Search Documents

By Askew J. E

All facets of current practices of cable dowelling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited are re- viewed. This includes materials specific- ations, installation practices and design pro- cedures. Cable dowelling for cut and fill stoping, square set timber stoping, longhole open stoping and level reinforcement is considered. Installation is simple and can be mechanised to eliminate heavy lifting. Quality control is essential for optimum performance of the re- inforcement. Design patterns must consider the mining method, reinforcement economics, acceptable stability standards and mine production priorities.

Jan 1, 1977

By B. Amero, W. Petruk, D. R. Owens, D. R. Morris

Samples taken at different heights in the lead blast furnace of Brunswick Mining and Smelting corporation were studied to determine the phases present in order to interpret the reactions In the furnace. The main phases in the blast furnace feed are Pb3Ca2S13011, Zn ferrite (ZnFe204), and hardystonite (Ca2ZnSi207); rninor ones include lead and a Pb silicate. The temperature in the furnace varies from about 300°C at 4.2 m above the tuyeres to 1150°C at 1.1 m. There is no evidence of reactions in samples from points cooler than 800°C. Some reaction occurs between 950° and llOO°C and the lead sinter is nearly decomposed at about 1150°C. The first evidence of reaction was the decomposition of Pb silicate to lead and S102. At higher temperatures the Pb Ca2Si3011 decomposed to form lead and hardystonite (Ca2ZnS120rf. The Zn required for hardystonite was derived from the Zn ferrite which apparently re-equilibrated to a new Zn ferrite with less Zn. The decomposed sinter consists essentially of lead, hardystonite, wustite and a Zn ferrite with a low Zn content.

Jan 1, 1984

By H. J. Fisher, J. L. Walter

Two types of Si-Fe columnar ingots with preferred crystal orientation have been produced: a) ingots with (0011 directions of the crystals parallel to the longitudinal ingot axis and b) seeded ingots in which all crystals have the (100) [001]orientation with respect to the sides of the ingot. Measurements of freezing rates and temperature gradients indicated that columnar freezing occurred as long as the temperature gradient ahead of the solidification front was greater than zero. THE development of preferred orientations or textures in wrought metals may be influenced by the presence of a preferred crystal orientation in the ingot from which the product was made. The deliberate introduction of preferred orientation in the ingot for the express purpose of producing a particular preferred orientation in the wrought product has not, to the authors' knowledge, been reported in the literature.* This report describes the prepara- tion of ingots of 3 1/4 pct Si-Fe in which preferred orientations near (100) [001] were produced. These ingots were subsequently rolled to strip, 0.012 in. thick, to provide a sufficient quantity of polycrystal-line sheet having the (100) [001] orientation or "cube-texture" to evaluate the magnetic properties. The properties; and test results showing the advantage of the cube-textured Si-Fe magnetic sheet over magnetic sheel having the (110) [001] texture or "Goss" texture have been reported elsewhere.' The rolling and recrystallization textures of single crystals of silicon-iron having orientations near (100) [001] have been studied by Walter and Hibbard.2 They found that if the crystal has an original orientation such that the (100) plane is within 30 deg of the rolling plane, the recrystallization orientation will approach (100) [001]. If the (110) plane is nearly parallel to the rolling plane,

Jan 1, 1962

By J. Norman Bulkley

As electrical power is used to a greater extent on the Rand than in any other mining center, it is thought that a short description of the methods used and results obtained may be of interest. In comparing Rand practice with that on other fields, several general factors should be borne in mind: First, the mines are all working on large tonnages of low-grade ore (average. $6.50). The annual crushing rate is about 27,000,000 tons. Second, the mines are all grouped udder the financial and engineering control of mining houses, so that the results of a group, rather than an individual mine, are open for study, and practice follows more uniform lines. Third, coal of fair quality (about 12,000 B.t.u.) can be obtained for $2 to $3 per ton., Good supplies of condensing water are, however, scarce, and have to be carefully stored. Power Supply Power is supplied by the Victoria Falls & Transvaal Power Co., Ltd., and its subsidiary, the Rand Mines Power Supply Co. Both companies, which are practically one from an engineering point of view, operate the following stations, all feeding into the same system.

