Search Documents

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

The pyroclastic-filled Voorspoed kimberlite pipe has a low grade due to significant internal dilution which translates to a marginal business case. The site, with excavations, tailings dumps and buildings remnant of mining from 1906 to 1912 is to become De BeersÆ benchmark mine in South Africa. In a climate of skills shortages and lean structures, a geological service to optimise exploitation of this complex resource was established. As historical mining removed the higher-grade centre of the pipe, initial production was in the weathered upper benches along brecciated pipe margins. Trenching and blasthole logging before blasts helped to mitigate the effects of the drastic contact deviations that occur when working with an inferred geological model. However, identification of unfamiliar weathered kimberlite and delineation of unmodelled internal waste posed challenges. Efficient grade control by demarcation and allocation of individual truck loads will be vital to continue profitable mining at Voorspoed. Further challenges arose across disciplines. The first yearÆs planned production of mostly weathered kimberlite was processed through a plant designed for VoorspoedÆs unusually competent ore. The high clay content of the weathered material led to clogged chutes and overloaded fines disposal, hampering efforts to commission the plant. Resolving this problem involved mining æout of planÆ to provide a blend of fresh and weathered kimberlite. The calculation of an accurate mine call factor was hindered by a lack of haul truck monitoring, process stoppages and stockpiling in the plant during commissioning. Updating of the geological model to incorporate the contact changes observed in the pit was slowed by the need to first understand how 40 years of exploration data was integrated to create the model. A plan, involving focused mine geology practices, is in place to upgrade a portion of the resource from Inferred to Indicated level of confidence. These challenges are not limited to new mines but will be ongoing as new information is constantly gained at Voorspoed and many mining operations.

Jan 1, 2009

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By R. M. Brick

The etched mierostructures of cold-worked alpha brasses, after reductions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonymously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {ill), in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans' results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson6 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into symmetry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By Murray Weintraub

The Bureau of Mines investigated the aerodynamic factors that control the functioning of the blowcase devices used in pneumatic processes for dispersing solids. Alumina powder of 8-micron mass-mean diameter was placed in 0.75- inch-diameter by 10-inch-long cylinders} and a blowcase technique was employed. It was determined that dimensions and gas rates for discharging the powder from the cylinder by a stream of gas may be calculated by assuming a fluidization mechanism and extrapolating residues to a desired finite quantity or to zero at the terminal velocity. The state of agglomeration of a powder at discharge may be determined from measurements of the velocity required for zero residue.

Jan 1, 1967

By S. S. B Wang

Zirconia-based ceramic materials have potential applications in high temperature furnace insulation, hot extrusion and casting dies, pressure nozzles, cutting tools, engine parts and electronic materials. High purity and superfine powders of zirconium oxide (baddelyte) were synthesized from a solution containing zirconium oxychloride and urea under hydrothermal conditions. crystallization of the metastable tetragonal zirconia using magnesium oxide or yttrium oxide as stabilizing agents was successfully achieved. The mechanism of hydrothermal reaction to produce these powders are discussed.

Jan 1, 1989

By Kr. J. Dedelyanova

Selective flocculation of iron minerals could improve the economics of high intensity magnetic separation as concomitant process. When the minerals are finely disseminated is necessary a finer grinding to be applied which generates a lot of slimes. The HIMS is not enough efficient for particles below 20 microns ? territory where the selective flocculation is already well known industrial practice, so the combination of these two methods of beneficiation can bring a higher grade at high recovery to be achieved. The dynamics and selectivity of the precipitation process is studied in batch tests with flocculant starch and dispersants sodium silicate and sodium hexametaphosphate. The influence of preliminary conditioning with nitrogen acid at pH 2 before flocculation is also investigated. Flowsheet including these two methods is tested and the distribution of iron is shown.

