Search Documents

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931

By Chester Purington

THE AUTHOR hopes that this paper will meet with criticism and debate by fellow members of the Institute rather than with that attitude of passiv-ity and indifference which one is inclined to adopt when considering a field completely foreign to one's own experi-ence. After several years of study of voluminous literature, maps, and statistics, and many personal journeys and field inspections of various parts of Siberia, the conclusion is reached .that the area adjacent to the Stanovoi, Zhugd-Zhur, and Yablonoi ranges as below defined is that which .is most accessible to the western world and will soonest give results from exploration. HISTORY The first incursion of the Russians into Siberia east of the Yenesei River appears to have been in 1632 when the fort of Yakutsk was founded on the middle Lena. The early expeditions were in quest of furs. As the Siberians say, "the sable beckoned" and the post of Anadyr was founded in 1639, two thousand miles further northeast. Thus nineteen years after the Pilgrims landed in Massachusetts, the Russians had established a trading post within 700 miles of what is now the town of Nome, Alaska. Parties of Cossaks penetrated to the shores of the Okotsk1 Sea early in the seventeenth century, but it was not until 1688 that the town of Okotsk was founded. In 1712 a grand project was elaborated at St. Petersburg for building a port at Okotsk, but it came to nothing. Vitus Bering, the Alaska explorer, built ships at Okotsk, and made this his point of depar-ture. It is stated that the iron work used in these ships was brought overland partly from Yakutsk, and partly even from St. Petersburg, 5500 miles away. Accord-ing to report a copper deposit was worked on the river Urak, not far from the coast, and copper was smelted for sheathing the bottoms. Grassgrown mounds con-taining slag and shots of copper were inspected by the writer last summer, at the site of the ancient shipyard.

Jan 11, 1923

Provide an effective method for "soft" soldering aluminum and aluminum alloys using conventional tin-lead solder alloys and flukes. The Problem In the past, it was virtually impossible to solder aluminum and aluminum alloys using standard tin-lead soldering systems (solder and flux) due to the presence of an aluminum oxide surface film which forms instantly on aluminum and aluminum alloys when these are exposed to air. The tenacious and stable oxide film enables aluminum-base materials to maintain their bright luster. But the film also prevents the required wetting and spreading of solder on the substrate, causing the loss of adhesion between the solder and the substrate. In addition, the heat produced during soldering increases

Jan 1, 1983

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,000. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service.

Jan 1, 1946

By G. R. Sawyer

Although backfilling has been in operation for many years, the methods for selecting appropriate slurry dewatering aids have, in some cases, been rather unsophisticated. This has led to many misconceptions regarding the role of the dewatering aid and its various means of application. Testing procedures employed in the correct selection of any practically applied dewatering aid must mirror the actual working processes in which they are to be used. This constraint necessitates the development of complex testing methods when applied to backfilling. The current testing procedures were scrutinized and their various merits noted. From this study a series of testing methods was evolved which incorporate the best aspects of these testing procedures with novel ideas which would eventually result in the correct selection of the dewatering aid. A major consideration in the application of any of these methods is the modus operandi of the backfilling process, and the relevance of the tests to the process. This work attempts to consolidate the testwork performed in the past and suggest new approaches in the correct selection of acceptable dewatering aids for backfilling.

Jan 1, 1988

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By Charles A. Anderson

THE Bagdad copper deposit is of the disseminated type (porphyry copper) occurring in a quartz monzonite stock of late Cretaceous or early Tertiary age. This stock, located essentially at the intersection of two dike swarms, is the only one of several stocks cropping out in the area which is appreciably fractured and mineralized. Most of the rocks in the area are of pre-Cambrian age, but their structures have had no discernible influence on the copper mineralization. Hypogene alteration of the quartz monzonite includes the addition of quartz, orthoclase, and sericite and recrystallization of biotite. The hypogene sulphides are pyrite, chalcopyrite, and molybdenite, the latter younger than the chalcopyrite. The late Cretaceous or early Tertiary igneous rocks, veins, and faults were controlled by northeast and northwest shear zones, the intersection of which marks the zone of appreciable copper mineralization. The minor mineralized fractures carrying the bulk of the copper have a preferred orientation parallel to the intersecting shears, and it is concluded that they are of tectonic origin rather than the result of shrinkage on cooling, crystallization, or mineralization. Supergene enrichment during late Tertiary or early Pleistocene time formed a chalcocite zone providing the minable copper ore. The enrichment was controlled in large part by northeast and northwest faults, particularly at their intersection or where the faults are closely spaced.