Jan 2, 1916

By Fred Leighton, Wilson Blake

The microseismic method of detecting instability and high-stress zones in underground mines was developed by the U.S. Bureau of Mines (USBM) in the early 1940's.l,2 For about 25 years this method has been used throughout the world by mining and construction companies in assessing the stability of underground and surface excavations. Rock noises are the release of small amounts of stored strain energy propagating outward from their source as a seismic wave that can be detected with special geophysical equipment. This release of strain energy is caused by a rock mass undergoing load changes resulting in small-scale displacement adjustments such as microcracking, shearing, sliding, and crushing of crystal grains, some even as small as the elastic displacements themselves. No detailed field studies of any of these mechanisms have been made, and knowledge about the origin of rock noises is relatively incomplete. Laboratory tests have shown that when rocks are stressed in a testing machine, the rock noise rate-the number of rock noises generated per unit of time increases with increasing applied stress.3 This increase is most pronounced as the ultimate strength of the rock is approached. The standard field procedure has been to monitor a rock structure at intervals and plot rock noise rates vs. time, thus gaining a semiquantitative estimate of the behavior and stability of the structure. The success of such monitoring, however, has depended almost entirely on the experience and knowledge of the operator, his interpretation of the data, and his equipment. Very little study has been devoted to the basic properties of the vibration record of a rock noise. USBM decided that the microseismic method was being used sufficiently by various mining and construction companies

Jan 1, 1970

By J. F. Myers, F. M. Lewis

The Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accomplished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1943

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By Fabjanczyk M. W

Artificial ground support has developed into a refined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bolt is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By C Philander

The West Coast of South Africa is well known for its placer gem quality diamond deposits and also associated with these hosts of Cenozoic unconsolidated marine and aeolian sand and gravel are significant concentrations of heavy minerals. Exploration for economic concentrations of zircon, ilmenite and rutile along the coast started in the mid-1980s. This resulted in the discovery of an inferred 1.6 billion tonne resource with a grade of ten per cent total heavy minerals (THM), which developed into the Namakwa Sands Mine, a world-class producer of heavy minerals. Several other resources, including satellite deposits proximal and distal to the mine area, extensive diamond mine dumps and present day beach placers, demonstrate the vast heavy mineral potential along the West Coast. The favourable gangue to economic mineral ratio, a higher zircon content compared to other similar deposits, relatively lower U+TH content of zircon, low slimes content and effectively pristine low chromium-manganese ilmenite of these deposits, render them attractive exploration targets. Negative factors that will affect conventional mineral beneficiation and liberation include secondary mineral coatings and the regional coastal development of several layers of superimposed duricrust. The economically attractive heavy mineral assemblage along the West Coast is the result of erosion of the proximal, gneissic Namaqualand Metamorphic Province and mature Table Mountain Group sandstone, concentration by marine and aeolian processes and preservation under arid climatological conditions over a period of more than 100 Ma.

Jan 1, 2008

By R. W. Baldwin

As used in geophysical exploration, the term overvoltage applies to secondary voltages set up by a current into the earth which decay when the current is interrupted. These secondary effects may be measured by pick-up electrodes. The term induced polarization has often been employed to describe this same phenomenon. In its own operations Newmont Exploration Ltd. commonly uses the word pulse. The basis of this method in prospecting is that metallic particles, sulfides in particular, give a high response, whereas barren rock, with certain exceptions, gives a low response. Overvoltage has been tried in searching for many types of mineral occurrence but has been most successful in outlining the widespread disseminated mineralization associated with porphyry coppers. History:' Newmont Mining Corp. has been interested in overvoltage since 1946, when Radio Frequency Laboratories of Boonton, N. J.. drew the company's attention to phenomena observed in the laboratory. At the instigation of A. A. Brant further model studies were undertaken, and the first tests were performed in 1947. Tests at San Manuel, Ariz., in 1948 were very encouraging, clearly demonstrating that the method could be used to distinguish scattered sulfides at depth. H. 0. Seigel followed up the San Manuel work with a study to determine the phenomena involved.'

