Search Documents

By George J. Karabin

Since the inception of a qualitative pressure arch theory by Haak4 in 1911, much work has been done in an effort to apply this concept to underground mining. It has been used in both longwall and room and pillar mining to determine roadway and pillar stability (with varying degrees of success). This paper presents a summary of a case study where the pressure arch concept was extended in a totally qualitative manner to define the source of roof control problems in the mains of a Pennsylvania mine. It was concluded that, due to the method of mining employed, a pressure arch formed over a portion of the entries, and the high abutment stresses accompanying it resulted in extreme roof deterioration. The following discussion will include a general presentation of the arching mechanism, the physical response of the roof strata under mining-induced abutment stresses (both from the case study and in general), a computer simulation of ground stability under both "normal" and "abutment" stress conditions, and finally, potential means of alleviating such conditions.

Jan 1, 1982

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with the problems associated with the contamination of air and water from coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration to specific area should begin early before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants and advance consideration should be given to all the problems concerned with contaminants. The first part of the chapter will concern itself mainly with the contamination aspects of fine-coal cleaning and "black-water" disposal. Also attention will be given to the nature and formation of water from coal-mine drainage systems and the treatment of these waters for industrial use. Some attention will be devoted to the cost of installing and operating the various beneficiation systems for the removal of suspended solids. The second part of the chapter will analyze the problems of air contaminants from coal preparation plants. The nature and the effects of these contaminants and their potential for air pollution will be examined. One of the most critical is the measurement and analysis of these contaminants. As a result of identifying and determining the extent of the problem, better control can be planned. One of the most serious contaminants in air involves the element sulfur, and its elimination as a source of air pollution is one of the most challenging areas in coal preparation today. The last part of the chapter will emphasize the long-range problem of refuse disposal and control. Minimum operating and maintenance costs are functions of the proper selection and geometry of refuse disposal areas. Disposal procedures are varied but must be rigidly pursued or difficulties will result. Maintenance of refuse areas, including monitoring of burning refuse, is critical. It should be recognized that fine-solid refuse disposal systems must be carefully designed to minimize contamination. WATER CONTAMINANTS FROM PREPARATION PLANTS Pollution Aspects of Fine-Coal Cleaning and "Black-Water" Disposal The effluents from coal washeries and waters draining from plant-site surfaces inevitably contain fine coal and coal refuse materials in suspen-

Jan 1, 1968

By J. H. Perry, D. W. Houseknecth, C. A. Kertis, A. T. Iannacchione

Major problems facing the development of coal and gas resources of the Hartshorne Coalbeds include the complex distribution of minable and unminable coal, high methane content and bed pressure, faulting, variations in degree of dip, presence of natural gas fields in associated sandstones, and legal problems, caused by local geologic characteris- tics, in identifying gas origin. This Bureau of Mines study provides pertinent geologic information for long-range planning of subsurface coal and gas production from the Hartshorne Coalbeds. Pittsburg, Coal, Hughes, and Atoka Counties, OK, have approximately 1 billion metric tons (1.1 billion short tons) of Hartshorne coal in place. The methane resource of Hartshorne Coalbeds is estimated at 9.2 billion m3 (325 billion ft3) and varies with overburden and rank, These estimates were compiled from gas well density logs, coal-core data, out- crop measurements, abandoned mine maps, and the literature. The Hartshorne Coalbeds represent a valuable coal and gas resource which at present is contributing nothing to coal and gas production. This report discusses potential problems and serves as a reference for future exploration and development work. Recognition of these potential geologically related problems prior to development of this basin will reduce hazards and allow for an economic recovery of these resources.

Jan 1, 1983

By R. V. Ramani, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways (National Academy ofSciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Mar 1, 1989