Jan 1, 1947

By H. Kurokawa

Sumitomo Metal Mining decided to expand copper production capacity of Toyo Smelter and Refinery to cope with the recent copper demand growth in Asia, and to survive by reducing cost. The expansion plan is promoted to increase electrorefined copper production capacity from 270,000 metric tons in 2001 to 450,000 metric tons in 2007. The major changes in smelting section are introduction of the rotary steam dryer, renewal of the feeding system for flash furnace, improvement of the concentrate burner, modification of the flash furnace cooling materials, renewal of the slag cleaning furnace, modification of the flash furnace waste heat boiler, installment of a new converter furnace, enlargement of two anode furnaces. In addition, the gas cleaning system was upgraded and the second acid plant was installed. In the refinery section, the existing tank houses have been operated at high current density of 300A/m2 using the conventional starting sheet cathode technology and moreover a new tank house utilizing the permanent cathode technology was constructed. Although the copper production capacity has been increased, SO2 emission has been kept the lowest in the world through consideration of influence on the environment by expansion project.

Jan 1, 2006

By Arthur Phillips

DURING the past few years considerable interest has been shown in the study of fiber, and its effect, in wrought metals. Fiber has recently been defined as a "condition of parallelism of important lines or details in the structure. "1 Briefly stated, two distinct types of fiber are commonly encountered. One results from the alignment in the direction of working of constituents, more or less segregated, such as slag, oxides, carbides and dendritic formations. The second, and least understood, type is produced by working the metal below the recrystallization temperature in such a way as to develop a parallelism of the grains. This condition is readily recognized by the pronounced elongation of the grains in the direction of working. Under certain deformational treatments the grain fragments produced by cold working tend to orient in certain definite directions with respect to the axis of extension. Furthermore, even in metals that have been annealed after cold working preferred orientations may be present. It is perhaps logical to assume that such marked parallelism of structural elements would be manifested by directional properties in the metal. As a matter of fact, tests on many kinds of materials have shown differences in varying degrees. In recognition of this condition, propel design, for many purposes, places the fiber axis in such a way as to present the direction of maximum strength to the greatest applied stress.

Jan 1, 1931

Develop a full-length-anchored roof bolt that is economical, nontoxic, nonflammable, and non-allergenic. Approach Grout roof bolts with a storable mixture of ultra-fast setting inorganic cement and water. How It Works A loose mixture of dry cement powder, and pinhead-size water droplets encased in waxy globules, are pack-aged in sausage shaped cartridges for storage and use. After the cartridge is inserted Into a drilled hole, the roof bolt is thrust In and rotated to mix the cement and water. The cement hardens in seconds, providing usuable anchoring strengths in minutes. Prior to filling of the sausage shaped cartridges, the microcapsules of water are Intimately mixed with the dry cement. The currently used grouting consists of a mixture of one part water (minimum) with three parts alpha-type gypsum cement and a minor amount of accelerator.

Jan 1, 1978

By Francis S. Kendorski

Caving offers the lowest cost per ton of ally large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently-taken on new importance as deeper, lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface mining methods, and too low grade to support any type of underground mining except a bulk method such as caving.

Jan 6, 1978

By P D. Fraser

This paper examines the new water-hydraulic (hydro powered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef, hard-rock South African mines. These include - drill rigs for flat end tunnel development, narrow inclined raises and winzes, large inclines and declines and long hole based developments such as orepasses and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed air powered, hand-held development are generally more cost effective than imported oil electro-hydraulic drill rigs. Furthermore, hydro powered rigs are inherently energy efficient. The benefits of hydropower are discussed and a æcomprehensive development modelÆ is presented which demonstrates that orebodies can be accessed in significantly shorter times. æLocalisedÆ half level hydropower systems are introduced and a range of ancillary equipment available is listed.CITATION:Fraser, P D, 2012. The use of high-pressure, water-hydraulic (hydropower) technology in South African narrow-reef, hard-rock mines, in Proceedings Narrow Vein Mining 2012 , pp 229-236 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

The techniques used by the State Electricity Commis- sion of Victoria to handle and store brown coal in the both the raw coal and boiler bunkers are outlined. These tech- niques were adopted in agreement with the science of modern bulk solids handling. By successful balance between practical requirements and bulk solid handling system design require- ments the Commission expects to confidently attain reliable coal flow even for the most adverse of coal flow properties. Attainment of this goal demanded full attention to channel detail selection. An outcome of this attention has been the development of a novel bunker and discharge arrangement for handling extremely difficult to handle coals. Due to the novel features of this slot bunker outlet arrangement it's ad- vantages and disadvantages are discussed.

