Search Documents

By T. T. Chen, P. Pint

Based on the mineralogy, phase characteristics and compositions of the smelter feed, the smelter products and the smelter wastes, the sources and distributions of mercury and arsenic in the Afton copper smelter, Kamloops, British Columbia have been determined. Of the total mercury In the feed, approximately 33% is in solid solution in tennantite, 51% is in native copper and 16% occurs as mercurian silver. Arsenic in the feed occurs mainly as tennantite. Under current smelting conditions, 99.6% of the total mercury In the feeds enters the off-gas cleaning system. From this off-gas, about 1% of the total mercury, occurring as dust, is recirculated to the flotation concentrate; 4.6% of the total mercury is contained in SO2 scrubber sludge which is discharged to tailings. Approximately 78% of the total arsenic in the smelter reports in the copper products; 20% is incorporated in the dust and slag which are subsequently recirculated to the mill. Only 1.8% is rejected as scrubber sludge, and less than 0.2% 1s released to the mercury scrubber.

Jan 1, 1984

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

The use of roof bolting gave promise of substantial economic benefits to Continuous Miner operations at Michel Colliery. As the first step in the adoption of bolting, 142 anchorage tests, employing six types of anchor shells, were made in three mines. Significant differences were found in the anchorage capabilities of the various shells and the various roof rocks. Introduction S PORADIC attempts at roof bolting had been made at Michel Colliery over a period of ten years. Results were indifferent or inconclusive. A concerted effort was not made, because a compelling need for bolting did not exist. By 1962, however, the advent of Continuous Miners had brought a new significance to roof bolting and, at the same time, the increasing price and scarcity of mine timber made bolting materials more competitive in cost. A fresh appraisal of bolting, therefore, became justified and necessary. The potential benefits of roof bolting at Michel are several.

Jan 1, 1963

By D. E. Hilts, R. P. Miller

A large coal-fired power plant is to be built jointly by Pacific Power & Light Co. of Portland, Ore., and by The Washington Water Power Co. of Spokane, Wash., at a site about six miles northeast of Centralia, Wash. (Fig. 1 inset). Coal will be mined from nearby open-pit strip mines that will require cut slopes up to 250 ft in height. Coal will be removed from a seam approximately 50 ft thick, located at the bottom of the mine slopes. The coal fields are located in a geologically complex area that has been subjected to intense folding and faulting. As a result, the soils and rock comprising the overburden are highly fractured, jointed, and faulted. Classical approaches to slope stability based solely on the physical proper- ties of the overburden appeared to offer little assurance that theoretically stable slopes would remain stable. Further, the scope of the exploration program that would be required to provide a reasonable evaluation of the primary and secondary structural features from which a statistical evaluation could be developed was considered impractical. As part of the development of an overall mining plan, an experimental Pilot mine excavation, about 225 ft high and about 400 ft long at the base, was made within the coal field. This experimental cut was to provide firsthand knowledge of cut slope behavior. Our purpose at the Pilot mine was to observe the cut slopes as the excavation proceeded. To accomplish this purpose, the highwall of the experimental cut was instrumented to measure face movements and movement at depth behind the face. In addition, a detailed geologic map of the soil and rock conditions exposed in the highwall was prepared, and continual visual observations of the mine were made, noting significant events as they occurred.

Jan 1, 1970

By L. Béjar-Gómez

The aim of this research work is to study and characterize the precipitates in structural microalloyed steel by transmission electron microscopy and analysis by low resolution. Microalloyed steel with niobium was produced by casting in an electrical induction oven of 25 Kg capacity. Carbon content in steel was less than 0.1 % and 0.036% of niobium. Steel was processed thermomechanically; reheated to 1250 °C and hot rolled on a laboratory mill to a 13.0 mm thick plate with a finish rolling temperature of 900ºC and a thickness reduction of 80% . This work shows what precipitates are present in steel, the type of precipitates and their morphology. Analysis by transmission electron microscopy of low resolution was applied to obtain the chemical analysis of precipitates and the matrix. Spectroscopy of dispersive energy (STEM - EDS) was applied to obtain the element profile of precipitates. Particles of precipitates of NbC were found; with cubic morphology and size from 70 to 130 nm, circular morphology and size from 10 to 70 nm, polygonal morphology and size from 10 to 80 nm.

