material is of interest due to its high hydrothermal stability, its adsorption and diffusion properties for macromolecules, and its excellent selectivity and activity as a catalyst. In recent years, it has become a hot spot among research of porous catalytic materials and has been widely used in petroleum and natural gas processing, fine chemical processing, various adsorption and separation tasks, and other uses (Carvalho & Urquieta- Gonzalez, 2015; Teh, Triwahyono, Jalil, Mukti, Aziz, & Shishido, 2015)."

Jan 1, 2016

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By T. G. Maepa

"The creation of mine excavations alters the stress distribution in the surrounding rock mass. In modern mining, resin-grouted rockbolts are used as a means of support in order to redistribute stresses and reestablish equilibrium in the rock mass. The success of resin-grouted rockbolting depends on the design of the system and the correct installation of the support units.The support design and rockbolt installation procedure at a platinum mine in the Bushveld Complex were investigated. A number of issues that resulted in poor installation were identified, including resin admixture, incorrect length and orientation of support holes, over- or under-spinning of the resin, and incorrect rockbolt tensioning. The support design used at the mine was reviewed and its limitations identified. A number of recommendations were made for optimizing the support design by reducing the diameter of the drill bit and reducing the length of the support holes. These changes will enable the mine to use different combinations of resin capsules. Implementation of the proposed changes will lead to a significant reduction in the cost of installation per support hole, as well as improve productivity and safety.IntroductionThe creation of any mine excavation disturbs the virgin state of stress in the Earth’s crust. This results in stress concentrations that interfere with the stability of the rock mass surrounding the excavation. It is essential to modify the internal behaviour of the rock mass surrounding excavations in order to reinforce the ground and stabilize excavations. Resin-grouted rockbolts are extensively used for this purpose. Esterhuizen (2014) stated that when effectively installed, the rockbolt exerts a clamping force and a bonding strength that keeps the rock mass together. This increases the cohesive strength of all discontinuities in the rock mass and enhances the stability of the excavation. Poorly designed and installed ground support is ineffective and constitutes a safety hazard. It is therefore crucial for every mine to ensure that any form of ground support is designed and installed correctly. This research evaluates the installation of resign-grouted rockbolts and identifies challenges and solutions for improved safety as observed at an operating hard rock mine. The support design used at the mine was reviewed and the design parameters optimized. The outcomes will enhance the efficiency of support and minimize the costs associated with the installation of resingrouted rockbolts."

Jan 1, 2017

By Henry P. Ehrlinger, James C. Bradbury

Tripoli is a naturally occurring, very finely divided form of silica found chiefly in some midwestern and southeastern states and used commercially as fillers and abrasives. Definitions Tripoli is a microcrystalline, finely particulate, more or less friable form of silica that appears to be the product of leaching of siliceous limestone or calcareous chert. The term was originally applied to a deposit near Seneca, Mo., that resembled material of that name found near Tripoli in North Africa (Hovey, 1894). The two deposits were subsequently found to have different physical characteristics -the North African tripoli, now called tripolite, is a diatomite, composed of the siliceous skeletons of microscopic marine plants called diatoms, and the Missouri tripoli contains no diatom remains; the term tripoli, however, continued to be used for the Missouri material and is now applied in a general way to most silica deposits similar to it in characteristics and geologic origin. In commercial trade tripoli is commonly understood to designate material from the Missouri-Oklahoma field; silica from southern Illinois, the other major producing area, is referred to commercially as amorphous silica. Each term, however, may be used commercially for material, regardless of place of origin, that has the characteristics or uses commonly ascribed to the material from one or the other major producing area. For example, in the commodity price listings, Engineering and Mining Journal routinely lists under Tripoli, prices "f.0.b. Elco, III." and "f.0.b. Seneca, Mo., and Rogers, Ark.," and under Silica, amorphous, prices "f .o.b. Ill.," and "f .o.b. Dierks, Ark." Amorphous silica, the commercial designation given to southern Illinois tripoli, is, like the term tripoli, a misnomer. Mineralogically, the southern Illinois deposits are composed of microcrystalline quartz, and no amorphous material has been detected during X-ray and scanning electron microscope investigations (Leamnson, Thomas, and Ehrlinger, 1969; Thomas et al., 1970). Soft silica is another term that has been applied to Illinois and Tennessee tripoli, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, produced by pulverizing silica sand (Heinz, 1937). Rottenstone, produced commercially in Pennsylvania, is similar to tripoli in that a major constituent is finely particulate silica, and its uses are much the same as those of tripoli- as abrasives and fillers. The origin of rottenstone also is similar to that of tripoli-decomposition of a siliceous sedimentary rock. The parent rock is defined as a siliceous limestone (Gary, McAfee, and Wolf, 1972; Thrush, 1968) or as shale (personal communication). Heinz (1937) quotes a brief statement describ-