Jan 1, 1987

By John A. Herbst, K. Rajamani

Process improvement is probably the most widespread objective of mineral process plant operators in the late 1980's. An important part of such improvements is dynamic optimization which involves reacting to inevitable plant disturbances in such a way that productivity is maximized at every instant of time. This paper describes the way in which mathematical models can be and have been used in dynamic optimization. Both off-line and on-line model applications are described.

Jan 1, 1989

By L. Hales

Neural networks are a generalized, multivariable non-linear modeling technique that can be used to model mineral processing operations. Neural networks will be described as will their use in modeling column flotation. Optimization of column flotation will be explored and discussed by using the neural network column models.

Jan 1, 1996

By G H. Park, Y J. Jun, J H. Park

The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag, the main system formed in the Ruhrstahl-Heraeus (RH) vacuum degasser, was measured at 1873 K to understand the effect of slag compositions on the carbon contamination in the ultra-low carbon (ULC) steels. The stable form of carbon was demonstrated to be carbonate by plotting the log [(wt%C)/aC] ratio against the log p(O2) which ranged -11 < log p(O2,atm) < -9. The carbon solubility of the CaO-Al2O3-FeO-SiO2-MgO slag can be estimated using thermodynamic model. The distribution ratio of carbon increased with increasing concentration of FeO due to the FeO reduction reaction and increased basicity of slag. The carbonate capacity of the CaO-Al2O3-FeO-SiO2-MgO slag can be expressed as a linear function of the activity of lime and the optical basicity.

Jun 19, 2024

By F. N. Kissell, H. K. Sacks

This study examines the accuracy of area sampling for measuring the dust exposure of mining machine operators in coal mines. The specific objective of this research was to find locations where an area sampler might work better than earlier studies have indicated. The results show that fixed-location area sampling cannot accurately predict the dust exposure of a machine operator, even when the best fixed location is sought, the fixed location is quite close to the operator and the bias due to the dust concentration gradient is corrected. Industrial hygienists have known for many years that area sampling is unsuitable for measuring air contaminant exposures in the workplace. Near contaminant sources, the dilution air and the contaminants are not evenly mixed. Therefore, when workers are near contaminant sources, exposure measurements must be taken from the worker&apos;s breathing zone to be accurate.

Jan 1, 2003

By Charles M. Cooley

With explosives representing over 10 pct of the cost of operating the entire company, the Maumee Collieries Co., Terre Haute, Ind., inaugurated a program to develop a low-cost blasting agent. Results of more than two years&apos; work were announced on May 1 by Hugh B. Lee, president of the company. Utilizing a mixture of commercial-grade ammonium nitrate and carbon black packed in polyethylene bags, Maumee has been able to reduce blasting costs by 50 pct. The lower costs are brought about principally by elimination of high transportation charges on fixed explosives and use of low-cost material (commercial NH,NO, and carbon black). The Akremite blasting method incorporates a 20-lb cap-sensitive primer to detonate the stable explosive. Maumee now uses Akremite exclusively in its stripping operations producing more than 2 million tons of coal per year. The explosive is employed to break about 25 million cu yd of overburden that covers the coal

Jan 5, 1955

By Arthur Tauber, Horst Kedesdy

FERRITES are sintered metallic oxides of the spinel structure type1 and belong to the class of soft ferromagnetic materials. Similar to a ceramic, they can be formed and fired to a dense body, exhibiting a high electrical volume resistivity ranging from 102 to 102 ohm-cm as compared with 10-6 ohmcm for some of the metallic magnetic materials. This high resistivity, with resulting low eddy current losses, finds special application at high frequencies. The dispersive susceptibility of ferrites at microwave frequencies has also led to many applications in this field. Where high resistivity with high permeability is desirable, ferrites are used in low frequency applications. During the last few years ferrites exhibiting rectangular hysteresis loops have been developed for computer and magnetic memory systems. The general formula for ferrites is MeFe2O4 where Me is a divalent metal ion such as Ni, Zn, Mg, Mn, Cu, Cd, and Fe. Only two of these ferrites are nonferromagnetic, namely, those with Zn and Cd. Solid solutions can be formed between different ferrites, and it is of interest to note that solid solutions of a ferromagnetic ferrite with a nonferromagnetic ferrite yield much better magnetic materials than the basic ferrite body. In general, it can be said that the solid solution formation between ferrites has widened the field of ferrite synthesis and has led to methods of preparing materials with a large variety of magnetic properties.

Jan 7, 1957