Search Documents

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By Ian Tolliday

Emulsion Explosives manufacturers are aware of the destabilizing effect that the presence of inorganic impurities such as magnesium and iron and organic impurities such as naphthalene sulfonates and alkyl amines can have on their emulsions. This destabilization often manifests itself as severe crystallization and subsequent product loss. This paper describes the performance testing of specifically developed emulsifiers which give greatly improved emulsion stability in the presence of high levels of impurities. The test work involved a series of stability tests using ammonium nitrate doped with various levels of crystal modifier and anti-caking agent. A further series of tests were done to evaluate the stability using ammonium nitrate doped with various levels of iron and magnesium ions.

Jan 1, 2018

By AIME AIME

AT Williams College, in the quaint old New England town where people still go to the post office for their mail, an interesting institution has come into being as one of the aftermaths of the peace conference at Paris in 1919. The war taught the world many things about economics although much remains to be learned and more to be appreciated. B. M. Baruch, H. A. Garfield, president of Williams, and others who took part in the conference at Paris or in preparation for it, feeling that benefits would accrue from informal friendly discussion of the problems that lead to political differences between peoples, called together a summer conference in 1920. This has now become an annual affair and is coming to be looked upon as an important center for developing and stimulating public opinion. Membership in the Institute is by invitation and the lists change to correspond with the particular subjects taken up. Each year a number of distinguished foreign public men are invited to be the guests of the Institute and to meet men and women from various parts of the United States interested in their special subjects. Round tables, general conferences, and public lectures are the means employed to bring out discussion. The first are organized by groups, each including usually 25 to 40 people interested in a special subject and meeting three times a week for informal discussion. Teachers, writers, economists, engineers, business men, indeed men of all vocations and many shades of opinion, are brought together. Once a week each round table presents in general conference with the members of all other groups the more general conclusions reached in its own decisions. Afternoon and evening lectures are given by the foreign guests and these are open to the public. The lectures and the general conferences are reported widely in the press but the proceedings as a whole are not printed, no resolutions are passed, and no action is taken or contemplated. The whole plan is to furnish a forum for free discussion in hopes that the difficulties of various groups and peoples may be taken up sympathetically and good understanding promoted. There is no creed, doctrine or dogma to which the Institute is committed and widely different views are currently presented. The constant effort is to bring out points of view and the reasons for them rather than to build up convincing arguments favourable to a specific action

Jan 1, 1926

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

WASHINGTON, D. C. HERBERT C. HOOVER, Chairman H: FOSTER BAIN, Vice-chairman DAVID WHITE, Vice-chairman HARVEY S. MUDD, Secretary-Treasurer, Room 2114, Dept. of Interior Bldg. J. F. CALLBREATH HENNEN JENNINGS E. W. PARKER T. T. READ An inspiring meeting of the Washington, D. C., Section was held at the Cafeteria of the Interior Building on Friday evening, Dec. 6, 1918. One-hundred and thirty-five members and guests attended, and Vice-chairman H. Foster Bain presided. The Committee on Nominations reported: for Chairman, Herbert Hoover; for Vice-chairmen, Frederick G. Cottrell, and F. L. Ransome;

Jan 1, 1919

The control of industrial grinding circuits in Australian concentrators has been practised for many years in one form or another. Some have established simple feedback loops in areas such as fine ore bin feeders (tonnage control), mill pump sump levels (flow control) and water additions (density control). There are also some sophisticated systems which infer circuit product size using complex measurements of mass flaws and water additions in the circuit and attempts are made to control those flaws to produce a constant circuit product size. The inferred size method in Australian concentrators has become firmly entrenched in the last ten years and control techniques involving the use of direct size measurements with reliable on-stream sizers have been Ignored.

Jan 1, 1983

By Finn Ouchterlony

INTRODUCTION Much of present fracture toughness testing con¬cerns chevron notched specimens (Newman Jr., 1984) since these, in principle, require neither fatigue precracking nor more registration than failure load to determine fracture toughness. Two such specimens which can be made from diamond drilled rock cores with minimal machining are the Short Rod (Barker, 1977) and the Chevron Edge Notch Round Bar in Bend¬ing or CENRBB Specimen (Ouchterlony, 1980). Even if the precracking property is especially valuable for a material like rock, practice has made the relative advantages of these chevron notched specimens much less apparent (Ouchterlony, 1982; Ouchterlony and Sun, 1983). Enough remains, however, to have the Commission on Testing Methods of the International Society for Rock Mechanics (ISRM) focus on them as standard configurations in a "Suggested Method for Determining Fracture Tough¬ness of Rock Material", which is in preparation. This paper presents material which supports the ISRM effort: 1. An experimental compliance calibration of the Chevron Bend (CENRBB or CB for short) and re¬sulting formulas. 2. Specimen tolerances, evaluation formulas, and loading rate requirements relating to both Short Rod and Chevron Bend Specimens of suggest¬ed standard proportions. 3. Some fracture toughness values obtained with the Chevron Bend Specimen. This material is mainly based on two reports (Ouchterlony, 1984 and 1985). CALIBRATION OF THE CHEVRON BEND SPECIMEN Preliminaries The specimen and basic notation is shown in Figure 1 together with a straight notched variety (SECRBB). Subscripts c and s are sometimes used below to distinguish between them. Assuming linearly elastic conditions the load point compliance [ ]