By H. S. Price, J. C. Cavendish, R. S. Varga

This paper presents a new technique for solving some of the partial differential equations that are commonly used in simulating reservoir performance. The results of applying this technique to a simple problem show that one obtains accurate pressure values near wells, as well as accurate pressure pdients, which can be explicitly calculated. The method is completely rigorous in that convergence of the discrete numerical solution to the continuous solution for both pressure and pressure gradient is established. High-order, piecewise-polynomial approximations are used near the wells where pressure gradients are steep, while low-order, piecewise-polynomial approximations are used elsewhere to reduce greatly the calculation time. This combination is shown to give a uniformly good approximation to the solution. These approximations, obtained by using a Galerkin process with suitable Hermite subspaces, are shown to be theoretically and numerically superior to the usual approximations obtained from standard finite-difference techniques. Not only are much greater accuracies obtained, but computer times are also greatly reduced. The application of this technique to multiphase flow problems (e.g., single well coning problems) would have considerable practical interest, but such extensions of this technique with full mathematical rigor have not been made as yet. However, the numerical methods presented here are general, and in principle extend to multidimensional, multiphase flow. Moreover, the preliminary results given in this paper are sufficiently encouraging that we feel the effort in attempting these extensions is justified. INTRODUCTION The problem of obtaining accurate pressure distributions and pressure gradients around wells is of considerable importance in the numerical simulation of reservoir performance. The most common approach to solving this problem is to use finite difference techniques (see McCarty and Barfield9 or Peaceman and Rachfordl0). This approach, however, has many disadvantages, the major one being that many grid points are generally necessary for accurately describing the pressure distribution and the pressure gradient around wells. This need for a fine grid results in large computer times and often in prohibitively high costs. Besides investigating the method of finite differences, some authors, such as Welge and weber17 and Roper, Merchant and Duvall,13 have considered a combination of analytical and numerical techniques with some success. These approaches, however, are all nonrigorous and quite often cannot even be applied. In this paper, we present a numerical formulation of high-order accuracy, based on the Galerkin method, for solving this problem. We treat here only the partial differential equation that describes steady-state, single-phase flow. However, the methods presented are general and in principle extend to multidimensional, multiphase flow. Specifically we treat special cases of the problem in two dimensions described by: where G is a rectangle (with sides parallel to the coordinate axis) with boundary ?G, ?/?n denotes the outward normal, and y and B are non-negative constants such that y + B > 0.

Jan 1, 1970

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of the general negative perception of mining activity by the public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to control vibration at neighboring structures.

Jan 1, 2013

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By D. K. Dysinger

In this U.S. Bureau of Mines study, neodymium metal of 99.8 pct purity was prepared by electrolysis of Nd203 salts dissolved in a molten fluoride electrolyte. The metal was electrowon in a molten state at current efficiencies of 50 to 60 pct. Oxygen and carbon were the major impurities detected in the product. During operation of the small-scale laboratory cell, a number of technical problems including anode effect, low oxide solubility in the electrolyte, high neodymium metal solubility, reactivity of the metal with the cell materials, and back reaction of the metal with the anode gases were encountered. Approaches to improve cell operation and prospects for commercial adoption of the electrolytic production of neodymium metal are discussed.

Jan 1, 2010

By S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By Isaac A. Zlochower, Michael J. Sapko, Ronald S. Conti

This paper describes a U.S. Bureau of Mines investigation of large-scale coal dust explosions in an experimental mine using a high speed electro pneumatic mechanism for the rapid grab-sampling of gases and dusts. This technique enables the monitoring of pyrolysis and charring in fuel dust particles, and the collection of gaseous combustion products, in both large and small-scale explosions. Data obtained from full-scale dust explosion tests at the Bureau of Mines Lake Lynn Test facility show the following: Rapid sampling appears to "freeze" the burned gas compositions at the flame temperature values. Gas samples taken entirely in the flame zone consist of pyrolysis and combustion products with very low residual oxygen. The particles collected in the flame zone show signs of extensive pyrolysis and charring. Measurements of gas concentrations and particle flame temperatures suggest that char burning may have occurred in the flame zone.

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of inflow rate, evaporation rate, and inflow concentration. An analytical method is presented for estimating the equilibrium ground water inflow rate for use in water quality predictions. The time required to reach chemical steady-state is estimated using an iterative mass balance model. Mine operators should find the methodology useful for planning and screening-level regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 1998

By Petre Stelian Nita

In small steelmaking shops, in foundries and forging plants, there are not too many option to recycle the basic slags, which are not suitable for many purposes of recycling, because of their low chemical and structural stability. A solution of an adequate recycling is a direct recycling in EAF. Several quality requirements, physico-chemical properties and proportions of slags must be analysed. The progress in this fields permites to establish an adequate proportion of recycled slag, based on enough exact computation of the related property. For oxydizing slag, obtained during melting and in the first part of decarburization operation, the problem of phosphoms contents can be analysed using the phosphate capacity (C PO34-). For reducing periods, during deoxidization operation, desulphurization also occurs and the problem of the sulphur contents can be analysed using the sulphur and sulphide capacities ( Cs / Cs) Between this two complex thermodynamic indicators of the slags. a direct relation is established, using thermodynamic aspects, resulting from the equilibrium constants for dephosphorization and desulphurization process and also, using the optical basicity of slags, computable from the chemical analysis of the slags. On this basis starting from the steel quality requirements. adequate strategies can be established in order to obtain high rates of recycling (between 50-80%) of steelmaking slags. Important cost savings are obtained through this procedure, based on the correct amounts of the fresh lime, iron ore and fluidizers. Keywords: Slag, Properties, Recycling