Jan 1, 2006

By Baptiste Laubie

Agromining is a phytotechnology aiming at producing commercial metal compounds from low-grade ores thanks to hyperaccumulating plants. The fern Dichranopteris dichotoma is a rare earth element (REE) hyperaccumulator, which naturally grows on former mine tailings in China. It accumulates up to 0.35% of REEs in its aerial parts. Different hydrometallurgical processes are currently developed to recover these elements directly from the biomass or from ashes after combustion. The process presented here consists of a direct extraction by EDTA solution, followed by precipitation with acid oxalic. Optimal precipitation pH and influence of organic matter are determined by modelling and by experimental studies. The final solid contains 4.3% of REEs, with calcium as the main cationic impurity (0.45% of the precipitate). The recovery yield is similar for major REEs and is around 70%. After optimization, upscaling of the process will allow the agromining development to recover REEs from secondary resources with more environmentally friendly techniques.

By F. W. Brackebusch

Paste is a high density mixture of water and fine solid particles with a relatively low water content (10-25%) such that the mixture has a consistency as measured by the ASTM slump cone test from slightly greater than zero up to nearly 12 inches (305mm). Particles of different size classes will not segregate or settle when the paste is not being agitated or when it is stationary in a pipeline. Cement may be a component of paste. Larger particles of aggregate can generally be added to a paste without greatly changing the pipeline transport characteristics. A paste may bleed water slightly when it is allowed to be motionless for periods of up to several hours, but the solids do not become so dense that the paste cannot be easily re-fluidized. The dividing line between the definition of a high density slurry and a paste is not sharp. It is a practical matter that must be considered when designing a pipeline transportation system. If the pipeline is very short, there is very little risk of plugging the pipeline with a high density slurry when flow is stopped for short time periods. With longer pipelines the mixture must remain stable without motion for periods as long as several hours to avoid pipeline plugging. The fine particles in a paste mixture can be composed of mine tailings or naturally-occurring clays, silts and fine sands. The mineralogy of the particles thus can have a wide variety from quartz and feldspar to clays, micas and even salts.

Jan 1, 1993

By Pekka Taskinen, Hannu Johto

"Copper sulfide concentrates often contain impurities such as lead and iron. The phase stabilities of the sulfide impurity systems in metallurgical process conditions are in many cases unsatisfactorily known. Thermodynamic information of a system gives better understanding of its behavior of metal making processes, but also has effects on the economic and environmental factors of the production process. In this study, isothermal equilibrium and quenching experiments of the stable phases of the system Cu2S-FeS-PbS at 700 and 900 °C were carried out and based on the experimental results, Gibbs triangle of equilibrium phases of the system was outlined.IntroductionThe knowledge of stabilities of phases and the thermodynamic properties of many sulfide systems in the temperature range of 500-1200 °C are quite limited. Especially, the knowledge of liquidus surfaces of multicomponent sulfide systems is essential for making many metallurgical processes more environmental friendly and allowing the utilization of complex concentrates. In this work, the aim was to investigate the phase stabilities of the quasiternary system CU2SFeS- PbS using evacuated silica ampoules. Of greatest interest were the properties of the liquidus surface in the system, in order to be able to predict better the formation of a liquid phase in metallurgical processes."

Jan 1, 2012

By F. Cherpereel, R. Gabillard, J. P. Dubus

We present an electromagnetic method taken from the well known radiogoniometer that allows us to locate at the surface of the ground the vertical axis of a magnetic antenna transmitter buried at a depth h in the earth. The method and the equipment achieved are called R. E. P. E. (Relevé Electromagnétique de Points Enterrés). They are daily used to accurately survey old quarries by using triangulation instruments at the surface of the earth rather than in galeries where the setting difficulties considerably reduce their accuracy and increase the work length. The results of several surveys allow us to give the optimum working conditions of the instruments and show that, when the transmitter is at a 20 meters depth, its position is known at the surface with an error lower than 1 centimeter. The power transmitter is of about 8 watts and we can find its location with an error smaller than 1 meter when buried at a depth of about 100 meters. This equipment may be successfully used for location of subsurface miners. The space surrounding the transmitter must then be free from ferromagnetic bodies.