Jan 1, 1960

By C V. Putnis, T Geisler, A Putnis

In nature, ilmenite (FeTiO3) undergoes weathering through oxidation and removal of Fe to form an apparently continuous series of compositions from ilmenite to pseudorutile (ideally Fe2Ti3O9), and with further weathering, to leucoxene. To determine the mechanism of acid-leaching of ilmenite to ultimately form rutile, we have carried out an experimental study of ilmenite alteration in autoclaves at 150¦C in HCl solutions. Resulting products were studied by X-ray diffraction, scanning electron microscopy, electron microprobe and Raman spectroscopy. In some experiments the solution was initially enriched in 18O and the distribution of the isotope in the alteration products mapped from the peak shift in the Raman spectra. The results indicate that the alteration may proceed in two stages, each with a sharp interface between the parent phase and the product. The alteration begins at the original ilmenite crystal surface and along cracks through which the fluid can migrate. The first alteration product is pseudorutile û no phases intermediate between ilmenite and pseudorutile were detected. The textural relationship between ilmenite and pseudorutile suggests a coupled dissolution-reprecipitation mechanism rather than a solid state continuous oxidation and Fe diffusion mechanism. The second stage involves a further dissolution-reprecipitation step to form rutile. Raman spectroscopy shows that the 18O is incorporated in the rutile during the recrystallisation. Throughout the alteration process the original morphology of the ilmenite is preserved although the product is highly porous. The rutile inherits crystallographic information from the parent ilmenite, resulting in a triply-twinned rutile microstructure.

Jan 1, 2008

By Weyer J

Many existing computer planning programs for the mining industry focus either on big mining enterprises with a high production rate or on smaller operations for high value minerals. Big mining enterprises, like the hardcoal company `Ruhrkohle AG' in Germany have their own R&D departments which develop powerful computer programs for planning purposes, partly in co-operation with mining universities. However, there is a remarkable number of small- scale mining operations which are either not able to buy expensive hard- and software or don't have the skills for the operation of extensive software programs. Partly there is also a trend in using rule of thumb calculations rather than computer programs which need a lot of - partly unavailable - data. For this reason a computer program was developed which does not need expensive hardware and software and which can help the planning engineer in the selection of a limited number of possibilities. Until this time the planning engineer established two or three different cases and calculated the results with a pocket calculator. This could last some hours or even some days. Now he or she can use the computer program with a normal PC to compare the cases. All activities are menu-driven. The basis for all, calculations are fixed and variable costs as well as average performance for special activities. The paper gives an example for a possible planning situation in fluorspar mining (originally this program was developed for the fluorspar enterprise Lengenfeld in Germany). It shows the initial situation, the main structure of the program, the input logic and the results. Benefits, limits and possible extensions of the program are discussed.

Jan 1, 1995

By S. E. Khalafalla

The ability of potentiometric, gas-sensing electrodes to reliably monitor free gaseous molecules in solution has been recently demonstrated. A gas such as sulfur dioxide from a dilute sample solution diffuses through a hydrophobic, gas-permeable membrane to an internal filling solution. The latter solution contains a sufficiently large excess of sodium bisulfite, the concentration of which can be considered constant regardless of the quantity of sulfur dioxide entering by diffusion. The electrode response is essentially due to the liberated hydrogen ions from the bisulfite-sulfur dioxide equilibrium. This Bureau of Mines report describes a new technique used to detect the formation, and to estimate the stability constant, of gas-molecule and gas-ion complexes in solution, as part of an effort to minimize the undesirable environmental impacts associated with mining and mineral processing. Although the unknown activity coefficients of the neutral and ionic species in the external solution complicate the quantitation of results, methods to circumvent these difficulties are presented. The technique is based on the isometric shift of the Nernst diagram of ion-selective electrodes to higher concentrations relative to the standard aqueous calibration curve. The method is applied to detect and estimate the formation constant of a sulfitocitrate complex, and agrees well with an independently determined stability constant of the disulfitomercu-rate complex.

