Search Documents

By J. D. Livingston, J. J. Becker

A MAJOR difficulty in the experimental study of precipitation-hardening is the measurement of particle sizes too small to be easily resolved with the microscope. It has been shown recently, however, that magnetic measurements on copper-cobalt al- loys in the aged state can be used to determine the average volume, total volume, volume distribution, and shape of the ferromagnetic cobalt-rich particles, even though the particles are submicroscopic in size. r' These alloys also are known to exhibit considerable precipitation hardening. This paper reports some results on the dependence of the mechanical properties of such an alloy on the particle size, determined magnetically. It further illustrates the use of other magnetic measurements in interpreting structure changes occurring during deformation.

Jan 1, 1959

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

There are two types of shovels currently used primarily as mining tools-the stripping shovel and the quarry-mine (Q-M) shovel. The two types have basically the same features, the main difference being in size. The stripping units are giant four-crawler shovels that operate by placing overburden alongside in a mined-out area. The Q-M units, on the other hand, are two-crawler shovels that usually load into trucks or trains. Powering Systems A typical stripping or Q-M shovel is fully electric, receiving power through a trailing cable that is connected to a large motor-generator set with multiple generators. In the full Ward-Leonard system, each generator furnishes d-c power to separate motors which drive the mechanisms for the principal motions of the shovel-hoist, crowd and swing.

Jan 10, 1967

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000

ADDRESS BY THE PRESIDENT OF THE INSTITUTE (MR. J. G. SYMONS) IN PRESENTING THE CERTIFICATE TO ROBERT COLVILLE BRADSHAW, O.B.E.Today it is my privilege and pleasure to introduce to you, Robert Colville Bradshaw. O.B.E., the third New Zealander to be honoured with Honorary Membership of The Institute. Sir William Hudson and Mr. C. H. Benney were the others.Mr. Bradshaw has been an Affiliate Member of The Institute since the formation of the New Zealand Branch in 1966. Like his friend Matt Benney. Bob Bradshaw is an accountant by training. Last June he retired as senior partner of the firm of chartered accountants, now known as Wilkinson Wilberfoss, with which he served from January 1929.Mr. Bradshaw grew up in New Zealand attending the Terrace School in Wellington, the New Plymouth Boys' High School where he was a boarder, and completing a Bachelor of Commerce at the university now known as the Victoria University of Wellington. He is an elected Fellow of the New Zealand Society of Accountants and an Associate of the United Kingdom Institute of Cost and Works Accountants.

Jan 1, 1977

By Edgar Urbaez

Production scheduling is one of the most important factors affecting mine planning. A program -Mine Scheduler -that aids mining engineers with the setup of an optimum open pit production scheduling algorithm has been developed. A mathematical model for open pit scheduling that optimizes the Net Present Value of the cash flows was formulated. A simulated data is formulated as a Mixed Integer Linear Programming (MILP) problem. What's Best by Lindo Systems is used as the MILP solver in Microsoft Excel. The implementation of the algorithm focuses on problem setup, allowing users to easily evaluate, simplify, and develop the model that best fits their production scheduling.

Jan 1, 1999

By Grant S. Diamond

THE BIBLIOGRAPHY on the use of static electricity in mineral beneficiation consists largely of patents. Some references are found in mineral textbooks, but very little data on flow-sheets of commercial installations are known to the writer. As a matter of fact there have been relatively few successful commercial applications of importance. Johnson prepared and published a Table showing the polarity and static field intensity requirements of many minerals. There have been reports of successful beneficiation of rutile, zir-con, coal, potassium chloride, and phosphate rock. Otherwise, the field of success has been very limited. This may be due to three reasons: first, the mining industry has been averse to dry processes, be-cause of dust nuisances in dry crushing; second, the electrostatic processes used in the past apparently developed no substantial economic advantages; and third, because flotation or other . methods have proven successful on many minerals, the industry has not felt the need for a radically different process. In the feldspar industry there was ?an attempt at electrostatic beneficiation about twenty years ago which was based on the use of fluoride fuming of the pegmatite head feed, in order to make the mineral reactive in a static field. This process was originally said to be successful, but was discontinued because of corrosion damage to machinery. Another effort by use of a chemical additive such as an or-ganic hydroxyl compound has also been attempted. Neither of these processes is known to be in use today.