Jan 1, 2014

By Sergio N. Monteiro, Artur C. Pereira, Foluke S. Assis, Henry A. Colorado

The fique fiber is an important natural fiber, originally from Colombia where it is used for sacks and crafts while its plant is used to contain slopes. However, few studies were realized with the fiber obtained from the fique plant leaf, its mechanical properties are superior in many aspects in comparison to some other lignocellulosic fibers. This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of a fabric made of fique fiber by means of Charpy impact tests. It was found that the addition of fique fabric results in a marked increase in the absorbed energy by the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that transversal rupture through the fique fabric interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Mar 1, 2017

By R. Jedrzejczak

Endako Mine is an open pit molybdenum mine located in the north central region of British Columbia, Canada, approximately 160 km. west of Prince George. Production for the latter part of 1992 is expected to average at 63,500 tonnes per day of which 27,000 tpd constitute the mill feed. This production is achieved with five 15 to 19 cu. yd. electric shovels, six Euclid R190 and two Unit Rig M120 diesel-electric haul trucks, and three 121;.1 inch electric rotary drills. There are three ore zones delineated into pit areas called the Endako, Denak East and Denak West. Present mill feed source is the South East stage of the Endako Pit while the stripping is carried out in the South Wall stage also of the Endako Pit. The mine high grade aggregate is reduced in the primary and secondary crushing circuits before processing in conventional RM/BM/flotation circuits. The majority of the Molybdenum Sulphide (MoS2) is roasted on site to produce technical grade Molybdenum Oxide (MoO3) while a portion is further refined and treated to yield a 99.9% pure Molybdenum Sulphide (MoS2) "Ultrapure" product.

Jan 1, 1993

By J. E. Brownhill

This paper does not deal with the typical start-up issues of equipment, production capacity or work force. This is a description of the challenges faced and the changes made by the project team to bring to fruition the reconstruction of Port Inland. Many honored traditions and norms had to be overturned to find the winning combination that provided the productivity, flexibility and cost necessary to survive in today's competitive minerals environment. This paper covers the innovation in terms of machinery, operations, and management philosophy that permitted the renovation and reopening of Port Inland as a commercial limestone producer in the spring of 1992. Port Inland, constructed by Inland Steel in 1930, operated as a captive source of metallurgical grade limestone for the steel industry until its closure in 1989. Located in the Upper Peninsula of Michigan on the north edge of Lake Michigan, the operations consist of a deep water port facility with crushing, screening and stockpile storage for 500,000 tons of finished product at the port. Ninety-nine percent of the stone is shipped via lake boat to ports within the Great Lakes. The operation is unique in that both metallurgical Dolomite and Limestone are produced on site. In 1930, Port Inland was at the fore front of technological advancement. It was the first major mining operation to use roller bearings and other equipment innovations. Over the 60 years of operation, Inland Steel placed emphasis on steel making technology and iron ore mining at the detriment of the limestone operation. By the early 80's, Port Inland was no longer a leading competitor. Inland Steel, unable or unwilling to spend the capital to modernize, closed the facility in the fall of 1989.

Jan 1, 1994

By R. A. Hemstock

"OIL EXPLORATION in Western Canada has produced outstanding results in the past few years. From such successes as Leduc and Redwater on the western plains, oilmen are now moving north in the ever-widening search for oil. They are reaching new frontiers and meeting new problems presented by this vast hinterland.One of the least known but most troublesome phenomena which will be encountered is permafrost. This term relates to a thickness of soil or other superficial deposit, or even of bed-rock at variable depths beneath the surface, in which a temperature below freezing has continually existed .for a long time. This permanently frozen ground affects, in many ways, oil exploration and exploitation. Seismic records are changed, pipe lines cannot easily be ditched into the ground, formation of wax is speeded-up in tubing and pipe lines, roads are difficult to build, and foundations of buildings and even of drilling 'rigs may require entirely new methods of construction.Permafrost underlies roughly one-fifth of the entire 'land surface of the world. It covers the northerly portions of Eurasia and North America. In the area that we are here concerned with, the southern boundary of permafrost extends south of east from about latitude 59°N. on the Pacific coast across the Rocky mountains, through Great Slave and Athabasca lakes, to cape Henrietta Maria, at the junction of Hudson bay and James bay (see Figure 1). Geologists generally agree that permafrost first appeared in the Pleistocene or Ice Age as the result of abnormal ground freezing."

Jan 1, 1952

By Peter Grawenhof

Universal joint shafts and slipper spindles are commonly used in rolling mills to compensate the design- and process-related offset between the motors and work rolls. Although both types of shafts exhibit on the same kinematic principle, there are basic differences regarding the design concepts. These differences become noticeable on many levels and may become very distinct in terms of Life-Cycle-Costs (LCC). In this respect, a critical comparison between universal joint shafts and slipper spindles can be made.

