Search Documents

By K. Hanumantha Rao, K. S. E. Forssberg, F. Su

The influence of reagents dosage, pH, temperature, and particle size on the kinetics of apatite flotation response from magnetite has been investigated. The first-order models characterizing rectangular distribution and fast and slow distributions (F-S model) of floatabilities gave an excellent fit to the results of apatite flotation when compared to other models. However, the latter model is found to be better than the former in the goodness of fit and also in the description of flotation performance. The kinetic parameters in the F-S model are estimated by using a nonlinear least squares fitting program. The ratio of fast and slow rate constants is observed to be an important parameter for identifying the optimum levels of the variables and to outline the selectivity between apatite and magnetite. The influence of collector dosage is realized from the model parameters by relating it to the fraction of slow- floating particles. An attempt has been made to describe the apatite flotation behavior with the determined model parameters.

Jan 1, 1999

By J. M. Hodge, M. A. Orehoski

tions to which it will be subjected, and this premise is probably the most important reason for hardenability control. However, the criterion of hardenability [ ] ture after quenching should consist wholly of martensite; and that transformation of austenite to intermediate-temperature products during quenching will have a deleterious effect upon the physical properties, particularly the toughness, of the tempered material. This implies that, in order to obtain the optimum physical properties from a given steel, its "hardenability" should be high enough to suppress all transformation except that to martensite under the heating and quenching condi- IT is now generally conceded that if a steel is to develop optimum physical properties in the conventionally quenched and tempered condition, the microstruc- [ ] that at present is most widely accepted and used is based on a microstructure of 50 per cent martensite. This criterion, which was suggested by Grossmann,1 does have considerable justification. It may be readily measured by a fracture or etch test and, since it represents the point at which the hardness is changing most rapidly with variations in cooling rate, it may be determined empirically from a hardness-depth curve by determining the point of steepest slope (the inflection point. Furthermore, in plain carbon steels or in steers of low hardenability, the difference in hardenability expressed in

Jan 1, 1945

By B. H. Weber

"Industry generally has become noise-conscious and is realizing that damage to the human ear is expected to become more costly than any other compensation. Noise control has been recognized as a necessity and, fifteen years ago, in co-operation among different countries, inter-national organizations were set up to co-ordinate measures against dangerous noise and the development of silencing devices began. Rock drills for underground operations were particularly scrutinized because of the explosive nature of the noise developing from air escaping from exhaust. This paper describes the results and the present stage of development in the reduction and control of noise on rock drills, with special application to their use in mines."

Jan 1, 1970

By Dever C. Ashmead

COAL companies in the anthracite region are studying various methods of mining that will permit a considerably shorter life of gangway and therefore a decrease in the maintenance charges. Maintenance charges in the upkeep of gangways where the measures are steeply pitching are high due to the excessive cost of the replacement of timbers and the cleaning up of falls. Therefore, if the length of gangway in the coal beds can be decreased and the mining more concentrated, the life of the coal gangways will be decreased and consequently the maintenance charges will be lower per ton of coal produced. Customary practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced.

Jan 1, 1925

By Augustus Locke

Jan 1, 1923

By Augustus Locke

Jan 1, 1923

By J. R. Coleman, G. L. Corrigan

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

The Nickel Rim Depth Cu-Ni-PGE deposit, discovered by Falconbridge Limited in 1993, illustrates several trends in exploration in the Sudbury area. Recent discoveries tend to be deep, high grade, footwall hosted, close to or straddle property boundaries and made using a multi-disciplinarian exploration approach that integrates economic considerations with geology, metal geochemistry and geophysics (borehole EM). The Nickel Rim deposit occurs down dip of Inco's Victor Deep deposit (4.2 million tonnes at 2.25 per cent Ni, 7.30 per cent Cu) in the eastern margin of the Sudbury Igneous Complex (SIC) at a depth of 2650 m. Before commencing drilling an economic evaluation was done to determine the minimum size needed to be economic at the expected depths and determine the expected value of an exploration venture. The subsequent surface exploration program discovered a drill indicated, undiluted mineral inventory of 1.6 million tonnes of 1.58 per cent Ni, 10.13 per cent Cu, 4.17g/t Pt and 3.50 g/t Pd including 519 000 tonnes of 4.13 per cent Ni, 25.53 per cent Cu, 9.76 g/t Pt and 8.42 g/t Pd. The deposit is hosted by gneiss, migmatite, gabbro and pseudotachylite (Sudbury Breccia) 100 m below the base of the SIC.