Jan 1, 1957

By John K. Liu

The trend to larger grinding mills, requiring total drive power in the range of 10,000 KW(13,400 HP) or so provides the incentive for developing new power transmitting techniques, since conventional girth gears are limited to about 3700 to 4500 KW per mesh (5000-6000 HP). For the immediate future, the synchronous motor, with its beneficial power factor, and the squirrel cage induction motor, with its high reliability record and low maintenance, still promise to be the best choice for prime mover(s). Due to the abovementioned single mesh power limitation of the gear train, however, two or more motors must be combined to attain the required drive power. This paper describes a scheme for coupling these motors to the mill using a straightforward, essentially mechanical means that is based on proven components and controls.

Jan 1, 1977

By Robert F. Mehl

PROGRESS in the general field of nonferrous physical metallurgy during the past .year has been uneventful but healthy. A continued increase is apparent in the number of useful alloys and in the mechanical treatment and heat- treatment of finished metals and alloys nothing can hinder the multiplication of alloys or the diversification of their treatment as knowledge of the behavior of .alloys increases; as ternary and quaternary alloys are better understood, hundreds of new metal combinations with unusual properties may well be expected. Evidence of rapid progress is already at hand.

Jan 1, 1936

By Francis Kendorski

A longwall coal mine in Appalachia about 1,500 ft deep encountered a fault while developing a new longwall panel. The fault extended from mining depth to the surface near a secondary road and drainage. The fault was located inside the anticipated angle of draw within the mined panel and gob. The fault extended vertically out and up, away from the panel, caved zone, and gob at nearly the angle of draw: the fault very nearly following the angle of draw. It was initially thought that "fault reactivation" could possibly occur. Fault reactivation is the phenomenon of having mining subsidence localized along a fault leading to a "reactivation" of the fault and shearing and displacement along the fault. Such fault reactivation would disrupt and deform the fault plane beyond the normal angle of influence of the subsidence trough, and may provide a conduit for any ground and surface waters to reach the mine. We contacted all operators of longwall mines in Appalachia to determine if any Appalachian longwall mines had ever experienced fault reactivation, and teamed that none had experienced the phenomenon. After studies of possible water intrusion quantities and rates based upon in-fault pump tests, which indicated that water intrusion rates should be manageable, and the prior experience that faults in this particular area were usually barriers to water flow, mining proceeded with caution and monitoring. Mining was successful with no noticeable increase in water inflow rates, and no measurable off-setting of the fault exposure on the surface. It can be concluded that the fault did not reactivate due to its relationship to the mining sequence.

Jan 1, 2003

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. Datta

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function model using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance model. The appropriateness of this model is shown for different batch grinding mills.

Jan 1, 1999

By M J. Pejovic, S BoÜevski, I Miljanovic, M Hudej, A Milutinovic, A Petrovski

The paper deals with the problem of managing the supplies of consumables (energy resources, lubricants, explosives, explosive supplies, tires, spare parts, etc) in mines. After the introductory remarks and comments, a general stochastic model of supply, relating in general to the dynamic programming method is presented. A selection of stochastic supply model for experiments and research by the authors of this paper is not a coincidence, based on of their long experience, showing that this type of model is the most suitable to provide support for decision-making and management of supplies of consumables in mines.In order for the problem?of?consumables?supply?management to be reviewed, in whole and objectively from the aspect of risk, experimental tests of the stochastic model in real conditions were performed at the limestone open pit mine æZelenikovecÆ near Skopje, the capital of Macedonia. The scope of the experimental research enabled reliable analysis. The results obtained confirm the efficiency and reliability of the stochastic model and two separate manipulative-operational positions regarding its application, which may have an important influence on the optimisation of supplies.

Sep 26, 2011

Jan 1, 1956

By McHenry Mosier

Although local conditions at each mining property affect the percentage of increase in drilling speed for a given reduction in gage of bit, the results of drilling tests conducted at the Mount Weather testing adit show such a large advantage in favor of the smaller gages that they should be indicative of the possibilities at most mines. GENERAL DISCUSSION Although it is common knowledge among miners that drilling speed ill- creases with reduction in gage of bit, the large amount o this increase is not so universally realized, A recent Bureau of Mines4/ survey of drilling practices in 28 metal mines showed that the maximum gage of starters is 3 inches and that at 50 percent of the mines starters are 2-1/4 inches or larger, Because this size appears too large for conditions at most' mines where abrasion is moderate and where powder distribution permits, the use of smaller bits presents a favorable opportunity for reducing drilling costs.