Aug 16, 2017

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

By Morris Muskat

Analytical calculations have been carried out on the effect of casing perforations on the productivity of wells, and formulas have been derived for general types of perforation patterns. The numerical calculations, however, show that the resultant well productivity is essentially independent of the perforation pattern, but is determined mainly by the total perforation density. Thus, for example, for a density of three perforations per foot of casing, the well productivity will be cut to one third of that of the uncased well for a perforation radius of 1/8 in., and to approximately one half for a perforation radius of 1/4 in., regardless of the detailed manner in which the perforations are distributed over the casing surface. The analytical theory is also extended to include wells completed with slotted liners. It is shown that the reduction in productivity due to such liners will be relatively small as compared with that due to perforated casings. The increasingly important role being played by productivity factors of wells in determining well potentials and in the general evaluation of producing formations lends interest to the analysis of all the various factors that may infuence the productivity of a well. In recent papers1 the results have been given of theoretical studies made to determine the effect on the productivity factor of a well of the gas-oil ratio of the production and the connate water within the sand. These have served to show that both of these factors may, under suitable conditions, materially reduce the effective productivity factors below those that would be anticipated on the assumption that the wells produce homogeneous fluids. In this paper will be presented the results of the analysis of an entirely different factor influencing the productivity of a well. This refers to that resulting from the increased use of the method of completing wells by setting casing opposite all of the productive strata and then gun-perforating the particular zones of immediate interest. The practical success of this method of completion would appear to be an answer to the question as to whether it seriously reduces the well productivity or materially cuts down the ultimate oil recovery that may be derived from the producing section. Nevertheless, it is of interest to examine just how great the effect of the restricted flow channels, represented by the gun perforations, may be in increasing the over-all effective sand resistance. Of course, to the extent that the well potentials are severely restricted by proration regulations, minor reductions in well productivities are even less serious than if the wells were to be allowed to produce wide open. On the other hand, even under these circumstances there may be at least the academic interest in such calculations in being able to correct and evaluate the effect of the perforations in order to carry

Jan 1, 1943

By N. S. Greensfelder

The firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 1/24000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the developmcnt of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovcrcd by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silvel spoon downward, without the least force upward.'ll This fallacious belief that explosives act downwards only is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of mercury fulminate for use in detonators are the simplicity of exploding it and the great shock developed by its explosion.

Jan 1, 1923

By Frederick G. Tickell

Petroleum engineers are displaying considerable interest in those fundamental properties of matter and energy that control the phenomena of oil and gas production. The subject is a difficult one to investigate by laboratory experiments for two reasons: (1) it is impossible to reproduce in the laboratory the scale of forces and dimensions that exist in the underground reservoir; (2) if we attempt to scale down the dimensions we are unable to reduce all proportionally. It is as if we tried to construct a model blast furnace for the reduction of iron ore, and reduced all lineal dimensions. We should find that the interstices between the miniature chunks of ore would not permit rapid transfer of gases, that combustion and heat transfer would not take place as in the full size furnace and that, in short, the contraption would not work. Just so, when we attempt to make a reduced scale oil field we find we must have, not only miniature reservoir and miniature wells, but "miniature" sand, 011, gas, etc. Much valuable work, however, has been done along these experimental lines and more will no doubt follow, but investigators should bear this point in mind and strive to attain dimensional homogeneity and dynamical similarity in order that their conclusions may be translated into terms applying to the oil reservoir. As Gibson says,' "These conditions are attained when all terms of the physical equation have the same dimensions, . . . when all corresponding particles of the two systems trace out similar paths and when the velocities are such as to make all corresponding forces acting on two such particles in the same ratio." It is the purpose of this paper to discuss the mechanics of fluid movement as it pertains to the oil pool and to point out the complexity of the laws of fluid delivery under the conditions often found. We have to do, fundamentally, with confined fluids, possessing potential energy whose expenditure is restricted by certain properties of the confining media and of the fluids themselves. The equation of motion and time is completely stated when we can assign values to the propulsive

Jan 1, 1929