Jan 1, 1975

By E. G. Woodruff

The earlier struggles in petroleum geology were directed to solving the Qrigin and method of accumulation of petroleum. We are now fairly well agreed on those subjects. Most of us think that the great mass of petroleum commercially produced comes from plants or animals, or possibly from both. We are confident that the oil was not produced where it is now found but has accumulated in reservoirs of various kinds. The types of reservoirs are certainly variable but they just .as certainly follow definite geologic laws. Some of these types of reservoirs can be determined from surface study; others cannot. We know, too, that these types of reservoirs (largely structures such as anticlines, domes, and terraces) are much more widespread than the oil pools. In other words, there are many places where good sands and good structures exist but where oil is not found. It is the purpose of this paper, therefore, to attempt to analyze, from a regional standpoint, some of the conditions that control the presence or absence of oil pools and to group them in a regional way, hence the term "Petroliferous Provinces." The paper lays no claim to presenting new facts but attempts to group and classify the information that so many have expressed again and again. The essential factors for an oil field are petroleum, a reservoir material, and conditions under which the petroleum can enter the reservoir but cannot escape except through the drill holes. The paper will first discuss the source of petroleum as it occurs in definite regions, then the regional arrangement of reservoir strata, and finally the areal arrangement of structures. To have petroleum, there must be a source. Since living matter is considered the source of the petroleum, geological conditions must have been such that living organisms were abundant. Arid regions on the earth's surface have not given rise to living things in sufficient abundance to produce oil; similarly, too cold regions and saline inland lakes. The converse of this is that warm moist conditions must prevail to produce an abundance of vegetable matter. Before an area can be

Jan 1, 1921

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By Yu. Gurevich, M. Teremova, I. Prokopev, A. Razvjaznaya, N. Algebraistova

"The objective of this work is the scientific justification and development of efficient and environmentally-friendly method of bulk concentrate preparation for selection with application of microbiological practices. This research suggests to apply Pseudomonas Japonica bacterial culture to the bulk concentrate before the selection circuit in order to clear the surface of sulphides from the xanthate skin. It is also suggested to apply bacterial consortium Ochrobactrum ?nthropi and Pseudomonas aeruginosa JCM 5962 for desorption of diesel residual concentrations. High-efficient and environmentally friendly method of copper-molybdene and lead-zinc bulk concentrate selection was developed based on theoretical and experimental research work with application of microbiological practices. In comparison with conventional methods (steaming, sodium sulphide washing) the above suggested bio-technological method of bulk concentrate preparation before selection cycle will allow to reduce material and power expenditures, and it is also environmentally friendly. INTRODUCTION High-efficient selection of sulphide bulk concentrate is gained exclusively after collecting agent is removed from mineral surface. Therefore, the problem of bulk concentrate preparing before the selection cycle is acute, since the further technological parameters of the subsequent separation depends on the effectiveness of pulp preparation. Existing traditional ways of bulk concentrate preparation. such as washing or steaming, are characterized by high energy and material costs in industrial conditions [1,2]. The microbiological treatment before separation of the bulk concentrate into different kind of concentrates appear one of perspective processes for treatment of bulk concentrates [3,4]. At the present time, the world practice of processing mineral raw materials demonstrates the wide application of technologies using microorganisms: bacterial leaching and oxidation, purification of industrial wastewater. This is due to the fact that biotechnological methods are environmentally safe, low-cost, and suitable for refining complex ores and raw materials of industrial origin."