Jan 1, 1978

By Bret K. Clayton

Jan 1, 2004

By K. J. Yang

Based on investigations and model tests combined with pile foundation on Code compilation of drydocks, we present this report to give informations against uplift pressure of piles beneath floor of drydock. In a same kind of soil, we have got comparative tests results with single pile and pile group, and the latter was performed at different spacings, different embedded depths and different number of piles in the group. Having analyzed through the results, there are some new understandings of regularity about failure mechanism and uplifting capacity of single pile and pile group, as well as optimum embedded depth of pile foundation. The results of research approach to measured values of full-scale and model tests at home and abroad, it has been placed into the Design Code of Drydock in China (1985), and can give a reference to design of pile foundation at sea and on land under uplift loading.

Jan 1, 2010

INDEX OF CONTENTSIntroduction.Systems of classification of coals.RankClassification of Australian coals.Defects of systems in use in other countries.Indexing by Fuel Ratio.Classification by Ultimate Carbon/Ultimate Hydrogen.Relationship between Fuel Ratio and ultimate composition.Suggested convention for classification.Origin and Evolution.Notes on directions of change of composition on Carbon Hydrogen chart.Summary and conclusion.Acknowledgments.Bibliography.Appendix.

Jan 1, 1948

By Surinder Singh, Vassilios Kazakidis, Damian Gregory

Safety, stability, and functionality of mine excavations depend on the structural integrity of the surrounding rock mass. Various explosives and perimeter control blasting techniques have been developed in order to minimize rock damage associated with the conventional drilling and blasting operations. The success of perimeter control blasting depends on many factors grouped in three categories: rock mass features, blast design and implementation, and explosive parameters.

Jan 1, 2008

By Dhanvin B. Mehta

Pile testing is generally understood as static load test. It is our common experience that for high capacity, large diameter bored piles, static testing is expensive and time consuming. It is practically impossible to test large number of piles by traditional testing methods. The escalating cost in carrying out a static load test, as well as incomplete information derived therefrom compelled researchers in United States to look for an alternative method of testing for both bored and driven piles. The original research work was carried out at Case Western Reserve University in early 70's, under the funding of Federal Highway Administration as well as several State Depts. of transportation in United States. The outcome of the research was the development of a state of art field computer for capacity determination, based onOne Dimensional Wave Mechanics.

Jan 1, 1996

By A. M. Marabini, G. Belardi, E. Spaziani

The objective of this research was to investigate the possible application of integrated circuits to the concentration of talc from the Valmalenco mine, located in northern Italy. The investigation was aimed at producing a high-grade product (low in impurities such as iron and carbonate) that would be suitable for industrial applications. Because of the presence of accessory minerals, the talc concentrate from this ore is not, at the present time, suitable for industrial applications.

Jan 1, 1996

By O. E. Kiessling

THIS announcement of the topics relating to production control, which the Committee hopes to have discussed at the February meeting, supplements the preliminary announcement published in the November number of MINING AND METALLURGY. In the previous article, the writer indicated the kaleide-scopic nature of the questions involved in obtaining better coordination in industry, and that, as a matter of practical expediency, the discussion in February would be limited to the more obvious difficulties in industry which need attention and to those questions which the Committee thinks would be of greatest interest to members of the Institute. But while practical considerations necessitate limiting the program, free discussion of all phases of the subject is urged by 'the Committee. In a preliminary consideration of the production control problem, there loom up two questions which have to be faced: (1) First, there is the question of the extra industrial capacity necessary to meet demand during the ordinary fluctuations of business, commonly characterized as `the "business cycle." Anyone who tries to formulate a program pertaining to productive capacity must decide whether he wishes to discuss the control of business cycles. While this question may eventually lend itself to treatment, the Committee does not feel that it can be considered at present with much profit. (2) The second question arises from the existence of over-stimulated capacity above and beyond peak demands in boom times. Discussion of this topic, it is felt, would be most fruitful. How to prevent capacity from being over-stimulated to an extent beyond any hope of possible demand is a

Jan 1, 1929