Jan 1, 1986

By Paul Clifford

The Florida Institute of Phosphate Research (FIPR) is an independent, state of Florida research agency. It was created in 1978 to conduct research to enhance the competitiveness of the Florida phosphate industry. The institute also conducts research to prevent, minimize or rectify environmental impacts caused by the industry. And it helps educate the public concerning phosphate-related technology and issues. FIPR is funded by a severance tax on the industry and is governed by a five-member board of directors appointed by the governor. FIPR's research is playing a role in enhancing the competitiveness of the Florida phosphate industry. Its technology research program seeks to improve surface mining and pipeline transportation while reducing the energy cost for pumping phosphate matrix. It is developing new and improved methods of beneficiation and fertilizer production. This includes new process flowsheets and on-line analyzers and process control methods. FIPR is also developing uses for the phosphogypsum byproduct of phosphoric acid production and evaluating the risks associated with its uses.

Jan 1, 1998

By P. Goosen

The paper presents a basic summary of the approach to hydraulic scale-model tests as may typically be applicable to slurry flow situations. A case study is presented illustrating how hydraulic scale-model tests can be of significant benefit in evaluating the performance of novel or unproven slurry handling equipment. In this case the equipment tested was a fan-shaped expansion piece used to spread the discharge from a launder over the full width of a dewatering screen. The tests showed that the device did indeed distribute the slurry flow both in terms of volume and solids mass, but not perfectly uniformly. Unfortunately the equipment was not taken beyond the model test phase. The scale-model test approach did, however, prove to be very useful as it is considered to have provided a good indication of the expected performance of the full-size unit. Significantly, this was achieved at very low cost compared to the cost of installing the device into the proposed plant and having to later change it out for an alternative or live with the less than optimal performance. The paper illustrates the value that can derive from applying hydraulic scale-model testing techniques to evaluating the performance of new or unusual slurry handling equipment. There is particular value in situations that do not lend themselves to numerical modelling.

Jan 1, 2007

By Gemuts I, Hudson D. R

Massive sulphide mineralisation at the Miriam prospect, near Coolgardie, Western Australia, is fracture-controlled and associated with disseminated sulphides near the basal contact of an ultramafic lens. The lens is peridotitic in composition with a pyroxenitic zone at its base, and lies within a sequence of altered high-Mg basalts and pillowed tholeiitic basalts. Recrystallisation of the ultramafic rock has resulted in the development of secondary olivine. The average composition of the sulphide fraction of massive ore is Cu = 4.4%, Co = 0.3%, Ni = 23.0%, Fe = 31.8%, S = 40.6%, consisting of the supergene assemblage violarite-pyrite to a depth of 210 m.

Jan 1, 1973

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By Howard M. Cotton

Early in 1977, Amoco Production Company and Houston Chemicals, a subsidiary of Pittsburg Plate Glass (PPG) Industries, started producing iodine commercially in northwestern Oklahoma. This is significant because it is the first plant in over 40 years to be built in the United States with iodine as its sole commercial product. With the exception of a limited amount of iodine produced by Dow Chemical in Michigan, the United States is dependent upon imports from Chile and Japan for its iodine needs. The two million pounds of iodine produced annually from the Woodward plant will supply over one-third of the United States' requirements. Routine analysis of subsurface brines by the Formation Water Lab at the Amoco Production Company Research Center in Tulsa, Oklahoma, revealed unusually high concentrations of certain potentially economic minerals. Investigations determined that, of the minerals in question, iodine appeared to offer the best potential. The brines in question are located in the Morrow sands (basal Pennsylvanian) at a depth of 7,175 to 7.400 feet, in an area where Amoco has been active in a gas play for the past 20 years. The regional iodine concentration ranges from 10 to 700 ppm and averages around 300 ppm with the project area. The project is located 8 miles north and slightly east of the town of Woodward, where the well-developed, porous, and permeable sands of the Woodward trench contain large volumes of brine.