Jan 1, 2018

By P Valenzuela

Joint mapping is a fundamental input for rock mass characterisation and slope stability analysis. The usual way to do it is using a compass in the field or digitising structures on a screen, with a software package.In this paper a method to identify and map joints automatically along a rock face is presented; it is called the Concentric Shells (CS) algorithm. The method scans a point cloud sequentially, tests if selected points are ‘true pivots’ within an inner shell, and then it searches for points inside a wider sphere (outer shell).The algorithm, developed by the author, was applied in real data. It reproduces the main features obtained from conventional (compass) and digital mapping (software package). Execution times are approximately 45 seconds for two point sets holding of 3.1 million points. Obtaining the same results via digital mapping takes approximately 3–4 working days.Key advantages of this method are: significant time reductions; elimination of mapping bias; and the ability to manage very large data sets (>2 million points) without the need of scanning the cloud on the screen. These advantages make this method an attractive tool for engineers and geologists wanting to increase productivity.CITATION:Valenzuela, P, 2017. Automated joint mapping using the concentric shells algorithm, in Proceedings Tenth International Mining Geology Conference 2017, pp 257–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By I. R. Taylor

Union Carbide has recently developed two open- pit vanadium mines in the Wilson Srpings area of central Arkansas about five miles southeast of Hot Springs. The ores from these mines, together with those from a larger vanadium deposit at nearby Magnet Cove, are processed at a new 1600- tpd plant built by the company in the immediate vicinity (Fig. 1). The Wilson Springs vanadium deposits are associated with the Potash Sulfur Springs intrusive, a circular igneous complex which is exposed over an area that is somewhat less than a mile in diameter.1 The complex has a crude ring structure similar to that of the larger Magnet Cove instrusive six miles to the east.2

Jan 4, 1969

By Stanley B. Roboff

Throughout the world nuclear power re- actors are being designed and constructed as the energy source for stationary power plants. They are built to power submarines, surface ships, and long-range aircraft and to provide small package power plants that can be set up with relative ease in outlying areas. Regardless of type, most of these plants are designed to operate at the highest permissible temperatures and with the greatest possible burn-up of fuel. On paper it is now possible to design a nuclear power plant that will out-perform all existing types of power-generating plants, and at costs which are attractive. Such plants, however, are not now being built, nor will they ever be built, unless major engineering advances are made in the realm of reactor materials. The reason for this is straight- forward enough. Although it is known that huge quantities of energy can be generated in nuclear fuels within short periods of time, as yet there are no construction materials capable of withstanding the severe conditions that would exist within a power reactor operating with ultrahigh output.

Sep 1, 1956

By B. Rao Pothini, Hilmar A. von Schonfeldt

One of the key elements essential to a productive and uninterrupted longwall mining operation is roof control. In several of the Island Creek Coal Company's mining sections, polyurethane has been infused 80 into strata to control severe roof failures in the face and gate entry areas. To date about 50,000 kgs (110,000 lbs) of the chemical have been consumed in a number of applications. Roof-to-floor convergence 60 and differential roof sag have been monitored to determine the need for polyurethane infusion and also to evaluate roof stability following the infusion. Stratascopic observations of the roof formed the basis 40 for confirming the need and also for estimating the required quantities of polyurethane. Both chemical infusion and roof control monitoring techniques have been applied successfully under very adverse roof 20 conditions; substantial production benefits have been realized. Operator acceptance of the system has been very good.

