Search Documents

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By D. J. Barrett, M. A. Sochocky

INTRODUCTION Summary of Factors Influencing Comminution Circuit Design The selection of an appropriate comminution circuit for a specific ore is one of the most important decisions in the design of a processing plant. The importance is related to the fact that the capital and operating costs for crushing and grinding plant generally represent, as is well known, the major portion of the plant costs. This chapter will, therefore, identify as many as possible of the factors which influence the selection of a comminution circuit. The number of factors which will have to be considered for any comminution project will depend, among other things, on the type of project. If, for example, the project is an entirely new mining development, then most, if not all, the factors identified will have to be analyzed. If the project is an expansion of a developed mining operation or if the new orebody is adjacent to a viable operation, then the existing operation will influence the choice of factors or design constraints which need to be considered. The existing infrastructure or supporting systems may be quite adequate to accommodate the requirements of any expansion or new development. Hence, those factors may not have to be considered. To cover, however, the widest spectrum of projects, the factors which have been identified in this chapter are those which will have to be considered for the most complex of projects, that of developing an entirely new mining operation. The range of factors is as broad as the range of different ore types. Thus, each development must be treated with individualized care. The most important step in the development is the analysis and understanding of the ore characteristics. The hardness of the ore, its abrasiveness, friability, moisture content, grade, mineralization including gangue mineralization, liberation size, chemistry, and other characteristics should be the first to be analyzed in the investigation. The next should be the determination of factors such as plant size, throughput, location, climate, accessibility, and availability of water. The selection of samples for initial bench scale work and bulk sampling (when needed) for further

Jan 1, 1982

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

Applications of proven real time, through-conveyor elemental analysis technology and benefits achieved will be discussed using case studies in base metals, iron ore and phosphate operations. PGNAA (Prompt Gamma Neutron Activation Analysis) technology and its background in minerals applications and applications which are expected to further improve its utilization will be reviewed. Short payback through operational benefits such as removal of waste from feed, increased feed grade and overall improved productivity will be demonstrated based on results achieved at several processing operations. PGNAA technology is most applicable to conveyed flows as it is unaffected by belt speed, particle size, segregation/layering, mineralogy or dust. As a transmission method able to penetrate in excess of 500mm of rock it provides extremely representative results continuously measuring through the full conveyed cross section and reporting results typically on one to five minute accumulated increments to the control room. Multi-elemental results and moisture content are used for active process control: diverting conveyed flow increments(bulk sorting), blending ore types in plant feed, and providing advance warning of significant quality changes to the downstream plant operators (e.g. flotation). Elements of interest may include deleterious components as well as target metals. Ore feed quality measurements are also useful in metal accounting, ore reconciliation and real time feedback to mining operations. Further benefits can result when combined with other technologies such as particle sorters, to upgrade diverted increments of subeconomic material to achieve higher feed grades and lower deleterious content to the main process. Measurement of elements (e.g. silica) which correlate with ore hardness or grinding characteristics can be used to moderate feed rate to grinding mills to prevent overload, hence optimizing grinding performance and reducing energy and grinding media consumption. Pebble flows can be analysed and uneconomic increments diverted to prevent recirculating flows consuming mill capacity unnecessarily. This also increases average feed grade.

Jan 1, 2016

Jan 1, 1915

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By JOHN R. SUMAN

IT SEEMS particularly appropriate that the Institute's Regional Meeting should be held in Minnesota this year. Whether we like it or not, we cannot help looking at things now in the light of the World War and the all-out effort we, as a nation, are making to defend our resources, our institutions, and our way of life. The ability to do this lies in large measure in the ability to forge weapons of defense-the machines of war. The basic ingredients of any defense system, or war machine, are the raw materials of industry-iron ore, providing steel for guns, shells, tanks, and warships; coal for stoking the nation's furnaces; oil to furnish power for war planes, ships, trucks, and mechanized weapons; and all the other materials that play a vital role in the operation of modern armies and navies. The tremendous requirements of full-scale defense programs are indicated by the large number of commodities that are now under priorities because the supply is not sufficient to meet both defense needs and all normal civilian consumption. But out of all these items two are of paramount importance-steel and petroleum. In this age no nation can hope to main¬tain a position as a first-class power in the world without a highly developed industry, particularly the heavy industries based on steel, and without access to the necessary resources for those industries. In 1918, 70 per cent of the iron and steel production of the United States was required for defense purposes. In 1940, 15 per cent of our iron and steel production was consumed for defense purposes, and with the acceleration of the defense program, it appears that the proportion of steel output required for defense purposes will reach 40

Jan 1, 1941

By Malcolm Scoble

School Values ?? Each other; ?? Students, & helping them develop intellectually, personally & professionally; ?? Freedom to pursue educational & research opportunities; ?? Home-work-life balance; ?? The geographic-business community in which we operate ; ?? The pursuit of excellence; ?? Our contribution to society; ?? Creativity & innovation; ?? Teamwork & collaboration; ?? Career development, achievement & reward.