Jan 1, 1973

In line with mining operations throughout Australia, Western Mining Corporation Limiter' is striving to increase productivity by intro-ducing mechanized mining techniques wherever possible. Kambalda Nickel Operations' (K.N.O.) largest operating nickel mine, Long Shaft, is currently introducing mechanized cut and fill methods which must provide flexibility to cater for an orebody that variesconsiderably in width, both along the strike and up dip.This has resulted in modifications to the previous approach to primary level develop-ment, and intermediate stope development, and in the type of development and production equipment being employed. Electric-hydraulic diesel jumbos and diesel loaders have now been mated with conventional rail equipment and production airtrack machines are being utilized.The transition to mechanized methods is in its preliminary phase and is being monitored closely to ensure any productivity gains are not offset by a substantial drop in mine grade. The precise method ofmechanized mining has not been finalized and selective methods will be used, according to the ore width and ground conditions, which vary throughout the mine.

Jan 1, 1985

By Takeo Ueda, Masashi Nakano

We have developed a new blasting system remotely controlled by an electromagnetic firing method, which has proved advantageously applicable to sites where rapid tidal current or deep water may cause serious troubles in underwater blasting operation by a conventional method.

Jan 1, 1983

Jan 1, 1953

By Radford B. Langston

Mining Methods Majority of Production Ramp and Fill at Stillwater, Sub-level Becoming More Important Production at East Boulder from Sub-level l Majority JM REEF ROCK TYPES NORITE - plagioclase and bronzite cumulate GABBRONORITE - plagioclase, augite, and bronzite cumulate TROCTOLITE - plagioclase and olivine cumulate ANORTHOSITE - plagioclase cumulate PERIDOTITE - olivine cumulate

May 1, 2002

By Joel Anderson

Allvac 718Plus is a newly developed superalloy with a good potential for use in fabricated aircraft engine structures when service temperatures exceed 650°C; the limit for standard alloy 718. Fabrication involves welding, where cracking usually is a prohibitive factor. Comparison of the solidification cracking behavior between these two alloys was made by Transvarestraint testing. It was shown that the total amount of cracking was significantly lower for 718Plus alloy, which was associated with a lower amount of ?/Laves or ?/NbC eutectic-type constituents. This in turn is believed to be due to the lower iron content of the Allvac 718Plus material. The analysis of alloying element segregation both within primary dendrite and interdendritic constituents clearly indicates that the segregation of Nb is the controlling factor in determining the final solidification microstructure in these alloys. The Nb concentrations of these constituents are significantly higher compared to the bulk alloy concentration. This was confirmed by the SEM-EDS analysis and calculations assessed with JMatPro, the latter also indicated that alloy 718 is more prone to form Laves and NbC eutectic-type constituents compared to Allvac 718Plus material.

Jan 1, 2008

By Christopher J. Bise

Introduction In August 1977, the federal Surface Mining Control and Reclamation Act was signed into law. It stated that: "The Congress finds and declares that because of the diversity in terrain . . . and other physical conditions in areas subject to mining operations, the primary governmental responsibility for developing. authorizing, issuing, and enforcing regulations for surface mining and reclamation operations subject to the Act should rest with the States." Section 516 of Title V (Control of the Environmental Impacts of Surface Coal Mining) of the Act deals with the surface effects of underground coal mining operations. "Each permit issued under any approved State or Federal program pursuant to this Act and relating to underground coal mining shall require the operator to adopt measures consistent with known technology in order to prevent subsidence. causing material damage, to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner: Provided, that nothing in this subsection shall be construed to prohibit the standard method of room and pillar mining." This section raises many questions. Precisely what is the "reasonably foreseeable" future as far as land use is concerned? And what is the "standard method of room and pillar mining"? The first part of the paragraph seems to rule out longwall mining, but isn't longwalling a "predictable" manner of "planned subsidence"? Does the Act take into account variations among mining methods in differing regions or coal seams? With these questions and the need to comply with the Act's provisions in mind, many states may turn to the Pennsylvania Bituminous Mine Subsidence Act of 1966- the only comprehensive subsidence act passed by any state-as a model for their own programs. Thus, it is very important to evaluate Pennsylvania's Act to see whether its basic assumptions can accommodate national application. This paper will note the Subsidence Act's provisions and guidelines, briefly analyze the current state-of-the-art in subsidence damage prevention and control, and list several recommendations for altering the Act's application guidelines for different mining areas.

