Search Documents

By M Coulthard, J Rivalland, K Dugan

Prior to 2001 Yallourn Mine has pumped approximately 1000 Megalitres of water per annum from aquifers beneath the mine floor in order to control aquifer pressures that were thought to have an influence on mine floor and permanent batter stability. In 2001 one of the deep aquifer pumps was shut down for five months in order to measure the aquifer recoveries. Prior to the shutdown a UDEC model was created in order to predict what level of recovery in the aquifer pressures would be critical to mine stability. The shutdown showed that the aquifer levels recovered and stabilised at levels that did not threaten the stability of the mine. The aquifers recovered to levels below the critical levels identified in the UDEC model.

Jan 1, 2003

By R. Dekkers

Non-metallic inclusions in liquid steel are mainly formed during killing. As far as these particles are not captured by the slag, they are found in the cast steel where they can deteriorate the mechanical properties. Inclusions may also disrupt the continuous casting process, affecting thus directly the quality of the steel and the production capacity. Steel pin samples from the Sidmar plant (Belgium) were taken in different steps of several ladle treatments and in the tundish. Also slab samples were studied. All samples concern the same type of low alloyed aluminium killed steel. The non-metallic inclusions were isolated from the steel matrix and investigated with scanning electron microscopy and energy dispersive spectrometry. The evolution of the non-metallic inclusions is described by their number, size, shape and elemental composition. The main non-metallic inclusions present are aluminium oxides and spinel type compounds.

Jan 1, 1999

Jan 1, 1957

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By Neillm Alastair S.

"This paper looks at what has happened in the past decade in the rare earth industry, particularly for those companies outside China trying to develop alternative projects to the Chinese dominated supply chain. The rare earth industry has gone through a metamorphosis over the past decade. The industry was basically unknown outside China until overnight it became the next hot topic on the financial streets of Canada and Australia. Suddenly various junior miners shifted from uranium and other out-of-favor commodities to rare earths as funds were easy to access from an investment community that did not understand the complexities of the space. The initial funding was done on traditional junior mining metrics of grade and deposit size. This has morphed over time to:1) Lights versus heavies2) Making a concentrate3) The importance of separation4) Off-take agreementsAt the peak of the market frenzy certain flagship operations were built using the “Not Made in China” moniker. Unfortunately certain errors were made during implementation, which are finally coming to the surface and making the rest of the pack wondering what will happen next. A review and update of some of the mistakes made and lessons learned will be discussed.BACKGROUNDAbout ten years ago awareness started to form around the rare earth industry and various groups recognized that because of the closure of Molycorp, Mountain Pass, and the dominance of China, there was a risk of uncertainty of reliable supply. This was not news for those active in the industry like Rhodia (now Solvay), the Japanese, South Koreans and other key consumers but to others it was like a light went on and rare earths became the new “.com” trend for investment banks, investors and some mining companies looking for the next hot topic.In the late 1990’s Molycorp accounted for around 20-25% of the world’s supply of rare earths, mostly lights (La, Ce, Pr and Nd), with small amounts of heavies from other sources. Then environmental issues forced the closure of the operation at Mountain Pass. Within six months China had increased production to plug the gap in supply. Around that time China was developing a strategy to leverage their position in rare earths and implemented a series of regulations to increase the value added component of rare earths inside China."

Jan 1, 2016

By J. MURRAY RIDDLELL

AN increase of 18 per cent in the production and consumption of all metals last year was readily met by the mines, but more than an average amount of development work was made necessary. Mining methods were improved appreciably; open-pit operations ad¬vanced more than underground practice: and the transportation phase of mining progressed to a greater extent than the other related functions. A new belt-conveyor system of mining was placed in operation at the Spruce open-pit iron ore mine at Eveleth, Minn. The gathering portion of the belt system was installed beneath the surface of the open pit, following closely the bottom rock, in especially provided drifts; beyond it inclined upward to the surface and finally discharged into a 500-ton shipping pocket. Length of the belt was 4500 ft. net vertical lift 386 ft. and capacity 750 long tons per hour. The mined ore found its way to the belt through one of three vertical raises, whose horizontal section was 10 by 10 ft. Each raise was equipped with a grizzly, crusher, pan-type feeder, and auxiliary equipment. Transportation of the ore from the working faces of the pit was accomplished as follows: (1) Two raises were equipped with tower and anchor stations, 3-cu.yd. drag scrapers, and related power units; (2) the remaining raise was provided with electrically driven power shovels and 20-ton trucks mounted on pneumatic tires. This installation has entirely replaced railway pit haulage and partly eliminated power shovels. In a similar