Jan 1, 1996

By H. M. Chance

Adequate treatment of the difficulties surrounding the valuation of mineral lands requires that agreement be first reached defining value as understood for the purpose of appraisal. To define value as the price of a product is not sufficient, and does not assist us in using the factors that cause variations in values and in relative values. The real value of any product depends primarily upon its relation to the necessities, comforts and pleasures of mankind. As the necessities, comforts and pleasures of the civilized races differ from those of more primitive man, the value of products varies with the degree of civilization and the environment of the consumer. Coal has no value to the savages of warm climates, and arrow-head flint none to the residents of New York. It has long been recognized that what has been termed " intrinsic value " must be limited to materials that are essential to existence—air, water, food. But " intriusic value" cannot be measured in monetary terms. The intrinsic value of a bushel of wheat is due to the fact that it will support the life of an individual for a certain definite time, but this fact does not enable us to measure or to express that value in monetary terms. It has often been proposed to adopt as a measure of the value of any product the quantity of labor necessary to produce it, but this method is of limited application, and will not apply to what may be termed " intrinsic values." For many reasons it might be well, while assenting to the fact that any material may be intrinsically valuable, to abandon the use of the term " intrinsic value." One of these reasons is the tendency to confuse the idea of intrinsic value with a value that is conferred by economic conditions, that is purely artificial and that may be permanent or evanescent. Intrinsic value must from its nature be permanent and unchangeable. Possibly for present purposes the value of any material may be considered as having a dual origin: First, that due to economic

Jan 1, 1914

By G. L. Corrigan, J. R. Coleman

FOUR factors that largely determine the end product obtained when cement and water are mixed are the chemical composi-tion of the cement, the fineness to which the cement is ground, the amount of mixing water used, and the procedure used in mixing the slurry. In order to study the effect of two of these factors, the other two, the chemical composition and method of mixing, are kept constant, leaving as variables fineness and water-cement ratio. Through years of experimentation and usage it has been well established that the reduction of cement clinker to a very fine state by grinding improves its cementing value, principally because the reaction between cement and water takes place only at the surface of the cement particle, further action being hindered by the accumulation of reaction products that tend to coat the unreacted material. Therefore, the moE finety-ground %cement, and the greater the surface exposed in propor-tion to its mass, the more rapid is the The work covered by this paper was done by the authors in pursuance of graduate studies in the ~epartment of petroleum Engineering at The University of Texas. The present paper is a condensation of a more detailed DaDer from which, for brevity, information such as the procedure for determining permeability and some of the discussion and procedure relevant to slurry volumes and fineness of cement have bsen deleted. It was felt that this information would not be of interest to most readers and should be outside the scope of this paper. Manuscript received at the office of the Institute Aug. 16, 1940. Issued as T.P. 1266 in Petroleum Technology. January 1941. hydration rate. Similarly, the greater the surface exposed, the greater the proportion of the cement that reacts, and the lower the amount of residue that is unreacted and so remains inert and unable to make any contribution to cementing properties.] Although it is more expensive to manufacture a finely ground cement than a coarser cement, the advantages of fine grinding of construction cements were so marked that the fineness of cement has increased considerably in past years. When the manufacture of special oil-well cements was begun, it was necessary to consider properties of cement that previously were considered of minor importance, foremost of these being pumpability. Since, with the water-cement ratio constant, a finely ground cement will produce a neat slurry of higher consistency and shorter time of pumpability than will a coarser cement, there is a tendency to grind oil-well cements to a lower degree of fineness. Therefore, in order to produce oil-well cements that will make a slurry having a long time of pumpability, cements are manufactured that because of their coarseness generally are Poorer cementing materials than some of the more finely ground construction and on the other hand, often it is necessary to Pump oil-well cements for long periods of time to place them properly behind a string of casing in a deep well, and since high strength is not of foremost importance for such cement, there is room for considerable controversy concening the proper fineness range.

Jan 1, 1941

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

In a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress,t The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term ilfracture stress' has come into use with the same significance as 'ctechnical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens betqrcen yield and fracture, A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress s3 to the longitudinal stress S1.* The results of the experiments are represented by a series of their flow-stress curves for each Of the metals investigated, and these diagrams have been used for the development Of Other diagrams Of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not On the stress system, he was 'Orrect in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, "auld Seem to be axiomatic, provided that the flow Stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard Of this principle has led to some untenable theories Of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1949

By F. R. Hensel

THE absorption of oxygen by molten metals is a quick and convincing method to determine the metallurgical characteristics of various types of furnaces.1 The investigation was restricted to the use of coreless induction furnaces. A major variable in induction furnace practice is the frequency and its influence was studied by comparing melts made in a 5000-cycle and a 60-cycle induction furnace respectively.2 The authors are not aware that such a comparative study has been made before and therefore present this paper in the belief that the results will be of general interest. ANALYTICAL METHODS FOR DETERMINATION OF OXYGEN IN NICKEL An analytical procedure for determining NiO by a quick and simple, laboratory method has been worked out in collaboration with Dr. Herty, of the Pittsburgh Station of the Bureau of Mines. It was found that Dr. Herty's aluminum method as used for the. determination of FeO in iron and steel was very suitable for use with nickel if instead of hydrochloric acid a 10 per cent solution of nitric acid is used for bringing the metal into solution. Essentially this method involves deoxidizing the nickel-oxygen alloy with aluminum (2Al + 3NiO = Al203 + 3Ni) and determining the resulting Al203 by a residue analysis. The original oxygen content can then be calculated from the amount of Al-20,. The method as suggested by Dr. Herty3 is referred to in the present paper as method B. A slight modification of method Bled to the application of method A, a description of which is given below according to F. W. Beiter?:3