May 1, 2008

By Rafael Colás

Computer visualization can be employed in industry as an aid to the understanding of the complex interactions between variables encountered in production. The examples of ingot casting of rimming steel and that of hot rolling of low carbon steel strip are presented. Both processes are mathematically modeled, and their results are presented in a graphical way. Such models have been proven to be an asset in quality improvements and increase of productivity as the personnel involved get a better understanding of their job.

Jan 1, 1993

By Charles H. Jones

Jan 1, 1905

By K. K. Clark

Excessive injection pressures in water injection wells may create deeply penetrating fractures, or may open up existing reservoir fractures. If these fractures are oriented toward offset producing wells, oil recovery at injected water breakthrough and ultimate recovery will be impaired. A method of calculating fracture lengths from pressure fall-off test data is presented. The method is based on a linear flow model that simulates conditions present during the early-time period after shutting in an injection well. Fracture lengths can be calculated directly if formation permeability is known. A graphical technique is presented that provides fracture lengths based on permeabilities calculated from normal fall-off tests, where those permeabilities are adjusted for flow geometry. Test data from four injection wells and results obtained from applying the method to these wells are discussed. Introduction Rates of water injection into nonstimulated wells in low permeability reservoirs frequently fall below economically desirable levels. Therefore, some form of stimulation such as hydraulic fracturing often is performed on these wells. Usually these fractures penetrate a short distance from the well — short as compared with interwell spacing — and therefore should not create problems of water channeling to offset producing wells. In the past, some operators have been tempted to increase injection pressures continually to maintain a specified injection rate. But pressures cannot be increased indefinitely. Field data indicate that continued injection above fracture opening pressure can cause excessively long fractures to approach between well distances. If these long fractures intersect or closely approach offset producing wells, premature water breakthrough can result. It is difficult to seal effectively these fractures by various workover procedures after premature water breakthrough has occurred. This paper describes testing procedures that are potentially capable of detecting premature water breakthrough before it occurs. Knowledge of fracture lengths and fracture opening pressures can assist field engineers in selecting optimum operating conditions for water injection wells. Fracture lengths should be calculated from pressure fall-off tests on injection wells, and maximum permissible iniection pressures should be determined from step-rate injectivity tests. Equipped with this information, the field engineer is in a better position to recommend for a particular injection well the optimum operating conditions that will lessen the chances of channeling to offset producers. Historically, pressure transient tests have been conducted primarily on producing wells and analysis procedures have been based on radial flow concepts. Several authors have suggested that these same procedures be applied to tests conducted on water injection wells. This application is justified for wells that are not connected to extensive fracture systems. However, if the formation is severely fractured, the interpretation methods must be modified. Several authors have presented the pressure response of various systems that are intended to simulate reservoir conditions. A paper by Russell and Truitt* on vertically fractured svstems is probablv the most useful from the standpoint bf the fieid engineer. Russell and Truitt presented the pressure-vs-time behavior of a well connected to vertical fractures with various fixed lengths. Their permeability adjustment technique is used in this paper to refine methods of calculating fracture length and interwell permeability. Theory and Definitions Three flow-system geometries are considered in analyzing injection well test data. These various geometries are applicable during specific time intervals of transient pressure tests. Schematic drawings of the flow models, and the time intervals over which they are applicable, are shown in Fig. 1 in the chronological order that they are applied to the pressure response of water injection wells in fractured formations. The very early response is simulated by an infinite linear system as shown in Fig. 1A. This representation permits the calculation of matrix surface area exposed to the fracture. The model shown in Fig. 1B is identical with the one studied by Russell and Truitt. They evaluated the transient pressure response of this vertically fractured system by finite difference techniques. The results were presented as tabulations of dimensionless pressure drop functions for a range of fracture lengths. A semilog plot of these data shows that the apparent matrix permeability can be related to the true matrix permeability by a simple exponential function. Their adjustment factor is used in this paper to improve the accuracy of matrix-permeability and fracture-length calculations.

Jan 1, 1969

By Joshua Hofman, Braden Lusk, Erin Morris

Explosions in urban environments, whether of accidental or malicious cause, often result in extensive injuries, loss of life, and property damage. The ability to predict the damage inflicted by these events is highly sought after; in order to predict damage, the behavior of blast waves within these environments must be quantified and understood. Urban constructs such as buildings and roadway intersections affect the natural propagation of a blast wave, intensifying or rarefying the wave depending on their arrangement.

Jan 1, 2012

By Fuller, T. S.

THE number of rare or uncommon elements in use in the electrical industry nowadays is large, their application having come about through investigational work in industrial search laboratories and ' educational institutions. Such elements, together with those whose properties are more generally known, constitute Nature's gift to mankind and make possible the intricate devices which further our modern civilization. The' quality of raiaity is one of degree, and obviously depends largely on one's point of view. From the standpoint of quantity measured in the customary units of weight and volume, the amounts of many of the elements required are extremely small, but from the of view of performing some particular function or .other in a manner more satisfactory or cheaply than can be accomplished by any other sub- stance, the use in question may be extremely important.