Jan 1, 1978

By Ishikawa K, Kikuchi T, Tokairin Y

Roadheader, developed from coal cutting machines, is generally classified as a tunnel excavation machine for soft rocks in respect to excavation mechanism, machine structure, weight, engine output and so on. In recent tunnel works, however, there is an increasing demand for changing from blasting to mechanical excavation by roadheaders to avoid environmental problems such as noise and vibration. But there exist various difficulties in excavation of harder rocks by roadheaders. In order to explore the possibilities of roadheader excavation, we performed field and laboratory experiments. In the field experiment, roadheader model S-125 (Mitui Miike Machinery Co.,Ltd.) was tested for various rocks of wide range of hardness, and excavation capacity and wear of picks were measured. In the laboratory test, cutting performance of the picks was tested by our cutter testing machine. This report describes thr: of these experiments and discussions :n possibility of applying boom-type tunnelling machines to hard rock excavation based on these experimental data.

Jan 1, 1987

By E. Dermietzel

The fundamental ideas of Computer Aided Lignite Mining (CALM) with respect to hardware and software used at Rheinbraun are explained and outlined in detail. The computers used in the main data processing department and in the different departments in the mines are described. Special emphasis is laid upon the network connecting the computers at different places for data-exchange. Concerning technical applications, the main facilities of CALM are deposit and pit modelling, complex geomechanic computations and mass calculations, data recording from the production process in the pits and refining plants, and detailed information and planning systems for water management and mining equipment. Concerning administrative applications, the main facilities of the software are the accounting system with cost controlling and planning, the materials management system with stock control, forward planning and computer supported order procesing, a system for the administration of property within and surrounding the mines, and systems for personnel administration and payroll. The various software systems developed for these application and the influence of data processing technique, such as data base management and the interconnection of data processing systems, are demonstrated.

Jan 1, 1987

By J. H. Dewey, J. McCreedy

Ontario Division of The International Nickel Company of Canada, Limited, operates five under- ground mines and one open pit on the rim of the Sudbury basin. In 1962, the total underground ore production was over 10 million tons which was mined mainly by blasthole and caving methods with the remainder by cut-and-fill, square set and undercut-and-fill techniques. Because of the large expenditures required annually for explosives, a great deal of study has been devoted toward cost reduction in this field. The large saving effected by ammonium nitrate-fuel oil combination at the open pits, along with reports of its success in underground mining in Sweden, generated much interest in the possibility of its use as a replacement for high explosives in the underground operations at Inco. In June, 1960, a research engineer was assigned to this project, and preliminary investigations soon indicated substantial savings and important safety advantages. The final results of the program were successful beyond any expectations and ANFO is now used exclusively in all Inco mining operations in Ontario except shaft sinking.

Jan 11, 1964

By R Loweth

The application of discreet event simulation has matured in modelling manufacturing systems for production analysis. This simulation tool was used in studying a number of mining operations, especially material handling processes. The study of truck-shovel operation including equipment matching, selection, and production estimation utilised the discrete event simulation for providing valuable decision-making information. The sophistication of the available simulation tools grew over times, and simulation driven animation was used to facilitate the validation and visualisation of the simulated system. This form of visualisation enhanced the simulation use greatly. First of all, it provided a communication medium to transfer information to the non-technical managerial personnel as a better decision-making tool. Moreover, the animated visualisation provided a validation tool to check the working of the simulated system and interaction among its components.

Jan 1, 2003

By Samuel Lasky

FAULTING at Kennecott, with its attendant fracturing, is unusual, complex, and important. As study. and knowledge of the various fault systems have progressed, appreciation of that importance has helped in the selection of proper horizons for exploration and in the avoidance of useless crosscutting and drifting. During the study of this faulting and fracturing, a suggestion concerning the formation of the ore-bearing fissures occurred to me. Further study in the available portions of the approximately 45 miles of workings in the Kennecott mines for the purpose of checking up the the suggestion led to the hypothesis which this paper will attempt to present. Briefly, the hypothesis may be stated as follows: The formation of transverse faults that stop against a main, system is connected with changes in the strike or dip of the main fault, and such cross faults or fractures lie in the moving block of the main fault system and indicate a change in strike or dip of the main fault. It has been found that each kind of change tends to produce definite effects and that careful study of the evidence can often suggest the exact type of change.

Jan 1, 1928

Jan 1, 1901

By Sukune Takenouchi

Porphyry copper deposits in the southwestern Pacific region differ in some points of geologic features from those of the United States. The deposits distribute along old or active island arcs and are generally younger in age (1-16 m.y. B.P.). In Japan, however, no typical porphyry copper deposits are yet reported, though the geological situation of Japanese islands is similar to that of the southwestern Pacific. Fluid inclusions in some porphyry copper deposits In the southwestern Pacific region and those in igneous rocks genetically related to the ore deposits In Japan have been studied, and the genesis of ore-forming fluids from igneous rocks are discussed. From the results, the possibility of finding porphyry copper-type mineralization in Japan are considered.

Jan 1, 1976