Jan 1, 1938

By Yazen Khasawneh, Osvaldo P. M. Vitali, Mohammad Nassim

The demand for renewable energy is growing as the conventional energy resources are becoming more limited and we are more conscious about the negative impact of conventional energy sources on the environment. Wind turbines technology is evolving in a fast pace, the towers are becoming taller, and the rotors are getting larger. The challenge is to maintain the Levelized Cost of Electricity (LCOE) as low as possible to ensure a sustainable and an economically feasible energy supply. Thus, the foundation systems for wind turbines should evolve to meet the increasing load demand, while reducing the LCOE. In this paper, an innovative foundation system for onshore wind turbines is presented. The new foundation system is the conventional P&H tensionless pier foundation (PHTP) with a reinforced concrete collar at the top of the pier. 3D FEM modeling was conducted to assess the benefits achieved by adding a collar at the top of the PHTP foundation. The numerical results show a significant performance enhancement of the proposed foundation system over the conventional PHTP foundation. The enhanced foundation system also has an economical advantage because the depth of the pier can be greatly reduced while maintaining a superior performance.

Sep 8, 2021

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By Boger D. V

Two industrial case studies in which detailed investigation of the flow behaviour of mineral slurries is used to assess the feasibility of pipeline solid transport are described. The first example deals with the pumping of highly concentrated bauxite tailings to disposal, while the second exam- ple examines the possibility of transporting high-density Victorian brown coal slurries which previously has been thought as uneconomical. It is demonstrated that these typical solid handling problems can be solved by a good understanding of the rheology of suspensions.

Jan 1, 1989

By F. H. Hueston, R. S. Barclay

"Depending on the application, zirconia, fused magnesia and graphite have been found to be the most suitable crucible materials for melting uranium metal and its alloys. Although graphite has been found to be satisfactory for uranium and uranium alloy castings with cross sections of 4 square inches or greater, ceramic-type molds are superior for small sections and those shaped castings which prohibit the economic use of machined graphite molds. Heating cycles, addition mechanisms and furnace conditions for melting are discussed."

Jan 1, 1967

By Ali Ebrahimi, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, Roneet Das, William Tanner, Amir Ahmadipur

There are safety concerns related to operation of heavy equipment over coal combustion residual (CCR) impoundments during construction of the impoundment closure programs. As part of a pilot study prior to a full-scale closure construction, an access pathway and working platform were designed and constructed to facilitate equipment access for construction of deep soil mixing (DSM) zones on the ash delta of a CCR impoundment. The access pathway and working platform was constructed using shallow mass mixing with cement at the CCR surface to address safety concerns related to the geotechnical behavior of CCR. This paper describes the data from the instrumentation system which was implemented to monitor the geotechnical performance of the CCR during the pilot study. The instrumentation system included monitoring of the ground movement, vibration, and porewater pressure within the ash delta of the CCR impoundment during a pre-construction load testing, equipment mobilization over the access pathway, and DSM column installation over the working platform. INTRODUCTION A deep soil mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment to evaluate mix designs and construction techniques for the regulatory closure. The DSM columns will create a wall which will separate and retain the CCR in a consolidated footprint separate from the closure by removal portion of the footprint and provide a barrier between the two areas of the surface impoundment. Historically, the surface impoundment received CCRs including fly ash, bottom ash, boiler slag, and gypsum, along with other byproducts produced from flue gas desulfurization (FGD). The predominant CCR in this impoundment were fly ash and bottom ash. The primary goals of the DSM pilot study were to assess the mix design strengths and to evaluate DSM construction techniques that could reach the design mixing depths of up to 90 ft. The DSM test columns were installed on the CCR delta approximately 500 ft from the nearest impoundment dikes. Another objective of the pilot study was to develop, construct, and monitor an access pathway for safe passage and movement of construction equipment on the CCR delta.

Jan 1, 2019

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By Donald L. King

This paper has been prepared with the objective of providing basic information on thickening equipment as applied to mineral processing plant design. Thus, by design, the content is elementary, yet sufficiently informative to advise the reader concerning the thickening and clarifying process, equipment configurations, installation and operation. Practical considerations are provided for slurry samples for testing, evaluation of testing, preliminary sizing, duty classification, and thickener selection to enhance operation, see icing and control. Illustrations are provided to both inform and demonstrate present state of the art features and capability.

Jan 1, 1978

By Robert C. Stephenson

In 1954, a year when general industrial production declined, it is significant that industrial mineral products continued in high demand. Phenomenal growth of the cement industry, increase in filler-fibre markets such as for asbestos and diatomite, expansion of the gypsum industry, and the increasing production of agricultural raw materials all illustrate the vitality of industrial minerals fields. Pioneer development of new industrial raw materials-wollastonite as a current example-requires keen foresight, hard work, and tremendous intestinal fortitude. The present-day requirements of industry for rigid quality control and uniformity of raw materials have resulted in highly specialized

Jan 3, 1955

By Ezio Martino Buselli Cánepa

El programa de remediación de la Bahía de Ite ha superado los compromisos establecidos en el PAMA de Southern Perú Copper Corporation para dicha zona. En este sentido, el presente trabajo describe la aplicación de dicho programa a través de un manejo apropiado del agua para establecer humedales y lagunas. La presencia de sulfatos, óxidos de hierro y la adición de pequeñas cantidades de materia orgánica (estiércol) han creado condiciones apropiadas para la generación interna de alcalinidad y la formación de sulfuros de hierro que posteriormente serán incorporados en los sedimentos, de forma que se genere especies de flora y fauna, como ecosistemas altamente productivos en la zona utilizada.