Jan 1, 1981

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

In March 1962, over three months ahead of schedule, production began from the Ventersdorp Contact Reef of the Western Deep Levels Ltd. mine on the West Witwatersrand. Few mines have captured the interest of mining men and the public as has Western Deep Levels. It has presented the gold mining industry with a challenge which involved the opening of an ultradeep mine with the attendant problems of exceptionally heavy capital commitments ($77 million to start of production), high rock temperatures and pressures at great depths, cementation and pumping in an area notorious for the volume of subsurface water, and the necessity for entirely new thinking and the application of new ideas. HISTORY Not all the problems facing Western Deep Levels were, however, new. Situated 43 miles from Johannesburg, just off the main road to Potchefstroom, Western Deep Levels was the sixth company to undertake mining operations on what is known as the West Wits line and it could draw on the wealth of experience gained by other pioneer mines in the area.

Jan 12, 1962

By W. K. Osae

A value assessment model which uses deal objectives, financial and non-financial indicators as a guide to assess value creation in mergers and acquisitions. The extent to which post- merger deal objectives are achieved and the potential benefits derived from mining deals that may not necessarily be financial of nature, but which are necessary to sustain and enhance future performance, were considered. The pre-merger and post-merger performances based on some financial indicators that reflect profitability for shareholders were also used. This value assessment model was used to assess four major deals that have occurred in the South African mining industry since 2003 as part of a postgraduate dissertation. In this paper, the Harmony and ARMgold merger is used as an example of how the model can be applied. The model?s relevance and applicability can also serve as a guideline in developing a framework or holistic guideline in assessing whether mining BEE deals in South Africa create value.

Jan 1, 2011

In the wake of the financial crisis that affected world markets in 2002, there has been an increasing international focus on corporate governance. Various corporate governance codes of practice have been introduced, such as the Sarbanes-Oxley legislation in the USA, the Combined Code in the UK, and King III in South Africa. This focus on corporate governance has increased since the most recent financial crisis in 2008, the effects of which are still being felt world-wide. In the mining and minerals industry, reliable metal accounting is essential to sound corporate governance and is also becoming a focus of increased attention and concern, particularly as the figures generated by the metal accounting system feed directly into the financial accounts of mining companies. Mass measurement, sampling, and analysis provide the input data for the metal accounting system and sound corporate governance requires that the procedures used are based on best practice and that the data generated is accurate and handled correctly, transparently, and consistently to produce the accounting reports. The AMIRA Code of Practice for Metal Accounting has been widely adopted in the industry as a means to achieve this, and the compilers of the Code have conducted numerous metal accounting audits at operations, both in South Africa and abroad. These audits have shown that there is a real need for such a code of practice. Keywords metal accounting, AMIRA Code, corporate governance, risk management.

Jan 1, 2014

This is a brief introduction of a sewer pipeline constructed with a pipe jacking method in combination with a 1 200 mm finished inner diameter tunnel boring machine developed for the first time in Japan. The pipeline is located under a national highway running through a densely built urban area and is 185.7 m long and 2.9 m to 3.7 m deep from the ground surface. The geological features along the pipeline show mostly slate and partly silt. The pipeline was constructed with a newly developed multi-application type tunnel boring machine equiped with a fluid transport system. The construction consisted of tunneling by a tunnel boring machine followed by pipe jacking operations. The excavated materials were dis- charged off the tunnel by a fluid transport System.

Jan 1, 1987

By Harold F. Unger

The Bureau of Mines conducted drilling experiments in the laboratory with a commercially available percussive drill that has an independent rotational system. Eight rock types with a wide range of physical properties were drilled under several combinations of rotational speed, drilling thrust, and operating pressure. Penetration rates and energy per unit volume correlated well with the coefficient of rock strength as shown graphically. Size-distribution analyses of some of the drill cuttings show how particle size varies with rotation speed and rock hardness. In general, changing the rotational speed has a greater influence on the penetration rate in softer rocks, with penetration rate increasing with increasing rotational speed.

Jan 1, 1972

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981