Jan 1, 1932

By George H. K. Schenck

The investment analysis methods that are most generally accepted in the mineral industries in the mid-80's are presented along with their advantages and disadvantages. Also covered are current widely-used practices for introducing the uncertain nature of most of the important variables in an investment analysis, which is contrasted to the former dominance of deterministic analysis. Finally, the discussion turns to current practice for handling the two critical areas: cost of capital and inflation. The advice contained is reinforced with data from a survey of current practices in the petroleum industry.

Jan 1, 1985

By J. A. L. Napier

Computer programs which rely on the assumption of linear, elastic rockmass behaviour have been used routinely for many years in the South African mining industry to determine the stresses arising in the vicinity of mining excavations. A description is given of the theoretical background and novel solution techniques used in the recently developed MINSIM-D boundary element program. Features of the program include the ability to analyse multiple interacting reef planes at arbitrary orientation to one another, slippage on fault planes and the effects of backfill placement in mined areas. Incremental mining sequences can be modelled, and digitizer and front-end routines have been written to assist in the capture of mining outlines and general problem specifications. A brief indication is given of design problems for which MINSIM-D is appropriate, as well as some future extensions of the system.

Jan 1, 1987

By A J. Moore

To control the airblast from blasting to regulatory limits at environmentally sensitive sites near the Collinsville Coal Mining Operations, it has been necessary for Thiess Mining to incorporate a wavefront reinforcement analysis model in the predictive environmental airblast design. Controlling airblast from cast blasting 70 m high faces with 2000-3000 kg of explosives per hole within 700 m of houses presents a considerable challenge to the blasting personnel. This paper describes the model used and summarises the results of an investigation designed to quantify the increase in airblast indicated by wavefront reinforcement diagrams to further calibrate the model for future prediction.

Jan 1, 2004

Jan 1, 1960

By Norihiko Fukatsu

In order to use effectively the previously reported new sensing system for hydrogen and oxygen potentials in molten copper, the criteria of the potentials for getting sound castings have been determined in the laboratory experiment. The copper melt equilibrated with a given hydrogen and an oxygen potential was rapidly quenched in the crucible. The relations between the holding potentials and the gas porosity in the solidified sample were investigated by measuring the density of the sample and microscopic observations. It was found that the defects of the gas porosity became the maximum at the potentials where the dissolved amount of hydrogen and oxygen was in the mole ratio 2:1. The samples having the density more than 99% of the theoretieal value were obtained in the higher oxygen and lower hydrogen potential region or in the lower oxygen and higher hydrogen potential region. The criteria thus determined were examined by comparing with the measured potentials in the practical casting machine. In tough-pitch copper casting, the problem due to gas porosity was found to be serious when the hydrogen potential increased. In the. oxygen-free copper casting, the evolution of hydrogen was found not avoided. The gas porosity in the casting, however, was found eliminated when the oxygen potential was kept at a low value.

Jan 1, 2003

By N. S. Greensfelder

THE firing of explosive charges by electricity dates back to 1745 when a Doctor Watson is said to have used an electric spark for igniting gunpowder. His method failed in practical application because, to ignite blasting powder, heat must be applied for a period longer than the duration of an electrostatic spark; Wheatstone found that this does not exceed 14000 sec. The usual result, therefore, of an electrical discharge in gunpowder is to scatter the grains, without igniting them. Benjamin Franklin partly overcame this difficulty by confining the powder and crushing grains that lay in the line of discharge. In 1822, after the primary cell had been discovered by Volta, Robert Hare, professor of chemistry at the University of Philadelphia, noticed the heating of a short piece of wire placed in the circuit of a voltaic battery. Later work by Oersted, Faraday, Wheatstone, and Henley resulted in the development of the magneto blasting machines. Fulminates of gold and silver are thought to have been discovered by Cornelius Drebbel, about 1600. Pepys, in his diary for November 11, 1663, recounts a conversation with Doctor Allen, who told him about aurium fulminans "of which a grain ... . put in a silver spoon and fired, will give a blow like a musquett and strike a hole through the silver spoon downward, without the least force upward.1," This fallacious belief that explosives act downwards only, is still held by many who should know better. Fulminate of mercury was discovered by Howard in 1799. J. Shaw of Philadelphia is said to have invented a fulminate-of-mercury cap in 1814; his idea was later adopted by gunmakers in England and France. The principal advantages of

Jan 9, 1922

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

THE recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by . Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presented in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization with additional data will be completed in the near future by the writers.

Jan 1, 1935

By George Moore

IN spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which compli-cate the effects; and (3) the fact that the body-centered cubic modifica-tion does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions.

Jan 1, 1939