Jan 1, 1982

By V. F. Hollister

Computer programs developed as part of the PROSPECTOR project at SRI International can indicate where the highest grade hypogene copper occurs in porphyry copper prospects. The programs are useful in selecting drilling targets in untested porphyry deposits. Because of mineralogic, structural and lithologic variations in porphyry-type deposits, three distinct computer programs have been constructed; however, this paper considers only the stockwork type in homogeneous rock (similar to the Lowell and Guilbert model). The programs represent models in the form of inference networks that utilize the mineralogic, alteration, lithologic, structural, geochemical and geophysical data normally collected prior to a drilling decision. One example of an application of the PROSPECTOR program for a stockwork-homogeneous porphyry is given: Island Cooper in British Columbia. Computations based on the surface geologic, geochemical and geophysical data for Island Copper clearly disclose the best hypogene grade of the deposit. Other deposits were tested in the programs as well, and in each case PROSPECTOR programs indicate the region with the highest hypogene grade.

Jan 1, 1983

By José Aloisio Paione, Eudes Prado Lopes

The geophysical exploration carried out by the Brazilian government through the Mineral Resources Development Co. (CPRM) to discover and develop Brazil's mineral resources is discussed. Particular mention is made of procedures specially adapted for contracting companies specialized in geophysics, CPRM's activities, statistical data from study programs, as well as the financial investments committed. More than 500 000 km of aerogeophysical surveys have been carried out by CPRM in the last four years, and it is expected that more than 600 000 km will be flown in 1974 and 1975, at an investment of approximately $30 million.

Jan 1, 1977

By Sayantan Chakraborty, Kaushik Dey, SaKaushik Dey tyabrata Behera

Drilling and blasting is a popular excavation technique in the drift of underground mine. Faster completion of drift reduces the gestation period and thus longer blast pulls are attempted with longer drill holes. This compels the blasters to initiate higher charge quantity with higher confinements and ultimately results into blast-induced cracks beyond the desired periphery line of excavation. Assessment of the extent of these crack networks is difficult and often neglected. Near-field ground vibration models are often used as damage predictors (Dey, 2007, Yang et.al 1993, Holmberg et. Al 1979) but not necessarily deals with the positions of the cracks. Qualitative measurement of actual damage extent often measured using some geophysical tools, namely, P-wave velocity (Tezuka, 1995), seismic imaging (Dey, 2011), bore hole pressure monitoring (Brent and Smith, 1996), electrical resistivity (Grady and Kipp, 1993), GPR (Adams et.al, 1993) etc. Ground Penetrating Radar (GPR) is a similar geo-physical tool, which uses Electro-magnetic (EM) pulse for characterizing the medium. Similar to other geo-physical tools, GPR also comprises of a transmitter and one/multiple receivers to generate the EM pulse and receive the same after reflection/refraction from the medium(s) respectively. After its development in 1970s, GPR gained increased popularity due to its application in many important fields, namely, identification of buried objects, geological characterization, identification of geological disturbances etc. Thus, it is felt that GPR technique can be used to detect the invisible cracks inside the rockmass from the rock surface (wall and roof) itself. Understanding the same, field experimentations are carried out in an underground manganese mine in Central India, which operates on the ‘cut and fill’ method of mining at a depth of around 300m from the surface. Wedge cut blasting is carried out in the horizontal drifts of the mine using suitable blast design. A 1.6 GHz antenna was used for the GPR scanning, in which GPR transmitter transmits signals predominantly of the said frequencies. The signals get reflected back from any type of interfaces between materials in the target area, with different dielectric properties and is received by the receiver part of the ‘trans-receiver’ antenna and memorized in the Data Acquisition Unit (DAU). The data acquired is processed using a software. Ground vibration monitoring of the blasts are also carried out to develop a vibration predictor. The numerical analysis of near-field vibration predictor model results into the estimated vibration levels at the point of identified cracks. Introduction

Jan 1, 2019

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

The Department of Homeland Security (DHS) has undertaken a probabilistic risk assessment (PRA) approach to quantifying the infrequent, yet high-impact explosive terrorist attacks on the United States (US) homeland and aiding in mitigating that risk through efforts ranging from intelligence gathering, defense postures, detection architectures, partnering with industry to prevent acquisition, and informed medical response. Based on an evaluation of existing model options, a path to the realization of an exterior explosive model (EEM) that builds upon existing models while meeting runtime requirements, maintains consistency with existing DHS chemical, biological, radiological, and nuclear (CBRN) consequence models, and provides sound estimates of the human health consequences of explosive terrorism attacks in open-air urban and rural environments.

Jan 1, 2018

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020