Jan 1, 1928

By Thomas H. Kleine, Alan R. Cameron, William W. Forsyth

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By K. V. S. Sastry, A. J. Hunt, K. D. Lofftus

Sol-gel processing is rapidly becoming an important process for producing such advanced materials as high activity catalysts, fiber optics and ceramic precursors. These materials can be tailor made with properties unique to sol particles as well as the gel aggregates by controlling production of the sol, the formation of the gel, and the removal of the interstitial fluids. This paper presents colloidal and kinetic principles of sol generation and gel formation. Hydrolysis of alkoxides provides the best means of controlling sol production and electrostatic stabilization enables the formation of the most homogeneous gels. Gelation occurs by hierarchial aggregation which produces inhomogeneities much larger than the sol particles. Colloidal and kinetic principles can be applied to reduce the size of the inhomogeneities and obtain high performance transparent insulation and new ceramic composites.

Jan 1, 1990

By J. David Lowell

On a low desert ridge six miles south of Cairo lie the remains of the world's earliest known mining town, Maadi of predynastic Egypt. Copper artifacts, including ingots and an ax head which was spoiled in casting, indicate that copper ore was smelted in Maadi, and radio- carbon dating has placed the activity at least as early as 3300 B.C. This is the oldest documented date for the use of smelted copper, the first industrial metal used by man. Copper was mined and smelted almost as early in Asia Minor and on the island of Cyprus, but the greatest development of the budding copper industry was in Egypt, where specific historical records show that about 10,000 tons of copper metal were produced in the period from 1850-1580 B.C. Contrast this production of 35 tons per year with the present world production of about 7 million tpy.

Jan 1, 1970

There are several simulators available and are being used for analysis, improvement and optimal control of the grinding process. However, these tend to be developed on informal software engineering methodologies. The informal approach is not suitable for long term development and a formal design methodology is necessary to develop efficient, error-free, and easy-to-use and to maintain software. In meeting this goal, basic concepts of a software model for describing the mineral process objects has been proposed. The software model forms the basis for software design and efficient implementation of the simulation. This paper describes the development of software models for grinding circuits. The work constitutes the theoretical foundation for the development of an advanced simulator for comminution.

Jan 1, 1995

By C. E. McWhorter

IN underground mining recent trends toward mining large tonnages of low-grade ore have created, among other things, a need for cheaper and more flexible ore transport. A relatively new development has been the adaptation of shaker conveyors to meet this need. Although widely used in coal mining, only in the last few years have shaker conveyors been used in underground metal mining. The equipment consists of a driving engine, either electric or air powered, upon which is mounted a drive trough supported in ball-bearing frames. The trough line, or conveying medium, is made up of a number of sections, each section connected to another, usually with bolts. The length of each trough section is controlled by the length that can best be handled underground, but is usually from 9 to 13 ft over-all. The length of a complete conveyor line is determined by the character and weight of material to be handled as well as by the size of the ore body. Trough lines vary in lengths from 100 to 300 ft and the trough has a cross-section area of 127 sq in., and is 22 in. wide by 6 ½ in. deep.

Jan 1, 1948

By E. H. Mohr

AT the McGill concentrator of the Nevada Consolidated Copper Co., all flotation operations have been carried out in Forrester cells since November, 1926. In respect to cost of operation, the new cell has proved to be superior to the Callow, which it supplanted, and its incorporation in the flow sheet has resulted in a marked improvement in the metallurgy. Before citing the advantages of the new machine over the old, it should be explained that the Forrester has not only replaced the Callow, but it has made possible the elimination of a number of tables as well. When Callow cells were in use, table concentration preceded flotation. The ball mill pulp was elevated, by means of air lifts, to roughing Wilfley tables situated two floors directly above the flotation floor. On an intermediate floor were additional tables which cleaned the concentrate from those above. The finished table concentrate constituted approximately 60 per cent. of the total mill production, and contained about 40 per cent. of the recovered copper. The table tailings were returned to the classifiers, the overflow from which went to the flotation cells and the oversize to the ball mills. As soon as the Forrester cells were installed, this tabling operation was discontinued. The ball mill pulp now discharges into the classifiers direct, without the intermediate tabling. It was impracticable to employ the present flow sheet when Callow cells were in use, for the reason that unless the greater part of the heavy mineral was first removed, it accumulated on the mats and adversely affected the flotation operation. By tabling ahead of flotation, it was practicable to maintain the concentrator at 10 to 20 per cent. greater capacity (depending upon the pyrite content of the ore) than was possible by flotation alone. This was due to the necessity for finer grinding in the latter case. Even though the table concentrates contained only 6 to 8 per cent. copper content, the low smelting costs made it advantageous to operate at high mill capacity, at the cost of low grade of product.

Jan 1, 1927