Jul 31, 2003

By Bruce W. Gonser

TIN is not yet classed as a rare metal, but it has taken a long stride in that direction in the last ten months. It is now in Group 1 of the War Production Board's critical list, along with such company as magnesium aluminum, and nickel. This is in sharp contrast with the position a year ago when the supply well exceeded demand, and tin was used when feasible in place of really scarce metals. The geographical sources of tin production in recent years are shown in Table 1. Preponderance of former production in southeastern Asia, particularly Malaya and the Netherlands Indies (but all now controlled by the Japanese). is entirely too marked to be funny. Of the 1940 known world production of 237,000 long tons nearly all was controlled by the United States, Great Britain, and their friends. Now their supply is from countries that produced only 28 per cent of that amount. This excludes China and Australia, which because of shipping difficulties and local consumption, cannot be expected to export much tin. In spite of some expected increase in production, therefore, the supply is, and will continue to stay for at least several years, way below that desired for even normal uses. Although deliveries to consumers in the United States alone

Jan 1, 1942

By Craig Roberts

"While various methods are available to estimate a mining project's value, value is only established through a transaction. Comparable methods allow the value estimated for a mining project to be benchmarked against mining project values established in the market. Comparable methods thus are a key tool for ensuring value estimates are congruent with what the market would actually pay. For example, if the value estimated for a mining project using discounted cash flow analysis differs significantly from the value implied using comparable market methods, the valuator may be using metal price or discount rate assumptions that differ significantly from those the market is currently willing to pay for.The paper provides an overview of market comparable valuation approaches, and discusses some of the difficulties and limitations that arise in using these approaches. The types of market values that are typically utilised are discussed, including asset sale prices, share prices (market capitalisations), and values established in corporate mergers and acquisitions. Topics discussed include methods used in estimating a mining project's value based on the market value of the company that holds the asset, and limitations that arise because of unique features of mining projects and of companies that hold them.It is concluded that market comparable and fundamental (e.g. NPV) approaches to project valuation should not be viewed as alternative approaches to estimating project value, but rather can and should be integrated to derive a single value estimate based on both market andfandamental data. A method for integrating these approaches is discussed, and illustrated by example."

Jan 1, 2003

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

The importance of proper planning, preparation, and execution of a steady state sampling campaign for metallurgical plant assessment must not be underestimated. Careful planning can increase the amount and reliability of information from an optimum number of samples and fully utilize available plant data. It requires specification of the data required, determination of run duration sampling frequency, the selection, modification and testing of sample points and cutters, as well as organisation and briefing of plant and sampling personnel. Preparation immediately prior to sampling, the conduct of the sampling campaign itself and procedures to handle the collected samples and information are discussed. Cutter design, fabrication and use are described in detail, and typical sampling situations, for ball mills, classifiers, pipes, launders, flotation cells and thickeners are considered individually. Measurement of pulp flow rate can often resolve difficult mass balance problems, and discussion of convenient techniques is included.

Jan 1, 1976

By K. Sasaki, Y. Oriia, Shigeto Kuroiwa, H. Miki, Yuji Aoki, T. Hirajima, G. P. W. Suyantara

The effect of a sulfite reagent on the floatability of chalcopyrite and enargite was investigated in this paper. The flotation tests using single and mixed minerals were performed under various concentrations of sulfite. The flotation tests using a single mineral showed that the sulfite reagent depressed the natural floatability of both minerals at pH 9. Surprisingly, enargite was floated after the addition of potassium amyl xanthate (PAX) following the sulfite treatment, and the floatability of chalcopyrite depressed under a similar condition. X-ray photoelectron spectroscopy analysis results showed that the sulfate species increased after the sulfite treatment on both minerals. However, the addition of PAX removed this sulfate species and rendered the enargite surface hydrophobic. This phenomenon was not observed on the chalcopyrite surface. FTIR analysis and PAX adsorption studies were performed to support this finding. The flotation of a mixed mineral was in agreement with the flotation of a single mineral, indicating a possibility for selective flotation of chalcopyrite and enargite using the proposed method. Keywords: Flotation, chalcopyrite, enargite, sulfite, potassium amyl xanthate

Jan 1, 2020