Jan 1, 2003

By Charles Janin

The first successful bucket-elevator dredge to operate in California was put in comnlisvion wt Oroville in March, 1898. There had been numerous previous attempts at dredging, but noue of the earlier boats proved a success. The gold-miners in California earl3 conceived the idea of a machine to dig gravel from the beds and bars of auriferous streams that were inaccessible by the methods then employed, and it was only a few months after the discovery of gold in California that such a machine was Shipped around Cape Horn from New York to San Francisco. Thij was, however, but the forerunner of many failures in gold-dredging, and was soon at the bottoni of the Sacramento river. During succeeding years many other unsuccessful attempts mere made, and it was not until 1897 that a dredge of the single-lift bucket-elevator type mas floated on the Yuba river. This dredge was built by the Risdon Iron Works for 12. H. Postlethwaite, and would probably have been a success if it had been operated on some of the rich Ororille ground

Jan 1, 1912

By I. Casasbuenas, K. A. Nguyen, E. I. Ngoma, H. Kim, D. Borja, J. H. Park, R. A. Silva, S. Choi

"This study aimed to determine the optimum operating parameters of a continuous bioleaching system to leach arsenic (As) from mine tailings using a mixed mesophilic bacterial culture. The microbial consortium, previously adapted for effective growth at high pulp density and metal concentrations, was mainly composed of Leptospirillum ferriphilum, and Acidithiobacillus caldus. The mine tailings, collected from the Janggun mine (South Korea) contained 11% (w/w) of As. The tests were performed in a laboratory-scale unit composed of three reactors connected in series following a cascade configuration. Agitation speed, air supply, solid concentration, residence time and temperature were systematically optimized by assessing the leaching activity. Several parameters were monitored on a daily basis, including the As released into solution, iron oxidation rates, pH, cell concentration, dissolved oxygen and redox potential. Overall, improvement of oxygen transfer, by optimizing the agitation speed and air supply, presented the most tangible impact on the leaching performance. The highest As leaching efficiency observed in this study was 82%, which supports the feasibility of the process. INTRODUCTION Worldwide, around of 65 billion tons of mine tailings are produced every year (Jones & Boger, 2012). These materials comprise the waste minerals produced after ore beneficiation. Mine tailings usually contain heavy metals (e.g., Cobalt (Co), Lead (Pb), Zinc (Zn) and Arsenic (As) (Falagán, Grail, & Johnson, 2016; Nguyen, Lee, Park, & Lee, 2014). The exposure of these materials to the environment can produce serious health damage and environmental degradation (Martin, Dowling, Pearce, Sillitoe, & Florentine, 2014). Mine tailings management represents a major issue in South Korea. There are more than 1,000 abandoned mines containing stockpiled mine tailings within the territory (Choi, Park, Hong, Park, & Kim, 2013; Kim, Kim, Ahn, Ko, & Lee, 2005; Lee, Lee, & Kim, 1998). These tailings comprise high concentration of arsenic. Therefore, the Korean Government has directed its efforts to developing eco-friendly technologies, for the arsenic detoxification of mine tailings Continuous bioleaching is explored as a remediation technology (Borja et al., 2016). The present study aimed to develop a mixed mesophilic bacterial culture for optimal growth at high metal and solid concentration; and optimize the operating conditions of a continuous bioleaching unit. This investigation forms part of a larger study aimed to develop a bioleaching technique to treat Janggun mine tailings (Borja et al., 2017; Ngoma et al., 2017)."

Jan 1, 2018

By L. Magne, M. Maldonado, R. Varela

Real-time optimization of flotation circuits demands for accurate and reliable measurements to support the decision making process. The collection zone gas holdup is an important variable in this context as integrates the effect of machine and chemical factors on the bubble size and velocity distributions. It has been demonstrated that gas holdup not only correlates with bubble surface area flux, which defines the particle collection rate and recovery in the collection zone, but also with water overflow, a variable which has been related to the froth zone recovery. Therefore, on-line gas holdup measurements provide a reliable alternative to judge efforts leading to the optimization of flotation cells and columns. Estimation of gas holdup in flotation from electrical conductivity measurements has been proposed and extensively used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the conductivity of the liquid medium and of the mineral pulp with and without air bubbles included. These measurements require a conductivity cell which covers a representative volume of the flotation cell, and creates a homogeneous electric field throughout this volume that ideally is not affected by the conductivity of the medium. The development of such a cell in the limiting space and geometry of a laboratory flotation cell has been problematic, but a multi-electrode arrangement offers a promising alternative. Electrodes were installed in the flotation cell of a Denver unit; the results of preliminary testing are discussed with a focus on its performance in the measurement of two- and three-phase dispersion conductivity.

Jan 1, 2015

By M. J. Shields

There are numerous suggestions in the literature on methods of obtaining representative samples of waste rock or mill tailings. Some suggested methods would result in thousands of samples and very high costs for a large facility. There is no general rule that can (or should) be followed, such as collection of a given number of samples per mass of material, per acre of impoundment, or per foot of drillcore. Each site is different, and the adequacy of sampling must be tailored to the site. A logical approach is to let the variability at the site dictate the number of samples that should be collected and analyzed, and then to quantify and evaluate the results by means of standard statistical methods.

Jan 1, 1998