Jan 1, 1939

By W. R. Bruce, G. W. Hodgson, K. A. Clark

"IntroductionANY PLANT processing mined Athabaska oil •sand for the recovery of oil produces, as a waste material, about one ton of sand for every barrel of oil recovered. A disposal problem of major proportions is thus indicated. For a 100,000-barrel per day plant, provision must be made for moving .about 4,000 tons of sand per hour on a continuous basis to a tailings dump at least several thousand feet removed from the plant site.Of the many known ways of conveying solids on .a large scale, the hydraulic pipeline transfer method is becoming increasingly important because of convenience and economy of operation. It has been in use for many years in mill operations at metalliferrous mines for the disposal of tailings and as such was a natural outgrowth of •hydraulic sluicing (3). Pipeline transportation of mill concentrates has been adopted recently ( 1), wherein high-density solids are moved several miles by hydraulic pipeline. The flotation power of the water suspending the solids may be increased 'by addition of magnetite for the handling of ore in pipelines (8). Low-density solids such as coal have received considerable study for low-cost pipe-lining (2) and a successful operation with coal has been carried out in England with indications of considerable savings over other methods of transportation (9). Dredge operations are based on pipeline transportation for the dredged sol-ids, and the scale of pipelining there .has involved pipe sizes as large as 32-inch (6). However, the tendency has been to regard the pumping of solids in water merely as a simple method of transportation and little consideration has been given in the published literature to study of the most economical modes of operating .a pipeline."

Jan 1, 1952

By H. S. COOLEY

TO talk about a "factor of economy" in connection with the wire ropes used in mining practice may be coining a new phrase. If such be the case it needs no other apology than that economy in wire rope usage is so bound up with the factor of safety as to justify a similarity in naming that makes one suggest the other. At the latest Wire Rope Research Conference, held under the auspices of the A. S. M. E., Re- search Committee and Engineering Foundation, data were introduced covering mine ropes working under

Jan 1, 1930

By M. Bouteldja

A finite element modelling approach is developed for the evaluation of the mechanical performance of cable bolts supports in underground mine structures. The modelling approach permits the simulation of any arbitrary number or pattern of cable bolts, that can be either partially or fully grouted, with or without end plates. The modelling technique used treats each cable bolt as a set of bar elements representing the steel cable. The bond stiffness characteristics of the grout bolt interface are represented by shear springs uniformly distributed along the cable length. Coupled with a simple linear elastic analysis, this technique can serve as a dedicated numerical model for cable bolted excavations. The application of the model is illustrated with two case studies: one for a hard rock mine and another for a coal mine.

Jan 1, 1999

By A. Wahab Khair

This paper presents results of the experiments carried out in Beth Energy No. 33 Mine for the purpose of alleviating problems associated with cutter roof. Cutter roof problems have delayed the advance of the entry development considerably and maintenance cost of these entries was very high due to the requirement of very extensive and heavy artificial supports. The study includes assessment of the problem, investigation of the geology and lithology of the mines, study of in-situ stresses and corrective measures to combat the problem. Two approaches were selected as the corrective measures: 1) implementing yield pillar concept in order to reduce the effects of in-situ horizontal stresses, 2) designing an effective roof reinforcement system and application procedure. Results of this study revealed that roof strata is weak and in-situ stresses are very high at the problem area which results in development of cutter roof. Implementation of yield pillar concept was found to be ineffective because cutter roof often developed at the entry face concurrent to the development. However, proper design and implementation of roof reinforcement system stabilized the roof and eliminated roof caving during both entry development and retreat of longwall face, despite existence of the cutter roof, at a much lower cost.

Jan 1, 1992

By G A. Partington

Recent research has highlighted the potential of a relatively new style of gold mineralisation related to granite intrusion. New discoveries in Alaska, Central Europe and Asia and Eastern Australia with total resources of 1600 t Au offer attractive targets for regional exploration in areas which may have been overlooked in the past. A spatial information system was developed to target granite-gold systems in eastern Australia and the West coast of New Zealand, using well constrained geological and exploration models derived from current research. Target areas were recognised in Queensland, New South Wales, Victoria, Tasmania and on the West Coast of the South Island of New Zealand that have similar spatial data relationships to known granite gold mineralisation elsewhere in the world. The second phase of the modelling better constrained the regional scale target areas by including more detailed geological, geochemical and geophysical data in the GIS to develop prospect-scale targets and to allow the acquisition of tenements over these areas. A geological review of each target area was carried out in the field to put the GIS models into context. The fieldwork has highlighted the potential for this style of mineralisation in New Zealand and will increase investment in mineral exploration and development in New Zealand in the near future.

Jan 1, 2005